Abstract: This paper describes a novel monitoring scheme to
minimize total active power in digital circuits depend on the demand
frequency, by adjusting automatically both supply voltage and
threshold voltages based on circuit operating conditions such as
temperature, process variations, and desirable frequency. The delay
monitoring results, will be control and apply so as to be maintained at
the minimum value at which the chip is able to operate for a given
clock frequency. Design details of power monitor are examined using
simulation framework in 32nm BTPM model CMOS process.
Experimental results show the overhead of proposed circuit in terms
of its power consumption is about 40 μW for 32nm technology;
moreover the results show that our proposed circuit design is not far
sensitive to the temperature variations and also process variations.
Besides, uses the simple blocks which offer good sensitivity, high
speed, the continuously feedback loop. This design provides up to
40% reduction in power consumption in active mode.
Abstract: This paper is concerned with the study of mineralogy
and engineering characteristics of soil materials derived from the
eastern part of Nile Delta. The clay minerals of the studied soil by
using X- ray diffraction are mainly illite (average 72.6 %) and
kaolinite (average 2.6 %), expandable portion in illite-smectite mixed
layer (average 7 %). Smectite is more abundant in fluviatile clays,
whereas kaolinite is more abundant in lagoonal clays. On the other
hand, illite and illite-smectite are more abundant in marine clays. The
geotechnical results show that the soil under study consists mainly of
about 0.3 % gravel, 5 % sand, 51.5 % silt and 42.2 % clay in average.
The average shrinkage limit attains 11 % whereas the average value
of the plasticity index is 23.4 %. The free swelling ranges from 40 %
to 75 % and has a value of 55 % giving an indication about the
inadequacy of such soil under foundations.
From a construction point of view, the soil under investigation
poses many problems even under light foundations due to the
swelling and shrinkage. Such swelling and shrinkage is due to the
high content of soil materials in the expandable clay minerals of illite
and smectite. Based on the results of the present and earlier studies,
trial application of soil stabilisation is recommended.
Abstract: ZnS nanoparticles of different size have been
synthesized using a colloidal particles method. Zns nanoparticles
prepared with capping agent (mercaptoethanol) then were
characterized using X-ray diffraction (XRD) and UV-Vis
spectroscopy. The particle size of the nanoparticles calculated from
the XRD patterns has been found in the range 1.85-2.44nm.
Absorption spectra have been obtained using UV-Vis
spectrophotometer to find the optical band gap and the obtained
values have been founded to being range 3.83-4.59eV. It was also
found that energy band gap increase with the increase in molar
capping agent solution.
Abstract: Authentication of multimedia contents has gained much attention in recent times. In this paper, we propose a secure semi-fragile watermarking, with a choice of two watermarks to be embedded. This technique operates in integer wavelet domain and makes use of semi fragile watermarks for achieving better robustness. A self-recovering algorithm is employed, that hides the image digest into some Wavelet subbands to detect possible malevolent object manipulation undergone by the image (object replacing and/or deletion). The Semi-fragility makes the scheme tolerant for JPEG lossy compression as low as quality of 70%, and locate the tempered area accurately. In addition, the system ensures more security because the embedded watermarks are protected with private keys. The computational complexity is reduced using parameterized integer wavelet transform. Experimental results show that the proposed scheme guarantees the safety of watermark, image recovery and location of the tempered area accurately.
Abstract: The evolution in project management was triggered by
the changes in management philosophy and practices in order to
maintain competitive advantage and continuous success in the field.
The purpose of this paper is to highlight the practicality of cognitive
style and unlearning approach in influencing the achievement of
project success by project managers. It introduces the concept of
planning, knowing and creating style from cognitive style field in the
light of achieving time, cost, quality and stakeholders appreciation in
project success context. Further it takes up a discussion of the
unlearning approach as a moderator in enhancing the relationship
between cognitive style and project success. The paper bases itself on
literature review from established disciplines like psychology,
sociology and philosophy regarding cognitive style, unlearning and
project success in general. The analysis and synthesis of literature in
the subject area a conceptual paper is utilized as the basis of future
research to form a comprehensive framework for project managers in
enhancing the project management competency.
Abstract: This study was carried out to evaluate concentration
of micro minerals (Zn, Fe, Mn, Cu and Se) of forages and their
distribution in fiber fraction (neutral detergent fiber/NDF and acid
detergent fiber/ADF) in South Sumatra during dry and rainy seasons.
Seven species of commonly forages namely Axonopus compressus,
Panicum maximum, Pennisetum purpuphoides, Leucaena
leucocephala, Centrocema pubescens, Calopogonium mucunoides
and Acacia mangium were collected at native pasture during rainy
and dry seasons. The results showed that micro minerals
concentration of forages and their distribution in fiber fraction varied
among species and season. In general, concentration of micro
minerals was slightly higher in rainy season compared to dry season
either in grass or legumes forages. In grass, concentration of Fe and
Mn were above the critical level, while 33.3 %, 100 % and 16.7 % of
evaluated grass were deficient in Zn, Cu and Se. Data on legume
forages show that 75 % of legumes were deficient in Zn and Mn, 62.5
% deficient in Cu and 50 % deficient in Se. There was no species of
legume deficient in Fe. Distribution of micro minerals in NDF and
ADF were also significantly affected by species and season and
depends on the kinds of element measured. Generally, micro minerals
were associated in fiber fractions much higher during dry season
compared to rainy season. Iron (Fe) and selenium (Se) in forages
were the highest elements associated in NDF and ADF, while the
lowest was found in Copper (Cu).
Abstract: Designing modern machine tools is a complex task. A
simulation tool to aid the design work, a virtual machine, has
therefore been developed in earlier work. The virtual machine
considers the interaction between the mechanics of the machine
(including structural flexibility) and the control system. This paper
exemplifies the usefulness of the virtual machine as a tool for product
development. An optimisation study is conducted aiming at
improving the existing design of a machine tool regarding weight and
manufacturing accuracy at maintained manufacturing speed. The
problem can be categorised as constrained multidisciplinary multiobjective
multivariable optimisation. Parameters of the control and
geometric quantities of the machine are used as design variables. This
results in a mix of continuous and discrete variables and an
optimisation approach using a genetic algorithm is therefore
deployed. The accuracy objective is evaluated according to
international standards. The complete systems model shows nondeterministic
behaviour. A strategy to handle this based on statistical
analysis is suggested. The weight of the main moving parts is reduced
by more than 30 per cent and the manufacturing accuracy is
improvement by more than 60 per cent compared to the original
design, with no reduction in manufacturing speed. It is also shown
that interaction effects exist between the mechanics and the control,
i.e. this improvement would most likely not been possible with a
conventional sequential design approach within the same time, cost
and general resource frame. This indicates the potential of the virtual
machine concept for contributing to improved efficiency of both
complex products and the development process for such products.
Companies incorporating such advanced simulation tools in their
product development could thus improve its own competitiveness as
well as contribute to improved resource efficiency of society at large.
Abstract: MicroRNAs (miRNAs) are a class of non-coding
RNAs that hybridize to mRNAs and induce either translation
repression or mRNA cleavage. Recently, it has been reported that
miRNAs could possibly play an important role in human diseases. By
integrating miRNA target genes, cancer genes, miRNA and mRNA
expression profiles information, a database is developed to link
miRNAs to cancer target genes. The database provides experimentally
verified human miRNA target genes information, including oncogenes
and tumor suppressor genes. In addition, fragile sites information for
miRNAs, and the strength of the correlation of miRNA and its target
mRNA expression level for nine tissue types are computed, which
serve as an indicator for suggesting miRNAs could play a role in
human cancer. The database is freely accessible at
http://ppi.bioinfo.asia.edu.tw/mirna_target/index.html.
Abstract: Shipping comb is mounted on Head Stack Assembly
(HSA) to prevent collision of the heads, maintain the gap between
suspensions and protect HSA tips from unintentional contact
damaged in the manufacturing process. Failure analysis of shipping
comb in hard disk drive production processes is proposed .Field
observations were performed to determine the fatal areas on shipping
comb and their failure fraction. Root cause failure analysis (RCFA) is
applied to specify the failure causes subjected to various loading
conditions. For reliability improvement, failure mode and effects
analysis (FMEA) procedure to evaluate the risk priority is performed.
Consequently, the more suitable information design criterions were
obtained.
Abstract: In the present paper, we-ll explore how social media tools provide an opportunity for new developments of the e-Learning in the context of managing personal knowledge. There will be a discussion how social media tools provide a possibility for helping knowledge workersand students to gather, organize and manage their personal information as a part of the e-learning process. At the centre of this social software driven approach to e-learning environments are the challenges of personalization and collaboration. We-ll share concepts of how organizations are using social media for e-Learning and believe that integration of these tools into traditional e-Learning is probably not a choice, but inevitability. Students- Survey of use of web technologies and social networking tools is presented. Newly developed framework for semantic blogging capable of organizing results relevant to user requirements is implemented at Varna Free University (VFU) to provide more effective navigation and search.
Abstract: n-CdO/p-Si heterojunction diode was fabricated using
sol-gel spin coating technique which is a low cost and easily scalable
method for preparing of semiconductor films. The structural and
morphological properties of CdO film were investigated. The X-ray
diffraction (XRD) spectra indicated that the film was of
polycrystalline nature. The scanning electron microscopy (SEM)
images indicate that the surface morphology CdO film consists of the
clusters formed with the coming together of the nanoparticles. The
electrical characterization of Au/n-CdO/p–Si/Al heterojunction diode
was investigated by current-voltage. The ideality factor of the diode
was found to be 3.02 for room temperature. The reverse current of
the diode strongly increased with illumination intensity of 100
mWcm-2 and the diode gave a maximum open circuit voltage Voc of
0.04 V and short-circuits current Isc of 9.92×10-9 A.
Abstract: The purpose of this research is to develop a security model for voice eavesdropping protection over digital networks. The proposed model provides an encryption scheme and a personal secret key exchange between communicating parties, a so-called voice data transformation system, resulting in a real-privacy conversation. The operation of this system comprises two main steps as follows: The first one is the personal secret key exchange for using the keys in the data encryption process during conversation. The key owner could freely make his/her choice in key selection, so it is recommended that one should exchange a different key for a different conversational party, and record the key for each case into the memory provided in the client device. The next step is to set and record another personal option of encryption, either taking all frames or just partial frames, so-called the figure of 1:M. Using different personal secret keys and different sets of 1:M to different parties without the intervention of the service operator, would result in posing quite a big problem for any eavesdroppers who attempt to discover the key used during the conversation, especially in a short period of time. Thus, it is quite safe and effective to protect the case of voice eavesdropping. The results of the implementation indicate that the system can perform its function accurately as designed. In this regard, the proposed system is suitable for effective use in voice eavesdropping protection over digital networks, without any requirements to change presently existing network systems, mobile phone network and VoIP, for instance.
Abstract: In this paper, a new reversible watermarking method is presented that reduces the size of a stereoscopic image sequence while keeping its content visible. The proposed technique embeds the residuals of the right frames to the corresponding frames of the left sequence, halving the total capacity. The residual frames may result in after a disparity compensated procedure between the two video streams or by a joint motion and disparity compensation. The residuals are usually lossy compressed before embedding because of the limited embedding capacity of the left frames. The watermarked frames are visible at a high quality and at any instant the stereoscopic video may be recovered by an inverse process. In fact, the left frames may be exactly recovered whereas the right ones are slightly distorted as the residuals are not embedded intact. The employed embedding method reorders the left frame into an array of consecutive pixel pairs and embeds a number of bits according to their intensity difference. In this way, it hides a number of bits in intensity smooth areas and most of the data in textured areas where resulting distortions are less visible. The experimental evaluation demonstrates that the proposed scheme is quite effective.
Abstract: Existing underground pipe jacking methods use a
reinforcing rod in a steel tube to obtain structural stiffness. However,
some problems such as inconvenience of works and expensive
materials resulted from limited working space and reinforcing works
are existed. To resolve these problems, a new pipe jacking method,
namely PST (Prestressed Segment Tunnel) method, was developed
which used joint to connect the steel segment and form erection
structure. For evaluating the flexural capacity of the PST method
structure, a experimental test was conducted. The parameters
considered in the test were span-to-depth ratio of segment, diameter of
steel tube at the corner, prestressing force, and welding of joint. The
flexural behaviours with the effect of load capacity in serviceability
state according to different parameters were examined.. The frame
with long segments could increase flexural stiffness and the specimen
with large diameter of concave corner showed excellent resistance
ability to the negative moment. In addition, welding of joints increased
the flexural capacity.
Abstract: This paper deals with behavior and capacity of
punching shear force for flat slabs produced from steel fiber
reinforced self compacting concrete (SFRSCC) by application
nonlinear finite element method. Nonlinear finite element analysis on
nine slab specimens was achieved by using ANSYS software. A
general description of the finite element method, theoretical modeling
of concrete and reinforcement are presented. The nonlinear finite
element analysis program ANSYS is utilized owing to its capabilities
to predict either the response of reinforced concrete slabs in the post
elastic range or the ultimate strength of a flat slabs produced from
steel fiber reinforced self compacting concrete (SFRSCC). In order to
verify the analytical model used in this research using test results of
the experimental data, the finite element analysis were performed
then a parametric study of the effect ratio of flexural reinforcement,
ratio of the upper reinforcement, and volume fraction of steel fibers
were investigated. A comparison between the experimental results
and those predicted by the existing models are presented. Results and
conclusions may be useful for designers, have been raised, and
represented.
Abstract: In this paper we present a novel method, which
reduces the computational complexity of abrupt cut detection. We
have proposed fast algorithm, where the similarity of frames within
defined step is evaluated instead of comparing successive frames.
Based on the results of simulation on large video collection, the
proposed fast algorithm is able to achieve 80% reduction of needed
frames comparisons compared to actually used methods without the
shot cut detection accuracy degradation.
Abstract: The paper reflects current state of popularization of
static elasticity modulus of concrete. This parameter is undoubtedly
very important for designing of concrete structures, and very often
neglected and rarely determined before designing concrete
technology itself. The paper describes assessment and comparison of
four mix designs with almost constant dosage of individual
components. The only difference is area of origin of small size
fraction of aggregate 0/4. Development of compressive strength and
static elasticity modulus at the age of 7, 28 and 180 days were
observed. As the experiment showed, designing of individual
components and their quality are the basic factor influencing
elasticity modulus of current concrete.
Abstract: Meta-reasoning is essential for multi-agent communication. In this paper we propose a framework of multi-agent communication in which agents employ meta-reasoning to reason with agent and ontology locations in order to communicate semantic information with other agents on the semantic web and also reason with multiple distributed ontologies. We shall argue that multi-agent communication of Semantic Web information cannot be realized without the need to reason with agent and ontology locations. This is because for an agent to be able to communicate with another agent, it must know where and how to send a message to that agent. Similarly, for an agent to be able to reason with an external semantic web ontology, it must know where and how to access to that ontology. The agent framework and its communication mechanism are formulated entirely in meta-logic.
Abstract: In this investigation, anatase TiO2 thin films were
grown by radio frequency magnetron sputtering on glass substrates at
a high sputtering pressure and room temperature. The anatase films
were then annealed at 300-600 °C in air for a period of 1 hour. To
examine the structure and morphology of the films, X-ray diffraction
(XRD) and atomic force microscopy (AFM) methods were used
respectively. From X-ray diffraction patterns of the TiO2 films, it was
found that the as-deposited film showed some differences compared
with the annealed films and the intensities of the peaks of the
crystalline phase increased with the increase of annealing
temperature. From AFM images, the distinct variations in the
morphology of the thin films were also observed. The optical
constants were characterized using the transmission spectra of the
films obtained by UV-VIS-IR spectrophotometer. Besides, optical
thickness of the film deposited at room temperature was calculated
and cross-checked by taking a cross-sectional image through SEM.
The optical band gaps were evaluated through Tauc model. It was
observed that TiO2 films produced at room temperatures exhibited
high visible transmittance and transmittance decreased slightly with
the increase of annealing temperatures. The films were found to be
crystalline having anatase phase. The refractive index of the films
was found from 2.31-2.35 in the visible range. The extinction
coefficient was nearly zero in the visible range and was found to
increase with annealing temperature. The allowed indirect optical
band gap of the films was estimated to be in the range from 3.39 to
3.42 eV which showed a small variation. The allowed direct band
gap was found to increase from 3.67 to 3.72 eV. The porosity was
also found to decrease at a higher annealing temperature making the
film compact and dense.
Abstract: In this study the mixed mode fracture mechanics
parameters were investigated for high tensile steel butt welded joint
based on modified Arcan test and finite element analysis was used to
evaluate the effect of crack length on fracture criterion. The nondimensional
stress intensity factors, strain energy release rates and Jintegral
energy on crack tip were obtained for various in-plane
loading combinations on Arcan specimen starting from pure mode-I
to pure mode-II loading conditions. The specimen and apparatus were
modeled by finite element method and analyzed under various
loading angles (between 0 to 90 degrees with 15 degree interval) to
simulate the pure mode-I, II and mixed mode fracture. Since the
analytical results are independent from elasticity modules for
isotropic materials, therefore the results in elastic fields can be used
for Arcan specimens. The main objective of this study was to
evaluate the geometric calibration factors for modified Arcan test
specimen in order to obtain fracture toughness under mixed mode
loading conditions.