Abstract: A specially designed flat plate was mounted vertically
over the axial line in the wind tunnel of the Aerospace Department of
the Pusan National University. The plate is 2 m long, 0.8 m high and 8
cm thick. The measurements were performed in velocity range from
15 to 60 m/s. A sand paper turbulizer was placed close to the plate nose
to provide fully developed turbulent boundary layer over the most part
of the plate. Strain balances were mounted in the trailing part of the
plate to measure the skin friction drag over removable insertions of
0.55×0.25m2 size. A set of the insertions was designed and
manufactured: 3mm thick polished metal surface and three compliant
surfaces. The compliant surfaces were manufactured of a silicone
rubber Silastic® S2 (Dow Corning company). To modify the
viscoelastic properties of the rubber, its composition was varied: 90%
of the rubber + 10% catalyst (standard), 92.5% + 7.5% (weak), 85% +
15% (strong). Modulus of elasticity and the loss tangent were
measured accurately for these materials in the frequency range from
40 Hz to 3 KHz using the unique proposed technique.
Abstract: Determination of nano particle size is substantial since
the nano particle size exerts a significant effect on various properties
of nano materials. Accordingly, proposing non-destructive, accurate
and rapid techniques for this aim is of high interest. There are some
conventional techniques to investigate the morphology and grain size
of nano particles such as scanning electron microscopy (SEM),
atomic force microscopy (AFM) and X-ray diffractometry (XRD).
Vibrational spectroscopy is utilized to characterize different
compounds and applied for evaluation of the average particle size
based on relationship between particle size and near infrared spectra
[1,4] , but it has never been applied in quantitative morphological
analysis of nano materials. So far, the potential application of nearinfrared
(NIR) spectroscopy with its ability in rapid analysis of
powdered materials with minimal sample preparation, has been
suggested for particle size determination of powdered
pharmaceuticals. The relationship between particle size and diffuse
reflectance (DR) spectra in near infrared region has been applied to
introduce a method for estimation of particle size. Back propagation
artificial neural network (BP-ANN) as a nonlinear model was applied
to estimate average particle size based on near infrared diffuse
reflectance spectra. Thirty five different nano TiO2 samples with
different particle size were analyzed by DR-FTNIR spectrometry and
the obtained data were processed by BP- ANN.
Abstract: The purpose of this paper is to consider the
introduction of online courses to replace the current classroom-based
staff training. The current training is practical, and must be
completed before access to the financial computer system is
authorized. The long term objective is to measure the efficacy,
effectiveness and efficiency of the training, and to establish whether
a transfer of knowledge back to the workplace has occurred. This
paper begins with an overview explaining the importance of staff
training in an evolving, competitive business environment and
defines the problem facing this particular organization. A summary
of the literature review is followed by a brief discussion of the
research methodology and objective. The implementation of the
alpha version of the online course is then described. This paper may
be of interest to those seeking insights into, or new theory regarding,
practical interventions of online learning in the real world.
Abstract: A new strain of Type A influenza virus can cause the
transmission of H1N1 virus. This virus can spread between the
people by coughing and sneezing. Because the people are always
movement, so this virus can be easily spread. In this study, we
construct the dynamical network model of H1N1 virus by separating
the human into five groups; susceptible, exposed, infectious,
quarantine and recovered groups. The movement of people between
houses (local level) is considered. The behaviors of solutions to our
dynamical model are shown for the different parameters.
Abstract: An attempt has been made to determine the strength
and impact properties of Cr-Mo steel weld and base materials by
varying the current during manual metal arc welding. Toughness over
a temperature range from -32 to 100°C of base, heat affected zone
(HAZ) and weld zones at three current settings are made. It is
observed that the deterioration in notch toughness at any zone with
the temperature decreases. The values of notch toughness for all
zones at -32°C are almost same for any current settings. The values
of notch toughness at HAZ area are higher than that of weld area due
to the coarsening of ferrite grain of HAZ occurs with higher heat
input. From microhardness and microstructure result, it can be
concluded that large inclusion content in weld deposit is the cause of
lower notch toughness value.
Abstract: In order to investigate water deficit stress on 24 of
soybean (Glycine Max. L) cultivars and lines in temperate climate, an
experiment was conducted in Iran Seed and Plant Improvement
Institute. Stress levels were irrigation after evaporation of 50, 100,
150 mm water from pan, class A. Randomized Completely Block
Design was arranged for each stress levels. Some traits such as, node
number, plant height, pod number per area, grain number per pod,
grain number per area, 1000 grains weight, grain yield and harvest
index were measured. Results showed that water deficit stress had
significant effect on node number, plant height, pod number per area,
grain number per pod, grain number per area, 1000 grains weight and
harvest index. Also all of agronomic traits except harvest index
influenced significantly by cultivars and lines. The least and most
grain yield was belonged to Ronak X Williams and M41 x Clark
respectively.
Abstract: In recent years, many researches to mine the exploding Web world, especially User Generated Content (UGC) such as
weblogs, for knowledge about various phenomena and events in the physical world have been done actively, and also Web services
with the Web-mined knowledge have begun to be developed for
the public. However, there are few detailed investigations on how accurately Web-mined data reflect physical-world data. It must be
problematic to idolatrously utilize the Web-mined data in public Web services without ensuring their accuracy sufficiently. Therefore,
this paper introduces the simplest Web Sensor and spatiotemporallynormalized
Web Sensor to extract spatiotemporal data about a target
phenomenon from weblogs searched by keyword(s) representing the
target phenomenon, and tries to validate the potential and reliability of the Web-sensed spatiotemporal data by four kinds of granularity
analyses of coefficient correlation with temperature, rainfall, snowfall,
and earthquake statistics per day by region of Japan Meteorological
Agency as physical-world data: spatial granularity (region-s population
density), temporal granularity (time period, e.g., per day vs. per week), representation granularity (e.g., “rain" vs. “heavy rain"), and
media granularity (weblogs vs. microblogs such as Tweets).
Abstract: Environmental statistics reveals that the pollution of
acid rain in South Korea is a serious issue. Yet the awareness of people
is low. Even after a gradual decrease of pollutant emission in Korea,
the acidity has not been reduced. There no boundaries in the
atmosphere are set and the influence of the neighboring countries such
as China is apparent. Governmental efforts among China, Japan and
Korea have been made on this issue. However, not much progress has
been observed. Along with the governmental activities, therefore, an
active monitoring of the pollution among the countries and the
promotion of environmental awareness at the civil level including
especially the middle and high schools are highly recommended. It
will be this young generation who will face damaged country as
inheritance not the current generation.
Abstract: The influence of human activities produced by dams
along the river beds is minor, but the location of accumulation of
water directly influences the hydrological regime. The most
important effect of the influence of damming on the way water flows
decreases the frequency of floods. The water rate controls the water
flow of the dams. These natural reservoirs become dysfunctional and,
as a result, a new distribution of flow in the downstream sector,
where maximum flow is, brings about, in this case, higher values. In
addition to fishing, middle and lower courses of rivers located by
accumulation also have a role in mitigating flood waves, thus
providing flood protection. The Vaslui also ensures a good part of the
needs of the town water supply. The most important lake is Solesti,
close to the Vaslui River, opened in 1974. A hydrological regime of
accumulation is related to an anthropogenic and natural drainage
system. The design conditions and their manoeuvres drain or fill the
water courses.
Abstract: The pavement constructions on soft and expansive soils are not durable and unable to sustain heavy traffic loading. As a result, pavement failures and settlement problems will occur very often even under light traffic loading due to cyclic and rolling effects. Geotechnical engineers have dwelled deeply into this matter, and adopt various methods to improve the engineering characteristics of soft fine-grained soils and expansive soils. The problematic soils are either replaced by good and better quality material or treated by using chemical stabilization with various binding materials. Increased the strength and durability are also the part of the sustainability drive to reduce the environment footprint of the built environment by the efficient use of resources and waste recycle materials. This paper presents a series of laboratory tests and evaluates the effect of cement and fly ash on the strength and drainage characteristics of soil in Miri. The tests were performed at different percentages of cement and fly ash by dry weight of soil. Additional tests were also performed on soils treated with the combinations of fly ash with cement and lime. The results of this study indicate an increase in unconfined compression strength and a decrease in hydraulic conductivity of the treated soil.
Abstract: Information and Communication Technologies (ICT) are increasing in importance everyday, especially since the 90’s (last decade of birth for the Millennials generation). While social interactions involving the Millennials generation have been studied, a lack of investigation remains regarding the use of the ICT by this generation as well as the impact on outcomes in education and professional training. Observing and interviewing students preparing a MSc, we aimed at characterizing the interaction students-ICT during the courses. We found that up to 50% of the students (mainly female) could use ICT during courses at a rate of 0.84 occurrence/minutes for some of them, and they thought this involvement did not disturb learning, even was helpful. As recent researches show that multitasking leads people think they are much better than they actually are, further observations with assessments are needed to conclude whether or not the use ICT by students during the courses is a real strength.
Abstract: Quality of 2D and 3D cross-sectional images produce
by Computed Tomography primarily depend upon the degree of
precision of primary and secondary X-Ray intensity detection.
Traditional method of primary intensity detection is apt to errors.
Recently the X-Ray intensity measurement system along with smart
X-Ray sensors is developed by our group which is able to detect
primary X-Ray intensity unerringly. In this study a new smart X-Ray
sensor is developed using Light-to-Frequency converter TSL230
from Texas Instruments which has numerous advantages in terms of
noiseless data acquisition and transmission. TSL230 construction is
based on a silicon photodiode which converts incoming X-Ray
radiation into the proportional current signal. A current to frequency
converter is attached to this photodiode on a single monolithic CMOS
integrated circuit which provides proportional frequency count to
incoming current signal in the form of the pulse train. The frequency
count is delivered to the center of PICDEM FS USB board with
PIC18F4550 microcontroller mounted on it. With highly compact
electronic hardware, this Demo Board efficiently read the smart
sensor output data. The frequency output approaches overcome
nonlinear behavior of sensors with analog output thus un-attenuated
X-Ray intensities could be measured precisely and better
normalization could be acquired in order to attain high resolution.
Abstract: This paper presents a heuristic to solve large size 0-1 Multi constrained Knapsack problem (01MKP) which is NP-hard. Many researchers are used heuristic operator to identify the redundant constraints of Linear Programming Problem before applying the regular procedure to solve it. We use the intercept matrix to identify the zero valued variables of 01MKP which is known as redundant variables. In this heuristic, first the dominance property of the intercept matrix of constraints is exploited to reduce the search space to find the optimal or near optimal solutions of 01MKP, second, we improve the solution by using the pseudo-utility ratio based on surrogate constraint of 01MKP. This heuristic is tested for benchmark problems of sizes upto 2500, taken from literature and the results are compared with optimum solutions. Space and computational complexity of solving 01MKP using this approach are also presented. The encouraging results especially for relatively large size test problems indicate that this heuristic can successfully be used for finding good solutions for highly constrained NP-hard problems.
Abstract: Seismic design may require non-conventional
concept, due to the fact that the stiffness and layout of the structure
have a great effect on the overall structural behaviour, on the seismic
load intensity as well as on the internal force distribution. To find an
economical and optimal structural configuration the key issue is the
optimal design of the lateral load resisting system. This paper focuses
on the optimal design of regular, concentric braced frame (CBF)
multi-storey steel building structures. The optimal configurations are
determined by a numerical method using genetic algorithm approach,
developed by the authors. Aim is to find structural configurations
with minimum structural cost. The design constraints of objective
function are assigned in accordance with Eurocode 3 and Eurocode 8
guidelines. In this paper the results are presented for various building
geometries, different seismic intensities, and levels of energy
dissipation.
Abstract: The selection of parents and breeding strategies for
the successful maize hybrid production will be facilitated by
heterotic groupings of parental lines and determination of combining
abilities of them. Fourteen maize inbred lines, used in maize breeding
programs in Iran, were crossed in a diallel mating design. The 91 F1
hybrids and the 14 parental lines were studied during two years at
four locations of Iran for investigation of combining ability of
gentypes for grain yield and to determine heterotic patterns among
germplasm sources, using both, the Griffing-s method and the biplot
approach for diallel analysis. The graphical representation offered by
biplot analysis allowed a rapid and effective overview of general
combining ability (GCA) and specific combining ability (SCA)
effects of the inbred lines, their performance in crosses, as well as
grouping patterns of similar genotypes. GCA and SCA effects were
significant for grain yield (GY). Based on significant positive GCA
effects, the lines derived from LSC could be used as parent in crosses
to increase GY. The maximum best- parent heterosis values and
highest SCA effects resulted from crosses B73 × MO17 and A679 ×
MO17 for GY. The best heterotic patterns were LSC × RYD, which
would be potentially useful in maize breeding programs to obtain
high-yielding hybrids in the same climate of Iran.
Abstract: This paper proposes the concept of aerocapture with
aerodynamic-environment-adaptive variable geometry flexible
aeroshell that vehicle deploys. The flexible membrane is composed
of thin-layer film or textile as its aeroshell in order to solve some
problems obstructing realization of aerocapture technique.
Multi-objective optimization study is conducted to investigate
solutions and derive design guidelines. As a result, solutions which
can avoid aerodynamic heating and enlarge the corridor width up
to 10% are obtained successfully, so that the effectiveness of this
concept can be demonstrated. The deformation-use optimum
solution changes its drag coefficient from 1.6 to 1.1, along with the
change in dynamic pressure. Moreover, optimization results show
that deformation-use solution requires the membrane for which
upper temperature limit and strain limit are more than 700 K and
120%, respectively, and elasticity (Young-s modulus) is of order of
106 Pa.
Abstract: The possibility of using cassava residue containing
49.66% starch, 21.47% cellulose, 12.97% hemicellulose, and 21.86%
lignin as a raw material to produce glucose using enzymatic
hydrolysis was investigated. In the experiment, each reactor
contained the cassava residue, bacteria cells, and production medium.
The effects of particles size (40 mesh and 60 mesh) and strains of
bacteria (A002 and M015) isolated from Thai higher termites,
Microcerotermes sp., on the glucose concentration at 37°C were
focused. High performance liquid chromatography (HPLC) with a
refractive index detector was used to determine the quantity of
glucose. The maximum glucose concentration obtained at 37°C using
strain A002 and 60 mesh of the cassava residue was 1.51 g/L at 10 h.
Abstract: Recently, a great amount of interest has been shown
in the field of modeling and controlling hybrid systems. One of the
efficient and common methods in this area utilizes the mixed logicaldynamical
(MLD) systems in the modeling. In this method, the
system constraints are transformed into mixed-integer inequalities by
defining some logic statements. In this paper, a system containing
three tanks is modeled as a nonlinear switched system by using the
MLD framework. Comparing the model size of the three-tank system
with that of a two-tank system, it is deduced that the number of
binary variables, the size of the system and its complexity
tremendously increases with the number of tanks, which makes the
control of the system more difficult. Therefore, methods should be
found which result in fewer mixed-integer inequalities.
Abstract: In this paper, a new technique of signal detection has been proposed for detecting the orthogonal frequency-division multiplexing (OFDM) signal in the presence of nonlinear distortion.There are several advantages of OFDM communications system.However, one of the existing problems is remain considered as the nonlinear distortion generated by high-power-amplifier at the transmitter end due to the large dynamic range of an OFDM signal. The proposed method is the maximum likelihood detection with the symbol estimation. When the training data are available, the neural network has been used to learn the characteristic of received signal and to estimate the new positions of the transmitted symbol which are provided to the maximum likelihood detector. Resulting in the system performance, the nonlinear distortions of a traveling wave tube amplifier with OFDM signal are considered in this paper.Simulation results of the bit-error-rate performance are obtained with 16-QAM OFDM systems.
Abstract: Although many studies on the assembly technology of
the bridge construction have dealt mostly with on the pier, girder or the
deck of the bridge, studies on the prefabricated barrier have rarely been
performed. For understanding structural characteristics and
application of the concrete barrier in the modular bridge, which is an
assembly of structure members, static loading test was performed.
Structural performances as a road barrier of the three methods,
conventional cast-in-place(ST), vertical bolt connection(BVC) and
horizontal bolt connection(BHC) were evaluated and compared
through the analyses of load-displacement curves, strain curves of the
steel, concrete strain curves and the visual appearances of crack
patterns. The vertical bolt connection(BVC) method demonstrated
comparable performance as an alternative to conventional
cast-in-place(ST) while providing all the advantages of prefabricated
technology. Necessities for the future improvement in nuts
enforcement as well as legal standard and regulation are also
addressed.