Abstract: Significant legislative changes are set to revolutionise the commercial shipping industry. Upcoming emissions restrictions will force operators to look at technologies that can improve the efficiency of their vessels -reducing fuel consumption and emissions. A device which may help in this challenge is the Ship Wind-Assisted Propulsion system (SWAP), an actively controlled aerofoil mounted vertically on the deck of a ship. The device functions in a similar manner to a sail on a yacht, whereby the aerodynamic forces generated by the sail reach an equilibrium with the hydrodynamic forces on the hull and a forward velocity results. Numerical and experimental testing of the SWAP device is presented in this study. Circulation control takes the form of a co-flow jet aerofoil, utilising both blowing from the leading edge and suction from the trailing edge. A jet at the leading edge uses the Coanda effect to energise the boundary layer in order to delay flow separation and create high lift with low drag. The SWAP concept has been originated by the research and development team at SMAR Azure Ltd. The device will be retrofitted to existing ships so that a component of the aerodynamic forces acts forward and partially reduces the reliance on existing propulsion systems. Wind tunnel tests have been carried out at the de Havilland wind tunnel at the University of Glasgow on a 1:20 scale model of this system. The tests aim to understand the airflow characteristics around the aerofoil and investigate the approximate lift and drag coefficients that an early iteration of the SWAP device may produce. The data exhibits clear trends of increasing lift as injection momentum increases, with critical flow attachment points being identified at specific combinations of jet momentum coefficient, Cµ, and angle of attack, AOA. Various combinations of flow conditions were tested, with the jet momentum coefficient ranging from 0 to 0.7 and the AOA ranging from 0° to 35°. The Reynolds number across the tested conditions ranged from 80,000 to 240,000. Comparisons between 2D computational fluid dynamics (CFD) simulations and the experimental data are presented for multiple Reynolds-Averaged Navier-Stokes (RANS) turbulence models in the form of normalised surface pressure comparisons. These show good agreement for most of the tested cases. However, certain simulation conditions exhibited a well-documented shortcoming of RANS-based turbulence models for circulation control flows and over-predicted surface pressures and lift coefficient for fully attached flow cases. Work must be continued in finding an all-encompassing modelling approach which predicts surface pressures well for all combinations of jet injection momentum and AOA.
Abstract: Numerical modeling of fluid flows, whether compressible or incompressible, laminar or turbulent presents a considerable contribution in the scientific and industrial fields. However, the development of an approximate model of a supersonic flow requires the introduction of specific and more precise techniques and methods. For this purpose, the object of this paper is modeling a supersonic flow of inviscid fluid around a dihedral airfoil. Based on the thin airfoils theory and the non-dimensional stationary Steichen equation of a two-dimensional supersonic flow in isentropic evolution, we obtained a solution for the downstream velocity potential of the oblique shock at the second order of relative thickness that characterizes a perturbation parameter. This result has been dealt with by the asymptotic analysis and characteristics method. In order to validate our model, the results are discussed in comparison with theoretical and experimental results. Indeed, firstly, the comparison of the results of our model has shown that they are quantitatively acceptable compared to the existing theoretical results. Finally, an experimental study was conducted using the AF300 supersonic wind tunnel. In this experiment, we have considered the incident upstream Mach number over a symmetrical dihedral airfoil wing. The comparison of the different Mach number downstream results of our model with those of the existing theoretical data (relative margin between 0.07% and 4%) and with experimental results (concordance for a deflection angle between 1° and 11°) support the validation of our model with accuracy.
Abstract: The aim of the research work is to modify the NACA 4215 airfoil with flap and rotary cylinder at the leading edge of the airfoil and experimentally study the static pressure distribution over the airfoil completed with flap and leading-edge vortex generator. In this research, NACA 4215 wing model has been constructed by generating the profile geometry using the standard equations and design software such as AutoCAD and SolidWorks. To perform the experiment, three wooden models are prepared and tested in subsonic wind tunnel. The experiments were carried out in various angles of attack. Flap angle and momentum injection rate are changed to observe the characteristics of pressure distribution. In this research, a new concept of flow separation control mechanism has been introduced to improve the aerodynamic characteristics of airfoil. Control of flow separation over airfoil which experiences a vortex generator (rotating cylinder) at the leading edge of airfoil is experimentally simulated under the effects of momentum injection. The experimental results show that the flow separation control is possible by the proposed mechanism, and benefits can be achieved by momentum injection technique. The wing performance is significantly improved due to control of flow separation by momentum injection method.
Abstract: Wind tunnel experiments for aerodynamic profiles display numerous advantages, such as: clean steady laminar flow, controlled environmental conditions, streamlines visualization, and real data acquisition. However, the experiment instrumentation usually is expensive, and hence, each test implies a incremented in design cost. The aim of this work is to select and implement a low-cost static pressure data acquisition system for a NACA 2412 airfoil in an open cycle wind tunnel. This work compares wind tunnel experiment with Computational Fluid Dynamics (CFD) simulation and parametric analysis. The experiment was evaluated at Reynolds of 1.65 e5, with increasing angles from -5° to 15°. The comparison between the approaches show good enough accuracy, between the experiment and CFD, additional parametric analysis results differ widely from the other methods, which complies with the lack of accuracy of the lateral approach due its simplicity.
Abstract: This paper presents an experimental investigation for the characteristics of an energy harvesting device exploiting flow-induced vibration in a wind tunnel. A stationary bluff body is connected with a downstream tip body via an aluminium cantilever beam. Various lengths of aluminium cantilever beam and different shapes of downstream tip body are considered. The results show that the characteristics of the energy harvester’s vibration depend on both the length of the aluminium cantilever beam and the shape of the downstream tip body. The highest ratio between vibration amplitude and bluff body diameter was found to be 1.39 for an energy harvester with a symmetrical triangular tip body and L/D1 = 5 at 9.8 m/s of flow speed (Re = 20077). Using this configuration, the electrical energy was extracted with a polyvinylidene fluoride (PVDF) piezoelectric beam with different load resistances, of which the optimal value could be found on each Reynolds number. The highest power output was found to be 3.19 µW, at 9.8 m/s of flow speed (Re = 20077) and 27 MΩ of load resistance.
Abstract: Supersonic wind tunnel nozzles are generally capable of producing a constant Mach number flow in the test section of the wind tunnel. As a result, most of the supersonic vehicles are widely designed using steady state flow characteristics which may have errors while facing unsteady situations. This study aims to explore the possibility of varying the Mach number of the flow during wind tunnel operation. The nozzle walls are restricted to be inflexible for cooling near the throat due to high stagnation temperature requirement of the flow to simulate the conditions as experienced by the vehicle. Two simple independent mechanisms, rotation and translation of nozzle walls have been analyzed and the nozzle ranges have been optimized to vary the Mach number from Mach 2 to Mach 5 using minimum number of nozzles in the wind tunnel.
Abstract: This paper presents an analytical study of Small Unmanned Aerial Vehicle (SUAV) dynamic stability derivatives. Simulating SUAV dynamics and analyzing its behavior at the earliest design stages is too important and more efficient design aspect. The approach suggested in this paper is using the wind tunnel experiment to collect the aerodynamic data and get the dynamic stability derivatives. AutoCAD Software was used to draw the case study (wildlife surveillance SUAV). The SUAV is scaled down to be 0.25% of the real SUAV dimensions and converted to a wind tunnel model. The model was tested in three different speeds for three different attitudes which are; pitch, roll and yaw. The wind tunnel results were then used to determine the case study stability derivative values, and hence it used to calculate the roots of the characteristic equation for both longitudinal and lateral motions. Finally, the characteristic equation roots were found and discussed in all possible cases.
Abstract: The simulation in wind tunnel is used thoroughly to model real situations of drainages of air. Besides the automotive industry, a great number of applications can be numbered: dispersion of pollutant, studies of pedestrians’ comfort, and dispersion of particles. This work had the objective of visualizing the characteristics aerodynamics of two automobiles in different ways. To accomplish that drainage of air a fan that generated a speed exists (measured with anemometer of hot thread) of 4,1m/s and 4,95m/s. To visualize the path of the air through the cars, in the wind tunnel, smoke was used, obtained with it burns of vegetable oil. For “to do smoke” vegetable oil was used, that was burned for a tension of 20V generated by a thread of 2,5mm. The cars were placed inside of the wind tunnel with the drainage of “air-smoke” and photographed, registering like this the path lines around them, in the 3 different speeds.
Abstract: This paper investigates the characteristics of wall
pressure fluctuations in naturally developing boundary layer flows
on axisymmetric bodies experimentally. The axisymmetric body has
a modified ellipsoidal blunt nose. Flush-mounted microphones are
used to measure the wall pressure fluctuations in the boundary layer
flow over the body. The measurements are performed in a low noise
wind tunnel. It is found that the correlation between the flow regime
and the characteristics of the pressure fluctuations is distinct. The
process from small fluctuation in laminar flow to large fluctuation in
turbulent flow is investigated. Tollmien-Schlichting wave (T-S wave)
is found to generate and develop in transition. Because of the T-S
wave, the wall pressure fluctuations in the transition region are higher
than those in the turbulent boundary layer.
Abstract: This paper reports an experimental investigation of the energy spectrum of turbulent velocity fields at low Reynolds numbers in grid turbulence. Hot wire measurements are carried out in grid turbulence with subjected to a 1.36:1 contraction of the wind tunnel. Three different grids are used: (i) large square perforated grid (mesh size 43.75mm), (ii) small square perforated grid (mesh size 14. and (iii) woven mesh grid (mesh size 5mm). The results indicate that the energy spectrum at small Reynolds numbers does not follow Kolmogorov’s universal scaling. It is further found that the critical Reynolds number, below which the scaling breaks down, is around 25.
Abstract: Traditionally, wind tunnel models are made of metal
and are very expensive. In these years, everyone is looking for ways
to do more with less. Under the right test conditions, a rapid
prototype part could be tested in a wind tunnel. Using rapid prototype
manufacturing techniques and materials in this way significantly
reduces time and cost of production of wind tunnel models. This
study was done of fused deposition modeling (FDM) and their ability
to make components for wind tunnel models in a timely and cost
effective manner. This paper discusses the application of wind tunnel
model configuration constructed using FDM for transonic wind
tunnel testing. A study was undertaken comparing a rapid
prototyping model constructed of FDM Technologies using
polycarbonate to that of a standard machined steel model. Testing
covered the Mach range of Mach 0.3 to Mach 0.75 at an angle-ofattack
range of - 2° to +12°. Results from this study show relatively
good agreement between the two models and rapid prototyping
Method reduces time and cost of production of wind tunnel models.
It can be concluded from this study that wind tunnel models
constructed using rapid prototyping method and materials can be
used in wind tunnel testing for initial baseline aerodynamic database
development.
Abstract: The aerodynamics characteristics of a blended-wing body (BWB) aircraft were obtained in Universiti Teknologi MARA low speed wind tunnel. The scaled-down of BWB model consisted of a canard as its horizontal stabilizer. There were four canards with different aspect ratio used in the experiments. Canard setting angles were varied from -20q to 20q. All tests were conducted at velocity of 35 m/s, with Mach number 0.1. At low angles of attacks, the increment of lift slope for various canards aspect ratio is small and almost constant. Higher canard aspect ratio will cause higher drag. However, canard has a high effect to the moment at zero lift, CM,0.The visualization using mini tuff was performed to observe the airflow at the upper surface of canard. KeywordsAerodynamics,blended-wing body, canard, wind tunnel.
Abstract: A series of experiments were carried out to study
unsteady behavior of the flow field as well as the boundary layer of
an airfoil oscillating in plunging motion in a subsonic wind tunnel.
The measurements involved surface pressure distribution
complimented with surface-mounted hot-films. The effect of leadingedge
roughness that simulates surface irregularities on the wind
turbine blades was also studied on variations of aerodynamic loads
and boundary layer behavior.
Abstract: Shear-layer instabilities of a pulsed stack-issued
transverse jet were studied experimentally in a wind tunnel. Jet
pulsations were induced by means of acoustic excitation. Streak
pictures of the smoke-flow patterns illuminated by the laser-light sheet
in the median plane were recorded with a high-speed digital camera.
Instantaneous velocities of the shear-layer instabilities in the flow were
digitized by a hot-wire anemometer. By analyzing the streak pictures
of the smoke-flow visualization, three characteristic flow modes,
synchronized flapping jet, transition, and synchronized shear-layer
vortices, are identified in the shear layer of the pulsed stack-issued
transverse jet at various excitation Strouhal numbers. The shear-layer
instabilities of the pulsed stack-issued transverse jet are synchronized
by acoustic excitation except for transition mode. In transition flow
mode, the shear-layer vortices would exhibit a frequency that would be
twice as great as the acoustic excitation frequency.
Abstract: A specially designed flat plate was mounted vertically
over the axial line in the wind tunnel of the Aerospace Department of
the Pusan National University. The plate is 2 m long, 0.8 m high and 8
cm thick. The measurements were performed in velocity range from
15 to 60 m/s. A sand paper turbulizer was placed close to the plate nose
to provide fully developed turbulent boundary layer over the most part
of the plate. Strain balances were mounted in the trailing part of the
plate to measure the skin friction drag over removable insertions of
0.55×0.25m2 size. A set of the insertions was designed and
manufactured: 3mm thick polished metal surface and three compliant
surfaces. The compliant surfaces were manufactured of a silicone
rubber Silastic® S2 (Dow Corning company). To modify the
viscoelastic properties of the rubber, its composition was varied: 90%
of the rubber + 10% catalyst (standard), 92.5% + 7.5% (weak), 85% +
15% (strong). Modulus of elasticity and the loss tangent were
measured accurately for these materials in the frequency range from
40 Hz to 3 KHz using the unique proposed technique.
Abstract: This paper deals with the conceptual design of the
new aeroelastic demonstrator for the whirl flutter simulation. The
paper gives a theoretical background of the whirl flutter phenomenon
and describes the events of the whirl flutter occurrence in the
aerospace practice. The second part is focused on the experimental
research of the whirl flutter on aeroelastic similar models. Finally the
concept of the new aeroelastic demonstrator is described. The
demonstrator represents the wing and engine of the twin turboprop
commuter aircraft including a driven propeller. It allows the changes
of the main structural parameters influencing the whirl flutter
stability characteristics. It is intended for the experimental
investigation of the whirl flutter in the wind tunnel. The results will
be utilized for validation of analytical methods and software tools.