Abstract: In this paper, we investigated the athermal pressure
behavior of the structural and elastic properties of scheelite BaWO4
phase up to 7 GPa using the ab initio pseudo-potential method. The
calculated lattice parameters pressure relation have been compared
with the experimental values and found to be in good agreement with
these results. Moreover, we present for the first time the investigation
of the elastic properties of this compound using the density functional
perturbation theory (DFPT). It is shown that this phase is
mechanically stable up to 7 GPa after analyzing the calculated elastic
constants. Other relevant quantities such as bulk modulus, pressure
derivative of bulk modulus, shear modulus; Young’s modulus,
Poisson’s ratio, anisotropy factors, Debye temperature and sound
velocity have been calculated. The obtained results, which are
reported for the first time to the best of the author’s knowledge, can
facilitate assessment of possible applications of the title material.
Abstract: This paper proposed the comparison made between
Multi-Carrier Pulse Width Modulation, Sinusoidal Pulse Width
Modulation and Selective Harmonic Elimination Pulse Width
Modulation technique for minimization of Total Harmonic Distortion
in Cascaded H-Bridge Multi-Level Inverter. In Multicarrier Pulse
Width Modulation method by using Alternate Position of Disposition
scheme for switching pulse generation to Multi-Level Inverter.
Another carrier based approach; Sinusoidal Pulse Width Modulation
method is also implemented to define the switching pulse generation
system in the multi-level inverter. In Selective Harmonic Elimination
method using Genetic Algorithm and Particle Swarm Optimization
algorithm for define the required switching angles to eliminate low
order harmonics from the inverter output voltage waveform and
reduce the total harmonic distortion value. So, the results validate that
the Selective Harmonic Elimination Pulse Width Modulation method
does capably eliminate a great number of precise harmonics and
minimize the Total Harmonic Distortion value in output voltage
waveform in compared with Multi-Carrier Pulse Width Modulation
method, Sinusoidal Pulse Width Modulation method. In this paper,
comparison of simulation results shows that the Selective Harmonic
Elimination method can attain optimal harmonic minimization
solution better than Multi-Carrier Pulse Width Modulation method,
Sinusoidal Pulse Width Modulation method.
Abstract: In addition to environmental parameters like rain,
temperature diseases on crop is a major factor which affects
production quality & quantity of crop yield. Hence disease
management is a key issue in agriculture. For the management of
disease, it needs to be detected at early stage. So, treat it properly &
control spread of the disease. Now a day, it is possible to use the
images of diseased leaf to detect the type of disease by using image
processing techniques. This can be achieved by extracting features
from the images which can be further used with classification
algorithms or content based image retrieval systems. In this paper,
color image is used to extract the features such as mean and standard
deviation after the process of region cropping. The selected features
are taken from the cropped image with different image size samples.
Then, the extracted features are taken in to the account for
classification using Fuzzy Inference System (FIS).
Abstract: This study aimed to determine the possible protective effects of L‐carnitine against gentamicin‐induced nephrotoxicity. Forty male albino rats were divided into 4 groups (10 rats each); Group 1: normal control, group 2: induced nephrotoxicity (gentamicin 50 mg/kg/day S.C; 8 days), group 3: treated with L‐ carnitine (40 mg/kg/d SC for 12 days) and group 4: treated with L‐ carnitine 4 days before and for 8 days in concomitant with gentamicin. Gentamicin‐induced nephrotoxicity (group 2): caused significant increase in serum urea, creatinine, urinary N‐acetyl‐B‐D‐ glucosaminidase (NAG), gamma glutamyl transpeptidase (GGT), urinary total protein and kidney tissue malondialdehyde (MDA) with significant decrease in serum superoxide dismutase (SOD), serum catalase and creatinine clearance and marked tubular necrosis in the proximal convoluted tubules with interruption in the basement membrane around the necrotic tubule compared to the normal control group. L‐carnitine 4 days before and for 8 days in concomitant with gentamicin (group 4) offered marked decrease in serum urea, serum creatinine, urinary NAG, urinary GGT, urinary proteins and kidney tissue MDA, with marked increase in serum SOD, serum catalase and creatinine clearance with marked improvement in the tubular damage compared to gentamicin‐induced nephrotoxicity group. L‐carnitine administered for 12 days produced no change in the parameters mentioned above as compared to the normal control group. In conclusion: L‐carnitine could reduce most of the biochemical parameters and also improve the histopathological features of kidney asscociated with gentamicin induced‐nephrotoxicity.
Abstract: Hemoglobin (HB) indicates anemia level and by
extension may reflect the nutritional level and perhaps the immunity
of an individual. Some antiretroviral drugs like Zidovudine are
known to cause anemia in people living with HIV/AIDS (PLWHA).
A cross sectional study using demographic data and blood specimen
from 218 female commercial sex workers attending antiretroviral
therapy (ART) clinics was conducted between December, 2009 and
July, 2011 to assess the effect of zidovudine on hematologic, and
RNA viral load of female sex workers receiving antiretroviral
treatment in north western Nigeria. Anemia is a common and serious
complication of both HIV infection and its treatment. In the setting of
HIV infection, anemia has been associated with decreased quality of
life, functional status, and survival. Antiretroviral therapy,
particularly the highly active antiretroviral therapy (HAART), has
been associated with a decrease in the incidence and severity of
anemia in HIV-infected patients who have received a HAART
regimen for at least 1 year. In this study, result has shown that of the
218 patients, 26 with hemoglobin count between 5.1 – 10g/dl were
observed to have the highest viral load count of 300,000 –
350,000copies/ml. It was also observed that most patients (190) with
HB of 10.1 – 15.0g/dl had viral load count of 200,000 – 250,000
copies /ml. An inverse relationship therefore exists i.e. the lower the
hemoglobin level, the higher the viral load count even though the test
statistics did not show any significance between the two (P = 0.206).
This shows that multivariate logistic regression analysis
demonstrated that anemia was associated with a CD4 + cell count
below 50/μL, female sex workers with a viral load above 100,000
copies/mL, who use zidovudine.
Severe anemia was less prevalent in this study population than in
historical comparators; however, mild to moderate anemia rates
remain high. The study therefore recommends that hematological and
virologic parameters be monitored closely in patients receiving first
line ART regimen.
Abstract: The numerical simulation has made tremendous
advances in investigating the blood flow phenomenon through elastic
arteries. Such study can be useful in demonstrating the disease
progression and hemodynamics of cardiovascular diseases such as
atherosclerosis. In the present study, patient specific case diagnosed
with partially stenosed complete right ICA and normal left carotid
bifurcation without any atherosclerotic plaque formation is
considered. 3D patient specific carotid bifurcation model is generated
based on CT scan data using MIMICS-4.0 and numerical analysis is
performed using FSI solver in ANSYS-14.5. The blood flow is
assumed to be incompressible, homogenous and Newtonian, while
the artery wall is assumed to be linearly elastic. The two-way
sequentially coupled transient FSI analysis is performed using FSI
solver for three pulse cycles. The hemodynamic parameters such as
flow pattern, Wall Shear Stress, pressure contours and arterial wall
deformation are studied at the bifurcation and critical zones such as
stenosis. The variation in flow behavior is studied throughout the
pulse cycle. Also, the simulation results reveal that there is a
considerable increase in the flow behavior in stenosed carotid in
contrast to the normal carotid bifurcation system. The investigation
also demonstrates the disturbed flow pattern especially at the
bifurcation and stenosed zone elevating the hemodynamics,
particularly during peak systole and later part of the pulse cycle. The
results obtained agree well with the clinical observation and
demonstrates the potential of patient specific numerical studies in
prognosis of disease progression and plaque rupture.
Abstract: We report herein the development and preliminary mechanical characterization of fully-dense multi-wall carbon nanotube (MWCNT)-reinforced ceramics and glasses based on a completely new methodology termed High Shear Compaction (HSC). The tubes are introduced and bound to the matrix grains by aid of polymeric binders to form flexible green bodies which are sintered and densified by spark plasma sintering to unprecedentedly high densities of 100% of the pure-matrix value. The strategy was validated across a PyrexTM glass / MWCNT composite while no identifiable factors limit application to other types of matrices. Nondestructive evaluation, based on ultrasonics, of the dynamic mechanical properties of the materials including elastic, shear and bulk modulus as well as Poisson’s ratio showed optimum property improvement at 0.5 %wt tube loading while evidence of nanoscalespecific energy dissipative characteristics acting complementary to nanotube bridging and pull-out indicate a high potential in a wide range of reinforcing and multifunctional applications.
Abstract: Information generated from various computerization processes is a potential rich source of knowledge for its designated community. To pass this information from generation to generation without modifying the meaning is a challenging activity. To preserve and archive the data for future generations it’s very essential to prove the authenticity of the data. It can be achieved by extracting the metadata from the data which can prove the authenticity and create trust on the archived data. Subsequent challenge is the technology obsolescence. Metadata extraction and standardization can be effectively used to resolve and tackle this problem. Metadata can be categorized at two levels i.e. Technical and Domain level broadly. Technical metadata will provide the information that can be used to understand and interpret the data record, but only this level of metadata isn’t sufficient to create trustworthiness. We have developed a tool which will extract and standardize the technical as well as domain level metadata. This paper is about the different features of the tool and how we have developed this.
Abstract: The crude methanol extracts of five indigenous vegetables namely, Amarathus tricolor, Basella rubra L., Chochurus olitorius L., Ipomea batatas, and Momordica chuchinensis L., were examined for their phytochemical profile and antioxidant activity using 1,1-diphenyl-2-picrylhydrazyl (DPPH) free radical. The values for DPPH radical scavenging activity ranged from 7.6-89.53% with B. rubra and I. batatas having the lowest and highest values, respectively. The total flavonoid content of all five indigenous vegetables ranged from 74.65-277.3 mg quercetin equivalent per gram of dried vegetable material while the total phenolic content ranged from 1.93-6.15 mg gallic acid equivalent per gram dried material. Phytochemical screening revealed the presence of steroids, flavonoids, saponins, tannins, carbohydrates and reducing sugars, which may also be associated with the antioxidant activity shown by these indigenous vegetables.
Abstract: In the present study, response surface methodology has been used to optimize turn-assisted deep cold rolling process of AISI 4140 steel. A regression model is developed to predict surface hardness and surface roughness using response surface methodology and central composite design. In the development of predictive model, deep cold rolling force, ball diameter, initial roughness of the workpiece, and number of tool passes are considered as model variables. The rolling force and the ball diameter are the significant factors on the surface hardness and ball diameter and numbers of tool passes are found to be significant for surface roughness. The predicted surface hardness and surface roughness values and the subsequent verification experiments under the optimal operating conditions confirmed the validity of the predicted model. The absolute average error between the experimental and predicted values at the optimal combination of parameter settings for surface hardness and surface roughness is calculated as 0.16% and 1.58% respectively. Using the optimal processing parameters, the surface hardness is improved from 225 to 306 HV, which resulted in an increase in the near surface hardness by about 36% and the surface roughness is improved from 4.84µm to 0.252 µm, which resulted in decrease in the surface roughness by about 95%. The depth of compression is found to be more than 300µm from the microstructure analysis and this is in correlation with the results obtained from the microhardness measurements. Taylor hobson talysurf tester, micro vickers hardness tester, optical microscopy and X-ray diffractometer are used to characterize the modified surface layer.
Abstract: Given the limited research on Small and Mediumsized
Enterprises’ (SMEs) contribution to Corporate Social
Responsibility (CSR) and even scarcer research on Swiss SMEs, this
paper helps to fill these gaps by enabling the identification of supranational
SME parameters. Thus, the paper investigates the current
state of SME practices in Switzerland and across 15 other countries.
Combining the degree to which SMEs demonstrate an explicit (or
business case) approach or see CSR as an implicit moral activity with
the assessment of their attributes for “variety of capitalism” defines
the framework of this comparative analysis. To outline Swiss small
business CSR patterns in particular, 40 SME owner-managers were
interviewed. A secondary data analysis of studies from different
countries laid groundwork for this comparative overview of small
business CSR. The paper identifies Swiss small business CSR as
driven by norms, values, and by the aspiration to contribute to
society, thus, as an implicit part of the day-to-day business. Similar to
most Central European, Mediterranean, Nordic, and Asian countries,
explicit CSR is still very rare in Swiss SMEs. Astonishingly, also
British and American SMEs follow this pattern in spite of their strong
and distinctly liberal market economies. Though other findings show
that nationality matters this research concludes that SME culture and
an informal CSR agenda are strongly formative and superseding even
forces of market economies, nationally cultural patterns, and
language. Hence, classifications of countries by their market system,
as found in the comparative capitalism literature, do not match the
CSR practices in SMEs as they do not mirror the peculiarities of their
business. This raises questions on the universality and
generalisability of unmediated, explicit management concepts,
especially in the context of small firms.
Abstract: In the years followed independence, an economic
crisis and some conflicts led to the displacement of many people
inside Georgia. The growing poverty, unemployment, low income
and its unequal distribution limited access to basic social service have
had a clear direct impact on Georgian population dynamics and its
age-sex structure. Factors influencing the changing population age
structure and urbanization include mortality, fertility, migration and
expansion of urban. In this paper presents the main factors of
changing the distribution by urban and rural areas. How different are
the urban and rural age and sex structures? Does Georgia have the
same age-sex structure among their urban and rural populations since
1950s?
Abstract: In this study, three robust predicting methods, namely artificial neural network (ANN), adaptive neuro fuzzy inference system (ANFIS) and support vector machine (SVM) were used for computing the resonant frequency of A-shaped compact microstrip antennas (ACMAs) operating at UHF band. Firstly, the resonant frequencies of 144 ACMAs with various dimensions and electrical parameters were simulated with the help of IE3D™ based on method of moment (MoM). The ANN, ANFIS and SVM models for computing the resonant frequency were then built by considering the simulation data. 124 simulated ACMAs were utilized for training and the remaining 20 ACMAs were used for testing the ANN, ANFIS and SVM models. The performance of the ANN, ANFIS and SVM models are compared in the training and test process. The average percentage errors (APE) regarding the computed resonant frequencies for training of the ANN, ANFIS and SVM were obtained as 0.457%, 0.399% and 0.600%, respectively. The constructed models were then tested and APE values as 0.601% for ANN, 0.744% for ANFIS and 0.623% for SVM were achieved. The results obtained here show that ANN, ANFIS and SVM methods can be successfully applied to compute the resonant frequency of ACMAs, since they are useful and versatile methods that yield accurate results.
Abstract: Obesity and osteoporosis are the two diseases whose
increasing prevalence and high impact on the global morbidity and
mortality, during the two recent decades, have gained a status of
major health threats worldwide. Obesity purports to affect the bone
metabolism through complex mechanisms. Debated data on the
connection between the bone mineral density and fracture prevalence
in the obese patients are widely presented in literature. There is
evidence that the correlation of weight and fracture risk is sitespecific.
This study is aimed at determining the connection between
the bone mineral density (BMD) and trabecular bone score (TBS)
parameters in Ukrainian women suffering from obesity. We
examined 1025 40-89-year-old women, divided them into the groups
according to their body mass index: Group A included 360 women
with obesity whose BMI was ≥30 kg/m2, and Group B – 665 women
with no obesity and BMI of
Abstract: This paper reviews the model-based qualitative and
quantitative Operations Management research in the context of
Construction Supply Chain Management (CSCM). Construction
industry has been traditionally blamed for low productivity, cost and
time overruns, waste, high fragmentation and adversarial
relationships. The construction industry has been slower than other
industries to employ the Supply Chain Management (SCM) concept
and develop models that support the decision-making and planning.
However the last decade there is a distinct shift from a project-based
to a supply-based approach of construction management. CSCM
comes up as a new promising management tool of construction
operations and improves the performance of construction projects in
terms of cost, time and quality. Modeling the Construction Supply
Chain (CSC) offers the means to reap the benefits of SCM, make
informed decisions and gain competitive advantage. Different
modeling approaches and methodologies have been applied in the
multi-disciplinary and heterogeneous research field of CSCM. The
literature review reveals that a considerable percentage of the CSC
modeling research accommodates conceptual or process models
which present general management frameworks and do not relate to
acknowledged soft Operations Research methods. We particularly
focus on the model-based quantitative research and categorize the
CSCM models depending on their scope, objectives, modeling
approach, solution methods and software used. Although over the last
few years there has been clearly an increase of research papers on
quantitative CSC models, we identify that the relevant literature is
very fragmented with limited applications of simulation,
mathematical programming and simulation-based optimization. Most
applications are project-specific or study only parts of the supply
system. Thus, some complex interdependencies within construction
are neglected and the implementation of the integrated supply chain
management is hindered. We conclude this paper by giving future
research directions and emphasizing the need to develop optimization
models for integrated CSCM. We stress that CSC modeling needs a
multi-dimensional, system-wide and long-term perspective. Finally,
prior applications of SCM to other industries have to be taken into
account in order to model CSCs, but not without translating the
generic concepts to the context of construction industry.
Abstract: Intermittent behavior near the boundary of phase
synchronization in the presence of noise is studied. In certain range of
the coupling parameter and noise intensity the intermittency of eyelet
and ring intermittencies is shown to take place. Main results are
illustrated using the example of two unidirectional coupled Rössler
systems. Similar behavior is shown to take place in two
hydrodynamical models of Pierce diode coupled unidirectional.
Abstract: Designing cost-efficient, secure network protocols for
Wireless Sensor Networks (WSNs) is a challenging problem because
sensors are resource-limited wireless devices. Security services such
as authentication and improved pairwise key establishment are
critical to high efficient networks with sensor nodes. For sensor
nodes to correspond securely with each other efficiently, usage of
cryptographic techniques is necessary. In this paper, two key
predistribution schemes that enable a mobile sink to establish a
secure data-communication link, on the fly, with any sensor nodes.
The intermediate nodes along the path to the sink are able to verify
the authenticity and integrity of the incoming packets using a
predicted value of the key generated by the sender’s essential power.
The proposed schemes are based on the pairwise key with the mobile
sink, our analytical results clearly show that our schemes perform
better in terms of network resilience to node capture than existing
schemes if used in wireless sensor networks with mobile sinks.
Abstract: This research aims to develop an algorithm to
generate a schedule of multiple cranes that will maximize load
throughputs in anodizing operation. The algorithm proposed utilizes
an enumerative strategy to search for constant time between
successive loads and crane covering range over baths. The computer
program developed is able to generate a near-optimal crane schedule
within reasonable times, i.e. within 10 minutes. Its results are
compared with existing solutions from an aluminum extrusion
industry. The program can be used to generate crane schedules for
mixed products, thus allowing mixed-model line balancing to
improve overall cycle times.
Abstract: The aim of this investigation is to elaborate nearinfrared
methods for testing and recognition of chemical components
and quality in “Pannon wheat” allied (i.e. true to variety or variety
identified) milling fractions as well as to develop spectroscopic
methods following the milling processes and evaluate the stability of
the milling technology by different types of milling products and
according to sampling times, respectively. These wheat categories
produced under industrial conditions where samples were collected
versus sampling time and maximum or minimum yields. The changes
of the main chemical components (such as starch, protein, lipid) and
physical properties of fractions (particle size) were analysed by
dispersive spectrophotometers using visible (VIS) and near-infrared
(NIR) regions of the electromagnetic radiation. Close correlation
were obtained between the data of spectroscopic measurement
techniques processed by various chemometric methods (e.g. principal
component analysis [PCA], cluster analysis [CA]) and operation
condition of milling technology. It is obvious that NIR methods are
able to detect the deviation of the yield parameters and differences of
the sampling times by a wide variety of fractions, respectively. NIR
technology can be used in the sensitive monitoring of milling
technology.
Abstract: Submerged arc welding is a very complex process. It
is a very efficient and high performance welding process. In this
present study an attempt have been done to reduce the welding
distortion by increased amount of oxide flux through TiO2 in
submerged arc welding process. Care has been taken to avoid the
excessiveness of the adding agent for attainment of significant
results. Data Envelopment Analysis (DEA) based BAT algorithm is
used for the parametric optimization purpose in which DEA is used
to convert multi response parameters into a single response
parameter. The present study also helps to know the effectiveness of
the addition of TiO2 in active flux during submerged arc welding
process.