Abstract: RF magnetron sputtering is used on the ceramic targets,
each of which contains zinc oxide (ZnO), zinc oxide doped with
aluminum (AZO) and zinc oxide doped with gallium (GZO). The XRD
analysis showed a preferred orientation along the (002) plane for ZnO,
AZO, and GZO films. The AZO film had the best electrical properties;
it had the lowest resistivity of 6.6 × 10-4 cm, the best sheet resistance of
2.2 × 10-1 Ω/square, and the highest carrier concentration of 4.3 × 1020
cm-3, as compared to the ZnO and GZO films.
Abstract: The effects of flame-holder position, the ratio of flame
holder diameter to combustion chamber diameter and injection angle
on fuel propulsive droplets sizing and effective mass fraction have
been studied by a cold flow. We named the mass of fuel vapor inside
the flammability limit as the effective mass fraction. An empty
cylinder as well as a flame-holder which are a simulator for duct
combustion has been considered. The airflow comes into the cylinder
from one side and injection operation will be done by four nozzles
which are located on the entrance of cylinder. To fulfill the
calculations a modified version of KIVA-3V code which is a
transient, three-dimensional, multiphase, multi component code for
the analysis of chemically reacting flows with sprays, is used.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: Distillery spentwash contains high chemical oxygen
demand (COD), biological oxygen demand (BOD), color, total
dissolved solids (TDS) and other contaminants even after biological
treatment. The effluent can’t be discharged as such in the surface
water bodies or land without further treatment. Reverse osmosis (RO)
treatment plants have been installed in many of the distilleries at
tertiary level in many of the distilleries in India, but are not properly
working due to fouling problem which is caused by the presence of
high concentration of organic matter and other contaminants in
biologically treated spentwash. In order to make the membrane
treatment a proven and reliable technology, proper pre-treatment is
mandatory. In the present study, ultra-filtration (UF) for pretreatment
of RO at tertiary stage has been performed. Operating
parameters namely initial pH (pHo: 2–10), trans-membrane pressure
(TMP: 4-20 bars) and temperature (T: 15-43°C) were used for
conducting experiments with UF system. Experiments were
optimized at different operating parameters in terms of COD, color,
TDS and TOC removal by using response surface methodology
(RSM) with central composite design. The results showed that
removal of COD, color and TDS was 62%, 93.5% and 75.5%
respectively, with UF, at optimized conditions with increased
permeate flux from 17.5 l/m2/h (RO) to 38 l/m2/h (UF-RO). The
performance of the RO system was greatly improved both in term of
pollutant removal as well as water recovery.
Abstract: Biodiesel production from vegetable oil will produce
glycerol as by-product about 10% of the biodiesel production. The
amount of glycerol that was produced needed alternative way to
handling immediately so as to not become the waste that polluted
environment. One of the solutions was to process glycerol to
polyglycidyl nitrate (PGN). PGN is synthesized from glycerol by
three-step reactions i.e. nitration of glycerol, cyclization of 13-
dinitroglycerine and polymerization of glycosyl nitrate. Optimum
condition of nitration of glycerol with nitric acid has not been known.
Thermodynamic feasibility should be done before run experiments in
the laboratory. The aim of this study was to determine the parameters
those affect nitration of glycerol and nitric acid and chose the
operation condition. Many parameters were simulated to verify its
possibility to experiment under conditions which would get the
highest conversion of 1, 3-dinitroglycerine and which was the ideal
condition to get it. The parameters that need to be studied to obtain
the highest conversion of 1, 3-dinitroglycerine were mol ratio of
nitric acid/glycerol, reaction temperature, mol ratio of
glycerol/dichloromethane and pressure. The highest conversion was
obtained in the range of mol ratio of nitric acid /glycerol between 2/1
– 5/1, reaction temperature of 5-25oC and pressure of 1 atm. The
parameters that need to be studied further to obtain the highest
conversion of 1.3 DNG are mol ratio of nitric acid/glycerol and
reaction temperature.
Abstract: The main parameters affecting the workability are the
water content, particle size, and the total surface of the grains, as long
as the mixing water begins by wetting the surface of the grains and
then fills the voids between the grains to form entrapped water, the
quantity of water remaining is called free water. The aim of this study is to undertake a fractal approach through
the relationship between the concrete formulation parameters and
workability. To develop this approach a series of concrete taken from
the literature was investigated by varying formulation parameters
such as G/S, the quantity of cement C and the quantity of water W. We also call another model as the model of water layer thickness
and model of paste layer thickness to judge their relevance, hence the
following results: the relevance of the water layer thickness model is
considered as a relevant when there is a variation in the water
quantity. The model of the paste layer thickness is only applicable if
we considered that the paste is made with the grain value Dmax =
2.85: value from which we see a stability of the model.
Abstract: We apply the non-parametric, unconditional,
hyperbolic order-α quantile estimator to appraise the relative
efficiency of Microfinance Institutions in Africa in terms of outreach.
Our purpose is to verify if these institutions, which must constantly
try to strike a compromise between their social role and financial
sustainability are operationally efficient.
Using data on African MFIs extracted from the Microfinance
Information eXchange (MIX) database and covering the 2004 to
2006 periods, we find that more efficient MFIs are also the most
profitable. This result is in line with the view that social performance
is not in contradiction with the pursuit of excellent financial
performance. Our results also show that large MFIs in terms of asset
and those charging the highest fees are not necessarily the most
efficient.
Abstract: In this study, nuclear magnetic resonance
spectroscopy and nuclear quadrupole resonance spectroscopy
parameters of 14N (Nitrogen in imidazole ring) in N–H…O hydrogen
bonding for Histidine hydrochloride monohydrate were calculated via
density functional theory. We considered a five-molecule model
system of Histidine hydrochloride monohydrate. Also we examined
the trends of environmental effect on hydrogen bonds as well as
cooperativity. The functional used in this research is M06-2X which
is a good functional and the obtained results has shown good
agreement with experimental data. This functional was applied to
calculate the NMR and NQR parameters. Some correlations among
NBO parameters, NMR and NQR parameters have been studied
which have shown the existence of strong correlations among them.
Furthermore, the geometry optimization has been performed using
M062X/6-31++G(d,p) method. In addition, in order to study
cooperativity and changes in structural parameters, along with
increase in cluster size, natural bond orbitals have been employed.
Abstract: This paper investigates the parametric stability of an
axially moving web subjected to non-uniform in-plane edge
excitations on two opposite, simply-supported edges. The web is
modeled as a viscoelastic plate whose constitutive relation obeys the
Kelvin-Voigt model, and the in-plane edge excitations are expressed
as the sum of a static tension and a periodical perturbation. Due to the
in-plane edge excitations, the moving plate may bring about
parametric instability under certain situations. First, the in-plane
stresses of the plate due to the non-uniform edge excitations are
determined by solving the in-plane forced vibration problem. Then,
the dependence on the spatial coordinates in the equation of transverse
motion is eliminated by the generalized Galerkin method, which
results in a set of discretized system equations in time. Finally, the
method of multiple scales is utilized to solve the set of system
equations analytically if the periodical perturbation of the in-plane
edge excitations is much smaller as compared with the static tension of
the plate, from which the stability boundaries of the moving plate are
obtained. Numerical results reveal that only combination resonances
of the summed-type appear under the in-plane edge excitations
considered in this work.
Abstract: In this paper, influence of harmonics on medium
voltage distribution system of Bogazici Electricity Distribution Inc.
(BEDAS) which takes place at Istanbul/Turkey is investigated. A ring
network consisting of residential loads is taken into account for this
study. Real system parameters and measurement results are used for
simulations. Also, probable working conditions of the system are
analyzed for 50%, 75%, and 100% loading of transformers with
similar harmonic contents. Results of the study are exhibited the
influence of nonlinear loads on %THDV, P.F. and technical losses of
the medium voltage distribution system.
Abstract: Lead time is a critical measure of a supply chain's
performance. It impacts both the customer satisfactions as well as the
total cost of inventory. This paper presents the result of a study on the
analysis of the customer order lead-time for a multinational company.
In the study, the lead time was divided into three stages respectively:
order entry, order fulfillment, and order delivery. A sample of size 2,425 order lines was extracted from the
company's records to use for this study. The sample data entails
information regarding customer orders from the time of order entry
until order delivery. Data regarding the lead time of each stage for
different orders were also provided. Summary statistics on lead time
data reveals that about 30% of the orders were delivered later than the
scheduled due date. The result of the multiple linear regression
analysis technique revealed that component type, logistics parameter,
order size and the customer type have significant impacts on lead
time. Data analysis on the stages of lead time indicates that stage 2
consumed over 50% of the lead time. Pareto analysis was made to
study the reasons for the customer order delay in each stage.
Recommendation was given to resolve the problem.
Abstract: In this paper, we present a four-step ortho-rectification
procedure for real-time geo-referencing of video data from a low-cost
UAV equipped with a multi-sensor system. The basic procedures for
the real-time ortho-rectification are: (1) decompilation of the video
stream into individual frames; (2) establishing the interior camera
orientation parameters; (3) determining the relative orientation
parameters for each video frame with respect to each other; (4)
finding the absolute orientation parameters, using a self-calibration
bundle and adjustment with the aid of a mathematical model. Each
ortho-rectified video frame is then mosaicked together to produce a
mosaic image of the test area, which is then merged with a well
referenced existing digital map for the purpose of geo-referencing
and aerial surveillance. A test field located in Abuja, Nigeria was
used to evaluate our method. Video and telemetry data were collected
for about fifteen minutes, and they were processed using the four-step
ortho-rectification procedure. The results demonstrated that the
geometric measurement of the control field from ortho-images is
more accurate when compared with those from original perspective
images when used to pin point the exact location of targets on the
video imagery acquired by the UAV. The 2-D planimetric accuracy
when compared with the 6 control points measured by a GPS receiver
is between 3 to 5 metres.
Abstract: The environmental, cultural, social, and technological
changes have led higher education institutes to question their
traditional roles. Many declarations and frameworks highlight the
importance of fulfilling social responsibility of higher education
institutes. The study aims at developing a framework of university
social responsibility and sustainability (USR&S) with focus on South
Valley University (SVU) as a case study of Egyptian Universities.
The study used meetings with 12 vice deans of community services
and environmental affairs on social responsibility and environmental
issues. The proposed framework integrates social responsibility with
strategic management through the establishment and maintenance of
the vision, mission, values, goals and management systems;
elaboration of policies; provision of actions; evaluation of services
and development of social collaboration with stakeholders to meet
current and future needs of the community and environment. The
framework links between different stakeholders internally and
externally using communication and reporting tools. The results show
that SVU integrates social responsibility and sustainability in its
strategic plans. It has policies and actions however fragmented and
lack of appropriate structure and budgeting. The proposed framework
could be valuable for researchers and decision makers of the
Egyptian Universities. The study proposed recommendations and
highlighted building on the results and conducting future research.
Abstract: Numerical studies have been carried out using a
validated two-dimensional standard k-omega turbulence model for
the design optimization of a thrust vector control system using shock
induced self-impinging supersonic secondary double jet. Parametric
analytical studies have been carried out at different secondary
injection locations to identifying the highest unsymmetrical
distribution of the main gas flow due to shock waves, which produces
a desirable side force more lucratively for vectoring. The results from
the parametric studies of the case on hand reveal that the shock
induced self-impinging supersonic secondary double jet is more
efficient in certain locations at the divergent region of a CD nozzle
than a case with supersonic single jet with same mass flow rate. We
observed that the best axial location of the self-impinging supersonic
secondary double jet nozzle with a given jet interaction angle, built-in
to a CD nozzle having area ratio 1.797, is 0.991 times the primary
nozzle throat diameter from the throat location. We also observed
that the flexible steering is possible after invoking ON/OFF facility to
the secondary nozzles for meeting the onboard mission requirements.
Through our case studies we concluded that the supersonic self-impinging
secondary double jet at predesigned jet interaction angle
and location can provide more flexible steering options facilitating
with 8.81% higher thrust vectoring efficiency than the conventional
supersonic single secondary jet without compromising the payload
capability of any supersonic aerospace vehicle.
Abstract: This paper investigates the connotation, and some of
the realistic implications, of the economic reform of health sector in
under developed countries. The paper investigates the issues that
economic reforms have to address, and the policy targets they are
considered to accomplish. The work argues that the development of
economic reform is not connected only with understanding the
priorities and refining them, furthermore with reformation and
restructuring the organizations through which health policies are
employed. Considering various organizational values, that are likely
to be regular to all economic reform programs, a regulatory approach
to institutional reform is unsuitable. The paper further investigates the
selection of economic reform that may as well influence via technical
suggestions and analysis, but the verdict to continue, and the
consequent success of execution, eventually depends on the
progressive political sustainability. The paper concludes by giving
examples of institutional reforms from various underdeveloped
countries and includes recommendation of the responsibility and
control of donor organizations.
Abstract: Background subtraction and temporal difference are
often used for moving object detection in video. Both approaches are
computationally simple and easy to be deployed in real-time image
processing. However, while the background subtraction is highly
sensitive to dynamic background and illumination changes, the
temporal difference approach is poor at extracting relevant pixels of
the moving object and at detecting the stopped or slowly moving
objects in the scene. In this paper, we propose a simple moving object
detection scheme based on adaptive background subtraction and
temporal difference exploiting dynamic background updates. The
proposed technique consists of histogram equalization, a linear
combination of background and temporal difference, followed by the
novel frame-based and pixel-based background updating techniques.
Finally, morphological operations are applied to the output images.
Experimental results show that the proposed algorithm can solve the
drawbacks of both background subtraction and temporal difference
methods and can provide better performance than that of each method.
Abstract: In recent decades, particulate matter (PM10) have
received much attention due to its potential adverse health impact and
the subsequent need to better control or regulate these pollutants.
The aim of this paper is focused on study risk assessment of PM10
in four different districts (Shebikah, Masfalah, Aziziyah, Awali) in
Makkah, Saudi Arabia during the period from 1 Ramadan 1434 AH -
27 Safar 1435 AH. Samples were collected by using Low Volume
Sampler (LVS Low Volume Sampler) device and filtration method
for estimating the total concentration of PM10.
The study indicated that the mean PM10 concentrations were 254.6
(186.1 - 343.2) μg/m3 in Shebikah, 184.9 (145.6 - 271.4) μg/m3 in
Masfalah, 162.4 (92.4-253.8) μg/m3 in Aziziyah, and 56.0 (44.5 -
119.8) μg/m3 in Awali. These values did not exceed the permissible
limits in PME (340 μg/m3 as daily average). Furthermore, health
assessment is carried out using AirQ2.2.3 model to estimate the
number of hospital admissions due to respiratory diseases. The
cumulative number of cases per 100,000 were 1534 (18-3050 case),
which lower than that recorded in the United States, Malaysia. The
concentration response coefficient was 0.49 (95% CI 0.05 - 0.70) per
10 μg/m3 increase of PM10.
Abstract: The purpose of this paper is to present a modeling and
control of a quarter-car active suspension system with unknown
mass, unknown time-delay and road disturbance. The objective of
designing the controller is to derive a control law to achieve stability
of the system and convergence that can considerably improve ride
comfort and road disturbance handling. This is accomplished by
using Routh-Hurwitz criterion based on defined parameters.
Mathematical proof is given to show the ability of the designed
controller to ensure the target of design, implementation with the
active suspension system and enhancement dispersion oscillation of
the system despite these problems. Simulations were also performed
to control quarter car suspension, where the results obtained from
these simulations verify the validity of the proposed design.
Abstract: Contemporary theories of sustainability, concerning
the natural and built environment, have recently introduced an
environmental attitude towards the architectural design that, in turn,
affects the practice of conservation and reuse of the existing building
stock. This paper presents an environmentally friendly approach
towards the conservation of vernacular architecture and it is based on
the results of a research program which involved the investigation of
sustainable design elements of traditional buildings in Cyprus. The
research in question showed that Cypriot vernacular architecture gave
more emphasis on cooling rather than heating strategies. Another
notable finding of the investigation was the great importance given to
courtyards as they enhance considerably, and in various ways, the
microclimatic conditions of the immediate environment with
favorable results throughout the year. Moreover, it was shown that
the reduction in temperature fluctuation observed in the closed and
semi-open spaces, compared to the respective temperature fluctuation
of the external environment -due to the thermal inertia of the building
envelope- helps towards the achievement of more comfortable living
conditions within traditional dwellings. This paper concludes with a
proposal of a sustainable approach towards the conservation of the
existing environment and the introduction of new environmental
criteria for the conservation of traditional buildings, beyond the
aesthetic, morphological and structural ones that are generally
applied.
Abstract: In light of the technological development and its
introduction into the field of education, an online course was
designed in parallel to the 'conventional' course for teaching the
''Qualitative Research Methods''. This course aimed to characterize
learning-teaching processes in a 'Qualitative Research Methods'
course studied in two different frameworks. Moreover, its objective
was to explore the difference between the culture of a physical
learning environment and that of online learning. The research
monitored four learner groups, a total of 72 students, for two years,
two groups from the two course frameworks each year. The courses
were obligatory for M.Ed. students at an academic college of
education and were given by one female-lecturer. The research was
conducted in the qualitative method as a case study in order to attain
insights about occurrences in the actual contexts and sites in which
they transpire. The research tools were open-ended questionnaire and
reflections in the form of vignettes (meaningful short pictures) to all
students as well as an interview with the lecturer. The tools facilitated
not only triangulation but also collecting data consisting of voices
and pictures of teaching and learning. The most prominent findings
are: differences between the two courses in the change features of the
learning environment culture for the acquisition of contents and
qualitative research tools. They were manifested by teaching
methods, illustration aids, lecturer's profile and students' profile.