Abstract: Early pre-code reinforced concrete structures present
undetermined resistance to earthquakes. This situation is particularly
unacceptable in the case of essential structures, such as healthcare
structures and pilgrims' houses. Amongst these, an existing old RC
building in Madinah city (KSA) is seismically evaluated with and
without infill wall and their dynamic characteristics are compared
with measured values in the field using ambient vibration
measurements (AVM). After updating the mathematical models for
this building with the experimental results, three dimensional
pushover analysis (Nonlinear static analysis) was carried out using
commercial structural analysis software incorporating inelastic
material properties for concrete, infill and steel. The purpose of this
analysis is to evaluate the expected performance of structural systems
by estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results summarized and discussed.
Abstract: In this paper, the transient device performance analysis
of n-type Gate Inside JunctionLess Transistor (GI-JLT) has been
evaluated. 3-D Bohm Quantum Potential (BQP) transport device
simulation has been used to evaluate the delay and power dissipation
performance. GI-JLT has a number of desirable device parameters
such as reduced propagation delay, dynamic power dissipation,
power and delay product, intrinsic gate delay and energy delay
product as compared to Gate-all-around transistors GAA-JLT. In
addition to this, various other device performance parameters namely,
on/off current ratio, short channel effects (SCE), transconductance
Generation Factor (TGF) and unity gain cut-off frequency (fT ) and
subthreshold slope (SS) of the GI-JLT and GAA-JLT have been
analyzed and compared. GI-JLT shows better device performance
characteristics than GAA-JLT for low power and high frequency
applications, because of its larger gate electrostatic control on the
device operation.
Abstract: Wireless mesh networking is rapidly gaining in
popularity with a variety of users: from municipalities to enterprises,
from telecom service providers to public safety and military
organizations. This increasing popularity is based on two basic facts:
ease of deployment and increase in network capacity expressed in
bandwidth per footage; WMNs do not rely on any fixed
infrastructure. Many efforts have been used to maximizing
throughput of the network in a multi-channel multi-radio wireless
mesh network. Current approaches are purely based on either static or
dynamic channel allocation approaches. In this paper, we use a
hybrid multichannel multi radio wireless mesh networking
architecture, where static and dynamic interfaces are built in the
nodes. Dynamic Adaptive Channel Allocation protocol (DACA), it
considers optimization for both throughput and delay in the channel
allocation. The assignment of the channel has been allocated to be codependent
with the routing problem in the wireless mesh network and
that should be based on passage flow on every link. Temporal and
spatial relationship rises to re compute the channel assignment every
time when the pattern changes in mesh network, channel assignment
algorithms assign channels in network. In this paper a computing
path which captures the available path bandwidth is the proposed
information and the proficient routing protocol based on the new path
which provides both static and dynamic links. The consistency
property guarantees that each node makes an appropriate packet
forwarding decision and balancing the control usage of the network,
so that a data packet will traverse through the right path.
Abstract: Alkylated silicon nanocrystals (C11-SiNCs) were
prepared successfully by galvanostatic etching of p-Si(100) wafers
followed by a thermal hydrosilation reaction of 1-undecene in
refluxing toluene in order to extract C11-SiNCs from porous silicon.
Erbium trichloride was added to alkylated SiNCs using a simple
mixing chemical route. To the best of our knowledge, this is the first
investigation on mixing SiNCs with erbium ions (III) by this
chemical method. The chemical characterization of C11-SiNCs and
their mixtures with Er3+(Er/C11-SiNCs) were carried out using X-ray
photoemission spectroscopy (XPS). The optical properties of C11-
SiNCs and their mixtures with Er3+ were investigated using Raman
spectroscopy and photoluminescence (PL). The erbium mixed
alkylated SiNCs shows an orange PL emission peak at around 595
nm that originates from radiative recombination of Si. Er/C11-SiNCs
mixture also exhibits a weak PL emission peak at 1536 nm that
originates from the intra-4f transition in erbium ions (Er3+). The PL
peak of Si in Er/C11-SiNCs mixture is increased in the intensity up to
three times as compared to pure C11-SiNCs. The collected data
suggest that this chemical mixing route leads instead to a transfer of
energy from erbium ions to alkylated SiNCs.
Abstract: Water spray cooling is a technique typically used in
heat treatment and other metallurgical processes where controlled
temperature regimes are required. Water spray cooling is used in
static (without movement) or dynamic (with movement of the steel
plate) regimes. The static regime is notable for the fixed position of
the hot steel plate and fixed spray nozzle. This regime is typical for
quenching systems focused on heat treatment of the steel plate. The
second application of spray cooling is the dynamic regime. The
dynamic regime is notable for its static section cooling system and
moving steel plate. This regime is used in rolling and finishing mills.
The fixed position of cooling sections with nozzles and the
movement of the steel plate produce nonhomogeneous water
distribution on the steel plate. The length of cooling sections and
placement of water nozzles in combination with the nonhomogeneity
of water distribution lead to discontinued or interrupted cooling
conditions. The impact of static and dynamic regimes on cooling
intensity and the heat transfer coefficient during the cooling process
of steel plates is an important issue.
Heat treatment of steel is accompanied by oxide scale growth. The
oxide scale layers can significantly modify the cooling properties and
intensity during the cooling. The combination of static and dynamic
(section) regimes with the variable thickness of the oxide scale layer
on the steel surface impact the final cooling intensity. The study of
the influence of the oxide scale layers with different cooling regimes
was carried out using experimental measurements and numerical
analysis. The experimental measurements compared both types of
cooling regimes and the cooling of scale-free surfaces and oxidized
surfaces. A numerical analysis was prepared to simulate the cooling
process with different conditions of the section and samples with
different oxide scale layers.
Abstract: Carbon fiber reinforced polymersarewidely used to strengthen steel structural elements. These structural elements are normally subjected to static, dynamic and fatigue loadings during their life-time. CFRP laminate is commonly used to strengthen these structures under the subjected loads. A number of studies have focused on the characteristics of CFRP sheets bonded to steel members under static, dynamic and fatigue loadings. However, there is a gap in understanding the bonding behavior between CFRP laminates and steel members under impact loading. This paper shows the effect of high load rates on this bond. CFRP laminate CFK 150/2000 was used to strengthen steel joints using Araldite 420 epoxy. The results show that applying a high load rate significantly affects the bond strength but has little influence on the effective bond length.
Abstract: Axial flow fans, while incapable of developing high
pressures, they are well suitable for handling large volumes of air at
relatively low pressures. In general, they are low in cost and possess
good efficiency, and can have blades of airfoil shape. Axial flow fans
show good efficiencies, and can operate at high static pressures if
such operation is necessary. Our objective is to model and analyze
the flow through AXIAL FANS using CFD Software and draw
inference from the obtained results, so as to get maximum efficiency.
The performance of an axial fan was simulated using CFD and the
effect of variation of different parameters such as the blade number,
noise level, velocity, temperature and pressure distribution on the
blade surface was studied. This paper aims to present a final 3D CAD
model of axial flow fan. Adapting this model to the available
components in the market, the first optimization was done. After this
step, CFX flow solver is used to do the necessary numerical analyses
on the aerodynamic performance of this model. This analysis results
in a final optimization of the proposed 3D model which is presented
in this article.
Abstract: Several of the practical industrial control processes are
multivariable processes. Due to the relation amid the variables
(interaction), delay in the loops, it is very intricate to design a
controller directly for these processes. So first, the interaction of the
variables is analyzed using Relative Normalized Gain Array
(RNGA), which considers the time constant, static gain and delay
time of the processes. Based on the effect of RNGA, relative gain
array (RGA) and NI, the pair (control configuration) of variables to
be controlled by decentralized control is selected. The equivalent
transfer function (ETF) of the process model is estimated as first
order process with delay using the corresponding elements in the
Relative gain array and Relative average residence time array
(RARTA) of the processes. Secondly, a decentralized Proportional-
Integral (PI) controller is designed for each ETF simply using
frequency response specifications. Finally, the performance and
robustness of the algorithm is comparing with existing related
approaches to validate the effectiveness of the projected algorithm.
Abstract: Today’s modern interconnected power system is
highly complex in nature. In this, one of the most important
requirements during the operation of the electric power system is the
reliability and security. Power and frequency oscillation damping
mechanism improve the reliability. Because of power system
stabilizer (PSS) low speed response against of major fault such as
three phase short circuit, FACTs devise that can control the network
condition in very fast time, are becoming popular. But FACTs
capability can be seen in a major fault present when nonlinear models
of FACTs devise and power system equipment are applied. To realize
this aim, the model of multi-machine power system with FACTs
controller is developed in MATLAB/SIMULINK using Sim Power
System (SPS) blockiest. Among the FACTs device, Static
synchronous series compensator (SSSC) due to high speed changes
its reactance characteristic inductive to capacitive, is effective power
flow controller. Tuning process of controller parameter can be
performed using different method. But Genetic Algorithm (GA)
ability tends to use it in controller parameter tuning process. In this
paper firstly POD controller is used to power oscillation damping.
But in this station, frequency oscillation dos not has proper damping
situation. So FOD controller that is tuned using GA is using that
cause to damp out frequency oscillation properly and power
oscillation damping has suitable situation.
Abstract: A cleaner production project was implemented in a
bakery. The project is based on the substitution of the best available
technique for an obsolete leaven production technology. The new
technology enables production of durable, high-quality leavens.
Moreover, 25% of flour as the original raw material can be replaced
by pastry from the previous day production which has not been sold.
That pastry was previously disposed in a waste incineration plant.
Besides the environmental benefits resulting from less waste, lower
consumption of energy, reduction of sewage waters quantity and
floury dustiness there are also significant economic benefits. Payback
period of investment was calculated with help of static method of
financial analysis about 2.6 years, using dynamic method 3.5 years
and an internal rate of return more than 29%. The supposed annual
average profit after taxationin the second year of operation was
incompliance with the real profit.
Abstract: Precast residential houses are normally constructed in Malaysia using precast shear-key wall panel and this panel is designed using BS8110 where there is no provision for earthquake. However, the safety of this house under moderate and strong earthquake is still questionable. Consequently, the full-scale of residential house are designed, constructed, tested and analyzed under in-plane lateral quasi-static cyclic loading. Hysteresis loops are plotted based on the experimental work and compared with modeling of hysteresis loops using HYSTERES in RUAUMOKO 2D program. Modified Takeda hysteresis model is chosen to behave a similar pattern with experimental work. This program will display the earthquake excitations, spectral displacements, pseudo spectral acceleration, mode shape and deformation of the structure. It can be concluded that this building is suffering severe cracks and damage under moderate and severe earthquake.
Abstract: In this paper an isolated wind-diesel hybrid power
system has been considered for reactive power control study having
an induction generator for wind power conversion and synchronous
alternator with automatic voltage regulator (AVR) for diesel unit is
presented. The dynamic voltage stability evaluation is dependent on
small signal analysis considering a Static VAR Compensator (SVC)
and IEEE type -I excitation system. It's shown that the variable
reactive power source like SVC is crucial to meet the varying
demand of reactive power by induction generator and load and to
acquire an excellent voltage regulation of the system with minimum
fluctuations. Integral square error (ISE) criterion can be used to
evaluate the optimum setting of gain parameters. Finally the dynamic
responses of the power systems considered with optimum gain setting
will also be presented.
Abstract: In this paper a novel design of aerostatic thrust bearing
is proposed and is analyzed numerically. The capillary restrictor and
bearing disk are made of elastomer like silicone and PU. The
viscoelasticity of elastomer helps the capillary expand for more air
flux and at the same time, allows conicity of the bearing surface to
form when the air pressure is enhanced. Therefore the bearing has the
better ability of passive compensation. In the present example, as
compared with the typical model, the new designs can nearly double
the load capability and offer four times static stiffness.
Abstract: This paper contains 2 main parts. In the first part of paper we simulated and studied three types of electrode patterns used in various industries for suspension and handling of the semiconductor and glass and we selected the best pattern by evaluating the electrostatic force, which was comb pattern electrode.
In the second part we investigated the parameters affecting the amount of electrostatic force such as the gap between surface and electrode (g), the electrode width (w), the gap between electrodes (t), the surface permittivity and electrode length and methods of improvement of adhesion force by changing these values.
Abstract: Bone properties and response behavior after static or
dynamic activation (loading) are still interesting topics in many fields
of the science especially in the biomechanical problems such as bone
loss of astronauts in space, osteoporosis, bone remodeling after
fracture or remodeling after surgery (endoprosthesis and implants)
and in osteointegration. This contribution deals with the relation
between physiological, demineralized and deproteinized state of the
turkey long bone – tibia. Three methods for comparison were used: 1)
densitometry, 2) three point bending and 3) frequency analysis. The
main goal of this work was to describe the decrease of the protein
(collagen) or mineral of the bone with relation to the fracture in three
point bending. The comparison is linked to the problem of different
bone mechanical behavior in physiological and osteoporotic state.
Abstract: Metallic foams have good potential for lightweight
structures for impact and blast mitigation. Therefore it is important to
find out the optimized foam structure (i.e. cell size, shape, relative
density, and distribution) to maximise energy absorption. In this
paper, quasistatic compression and microstructural characterization
of closed-cell aluminium foams of different pore size and cell
distributions have been carried out. We present results for two
different aluminium metal foams of density 0.49-0.51 g/cc and 0.31-
0.34 g/cc respectively that have been tested in quasi-static
compression. The influence of cell geometry and cell topology on
quasistatic compression behaviour has been investigated using optical
microscope and computed tomography (micro-CT) analysis. It is
shown that the deformation is not uniform in the structure and
collapse begins at the weakest point.
Abstract: Due to reduced stiffness, research on second
generation titanium alloys for implant applications, like the
metastable β-titanium alloy Ti-15Mo, become more and more
important in the recent years. The machinability of these alloys is
generally poor leading to problems during implant production and
comparably large production costs. Therefore, in the present study,
Ti-15Mo was alloyed with 0.8 wt.-% of the rare earth metals
lanthanum (Ti-15Mo+0.8La) and neodymium (Ti-15Mo+0.8Nd) to
improve its machinability. Their microstructure consisted of a
titanium matrix and micrometer-size particles of the rare earth metals
and two of their oxides. The particles stabilized the microstructure as
grain growth was minimized. As especially the ductility might be
affected by the precipitates, the behavior of Ti-15Mo+0.8La and Ti-
15Mo+0.8Nd was investigated during static and dynamic
deformation at elevated temperature to develop a processing route.
The resulting mechanical properties (static strength and ductility)
were similar in all investigated alloys.
Abstract: This paper presents general results on the Java source
code snippet detection problem. We propose the tool which uses
graph and subgraph isomorphism detection. A number of solutions
for all of these tasks have been proposed in the literature. However,
although that all these solutions are really fast, they compare just the
constant static trees. Our solution offers to enter an input sample
dynamically with the Scripthon language while preserving an
acceptable speed. We used several optimizations to achieve very low
number of comparisons during the matching algorithm.
Abstract: Access control is one of the most challenging issues
facing information security. Access control is defined as, the ability to
permit or deny access to a particular computational resource or digital
information by an unauthorized user or subject. The concept of usage
control (UCON) has been introduced as a unified approach to capture a
number of extensions for access control models and systems. In
UCON, an access decision is determined by three factors:
authorizations, obligations and conditions. Attribute mutability and
decision continuity are two distinct characteristics introduced by
UCON for the first time. An observation of UCON components
indicates that, the components are predefined and static. In this paper,
we propose a new and flexible model of usage control for the creation
and elimination of some of these components; for example new
objects, subjects, attributes and integrate these with the original
UCON model. We also propose a model for concurrent usage
scenarios in UCON.
Abstract: The aim of this work is to present a theoretical analysis of a 2D ultrasound transducer comprised of crossed arrays of metal strips placed on both sides of thin piezoelectric layer (a). Such a structure is capable of electronic beam-steering of generated wavebeam both in elevation and azimuth. In this paper a semi-analytical model of the considered transducer is developed. It is based on generalization of the well-known BIS-expansion method. Specifically, applying the electrostatic approximation, the electric field components on the surface of the layer are expanded into fast converging series of double periodic spatial harmonics with corresponding amplitudes represented by the properly chosen Legendre polynomials. The problem is reduced to numerical solving of certain system of linear equations for unknown expansion coefficients.