Abstract: A field experiment was carried out at Arab El-
Awammer Research Station, Agric. Res. Center. Assiut Governorate
during summer seasons of 2013 and 2014. The present study assessed
the effect of cowpea with maize intercropping on yield and its
components. The experiment comprised of three treatments (sole
cowpea, sole maize and cowpea-maize intercrop). The experimental
design was a randomized complete block with four replications.
Results indicated that intercropped maize plants with cowpea,
exhibited greater potentiality and resulted in higher values of most of
the studied criteria viz., plant height, number of ears/plant, number of
rows/ear, number of grains/row, grains weight/ear, 100–grain weight
and straw and grain yields. Fresh and dry forage yields of cowpea
were lower in intercropping with maize than sole. Furthermore, the
combined of the two seasons revealed that the total Land Equivalent
Ratio (LER) between cowpea and maize was 1.65. The Aggressivity
(A) maize was 0.45 and cowpea was -0.45. This showed that maize
was the dominant crop, whereas cowpea was the dominated. The
Competitive Ratio (CR) indicated that maize more competitive than
cowpea, maize was 1.75 and cowpea was 0.57. The Actual Yield
Loss (AYL) maize was 0.05 and cowpea was -0.40. The Monetary
Advantage Index (MAI) was 2360.80.
Abstract: Endowed of renewable energy sources (RES) are the
advantages of ASEAN, but they are using a low amount of RES only
to generate electricity because their primary energy sources are fossil
and coal. The cost of purchasing fossil and coal is cheaper now, but it
might be expensive soon, as it will be depleted sooner and after.
ASEAN showed that the RES are convenient to be implemented.
Some country in ASEAN has huge renewable energy sources
potential and use. The primary aim of this project is to assist ASEAN
countries in preparing the renewable energy and to guide the policies
for RES in the more upright direction. The Green-Y model will help
ASEAN government to study and forecast the economic concept,
including feed-in tariff.
Abstract: Securing the confidential data transferred via wireless
network remains a challenging problem. It is paramount to ensure
that data are accessible only by the legitimate users rather than by the
attackers. One of the most serious threats to organization is jamming,
which disrupts the communication between any two pairs of nodes.
Therefore, designing an attack-defending scheme without any packet
loss in data transmission is an important challenge. In this paper,
Dependence based Malicious Route Defending DMRD Scheme has
been proposed in multi path routing environment to prevent jamming
attack. The key idea is to defend the malicious route to ensure
perspicuous transmission. This scheme develops a two layered
architecture and it operates in two different steps. In the first step,
possible routes are captured and their agent dependence values are
marked using triple agents. In the second step, the dependence values
are compared by performing comparator filtering to detect malicious
route as well as to identify a reliable route for secured data
transmission. By simulation studies, it is observed that the proposed
scheme significantly identifies malicious route by attaining lower
delay time and route discovery time; it also achieves higher
throughput.
Abstract: In this research, waterglass based aerogel powder was
prepared by sol–gel process and ambient pressure drying. Inspired by
limited dust releasing, aerogel powder was introduced to the PET
electrospinning solution in an attempt to create required bulk and
surface structure for the nanofibers to improve their hydrophobic and
insulation properties. The samples evaluation was carried out by
measuring density, porosity, contact angle, heat transfer, FTIR, BET,
and SEM. According to the results, porous silica aerogel powder was
fabricated with mean pore diameter of 24 nm and contact angle of
145.9º. The results indicated the usefulness of the aerogel powder
confined into nanofibers to control surface roughness for
manipulating superhydrophobic nanowebs with water contact angle
of 147º. It can be due to a multi-scale surface roughness which was
created by nanowebs structure itself and nanofibers surface
irregularity in presence of the aerogels while a layer of fluorocarbon
created low surface energy. The wettability of a solid substrate is an
important property that is controlled by both the chemical
composition and geometry of the surface. Also, a decreasing trend in
the heat transfer was observed from 22% for the nanofibers without
any aerogel powder to 8% for the nanofibers with 4% aerogel
powder. The development of thermal insulating materials has become
increasingly more important than ever in view of the fossil energy
depletion and global warming that call for more demanding energysaving
practices.
Abstract: The focal aspire of e-Government (eGovt) is to offer
citizen-centered service delivery. Accordingly, the citizenry
consumes services from multiple government agencies through
national portal. Thus, eGovt is an enterprise with the primary
business motive of transparent, efficient and effective public services
to its citizenry and its logical structure is the eGovernment Enterprise
Architecture (eGEA). Since eGovt is IT oriented multifaceted
service-centric system, EA doesn’t do much on an automated
enterprise other than the business artifacts. Service-Oriented
Architecture (SOA) manifestation led some governments to pertain
this in their eGovts, but it limits the source of business artifacts. The
concurrent use of EA and SOA in eGovt executes interoperability and
integration and leads to Service-Oriented e-Government Enterprise
(SOeGE). Consequently, agile eGovt system becomes a reality. As an
IT perspective eGovt comprises of centralized public service artifacts
with the existing application logics belong to various departments at
central, state and local level. The eGovt is renovating to SOeGE by
apply the Service-Orientation (SO) principles in the entire system.
This paper explores IT perspective of SOeGE in India which
encompasses the public service models and illustrated with a case
study the Passport service of India.
Abstract: Cloud computing has provided the impetus for change
in the demand, sourcing, and consumption of IT-enabled services.
The technology developed from an emerging trend towards a ‘musthave’.
Many organizations harnessed on the quick-wins of cloud
computing within the last five years but nowadays reach a plateau
when it comes to sustainable savings and performance. This study
aims to investigate what is needed from an organizational perspective
to make cloud computing a sustainable success. The study was
carried out in Germany among senior IT professionals, both in
management and delivery positions. Our research shows that IT
executives must be prepared to realign their IT workforce to sustain
the advantage of cloud computing for today and the near future.
While new roles will undoubtedly emerge, roles alone cannot ensure
the success of cloud deployments. What is needed is a change in the
IT workforce’s business behaviour, or put more simply, the ways in
which the IT personnel works. It gives clear guidance on which
dimensions of an employees’ working behaviour need to be adapted.
The practical implications are drawn from a series of semi-structured
interviews, resulting in a high-level workforce enablement plan.
Lastly, it elaborates on tools and gives clear guidance on which
pitfalls might arise along the proposed workforce enablement
process.
Abstract: Software Architecture is the basic structure of
software that states the development and advancement of a software
system. Software architecture is also considered as a significant tool
for the construction of high quality software systems. A clean design
leads to the control, value and beauty of software resulting in its
longer life while a bad design is the cause of architectural erosion
where a software evolution completely fails. This paper discusses the
occurrence of software architecture erosion and presents a set of
methods for the detection, declaration and prevention of architecture
erosion. The causes and symptoms of architecture erosion are
observed with the examples of prescriptive and descriptive
architectures and the practices used to stop this erosion are also
discussed by considering different types of software erosion and their
affects. Consequently finding and devising the most suitable
approach for fighting software architecture erosion and in some way
reducing its affect is evaluated and tested on different scenarios.
Abstract: The paper describes a Chinese shadow play animation
system based on Kinect. Users, without any professional training, can
personally manipulate the shadow characters to finish a shadow play
performance by their body actions and get a shadow play video
through giving the record command to our system if they want. In our
system, Kinect is responsible for capturing human movement and
voice commands data. Gesture recognition module is used to control
the change of the shadow play scenes. After packaging the data from
Kinect and the recognition result from gesture recognition module,
VRPN transmits them to the server-side. At last, the server-side uses
the information to control the motion of shadow characters and video
recording. This system not only achieves human-computer interaction,
but also realizes the interaction between people. It brings an
entertaining experience to users and easy to operate for all ages. Even
more important is that the application background of Chinese shadow
play embodies the protection of the art of shadow play animation.
Abstract: Logistics distributors face the issue of having to
provide increasing service levels while being forced to reduce costs at
the same time. Same-day delivery, quick order processing and rapidly
growing ranges of articles are only some of the prevailing challenges.
One key aspect of the performance of an intra-logistics system is how
often and in which amplitude congestions and dysfunctions affect the
processing operations. By gaining knowledge of the so called
‘performance availability’ of such a system during the planning stage,
oversizing and wasting can be reduced whereas planning
transparency is increased. State of the art for the determination of this
KPI is simulation studies. However, their structure and therefore their
results may vary unforeseeably. This article proposes a concept for
the establishment of ‘certified’ and hence reliable and comparable
simulation models.
Abstract: This work was one of the tasks of the
Manufacturing2Client project, whose objective was to develop a
frontal deflector to be commercialized in the automotive industry,
using new project and manufacturing methods. In this task, in
particular, it was proposed to develop the ability to predict
computationally the aerodynamic influence of flow in vehicles, in an
effort to reduce fuel consumption in vehicles from class 3 to 8. With
this aim, two deflector models were developed and their aerodynamic
performance analyzed. The aerodynamic study was done using the
Computational Fluid Dynamics (CFD) software Ansys CFX and
allowed the calculation of the drag coefficient caused by the vehicle
motion for the different configurations considered. Moreover, the
reduction of diesel consumption and carbon dioxide (CO2) emissions
associated with the optimized deflector geometry could be assessed.
Abstract: The final step to complete the “Analytical Systems
Engineering Process” is the “Allocated Architecture” in which all
Functional Requirements (FRs) of an engineering system must be
allocated into their corresponding Physical Components (PCs). At
this step, any design for developing the system’s allocated
architecture in which no clear pattern of assigning the exclusive
“responsibility” of each PC for fulfilling the allocated FR(s) can be
found is considered a poor design that may cause difficulties in
determining the specific PC(s) which has (have) failed to satisfy a
given FR successfully. The present study utilizes the Axiomatic
Design method principles to mathematically address this problem and
establishes an “Axiomatic Model” as a solution for reaching good
alternatives for developing the allocated architecture. This study
proposes a “loss Function”, as a quantitative criterion to monetarily
compare non-ideal designs for developing the allocated architecture
and choose the one which imposes relatively lower cost to the
system’s stakeholders. For the case-study, we use the existing design
of U. S. electricity marketing subsystem, based on data provided by
the U.S. Energy Information Administration (EIA). The result for
2012 shows the symptoms of a poor design and ineffectiveness due to
coupling among the FRs of this subsystem.
Abstract: Machining parameters are very important in
determining the surface quality of any material. In the past decade,
some new engineering materials were developed for the
manufacturing industry which created a need to conduct an
investigation on the impact of the said parameters on their surface
roughness. Polyurethane (PU) block is widely used in the automotive
industry to manufacture parts such as checking fixtures that are used
to verify the dimensional accuracy of automotive parts. In this paper,
the design of experiment (DOE) was used to investigate on the effect
of the milling parameters on the PU block. Furthermore, an analysis
of the machined surface chemical composition was done using
scanning electron microscope (SEM). It was found that the surface
roughness of the PU block is severely affected when PU undergoes a
flood machining process instead of a dry condition. In addition the
stepover and the silicon content were found to be the most significant
parameters that influence the surface quality of the PU block.
Abstract: Rhodamine B (RB) is a toxic dye used extensively in
textile industry, which must be remediated before its drainage to
environment. In the present study, supported gold nanoparticles on
commercially available titania and zincite were successfully prepared
and then their activity on the photodegradation of RB under UV A
light irradiation were evaluated. The synthesized photocatalysts were
characterized by ICP, BET, XRD, and TEM. Kinetic results showed
that Au/TiO2 was an inferior photocatalyst to Au/ZnO. This
observation could be attributed to the strong reflection of UV
irradiation by gold nanoparticles over TiO2 support.
Abstract: Safety is one of the most important considerations
when buying a new car. While active safety aims at avoiding
accidents, passive safety systems such as airbags and seat belts
protect the occupant in case of an accident. In addition to legal
regulations, organizations like Euro NCAP provide consumers with
an independent assessment of the safety performance of cars and
drive the development of safety systems in automobile industry.
Those ratings are mainly based on injury assessment reference values
derived from physical parameters measured in dummies during a car
crash test.
The components and sub-systems of a safety system are designed
to achieve the required restraint performance. Sled tests and other
types of tests are then carried out by car makers and their suppliers
to confirm the protection level of the safety system. A Knowledge
Discovery in Databases (KDD) process is proposed in order to
minimize the number of tests. The KDD process is based on the
data emerging from sled tests according to Euro NCAP specifications.
About 30 parameters of the passive safety systems from different data
sources (crash data, dummy protocol) are first analysed together with
experts opinions. A procedure is proposed to manage missing data
and validated on real data sets. Finally, a procedure is developed to
estimate a set of rough initial parameters of the passive system before
testing aiming at reducing the number of tests.
Abstract: Bamboo is extensively used in construction industry.
Low durability of bamboo due to fungus infestation and termites
attack under storage puts certain constrains for it usage as modern
structural material. Looking at many chemical formulations for
bamboo treatment leading to severe harmful environment effects,
research on eco-friendly preservatives for bamboo treatment has been
initiated world-over. In the present studies, eco-friendly preservative
for bamboo treatment has been developed. To validate its application
for structural purposes, investigation of effect of treatment on
compressive strength has been investigated. Neemoil (25%)
integrated with copper naphthenate (0.3%) on dilution with kerosene
oil impregnated into bamboo culm at 2 bar pressure, has shown
weight loss of only 3.15% in soil block analysis method. The results
from compressive strength analysis using HEICO Automatic
Compression Testing Machine reveal that preservative treatment has
not altered the structural properties of bamboo culms. Compressive
strength of control (11.72 N/mm2) and above treated samples (11.71
N/mm2) was found to be comparable.
Abstract: The classroom of the 21st century is an ever changing
forum for new and innovative thoughts and ideas. With increasing
technology and opportunity, students have rapid access to
information that only decades ago would have taken weeks to obtain.
Unfortunately, new techniques and technology are not the cure for
the fundamental problems that have plagued the classroom ever since
education was established. Class size has been an issue long debated
in academia. While it is difficult to pin point an exact number, it is
clear that in this case more does not mean better. By looking into the
success and pitfalls of classroom size the true advantages of smaller
classes will become clear. Previously, one class was comprised of 50
students. Being seventeen and eighteen- year- old students,
sometimes it was quite difficult for them to stay focused. To help
them understand and gain much knowledge, a researcher introduced
“The Theory of Multiple Intelligence” and this, in fact, enabled
students to learn according to their own learning preferences no
matter how they were being taught. In this lesson, the researcher
designed a cycle of learning activities involving all intelligences so
that everyone had equal opportunities to learn.
Abstract: Image spam is a kind of email spam where the spam
text is embedded with an image. It is a new spamming technique
being used by spammers to send their messages to bulk of internet
users. Spam email has become a big problem in the lives of internet
users, causing time consumption and economic losses. The main
objective of this paper is to detect the image spam by using histogram
properties of an image. Though there are many techniques to
automatically detect and avoid this problem, spammers employing
new tricks to bypass those techniques, as a result those techniques are
inefficient to detect the spam mails. In this paper we have proposed a
new method to detect the image spam. Here the image features are
extracted by using RGB histogram, HSV histogram and combination
of both RGB and HSV histogram. Based on the optimized image
feature set classification is done by using k- Nearest Neighbor(k-NN)
algorithm. Experimental result shows that our method has achieved
better accuracy. From the result it is known that combination of RGB
and HSV histogram with k-NN algorithm gives the best accuracy in
spam detection.
Abstract: Steganography is the art and science that hides the information in an appropriate cover carrier like image, text, audio and video media. In this work the authors propose a new image based steganographic method for hiding information within the complex bit planes of the image. After slicing into bit planes the cover image is analyzed to extract the most complex planes in decreasing order based on their bit plane complexity. The complexity function next determines the complex noisy blocks of the chosen bit plane and finally pixel mapping method (PMM) has been used to embed secret bits into those regions of the bit plane. The novel approach of using pixel mapping method (PMM) in bit plane domain adaptively embeds data on most complex regions of image, provides high embedding capacity, better imperceptibility and resistance to steganalysis attack.
Abstract: This study presents an attempt to evaluate the
antioxidant potential and antimicrobial activity of methanolic extract,
and essential oils prepared from the leaves of sage (Salvia officinalis
L.). The content of polyphenol in the methanolic extracts from the
leaves of Salvia officinalis was determined spectrophotometrically,
calculated as gallic acid and catechin equivalent. The essential oils
and methanol extract were also subjected to screenings for the
evaluation of their antioxidant activities using 2, 2-diphenyl-1-
picrylhydrazyl (DPPH) test. While the plant essential oils showed
only weak antioxidant activities, its methanol extract was
considerably active in DPPH (IC50 = 37.29 μg/ml) test. Appreciable
total polyphenol content (31.25 mg/g) was also detected for the plant
methanol extract as gallic acid equivalent in the Folin–Ciocalteu test.
The plant was also screened for its antimicrobial activity and good to
moderate inhibitions were recorded for its essential oils, and
methanol extracts against most of the tested microorganisms.
The present investigation revealed that this plant had rich source
of antioxidant properties. It is for this reason that sage has found
increasing application in food formulations.
Abstract: Heavy rare earth (HRE) oxalate concentrates were
prepared from the Egyptian crude monazite sand (graded about 47%).
The concentrates were specified quantitatively for their constituents
of individual rare earth elements using ion chromatograph (IC) and
qualitatively by scanning electron microscope (SEM) for the other
major constituents. The 1st concentrate was composed of 10.5%
HREE where 7.25% of them represented yttrium. The 2nd concentrate
contained about 41.7% LREE, 17.5% HREE and 13.6% Th. The
LREE involved 18.3% Ce, 10.5% La and 8% Nd while the HREE
were 8.7% Y, 3.5% Gd and 2.9% Dy. The 3rd concentrate was
containing about 8.0% LREE (3.7% Ce, 2.0% La and 1.5% Nd),
10.2% HREE (6.4% yttrium and 2.0% Dy) and 2.1% uranium. The
final concentrate comprised 0.84% uranium beside iron, chromium
and traces of REE.