Abstract: A hybrid quasi-steady thermal lattice Boltzmann model was used to study the combined effects of temperature and contact angle on the movement of slugs and droplets of oil in water (O/W) system flowing between two parallel plates. The model static contact angle due to the deposition of the O/W droplet on a flat surface with simulated hydrophilic characteristic at different fluid temperatures, matched very well the proposed theoretical calculation. Furthermore, the model was used to simulate the dynamic behavior of droplets and slugs deposited on the domain’s upper and lower surfaces, while subjected to parabolic flow conditions. The model accurately simulated the contact angle hysteresis for the dynamic droplets cases. It was also shown that at elevated temperatures the required power to transport the mixture diminished remarkably.
Abstract: Polypropylene (PP) is one of the most commonly used plastics because of its low density, outstanding mechanical properties, and low cost. However, its drawbacks such as low surface energy, poor dyeability, lack of chemical functionalities, and poor compatibility with polar polymers and inorganic materials, have restricted the application of PP. To expand its application in biomedical materials, functionalization is considered to be the most effective way. In this study, PP was functionalized with a chiral monomer, (S)-1-acryloylpyrrolidine-2-carboxylic acid ((S)-APCA), by free-radical grafting in the solid phase. The grafting degree of PP-g-APCA was determined by chemical titration method, and the chemical structure of functionalized PP was characterized by FTIR spectroscopy, which confirmed that the chiral monomer (S)-APCA was successfully grafted onto PP. Static water contact angle results suggested that the surface hydrophilicity of PP was significantly improved by solid phase grafting and assistance of surface water treatment. Protein adsorption and platelet adhesion results showed that hemocompatibility of PP was greatly improved by grafting the chiral monomer.
Abstract: Surface characteristics of Bacillus megaterium strain
were investigated; zeta potential, FTIR and contact angle were
measured. Surface energy components including Lifshitz-van der
Waals, Hamaker constant, and acid/base components (Lewis
acid/Lewis base) were calculated from the contact angle data. The
results showed that the microbial cells were negatively charged over
all pH regions with high values at alkaline region. A hydrophilic
nature for the strain was confirmed by contact angle and free energy
of adhesion between microbial cells. Adsorption affinity of the strain
toward dolomite was studied at different pH values. The results
showed that the cells had a high affinity to dolomite at acid pH
comparing to neutral and alkaline pH. Extended DLVO theory was
applied to calculate interaction energy between B. megaterium cells
and dolomite particles. The adsorption results were in agreement with
the results of Extended DLVO approach. Surface changes occurred
on dolomite surface after the bio-treatment were monitored; contact
angle decreased from 69° to 38° and the mineral’s floatability
decreased from 95% to 25% after the treatment.
Abstract: This paper discusses micrometeorological aspects of the urban climate in three cities in Western São Paulo State: Presidente Prudente, Assis and Iepê. Particular attention is paid to the method used to estimate the components of the energy balance at the surface. Estimates of convective fluxes showed that the Bowen ratio was an indicator of the local climate and that its magnitude varied between 0.3 and 0.7. Maximum values for the Bowen ratio occurred earlier in Iepê (11:00 am) than in Presidente Prudente (4:00 pm). The results indicate that the Bowen ratio is modulated by the radiation balance at the surface and by different clusters of vegetation.
Abstract: In this research, waterglass based aerogel powder was
prepared by sol–gel process and ambient pressure drying. Inspired by
limited dust releasing, aerogel powder was introduced to the PET
electrospinning solution in an attempt to create required bulk and
surface structure for the nanofibers to improve their hydrophobic and
insulation properties. The samples evaluation was carried out by
measuring density, porosity, contact angle, heat transfer, FTIR, BET,
and SEM. According to the results, porous silica aerogel powder was
fabricated with mean pore diameter of 24 nm and contact angle of
145.9º. The results indicated the usefulness of the aerogel powder
confined into nanofibers to control surface roughness for
manipulating superhydrophobic nanowebs with water contact angle
of 147º. It can be due to a multi-scale surface roughness which was
created by nanowebs structure itself and nanofibers surface
irregularity in presence of the aerogels while a layer of fluorocarbon
created low surface energy. The wettability of a solid substrate is an
important property that is controlled by both the chemical
composition and geometry of the surface. Also, a decreasing trend in
the heat transfer was observed from 22% for the nanofibers without
any aerogel powder to 8% for the nanofibers with 4% aerogel
powder. The development of thermal insulating materials has become
increasingly more important than ever in view of the fossil energy
depletion and global warming that call for more demanding energysaving
practices.
Abstract: Polymer-like organic thin films were deposited on both
aluminum alloy type 6061 and glass substrates at room temperature by
Plasma Enhanced Chemical Vapor Deposition (PECVD) methodusing
benzene and hexamethyldisiloxane (HMDSO) as precursor materials.
The surface and physical properties of plasma-polymerized organic
thin films were investigated at different r.f. powers. The effects of
benzene/argon ratio on the properties of plasma polymerized benzene
films were also investigated. It is found that using benzene alone
results in a non-coherent and non-adherent powdery deposited
material. The chemical structure and surface properties of the asgrown
plasma polymerized thin films were analyzed on glass
substrates with FTIR and contact angle measurements. FTIR spectra
of benzene deposited film indicated that the benzene rings are
preserved when increasing benzene ratio and/or decreasing r.f.
powers. FTIR spectra of HMDSO deposited films indicated an
increase of the hydrogen concentration and a decrease of the oxygen
concentration with the increase of r.f. power. The contact angle (θ) of
the films prepared from benzene was found to increase by about 43%
as benzene ratio increases from 10% to 20%. θ was then found to
decrease to the original value (51°) when the benzene ratio increases
to 100%. The contact angle, θ, for both benzene and HMDSO
deposited films were found to increase with r.f. power. This signifies
that the plasma polymerized organic films have substantially low
surface energy as the r.f power increases. The corrosion resistance of
aluminum alloy substrate both bare and covered with plasma
polymerized thin films was carried out by potentiodynamic
polarization measurements in standard 3.5 wt. % NaCl solution at
room temperature. The results indicate that the benzene and HMDSO
deposited films are suitable for protection of the aluminum substrate
against corrosion. The changes in the processing parameters seem to
have a strong influence on the film protective ability. Surface
roughness of films deposited on aluminum alloy substrate was
investigated using scanning electron microscopy (SEM). The SEM
images indicate that the surface roughness of benzene deposited films
increase with decreasing the benzene ratio. SEM images of benzene
and HMDSO deposited films indicate that the surface roughness
decreases with increasing r.f. power. Studying the above parameters
indicate that the films produced are suitable for specific practical
applications.
Abstract: When the characteristic length of an elastic solid is
down to the nanometer level, its deformation behavior becomes size
dependent. Surface energy /surface stress have recently been applied
to explain such dependency. In this paper, the effect of
strain-independent surface stress on the deformation of an isotropic
elastic solid containing a nanosized elliptical hole is studied by the
finite element method. Two loading cases are considered, in the first
case, hoop stress along the rim of the elliptical hole induced by pure
surface stress is studied, in the second case, hoop stress around the
elliptical opening under combined remote tension and surface stress is
investigated. It has been shown that positive surface stress induces
compressive hoop stress along the hole, and negative surface stress has
opposite effect, maximum hoop stress occurs near the major semi-axes
of the ellipse. Under combined loading of remote tension and surface
stress, stress concentration around the hole can be either intensified or
weakened depending on the sign of the surface stress.
Abstract: Nanowire arrays of copper with uniform diameters have
been synthesized by potentiostatic electrochemical metal deposition
(EMD) of copper sulphate and potassium chloride solution within
the nano-channels of porous Indium-Tin Oxide (ITO), also known as
Tin doped Indium Oxide templates. The nanowires developed were
fairly continuous with diameters ranging from 110-140 nm along
the entire length. Single as well as poly-crystalline copper wires
have been prepared by application of appropriate potential during the
EMD process. Scanning electron microscopy (SEM), high resolution
transmission electron microscopy (HRTEM), small angle electron
diffraction (SAED) and atomic force microscopy (AFM) were used
to characterize the synthesized nano wires at room temperature. The
electrochemical response of synthesized products was evaluated by
cyclic voltammetry while surface energy analysis was carried out
using a Goniometer.
Abstract: In the present study, the incorporation of graphene
into blends of acrylonitrile-butadiene-styrene terpolymer with
polypropylene (ABS/PP) was investigated focusing on the
improvement of their thermomechanical characteristics and the effect
on their rheological behavior. The blends were prepared by melt
mixing in a twin-screw extruder and were characterized by measuring
the MFI as well as by performing DSC, TGA and mechanical tests.
The addition of graphene to ABS/PP blends tends to increase their
melt viscosity, due to the confinement of polymer chains motion.
Also, graphene causes an increment of the crystallization temperature
(Tc), especially in blends with higher PP content, because of the
reduction of surface energy of PP nucleation, which is a consequence
of the attachment of PP chains to the surface of graphene through the
intermolecular CH-π interaction. Moreover, the above nanofiller
improves the thermal stability of PP and increases the residue of
thermal degradation at all the investigated compositions of blends,
due to the thermal isolation effect and the mass transport barrier
effect. Regarding the mechanical properties, the addition of graphene
improves the elastic modulus, because of its intrinsic mechanical
characteristics and its rigidity, and this effect is particularly strong in
the case of pure PP.
Abstract: Following the laser ablation studies leading to a
theory of nuclei confinement by a Debye layer mechanism, we
present here numerical evaluations for the known stable nuclei where
the Coulomb repulsion is included as a rather minor component
especially for lager nuclei. In this research paper the required
physical conditions for the formation and stability of nuclei
particularly endothermic nuclei with mass number greater than to
which is an open astrophysical question have been investigated.
Using the Debye layer mechanism, nuclear surface energy, Fermi
energy and coulomb repulsion energy it is possible to find conditions
under which the process of nucleation is permitted in early universe.
Our numerical calculations indicate that about 200 second after the
big bang at temperature of about 100 KeV and subrelativistic region
with nucleon density nearly equal to normal nuclear density namely,
10cm all endothermic and exothermic nuclei have been
formed.
Abstract: Iris localization is a very important approach in
biometric identification systems. Identification process usually is
implemented in three levels: iris localization, feature extraction, and
pattern matching finally. Accuracy of iris localization as the first step
affects all other levels and this shows the importance of iris
localization in an iris based biometric system. In this paper, we
consider Daugman iris localization method as a standard method,
propose a new method in this field and then analyze and compare the
results of them on a standard set of iris images. The proposed method
is based on the detection of circular edge of iris, and improved by
fuzzy circles and surface energy difference contexts. Implementation
of this method is so easy and compared to the other methods, have a
rather high accuracy and speed. Test results show that the accuracy of
our proposed method is about Daugman method and computation
speed of it is 10 times faster.