Abstract: Laser beam welding of dissimilar sheet metal
combinations such as Ti/Al, SS/Al and Cu/Al are increasingly
demanded due to high energy densities with less fusion and heat
affected zones. A good weld joint strength involves combinations of
dissimilar metals and the formation of solid solution in the weld pool.
Many metal pairs suffer from significant intermetallic phase
formation during welding which greatly reduces their strength. The
three different sheet metal mentioned above is critically reviewed and
phase diagram for the combinations are given. The aim of this study
is to develop an efficient metal combinations and the influence on
their interfacial characteristics. For that the following parameters
such as weld geometry, residual distortion, micro hardness,
microstructure and mechanical properties are analyzed
systematically.
Abstract: Early pre-code reinforced concrete structures present
undetermined resistance to earthquakes. This situation is particularly
unacceptable in the case of essential structures, such as healthcare
structures and pilgrims' houses. Amongst these, an existing old RC
building in Madinah city (KSA) is seismically evaluated with and
without infill wall and their dynamic characteristics are compared
with measured values in the field using ambient vibration
measurements (AVM). After updating the mathematical models for
this building with the experimental results, three dimensional
pushover analysis (Nonlinear static analysis) was carried out using
commercial structural analysis software incorporating inelastic
material properties for concrete, infill and steel. The purpose of this
analysis is to evaluate the expected performance of structural systems
by estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results summarized and discussed.
Abstract: Anthocyanins are natural pigments with effective UV
protection but their topical use could be limited due to their
physicochemical characteristics. An attempt to overcome such
limitations by complexation of 2 major anthocyanin-rich sources, C.
ternatea and Z. mays, has potentiated its use as topical antiinflammatory.
Cell studies indicate no cytotoxicity of the
anthocyanin complex (AC) up to 1 mg/ml tested in HaCaT and
human fore head fibroblasts by MTT. Croton oil-induced ear edema
in Wistar rats suggests an effective dose of 5 mg/cm2 of AC as a
topical anti-inflammatory in comparison to 0.5 mg/cm2 of
fluocinolone acetonide. Niosomal encapsulation of the AC
significantly prolonged the anti-inflammatory activity particularly at
8 h after topical application (p = 0.0001). The AC was not cytotoxic
and its anti-inflammatory and activity was dose-dependent and
prolonged by niosomal encapsulation. It has also shown to promote
collagen type 1 production in cell culture. Thus, AC could be a
potential candidate for topical anti-inflammatory agent from natural
resources.
Abstract: The present study was done to evaluate the presence
of tetracycline resistance genes in Lactococcus garvieae isolated
from cultured rainbow trout, West Iran. The isolates were examined
for antimicrobial resistance using disc diffusion method. Of the 49
strains tested, 19 were resistant to tetracycline (38.7%), 32 to
enrofloxacin (65.3%), 21 to erythromycin (42.8%), 20 to
chloramphenicol and trimetoprim-sulfamethoxazole (40.8%). The
strains were then characterized for their genotypic resistance profiles.
The results revealed that all 49 isolates contained at least one of the
tetracycline resistance genes. Tet (A) was found in 89.4% of
tetracycline resistant isolates and the frequency of other gene were as
follows: tet (E) 42.1%, tet (B) 47.3%, tet (D) 15.7%, tet (L) 26.3%,
tet (K) 52.6%, tet (G) 36.8%, tet (34) 21%, tet (S) 63.1%, tet (C)
57.8%, tet (M) 73.6%, tet (O) 42.1%. The results revealed high levels
of antibiotic resistance in L. garvieae strains which is a potential
danger for trout culture as well as for public health.
Abstract: The rate of natural gas dissociation from the Coal
Matrix depends on depressurization of reservoir through removing of
the cleat water from the coal seam. These waters are similar to brine
and aged of very long years. For improving the connectivity through
fracking /fracturing, high pressure liquids are pumped off inside the
coal body. A significant quantity of accumulated water, a combined
mixture of cleat water and fracking fluids (back flow water) is
pumped out through gas well. In Queensland, Australia Coal Seam
Gas (CSG) industry is in booming state and estimated of 30,000 wells
would be active for CSG production forecasting life span of 30 years.
Integrated water management along with water softening programs is
practiced for subsequent treatment and later on discharge to nearby
surface water catchment. Water treatment is an important part of the
CSG industry. A case study on a CSG site and review on the test
results are discussed for assessing the Standards & Practices for
management of CSG by-product water and their subsequent disposal
activities. This study was directed toward (i) water management and
softening process in Spring Gully CSG field, (ii) Comparative
analysis on experimental study and standards and (iii) Disposal of the
treated water. This study also aimed for alternative usages and their
impact on vegetation, living species as well as long term effects.
Abstract: Composite materials, due to their unique properties
such as high strength to weight ratio, corrosion resistance, and impact
resistance have huge potential as structural materials in automotive,
construction and transportation applications. However, these
properties often come at higher cost owing to complex design
methods, difficult manufacturing processes and raw material cost.
Traditionally, tapered laminated composite structures are
manufactured using autoclave manufacturing process by ply drop off
technique. Autoclave manufacturing though very powerful suffers
from high capital investment and higher energy consumption. As per
the current trends in composite manufacturing, Out of Autoclave
(OoA) processes are looked as emerging technologies for
manufacturing the structural composite components for aerospace
and defense applications. However, there is a need for improvement
among these processes to make them reliable and consistent. In this
paper, feasibility of using out of autoclave process to manufacture the
variable thickness cantilever beam is discussed. The minimum weight
design for the composite beam is obtained using constant stress beam
concept by tailoring the thickness of the beam. Ply drop off
techniques was used to fabricate the variable thickness beam from
glass/epoxy prepregs. Experiments were conducted to measure
bending stresses along the span of the cantilever beam at different
intervals by applying the concentrated load at the free end.
Experimental results showed that the stresses in the bean at different
intervals were constant. This proves the ability of OoA process to
manufacture the constant stress beam. Finite element model for the
constant stress beam was developed using commercial finite element
simulation software. It was observed that the simulation results
agreed very well with the experimental results and thus validated
design and manufacturing approach used.
Abstract: For cycling, the analysis of the pedal force is one of the
important factors in the study of exercise ability assessment and
overuse injuries. In past studies, a two-axis measurement sensor was
used at the sagittal plane to measure the force only in the anterior,
posterior, and vertical directions and to analyze the loss of force and
the injury on the frontal plane due to the forces in the right and left
directions. In this study, which is a basic study on diverse analyses of
the pedal force that consider the forces on the sagittal plane and the
frontal plane, a three-axis pedal force measurement sensor was
developed to measure the anterior-posterior (Fx), medio-lateral (Fz),
and vertical (Fy) forces. The sensor was fabricated with a size and
shape similar to those of the general flat pedal, and had a 550g weight
that allowed smooth pedaling. Its measurement range was ±1000 N for
Fx and Fz and ±2000 N for Fy, and its non-linearity, hysteresis, and
repeatability were approximately 0.5%. The data were sampled at
1000 Hz using a signal collector. To use the developed sensor, the
pedaling efficiency (index of efficiency, IE) and the range of left and
right (medio-lateral, ML) forces were measured with two seat heights
(low and high). The results of the measurement showed that the IE was
higher and the force range in the ML direction was lower with the high
position than with the low position. The developed measurement
sensor and its application results will be useful in understanding and
explaining the complicated pedaling technique, and will enable
diverse kinematic analyses of the pedal force on the sagittal plane and
the frontal plane.
Abstract: The effect of the inclusion of thyme and rosemary
essential oils into chitosan films, as well as the microbiological and
physical properties when storing chitosan film with and without the
mentioned inclusion was studied. The film forming solution was
prepared by dissolving chitosan (2%, w/v), polysorbate 80 (4% w/w
CH) and glycerol (16% w/w CH) in aqueous lactic acid solutions
(control). The thyme (TEO) and rosemary (REO) essential oils (EOs)
were included 1:1 w/w (EOs:CH) on their combination 50/50
(TEO:REO). The films were stored at temperatures of 5, 20, 33°C
and a relative humidity of 75% during four weeks. The films with
essential oil inclusion did not show an antimicrobial activity against
strains. This behavior could be explained because the chitosan only
inhibits the growth of microorganisms in direct contact with the
active sites. However, the inhibition capacity of TEO was higher than
the REO and a synergic effect between TEO:REO was found for S.
enteritidis strains in the chitosan solution.
Some physical properties were modified by the inclusion of
essential oils. The addition of essential oils does not affect the
mechanical properties (tensile strength, elongation at break, puncture
deformation), the water solubility, the swelling index nor the DSC
behavior. However, the essential oil inclusion can significantly
decrease the thickness, the moisture content, and the L* value of
films whereas the b* value increased due to molecular interactions
between the polymeric matrix, the loosing of the structure, and the
chemical modifications. On the other hand, the temperature and time
of storage changed some physical properties on the chitosan films.
This could have occurred because of chemical changes, such as
swelling in the presence of high humidity air and the reacetylation of
amino groups. In the majority of cases, properties such as moisture
content, tensile strength, elongation at break, puncture deformation,
a*, b*, chrome, 7E increased whereas water resistance, swelling
index, L*, and hue angle decreased.
Abstract: In the last few decades, many southeast-Asia women
migrate to Taiwan by marriage, and it usually takes several years for
them to acquire Taiwanese citizenship. This study investigates the
relationship between their citizenship acquisition and whether they
develop Taiwanese identities, and how does it affect their ethnical
identity towards their original ethnics. Furthermore, the present study
also explores that whether citizenship acquisition help the immigrant
women to explore the host society further and make commitment to it,
or the identification towards mainstream Taiwanese society is only
symbolic and superficial? One hundred and ninety-two immigrant
women were measured using Multigroup Ethnic Identity
Measure-Revised and a global 10-point ethnic identity question.
Correlation tests, t-test, and hierarchical regression were performed to
answer the above questions. The results revealed that citizenship
acquisition does help immigrant women to identify with Taiwanese
society, but it does not affect how they identify with their own ethnics.
Furthermore, the results also indicated that acquiring citizenship
would not help these immigrant women become involved in deeper
cultural exploration of Taiwan nor would it encourage them to make
commitments to the host society.
Abstract: Although it is not intended to identify distance
education students as a homogeneous group, recent research has
demonstrated that there are some demographic and personality
common traits among most of them that provide the basis for the
description of a typical distance learning student. The purpose of this
paper is to describe these common traits and to facilitate their
learning journey within a distance education program. The described
research is an initiative of the Distance Education Unit at the
European University Cyprus (Laureate International Universities) in
the context of its action for the improvement of the students’
performance.
Abstract: Lightweight design represents an important key to
successful implementation of energy-saving, fuel-efficient and
environmentally friendly means of transport in the aerospace and
automotive industry. In this context the use of carbon fibre reinforced
plastics (CFRP) which are distinguished by their outstanding
mechanical properties at relatively low weight, promise significant
improvements. Due to the reduction of the total mass, with the
resulting lowered fuel or energy consumption and CO2 emissions
during the operational phase, commercial aircraft will increasingly be
made of CFRP. An auspicious technology for the efficient and
economic production of high performance thermoset composites and
hybrid structures for future lightweight applications is the
combination of carbon fibre sheet moulding compound, tailored
continuous carbon fibre reinforcements and metallic components in a
one-shot pressing and curing process. This paper deals with a hybrid
composite technology for aerospace industries, which was developed
with the help of a special innovation and development system.
Abstract: The transition period of Kosovo society brought
fundamental changes in all the spheres of organizing life. This was
the period when also in the cultural tradition the biggest movement
and an emerging from ‘isolation’ or from the ‘shell’ occurred.
Transformation of the traditional and embracing of the modern began
here. The same was experienced and is currently being experienced
also by Gjakova and its surrounding which is historically renowned
for its great tradition and culture.
The population of this region is actually facing a transition from
the traditional system into the modern one and quite often with huge
leaps.
These ‘movements’ or ‘evolutions’ of the society of this region,
besides the numerous positive things it ‘harvested’, also brought
things that do not at all correspond with their tradition as well as new
criminal occurrences which in the past were not present in this area.
Furthermore, some of the ‘new’ behaviors that are embraced from
other ‘cultures’ and ‘civilizations’, and which are often exceeded, are
quite perturbing. The security situation is also worrying, particularly
following the appearance of some new criminal occurrences.
Therefore, with this research paper we will strive to analyze the
new cultural “intersections” as well as the nature of the origin of
some new very worrying criminal occurrences. We will present there
also some factors inciting into these occurrences, which were
confessed by the persons involved in these criminal occurrences and
who come from this very region.
Abstract: Worldwide, most PILC MV underground cables in use
are approaching the end of their design life; hence, failures are likely
to increase. This paper studies the electric field and potential
distributions within the PILC insulted cable containing common
void-defect. The finite element model of the performance of the
belted PILC MV underground cable is presented. The variation of the
electric field stress within the cable using the Finite Element Method
(FEM) is concentrated. The effects of the void-defect within the
insulation are given. Outcomes will lead to deeper understanding of
the modeling of Paper Insulated Lead Covered (PILC) and electric
field response of belted PILC insulted cable containing void defect.
Abstract: Spam is any unwanted electronic message or material
in any form posted too many people. As the world is growing as
global world, social networking sites play an important role in
making world global providing people from different parts of the
world a platform to meet and express their views. Among different
social networking sites Facebook become the leading one. With
increase in usage different users start abusive use of Facebook by
posting or creating ways to post spam. This paper highlights the
potential spam types nowadays Facebook users’ faces. This paper
also provide the reason how user become victim to spam attack. A
methodology is proposed in the end discusses how to handle different
types of spam.
Abstract: Locating Radio Controlled (RC) devices using their
unintended emissions has a great interest considering security
concerns. Weak nature of these emissions requires near field
localization approach since it is hard to detect these signals in far
field region of array. Instead of only angle estimation, near field
localization also requires range estimation of the source which makes
this method more complicated than far field models. Challenges of
locating such devices in a near field region and real time environment
are analyzed in this paper. An ESPRIT like near field localization
scheme is utilized for both angle and range estimation. 1-D search
with symmetric subarrays is provided. Two 7 element uniform linear
antenna arrays (ULA) are employed for locating RC source.
Experiment results of location estimation for one unintended emitting
walkie-talkie for different positions are given.
Abstract: Testing the first year students of Informatics at the
University of Debrecen revealed that students start their tertiary
studies in programming with a low level of programming knowledge
and algorithmic skills. The possible reasons which lead the students
to this very unfortunate result were examined. The results of the test
were compared to the students’ results in the school leaving exams
and to their self-assessment values. It was found that there is only a
slight connection between the students’ results in the test and in the
school leaving exams, especially at intermediate level. Beyond this,
the school leaving exams do not seem to enable students to evaluate
their own abilities.
Abstract: In-memory database systems are becoming popular
due to the availability and affordability of sufficiently large RAM and
processors in modern high-end servers with the capacity to manage
large in-memory database transactions. While fast and reliable inmemory
systems are still being developed to overcome cache misses,
CPU/IO bottlenecks and distributed transaction costs, disk-based data
stores still serve as the primary persistence. In addition, with the
recent growth in multi-tenancy cloud applications and associated
security concerns, many organisations consider the trade-offs and
continue to require fast and reliable transaction processing of diskbased
database systems as an available choice. For these
organizations, the only way of increasing throughput is by improving
the performance of disk-based concurrency control. This warrants a
hybrid database system with the ability to selectively apply an
enhanced disk-based data management within the context of inmemory
systems that would help improve overall throughput.
The general view is that in-memory systems substantially
outperform disk-based systems. We question this assumption and
examine how a modified variation of access invariance that we call
enhanced memory access, (EMA) can be used to allow very high
levels of concurrency in the pre-fetching of data in disk-based
systems. We demonstrate how this prefetching in disk-based systems
can yield close to in-memory performance, which paves the way for
improved hybrid database systems. This paper proposes a novel EMA
technique and presents a comparative study between disk-based EMA
systems and in-memory systems running on hardware configurations
of equivalent power in terms of the number of processors and their
speeds. The results of the experiments conducted clearly substantiate
that when used in conjunction with all concurrency control
mechanisms, EMA can increase the throughput of disk-based systems
to levels quite close to those achieved by in-memory system. The
promising results of this work show that enhanced disk-based
systems facilitate in improving hybrid data management within the
broader context of in-memory systems.
Abstract: The purpose of this study is to examine the possible
link between employee and customer satisfaction. The service
provided by employees, help to build a good relationship with
customers and can help at increasing their loyalty. Published data for
job satisfaction and indicators of customer services of banks were
gathered from relevant published works which included data from
five different countries. The scores of customers and employees
satisfaction of the different published works were transformed and
normalized to the scale of 1 to 100. The data were analyzed and a
regression analysis of the two parameters was used to describe the
link between employee’s satisfaction and customer’s satisfaction.
Assuming that employee satisfaction has a significant influence on
customer’s service and the resulting customer satisfaction, the
reviewed data indicate that employee’s satisfaction contributes
significantly on the level of customer satisfaction in the Banking
sector. There was a significant correlation between the two
parameters (Pearson correlation R2=0.52 P
Abstract: Wet scrubbers have found widespread use in cleaning
contaminated gas streams because of their ability to remove
particulates and based on the applications of scrubbing of marine
engine exhaust gases by spraying sea-water. In order to examine the
flow characteristics inside the scrubber, the model is designated with
flow properties of hot air and water sprayer. The flow dynamics of
evaporation of hot air by the injection of water droplets is the key
factor considered in this paper. The flow behavior inside the scrubber
was investigated from the previous works and to sum up the
evaporation rate with respect to the concentration of water droplets are
predicted to bring out the competent modelling. The numerical
analysis using CFD facilitates in understanding the problem better and
empathies the behavior of the model over its entire operating envelope.
Abstract: Cost of governance in Nigeria has become a challenge
to development and concern to practitioners and scholars alike in the
field of business and social science research. In the 2010 national
budget of NGN4.6 trillion or USD28.75billion for instance, only a
pantry sum of NGN1.8trillion or USD11.15billion was earmarked for
capital expenditure. Similarly, in 2013, out of a total national budget
of NGN4.92trillion or USD30.75billion, only the sum of
NGN1.50trllion or USD9.38billion was voted for capital expenditure.
Therefore, based on the data sourced from the Nigerian Office of
Statistics, Central bank of Nigeria Statistical Bulletin as well as from
the United Nations Development Programme, this study examined
the causes of high cost of governance in Nigeria. It found out that the
high cost of governance in the country is in the interest of the ruling
class, arising from their unethical behaviour – corrupt practices and
the poor management of public resources. As a result, the study
recommends the need to intensify the war against corruption and
mismanagement of public resources by government officials as
possible solution to overcome the high cost of governance in Nigeria.
This could be achieved by strengthening the constitutional powers of
the various anti-corruption agencies in the area of arrest, investigation
and prosecution of offenders without the interference of the executive
arm of government either at the local, state or federal level.