Abstract: In rapid industrial development, the demand for
high-strength and lightweight materials have been increased. Thus,
various CFRP (Carbon Fiber Reinforced Plastics) with composite
materials are being used. The design variables of CFRP are its
lamination direction, order and thickness. Thus, the hardness and
strength of CFRP depends much on their design variables. In this
paper, the lamination direction of CFRP was used to produce a
symmetrical ply [0°/0°, -15°/+15°, -30°/+30°, -45°/+45°, -60°/+60°,
-75°/+75° and 90°/90°] and an asymmetrical ply [0°/15°, 0°/30°,
0°/45°, 0°/60° 0°/75° and 0°/90°]. The bending flexure stress of the
CFRP specimen was evaluated through a bending test. Its thermal
property was measured using an infrared camera. The symmetrical
specimen and the asymmetrical specimen were analyzed. The results
showed that the asymmetrical specimen increased the bending loads
according to the increase in the orientation angle; and from 0°, the
symmetrical specimen showed a tendency opposite the asymmetrical
tendency because the tensile force of fiber differs at the vertical
direction of its load. Also, the infrared camera showed that the thermal
property had a trend similar to that of the mechanical properties.
Abstract: This study examines analytically the effect of tsunami loads on reinforced concrete (RC) frame buildings. The impact of tsunami wave loads and waterborne objects are analyzed using a typical substandard full-scale two-story RC frame building tested as part of the EU-funded Ecoleader project. The building was subjected to shake table tests in bare condition, and subsequently strengthened using Carbon Fiber Reinforced Polymers (CFRP) composites and retested. Numerical models of the building in both bare and CFRP-strengthened conditions are calibrated in DRAIN-3DX software to match the test results. To investigate the response of wave loads and impact forces, the numerical models are subjected to nonlinear dynamic analyses using force time-history input records. The analytical results are compared in terms of displacements at the floors and at the “impact point” of a boat. The results show that the roof displacement of the CFRP-strengthened building reduced by 63% when compared to the bare building. The results also indicate that strengthening only the mid-height of the impact column using CFRP is more effective at reducing damage when compared to strengthening other parts of the column. Alternative solutions to mitigate damage due to tsunami loads are suggested.
Abstract: In this paper, some relative efficiency have been
discussed, including the LSE estimate with respect to BLUE in curve
model. Four new kinds of relative efficiency have defined, and their
upper bounds have been discussed.
Abstract: This paper examines how “Zakat” provides fair
income redistribution and aids the struggle against poverty. Providing
fair income redistribution and combating poverty constitutes some of
the fundamental tasks performed by countries all over the world.
Each country seeks a solution for these problems according to their
political, economic and administrative styles through applying
various economic and financial policies. The same situation can be
handled via “zakat” association in Islam. Nowadays, we observe
different versions of “zakat” in developed countries. Applications
such as negative income tax denote merely a different form of
“zakat” that is being applied almost in the same way but under
changed names. However, the minimum values to donate under zakat
(e.g. 85 gr. gold and 40 animals) get altered and various amounts are
put into practice. It might be named as negative income tax instead of
zakat, nonetheless, these applications are based on the Holy Koran
and the hadith released 1400 years ago. Besides, considering the
savage and slavery in the world at those times, we might easily
recognize the true value of the zakat being applied for the first time
then in the Islamic system. Through zakat, governments are able to
transfer incomes to the poor as a means of enabling them achieve the
minimum standard of living required. With regards to who benefits
from the Zakat, an objective and fair criteria was used to determine
who benefits from the zakat contrary to the notion that it was based
on peoples’ own choices. Since the zakat is obligatory, the transfers
do not get forwarded directly but via the government and get
distributed, which requires vast governmental organizations. Through
the application of Zakat, reduced levels of poverty can be achieved
and also ensure the fair income redistribution.
Abstract: It is important to take security measures to protect
your computer information, reduce identify theft, and prevent from
malicious cyber-attacks. With cyber-attacks on the continuous rise,
people need to understand and learn ways to prevent from these
attacks. Cyber-attack is an important factor to be considered if one is
to be able to protect oneself from malicious attacks. Without proper
security measures, most computer technology would hinder home
users more than such technologies would help. Knowledge of how
cyber-attacks operate and protective steps that can be taken to reduce
chances of its occurrence are key to increasing these security
measures. The purpose of this paper is to inform home users on the
importance of identifying and taking preventive steps to avoid cyberattacks.
Throughout this paper, many aspects of cyber-attacks will be
discuss: what a cyber-attack is, the affects of cyber-attack for home
users, different types of cyber-attacks, methodology to prevent such
attacks; home users can take to fortify security of their computer.
Abstract: The paper deals with the diagnostics of steel roof
structure of the winter sports halls built in 1970 year. The necessity
of the diagnostics has been given by the requirement to the evaluation
design of this structure, which has been caused by the new situation
in the field of the loadings given by the validity of the European
Standards in the Czech Republic from 2010 year. Due to these
changes in the normative rules, in practice existing structures are
gradually subjected to the evaluation design and depending on its
results to the strengthening or reconstruction, respectively. Steel roof
is composed of plane truss main girders, purlins and bracings and the
roof structure is supported by two arch main girders with the span of
L = 84 m. The in situ diagnostics of the roof structure was oriented to
the following parts: (i) determination and evaluation of the actual
material properties of used steel and (ii) verification of the actual
dimensions of the structural members. For the solution the nondestructive
methods have been used for in situ measurement. For the
indicative determination of steel strengths the modified method based
on the determination of Rockwell’s hardness has been used. For the
verification of the member’s dimensions (thickness of hollow
sections) the ultrasound method has been used. This paper presents
the results obtained using these testing methods and their evaluation,
from the viewpoint of the usage for the subsequent static assessment
and design evaluation of the existing structure. For the comparison,
the examples of the similar evaluations realized for steel structures of
the stadiums in Olomouc and Jihlava cities are briefly illustrated, too.
Abstract: In this paper, we propose an intelligent system that is
used for monitoring the health conditions of patients. Monitoring the
health condition of patients is a complex problem that involves
different medical units and requires continuous monitoring especially
in rural areas because of inadequate number of available specialized
physicians. The proposed system will improve patient care and drive
costs down comparing to the existing system in Jordan. The proposed
system will be the start point to faster and improve the
communication between different units in the health system in
Jordan. Connecting patients and their physicians beyond hospital
doors regarding their geographical area is an important issue in
developing the health system in Jordan. The ability of making
medical decisions, the quality of medical is expected to be improved.
Abstract: In this investigation, we have evaluated the effects of
arsenic trioxide on hepatic function in pregnant and lactating Swiss
albino mice and their suckling pups. Experiments were carried out on
female mice given 175 ppm As2O3 in their drinking water from the
14th day of pregnancy until day 14 after delivery. Our results showed
a significant decrease in plasma levels of total protein and albumin,
cholesterol and triglyceride in As2O3 treated mice and their pups. The
hyperbilirubinemia and the increased plasma total alkaline
phosphatase activity suggested the presence of cholestasis.
Transaminase activities as well as lactate deshydrogenase activity in
plasma, known as biomarkers of hepatocellular injury, were elevated
indicating hepatic cells’ damage after treatment with As2O3.
Exposure to arsenic led to an increase of liver thiobarbituric acid
reactive substances level along with a concomitant decrease in the
activities of superoxide dismutase, catalase and glutathione
peroxidase and in glutathione.
Abstract: Near-infrared spectroscopy (NIRS) has been widely
used as a non-invasive method to measure brain activity, but it is
corrupted by baseline drift noise. Here we present a method to measure
regional cerebral blood flow as a derivative of NIRS output. We
investigate whether, when listening to languages, blood flow can
reasonably localize and represent regional brain activity or not. The
prefrontal blood flow distribution pattern when advanced
second-language listeners listened to a second language (L2) was most
similar to that when listening to their first language (L1) among the
patterns of mean and standard deviation. In experiments with 25
healthy subjects, the maximum blood flow was localized to the left
BA46 of advanced listeners. The blood flow presented is robust to
baseline drift and stably localizes regional brain activity.
Abstract: Social Media (SM) is websites increasingly popular
and built to allow people to express themselves and to interact
socially with others. Most SMT are dominated by youth particularly
College students. The proliferation of popular social media tools,
which can accessed from any communication devices has become
pervasive in the lives of today’s student life. Connecting traditional
education to social media tools are a relatively new era and any
collaborative tool could be used for learning activities. This study
focuses (i) how the social media tools are useful for the learning
activities of the students of faculty of medicine in King Khalid
University (ii) whether the social media affects the collaborative
learning with interaction among students, among course instructor,
their engagement, perceived ease of use and perceived ease of
usefulness (TAM) (iii) overall, the students satisfy with this
collaborative learning through Social media.
Abstract: For the treatment of acute and chronic lung diseases it is preferred to deliver medicaments by inhalation. The drug is delivered directly to tracheobronchial tree. This way allows the given medicament to get directly into the place of action and it makes rapid onset of action and maximum efficiency. The transport of aerosol particles in the particular part of the lung is influenced by their size, anatomy of the lungs, breathing pattern and airway resistance. This article deals with calculation of airway resistance in the lung model of Horsfield. It solves the problem of determination of the pressure losses in bifurcation and thus defines the pressure drop at a given location in the bronchial tree. The obtained data will be used as boundary conditions for transport of aerosol particles in a central part of bronchial tree realized by Computational Fluid Dynamics (CFD) approach. The results obtained from CFD simulation will allow us to provide information on the required particle size and optimal inhalation technique for particle transport into particular part of the lung.
Abstract: Elastomeric dielectric material has recently become a
new alternative for actuator technology. The characteristics of
dielectric elastomers placed between two electrodes to withstand
large strain when electrodes are charged has attracted the attention of
many researcher to study this material for actuator technology. Thus,
in the past few years Danfoss Ventures A/S has established their own
dielectric electro-active polymer (DEAP), which was called
PolyPower.
The main objective of this work was to investigate the dynamic
characteristics for vibration control of a PolyPower actuator folded in
‘pull’ configuration. A range of experiments was carried out on the
folded actuator including passive (without electrical load) and active
(with electrical load) testing. For both categories static and dynamic
testing have been done to determine the behavior of folded DEAP
actuator.
Voltage-Strain experiments show that the DEAP folded actuator is
a non-linear system. It is also shown that the voltage supplied has no
effect on the natural frequency. Finally, varying AC voltage with
different amplitude and frequency shows the parameters that
influence the performance of DEAP folded actuator. As a result, the
actuator performance dominated by the frequency dependence of the
elastic response and was less influenced by dielectric properties.
Abstract: The 3D body movement signals captured during
human-human conversation include clues not only to the content of
people’s communication but also to their culture and personality.
This paper is concerned with automatic extraction of this information
from body movement signals. For the purpose of this research, we
collected a novel corpus from 27 subjects, arranged them into groups
according to their culture. We arranged each group into pairs and
each pair communicated with each other about different topics.
A state-of-art recognition system is applied to the problems of
person, culture, and topic recognition. We borrowed modeling,
classification, and normalization techniques from speech recognition.
We used Gaussian Mixture Modeling (GMM) as the main technique
for building our three systems, obtaining 77.78%, 55.47%, and
39.06% from the person, culture, and topic recognition systems
respectively. In addition, we combined the above GMM systems with
Support Vector Machines (SVM) to obtain 85.42%, 62.50%, and
40.63% accuracy for person, culture, and topic recognition
respectively.
Although direct comparison among these three recognition
systems is difficult, it seems that our person recognition system
performs best for both GMM and GMM-SVM, suggesting that intersubject
differences (i.e. subject’s personality traits) are a major
source of variation. When removing these traits from culture and
topic recognition systems using the Nuisance Attribute Projection
(NAP) and the Intersession Variability Compensation (ISVC)
techniques, we obtained 73.44% and 46.09% accuracy from culture
and topic recognition systems respectively.
Abstract: The concentration levels of six heavy metals (Cd, Cr,
Fe, Ni, Pb and Zn) and two mineral elements (Ca and Mg) were
determined in soil samples collected from the vicinity of two auto
mechanic workshops in Sabon-Gari, Kaduna state, Nigeria, using
Atomic Absorption Spectrometry (AAS), in order to compare the
gradation of their concentrations with distance and depth of soil from
the workshop sites. At site 1, concentrations of Lead, Chromium, Iron
and Zinc were generally found to be above the World Health
Organization limits, while those of Nickel and Cadmium fell within
the limits. Iron had the highest concentration with a range of 176.274
ppm to 489.127 ppm at depths of 5 cm to 15 cm and a distance range
of 5 m to 15 m, while the concentration of cadmium was least with a
range of 0.001 ppm to 0.008 ppm at similar depth and distance
ranges. In addition, there was more of calcium (11.521 ppm to
121.709 ppm), in all the samples, than magnesium (11.293 ppm to
21.635 ppm). Similar results were obtained for site II. The
concentrations of all the metals analyzed showed a downward
gradient with increase in depth and distance from both workshop sites
except for iron and zinc at site 2. The immediate and remote
implications of these findings on the biota are discussed.
Abstract: The legends about “user-friendly” and “easy-to-use”
birotical tools (computer-related office tools) have been spreading
and misleading end-users. This approach has led us to the extremely
high number of incorrect documents, causing serious financial losses
in the creating, modifying, and retrieving processes. Our research
proved that there are at least two sources of this underachievement:
(1) The lack of the definition of the correctly edited, formatted
documents. Consequently, end-users do not know whether their
methods and results are correct or not. They are not aware of their
ignorance. They are so ignorant that their ignorance does not allow
them to realize their lack of knowledge. (2) The end-users’ problem
solving methods. We have found that in non-traditional programming
environments end-users apply, almost exclusively, surface approach
metacognitive methods to carry out their computer related activities,
which are proved less effective than deep approach methods.
Based on these findings we have developed deep approach
methods which are based on and adapted from traditional
programming languages. In this study, we focus on the most popular
type of birotical documents, the text based documents. We have
provided the definition of the correctly edited text, and based on this
definition, adapted the debugging method known in programming.
According to the method, before the realization of text editing, a
thorough debugging of already existing texts and the categorization
of errors are carried out. With this method in advance to real text
editing users learn the requirements of text based documents and also
of the correctly formatted text.
The method has been proved much more effective than the
previously applied surface approach methods. The advantages of the
method are that the real text handling requires much less human and
computer sources than clicking aimlessly in the GUI (Graphical User
Interface), and the data retrieval is much more effective than from
error-prone documents.
Abstract: This review emphasizes the effectiveness of men’s
participation in preventing domestic violence, and whether nonviolent
(NV) boys’ and men’s perceptions of intimate partner
violence (IPV) prevention programs affect their involvement. The
main goals of this assessment were to investigate (1) how NV men
engaged in anti-violence prevention programs that empower women,
(2) what were the possible perceptions of NV men involved in
prevention programs (3) how to identify effective approaches and
strategies that encouraged NV men to become involved in prevention
programs. This critical review also included the overview of
prevention programs such as: The Mentors in Violence Prevention
Programs (MVP), The White Ribbon Campaign (WRC), and
Domestic Violence Prevention Enhancement and Leadership through
Alliances (DELTA). The review suggested that (1) the expanding
prevention programs need to reach more macro settings such as work
place, faith-based and other community based organizations, and (2)
territory prevention programs should expand through addressing the
long-term effects of violence.
Abstract: This study carried out comparative seismic
performance of reinforced concrete frames infilled by masonry walls
with different heights. Partial and fully infilled reinforced concrete
frames were modeled for the research objectives and the analysis
model for a bare reinforced concrete frame was also established for
comparison. Non–linear static analyses for the studied frames were
performed to investigate their structural behavior under extreme
seismic loads and to find out their collapse mechanism. It was
observed from analysis results that the strengths of the partial infilled
reinforced concrete frames are increased and their ductilities are
reduced, as infilled masonry walls are higher. Especially, reinforced
concrete frames with higher partial infilled masonry walls would
experience shear failures. Non–linear dynamic analyses using 10
earthquake records show that the bare and fully infilled reinforced
concrete frame present stable collapse mechanism while the reinforced
concrete frames with partially infilled masonry walls collapse in more
brittle manner due to short-column effects.
Abstract: Solar energy is a good option among renewable
energy resources due to its easy availability and abundance. The
simplest and most efficient way to utilize solar energy is to convert it
into thermal energy and this can be done with the help of solar
collectors. The thermal performance of such collectors is poor due to
less heat transfer from the collector surface to air. In this work,
experimental investigations of single pass solar air heater having
triangular duct and provided with roughness element on the underside
of the absorber plate. V-shaped ribs are used for investigation having
three different values of relative roughness pitch (p/e) ranges from 4-
16 for a fixed value of angle of attack (α), relative roughness height
(e/Dh) and a relative gap distance (d/x) values are 60°, 0.044 and 0.60
respectively. Result shows that considerable augmentation in heat
transfer has been obtained by providing roughness.
Abstract: This research focused on comparing the critical
thinking of the teacher students before and after using Miller’s Model
learning activities and investigating their opinions. The sampling
groups were (1) fourth year 33 student teachers majoring in Early
Childhood Education and enrolling in semester 1 of academic year
2013 (2) third year 28 student teachers majoring in English and
enrolling in semester 2 of academic year 2013 and (3) third year 22
student teachers majoring in Thai and enrolling in semester 2 of
academic year 2013. The research instruments were (1) lesson plans
where the learning activities were settled based on Miller’s Model (2)
critical thinking assessment criteria and (3) a questionnaire on
opinions towards Miller’s Model based learning activities. The
statistical treatment was mean, deviation, different scores and T-test.
The result unfolded that (1) the critical thinking of the students after
the assigned activities was better than before and (2) the students’
opinions towards the critical thinking improvement activities based
on Miller’s Model ranged from the level of high to highest.
Abstract: In this study was monitored the population of the
European Pond Turtle, Emys orbicularis (Linnaeus, 1758) in the area
of Narta Lagoon, Vlora Bay (Albania), from August to October 2014.
A total of 54 individuals of E. orbicularis were studied using
different methodologies. Curved Carapace Length (CCL), Plastron
Length (PL) and Curved Carapace Width (CCW) were measured for
each individual of E. orbicularis and were statistically analyzed. All
captured turtles were separated in seven different size – classes based
on their carapace length (CCL). Each individual of E. orbicularis was
marked by notching the carapace (marginal scutes). Form all
individuals captured resulted that 37 were females (68.5%), 14 males
(25.9%), 3 juveniles (5.5%), while 18 individuals of E. orbicularis
were recaptured for the first and some for the second time.