Abstract: Elastic scattering of α-particles from 9Be and 11B
nuclei at different alpha energies have been analyzed. Optical model
parameters (OMPs) of α-particles elastic scattering by these nuclei at
different energies have been obtained. In the present calculations, the
real part of the optical potential are derived by folding of nucleonnucleon
(NN) interaction into nuclear matter density distribution of
the projectile and target nuclei using computer code FRESCO. A
density-dependent version of the M3Y interaction (CDM3Y6), which
is based on the G-matrix elements of the Paris NN potential, has been
used. Volumetric integrals of the real and imaginary potential depth
(JR, JW) have been calculated and found to be energy dependent.
Good agreement between the experimental data and the theoretical
predictions in the whole angular range. In double folding (DF)
calculations, the obtained normalization coefficient Nr is in the range
0.70–1.32.
Abstract: The exploitation of flow pulsation in micro- and
mini-channels is a potentially useful technique for enhancing cooling
of high-end photonics and electronics systems. It is thought that
pulsation alters the thickness of the hydrodynamic and thermal
boundary layers, and hence affects the overall thermal resistance
of the heat sink. Although the fluid mechanics and heat transfer
are inextricably linked, it can be useful to decouple the parameters
to better understand the mechanisms underlying any heat transfer
enhancement. Using two-dimensional, two-component particle image
velocimetry, the current work intends to characterize the heat transfer
mechanisms in pulsating flow with a mean Reynolds number of
48 by experimentally quantifying the hydrodynamics of a generic
liquid-cooled channel geometry. Flows circulated through the test
section by a gear pump are modulated using a controller to achieve
sinusoidal flow pulsations with Womersley numbers of 7.45 and
2.36 and an amplitude ratio of 0.75. It is found that the transient
characteristics of the measured velocity profiles are dependent on the
speed of oscillation, in accordance with the analytical solution for
flow in a rectangular channel. A large velocity overshoot is observed
close to the wall at high frequencies, resulting from the interaction
of near-wall viscous stresses and inertial effects of the main fluid
body. The steep velocity gradients at the wall are indicative of
augmented heat transfer, although the local flow reversal may reduce
the upstream temperature difference in heat transfer applications.
While unsteady effects remain evident at the lower frequency, the
annular effect subsides and retreats from the wall. The shear rate at
the wall is increased during the accelerating half-cycle and decreased
during deceleration compared to steady flow, suggesting that the flow
may experience both enhanced and diminished heat transfer during
a single period. Hence, the thickness of the hydrodynamic boundary
layer is reduced for positively moving flow during one half of the
pulsation cycle at the investigated frequencies. It is expected that the
size of the thermal boundary layer is similarly reduced during the
cycle, leading to intervals of heat transfer enhancement.
Abstract: In general, it is desirable to finish the weld quickly,
before a large volume of surrounding metal heats up and expands.
The welding process used, type, welding current and speed of travel,
thus, affect the degree of shrinkage and distortion of a weldment. The
use of mechanized welding equipment reduces welding time, metal
affected zone and consequently distortion. This article helps to define
what weld distortion is and then provide a practical understanding of
the causes of distortion, effects of shrinkage in butt joint welded
assemblies using TI6AL4VA and Aluminium AA2024 alloy sheet.
The beam offset position to the joint interface towards titanium and
aluminium side. The factors affecting distortion during welding is
also given. Test results reveal that welding speed is the significant
parameter to decide the extent of distortion. Also welding from Al
side reduces the distortion while Ti side increases the distortion.
Abstract: In this paper, we present the design of the
super-ellipsoidal potential function (SEPF), that can be used for
autonomous collision avoidance of an unmanned aerial vehicle (UAV)
in a 3-dimensional space. In the design of SEPF, we have the
full control over the shape and size of the potential function. In
particular, we can adjust the length, width, height, and the amount
of flattening at the tips of the potential function so that the collision
avoidance motion vector generated from the potential function can
be adjusted accordingly. Based on the idea of the SEPF, we also
propose an approach for the local autonomy of a UAV for its collision
avoidance when the UAV is teleoperated by a human operator. In
our proposed approach, a teleoperated UAV can not only avoid
collision autonomously with other surrounding objects but also track
the operator’s control input as closely as possible. As a result, an
operator can always be in control of the UAV for his/her high-level
guidance and navigation task without worrying too much about
the UAVs collision avoidance while it is being teleoperated. The
effectiveness of the proposed approach is demonstrated through a
human-in-the-loop simulation of quadrotor UAV teleoperation using
virtual robot experimentation platform (v-rep) and Matlab programs.
Abstract: Sisal leaves were subjected to enzymatic retting
method to extract the sisal fibre. A portion of the fibre was pretreated
with alkali (NaOH), and further treated with benzoyl chloride
and silane treatment reagents. Both the treated and untreated Sisal
fibre composites were used to fabricate the composite by hand lay-up
technique using unsaturated polyester resin. Tensile, flexural, water
absorption, density, thickness swelling and chemical resistant tests
were conducted and evaluated on the composites. Results obtained
for all the parameters showed an increase in the treated fibre
compared to untreated fibre. FT-IR spectra results ascertained the
inclusion of benzoyl and silane groups on the fibre surface. Scanning
electron microscopy (SEM) result obtained showed variation in the
morphology of the treated and untreated fibre. Chemical modification
was found to improve adhesion of the fibre to the matrix, as well as
physico-mechanical properties of the composites.
Abstract: The cumulative costs for O&M may represent as
much as 65%-90% of the turbine's investment cost. Nowadays the
cost effectiveness concept becomes a decision-making and
technology evaluation metric. The cost of energy metric accounts for
the effect replacement cost and unscheduled maintenance cost
parameters. One key of the proposed approach is the idea of
maintaining the WTs which can be captured via use of a finite state
Markov chain. Such a model can be embedded within a probabilistic
operation and maintenance simulation reflecting the action to be
done. In this paper, an approach of estimating the cost of O&M is
presented. The finite state Markov model is used for decision
problems with number of determined periods (life cycle) to predict
the cost according to various options of maintenance.
Abstract: The railway transport is considered as a one of the
most environmentally friendly mode of transport. With future
prediction of increasing of freight transport there are lines facing
problems with demanded capacity. Increase of the track capacity
could be achieved by infrastructure constructive adjustments. The
contribution shows how the travel time can be minimized and the
track capacity increased by changing some of the basic infrastructure
and operation parameters, for example, the minimal curve radius of
the track, the number of tracks, or the usable track length at stations.
Calculation of the necessary parameter changes is based on the
fundamental physical laws applied to the train movement, and
calculation of the occupation time is dependent on the changes of
controlling the traffic between the stations.
Abstract: Reinforced earth structures are generally subjected to cyclic loading generated from earthquakes. This paper presents a summary of the results and analyses of a testing program carried out in a large-scale multi-function geosynthetic testing apparatus that accommodates soil samples up to 1.0 m3. This apparatus performs different shear and pullout tests under both static and cyclic loading. The testing program was carried out to investigate the controlling factors affecting soil/geogrid interaction under cyclic loading. The extensibility of the geogrids, the applied normal stresses, the characteristics of the cyclic loading (frequency, and amplitude), and initial static load within the geogrid sheet were considered in the testing program. Based on the findings of the testing program, the effect of these parameters on the pullout resistance of geogrids, as well as the displacement mobility under cyclic loading were evaluated. Conclusions and recommendations for the design of reinforced earth walls under cyclic loading are presented.
Abstract: This article describes the implementation of an
experimental model for teaching ICT tools and digital environments
in teachers training college. In most educational systems in the
Western world, new programs were developed in order to bridge the
digital gap between teachers and students. In spite of their
achievements, these programs are limited due to several factors: The
teachers in the schools implement new methods incorporating
technological tools into the curriculum, but meanwhile the
technology changes and advances. The interface of tools changes
frequently, some tools disappear and new ones are invented. These
conditions require an experimental model of training the pre-service
teachers. The appropriate method for instruction within the domain of
ICT tools should be based on exposing the learners to innovations,
helping them to gain experience, teaching them how to deal with
challenges and difficulties on their own, and training them. This
study suggests some principles for this approach and describes step
by step the implementation of this model.
Abstract: The irradiation of polymeric materials has received
much attention because it can produce diverse changes in chemical
structure and physical properties. Thus, studying the chemical and
structural changes of polymers is important in practice to achieve
optimal conditions for the modification of polymers. The effect of
gamma irradiation on the crystalline structure of poly(vinylidene
fluoride) (PVDF) has been investigated using differential scanning
calorimetry (DSC) and X-ray diffraction techniques (XRD). Gamma
irradiation was carried out in atmosphere air with doses between 100
kGy at 3,000 kGy with a Co-60 source. In the melting thermogram of
the samples irradiated can be seen a bimodal melting endotherm is
detected with two melting temperature. The lower melting
temperature is attributed to melting of crystals originally present and
the higher melting peak due to melting of crystals reorganized upon
heat treatment. These results are consistent with those obtained by
XRD technique showing increasing crystallinity with increasing
irradiation dose, although the melting latent heat is decreasing.
Abstract: The adjoint method has been used as a successful tool to
obtain sensitivity gradients in aerodynamic design and optimisation
for many years. This work presents an alternative approach to the
continuous adjoint formulation that enables one to compute gradients
of a given measure of merit with respect to control parameters other
than those pertaining to geometry. The procedure is then applied to
the steady 2–D compressible Euler and incompressible Navier–Stokes
flow equations. Finally, the results are compared with sensitivities
obtained by finite differences and theoretical values for validation.
Abstract: Interaction between mixing and crystallization is often
ignored despite the fact that it affects almost every aspect of the
operation including nucleation, growth, and maintenance of the
crystal slurry. This is especially pronounced in multiple impeller
systems where flow complexity is increased. By choosing proper
mixing parameters, what closely depends on the knowledge of the
hydrodynamics in a mixing vessel, the process of batch cooling
crystallization may considerably be improved. The values that render
useful information when making this choice are mixing time and
power consumption. The predominant motivation for this work was
to investigate the extent to which radial dual impeller configuration
influences mixing time, power consumption and consequently the
values of metastable zone width and nucleation rate. In this research,
crystallization of borax was conducted in a 15 dm3 baffled batch
cooling crystallizer with an aspect ratio (H/T) of 1.3. Mixing was
performed using two straight blade turbines (4-SBT) mounted on the
same shaft that generated radial fluid flow. Experiments were
conducted at different values of N/NJS ratio (impeller speed/
minimum impeller speed for complete suspension), D/T ratio
(impeller diameter/crystallizer diameter), c/D ratio (lower impeller
off-bottom clearance/impeller diameter), and s/D ratio (spacing
between impellers/impeller diameter). Mother liquor was saturated at
30°C and was cooled at the rate of 6°C/h. Its concentration was
monitored in line by Na-ion selective electrode. From the values of
supersaturation that was monitored continuously over process time, it
was possible to determine the metastable zone width and
subsequently the nucleation rate using the Mersmann’s nucleation
criterion. For all applied dual impeller configurations, the mixing
time was determined by potentiometric method using a pulse
technique, while the power consumption was determined using a
torque meter produced by Himmelstein & Co. Results obtained in
this investigation show that dual impeller configuration significantly
influences the values of mixing time, power consumption as well as
the metastable zone width and nucleation rate. A special attention
should be addressed to the impeller spacing considering the flow
interaction that could be more or less pronounced depending on the
spacing value.
Abstract: Debts reconstruction under some of moratorium
projects is one of important method that highly benefits to both the
Banks and farmers. The method can reduce probabilities for nonprofits
loan. This paper discuss about debts reconstruction and career
development training for farmers in Thailand between 2011 and
2013. The research designed is mix-method between quantitative
survey and qualitative survey. Sample size for quantitative method is
1003 cases. Data gathering procedure is between October and
December 2013. Main results affirmed that debts reconstruction is
needed. And there are numerous benefits from farmers’ career
development training. Many of farmers who attend field school
activities able to bring knowledge learned to apply for the farms’
work. They can reduce production costs. Framers’ quality of life and
their household well-being also improve. This program should apply
in any countries where farmers have highly debts and highly risks for
not return the debts.
Abstract: Asphalt pavement itself is a mixture made up of mainly aggregates, binders, and fillers that acts as a composition used for pavement construction. An experimental program was setup to determine the fatigue performance test of Asphalt with three different grades of conventional binders. Asphalt specimen has achieved the maximum optimum bulk density and air voids with a consistent bulk density of 2.3 t/m3, with an air void of 5% ± 0.5, before loading into the Asphalt Mixture Performance Tested (AMPT) for fatigue test. The number of cycles is defined as the point where phase angle drops, which is caused by the formation of cracks due to the increasing micro cracks when asphalt is undergoing repeated cycles of loading. Thus, the data collected are analyzed using the drop of phase angle as failure criteria. Based in the data analyzed, it is evident that the fatigue life of asphalt lies on the grade of binder. The result obtained shows that all specimens do experience a drop in phase angle due to macro cracks in the asphalt specimen.
Abstract: Green chemistry for plant extraction of active principles is the main interest of many researchers concerned with climate change. While classical organic solvents are detrimental to our environment, greener alternatives to ionic liquids are very promising for sustainable organic chemistry. This study focused on the determination of functional groups observed in the main constituents from the ionic liquid extracts of Coleus aromaticus Benth leaves using FT-IR Spectroscopy. Moreover, this research aimed to determine the best ionic liquid that can separate functionalized plant constituents from the leaves Coleus aromaticus Benth using Fourier Transform Infrared Spectroscopy. Coleus aromaticus Benth leaf extract in different ionic liquids, elucidated pharmacologically important functional groups present in major constituents of the plant, namely, rosmarinic acid, caffeic acid and chlorogenic acid. In connection to distinctive appearance of functional groups in the spectrum and highest % transmittance, potassium chloride-glycerol is the best ionic liquid for green extraction.
Abstract: Ultrasonic metal welding has been the subject of ongoing research and development, most recently concentrating on metal joining in miniature devices, for example to allow solder-free wire bonding. As well as at the small scale, there are also opportunities to research the joining of thicker sheet metals and to widen the range of similar and dissimilar materials that can be successfully joined using this technology. This study presents the design, characterisation and test of a lateral-drive ultrasonic metal spot welding device. The ultrasonic metal spot welding horn is modelled using finite element analysis (FEA) and its vibration behaviour is characterised experimentally to ensure ultrasonic energy is delivered effectively to the weld coupon. The welding stack and fixtures are then designed and mounted on a test machine to allow a series of experiments to be conducted for various welding and ultrasonic parameters. Weld strength is subsequently analysed using tensile-shear tests. The results show how the weld strength is particularly sensitive to the combination of clamping force and ultrasonic vibration amplitude of the welding tip, but there are optimal combinations of these and also limits that must be clearly identified.
Abstract: The objective of this research is to develop a general technique so that one may predict the dynamic behaviour of a three-dimensional scale crane model subjected to time-dependent moving point forces by means of conventional finite element computer packages. To this end, the whole scale crane model is divided into two parts: the stationary framework and the moving substructure. In such a case, the dynamic responses of a scale crane model can be predicted from the forced vibration responses of the stationary framework due to actions of the four time-dependent moving point forces induced by the moving substructure. Since the magnitudes and positions of the moving point forces are dependent on the relative positions between the trolley, moving substructure and the stationary framework, it can be found from the numerical results that the time histories for the moving speeds of the moving substructure and the trolley are the key factors affecting the dynamic responses of the scale crane model.
Abstract: In this paper, autonomous performance of a small
manufactured unmanned helicopter is tried to be increased. For this
purpose, a small unmanned helicopter is manufactured in Erciyes
University, Faculty of Aeronautics and Astronautics. It is called as
ZANKA-Heli-I. For performance maximization, autopilot parameters
are determined via minimizing a cost function consisting of flight
performance parameters such as settling time, rise time, overshoot
during trajectory tracking. For this purpose, a stochastic optimization
method named as simultaneous perturbation stochastic approximation
is benefited. Using this approach, considerable autonomous
performance increase (around %23) is obtained.
Abstract: In this paper, it is aimed to improve autonomous flight
performance of a load-carrying (payload: 3 kg and total: 6kg)
unmanned aerial vehicle (UAV) through active wing and horizontal
tail active morphing and also integrated autopilot system parameters
(i.e. P, I, D gains) and UAV parameters (i.e. extension ratios of wing
and horizontal tail during flight) design. For this purpose, a loadcarrying
UAV (i.e. ZANKA-II) is manufactured in Erciyes
University, College of Aviation, Model Aircraft Laboratory is
benefited. Optimum values of UAV parameters and autopilot
parameters are obtained using a stochastic optimization method.
Using this approach autonomous flight performance of UAV is
substantially improved and also in some adverse weather conditions
an opportunity for safe flight is satisfied. Active morphing and
integrated design approach gives confidence, high performance and
easy-utility request of UAV users.
Abstract: Smart metering and demand response are gaining
ground in industrial and residential applications. Smart Appliances
have been given concern towards achieving Smart home. The success
of Smart grid development relies on the successful implementation of
Information and Communication Technology (ICT) in power sector.
Smart Appliances have been the technology under development and
many new contributions to its realization have been reported in the
last few years. The role of ICT here is to capture data in real time,
thereby allowing bi-directional flow of information/data between
producing and utilization point; that lead a way for the attainment of
Smart appliances where home appliances can communicate between
themselves and provide a self-control (switch on and off) using the
signal (information) obtained from the grid. This paper depicts the
background on ICT for smart appliances paying a particular attention
to the current technology and identifying the future ICT trends for
load monitoring through which smart appliances can be achieved to
facilitate an efficient smart home system which promote demand
response program. This paper grouped and reviewed the recent
contributions, in order to establish the current state of the art and
trends of the technology, so that the reader can be provided with a
comprehensive and insightful review of where ICT for smart
appliances stands and is heading to. The paper also presents a brief
overview of communication types, and then narrowed the discussion
to the load monitoring (Non-intrusive Appliances Load Monitoring
‘NALM’). Finally, some future trends and challenges in the further
development of the ICT framework are discussed to motivate future
contributions that address open problems and explore new
possibilities.