Abstract: In this study the regional stability of a rotor system which is supported on rolling bearings with radial clearance is studied. The rotor is assumed to be rigid. Due to radial clearance of bearings and dynamic configuration of system, each rolling elements of bearings has the possibility to be in contact with both of the races (under compression) or lose its contact. As a result, this change in dynamic of the system makes it to be known as switching system which is a type of Hybrid systems. In this investigation by adopting Multiple Lyapunov Function theorem and using Hamiltonian function as a candidate Lyapunov function, the stability of the system is studied. The purpose of this study is to inspect the regional stability of rotor-roller bearing and rotor-ball bearing systems.
Abstract: The case study deals with the semi-quantitative risk
assessment of water resource earmarked for the emergency supply
of population with drinking water. The risk analysis has been based
on previously identified hazards/sensitivities of the elements
of hydrogeological structure and technological equipment of ground
water resource as well as on the assessment of the levels of hazard,
sensitivity and criticality of individual resource elements in the form
of point indexes. The following potential sources of hazard have
been considered: natural disasters caused by atmospheric and
geological changes, technological hazards, and environmental
burdens. The risk analysis has proved that the assessed risks are
acceptable and the water resource may be integrated into a crisis plan
of a given region.
Abstract: This paper offers suggestions for educators at all levels about how to better prepare our students for the future, by building on the past. The discussion begins with a summary of changes in the World Wide Web, especially as the term Web 3.0 is being heard. The bulk of the discussion is retrospective and concerned with an overview of traditional teaching and research approaches as they evolved during the 20th century beginning with those grounded in the Cartesian reality of IA Richards- (1929) Practical Criticism. The paper concludes with a proposal of five strategies which incorporate timeless elements from the past as well as cutting-edge elements from today, in order to better prepare our students for the future.
Abstract: A mathematical model for the hydrodynamic
lubrication of parabolic slider bearings with couple stress lubricants
is presented. A numerical solution for the mathematical model using
finite element scheme is obtained using three nodes isoparametric
quadratic elements. Stiffness integrals obtained from the weak form
of the governing equations were solved using Gauss Quadrature to
obtain a finite number of stiffness matrices. The global system of
equations was obtained for the bearing and solved using Gauss Seidel
iterative scheme. The converged pressure solution was used to obtain
the load capacity of the bearing. Parametric studies were carried out
and it was shown that the effect of couple stresses and profile
parameter are to increase the load carrying capacity of the parabolic
slider bearing. Numerical experiments reveal that the magnitude of
the profile parameter at which maximum load is obtained increases
with decrease in couple stress parameter. The results are presented in
graphical form.
Abstract: In the paper the study of synthetic transmit aperture
method applying the Golay coded transmission for medical
ultrasound imaging is presented. Longer coded excitation allows to
increase the total energy of the transmitted signal without increasing
the peak pressure. Moreover signal-to-noise ratio and penetration
depth are improved while maintaining high ultrasound image
resolution. In the work the 128-element linear transducer array with
0.3 mm inter-element spacing excited by one cycle and the 8 and 16-
bit Golay coded sequences at nominal frequency 4 MHz was used. To
generate a spherical wave covering the full image region a single
element transmission aperture was used and all the elements received
the echo signals. The comparison of 2D ultrasound images of the
tissue mimicking phantom and in vitro measurements of the beef liver
is presented to illustrate the benefits of the coded transmission. The
results were obtained using the synthetic aperture algorithm with
transmit and receive signals correction based on a single element
directivity function.
Abstract: The paper presents a detailed calculation of characteristic of five different topology permanent magnet machines for high performance traction including hybrid -electric vehicles using finite element analysis (FEA) method. These machines include V-shape single layer interior PM, W-shape single-layer interior PM, Segment interior PM and surface PM on the rotor and with distributed winding on the stator. The performance characteristics which include the back-emf voltage and its harmonic, magnet mass, iron loss and ripple torque are compared and analyzed. One of a 7.5kW IPM prototype was tested and verified finite-element analysis results. The aim of the paper is given some guidance and reference for machine designer which are interested in IPM machine selection for high performance traction application.
Abstract: Resistance spot welding process comprises of electric,
thermal and mechanical phenomenon, which makes this process
complex and highly non-linear and thus, it becomes difficult to model
it. In order to obtain good weld nugget during spot welding, hit and
trial welds are usually done which is very costly. Therefore the
numerical simulation research has been conducted to understand the
whole process. In this paper three different cases were analyzed by
varying the tip contact area and it was observed that, with the
variation of tip contact area the nugget formation at the faying
surface is affected. The tip contact area of the welding electrode
becomes large with long welding cycles. Therefore in order to
maintain consistency of nugget formation during the welding process,
the current compensation in control feedback is required. If the
contact area of the welding electrode tip is reduced, a large amount of
current flows through the faying surface, as a result of which
sputtering occurs.
Abstract: Base on extenics theory, the statistical physical and mechanical properties from laboratory experiments are used to evaluate the bearing capacity of lateritic soil foundation. The properties include water content, bulk density, liquid limit, cohesion, and so on. The matter-element and the dependent function are defined. Then the synthesis dependent degree and the final grade index are calculated. The results show that predicted outcomes can be matched with the in-situ test data, and a evaluate grade associate with bearing capacity can be deduced. The results provide guidance to assess and determine the bearing capacity grade of lateritic soil foundation.
Abstract: Following harvest, fresh produce needs to be cooled
immediately in a room where the air temperature and the relative air
humidity are controlled to maintain the produce quality. In this paper,
an experimental study for forced air cooling of fresh produce
(cauliflower) is performed using a pilot developed within our
laboratory. Furthermore, a numerical simulation of spherical
produces, taking into account the aerodynamic aspect and also the
heat transfer in the produce and in the air, was carried out using a
finite element method. At the end of this communication,
experimental results are presented and compared with the simulation.
Abstract: The uses of road map in daily activities are numerous
but it is a hassle to construct and update a road map whenever there
are changes. In Universiti Malaysia Sarawak, research on Automatic
Road Extraction (ARE) was explored to solve the difficulties in
updating road map. The research started with using Satellite Image
(SI), or in short, the ARE-SI project. A Hybrid Simple Colour Space
Segmentation & Edge Detection (Hybrid SCSS-EDGE) algorithm
was developed to extract roads automatically from satellite-taken
images. In order to extract the road network accurately, the satellite
image must be analyzed prior to the extraction process. The
characteristics of these elements are analyzed and consequently the
relationships among them are determined. In this study, the road
regions are extracted based on colour space elements and edge details
of roads. Besides, edge detection method is applied to further filter
out the non-road regions. The extracted road regions are validated by
using a segmentation method. These results are valuable for building
road map and detecting the changes of the existing road database.
The proposed Hybrid Simple Colour Space Segmentation and Edge
Detection (Hybrid SCSS-EDGE) algorithm can perform the tasks
fully automatic, where the user only needs to input a high-resolution
satellite image and wait for the result. Moreover, this system can
work on complex road network and generate the extraction result in
seconds.
Abstract: In order to implement flexibility as well as survivable
capacities over passive optical network (PON), a new automatic
random fault-recovery mechanism with array-waveguide-grating
based (AWG-based) optical switch (OSW) is presented. Firstly,
wavelength-division-multiplexing and optical code-division
multiple-access (WDM/OCDMA) scheme are configured to meet the
various geographical locations requirement between optical network
unit (ONU) and optical line terminal (OLT). The AWG-base optical
switch is designed and viewed as central star-mesh topology to
prohibit/decrease the duplicated redundant elements such as fiber and
transceiver as well. Hence, by simple monitoring and routing switch
algorithm, random fault-recovery capacity is achieved over
bi-directional (up/downstream) WDM/OCDMA scheme. When error
of distribution fiber (DF) takes place or bit-error-rate (BER) is higher
than 10-9 requirement, the primary/slave AWG-based OSW are
adjusted and controlled dynamically to restore the affected ONU
groups via the other working DFs immediately.
Abstract: Stress Concentration Factors are significant in
machine design as it gives rise to localized stress when any change in
the design of surface or abrupt change in the cross section occurs.
Almost all machine components and structural members contain
some form of geometrical or microstructural discontinuities. These
discontinuities are very dangerous and lead to failure. So, it is very
much essential to analyze the stress concentration factors for critical
applications like Turbine Rotors. In this paper Finite Element
Analysis (FEA) with extremely fine mesh in the vicinity of the
blades of Steam Turbine Rotor is applied to determine stress
concentration factors. A model of Steam Turbine Rotor is shown in
Fig. 1.
Abstract: Reliable information about tool temperature
distribution is of central importance in metal cutting. In this study,
tool-chip interface temperature was determined in cutting of ST37
steel workpiece by applying HSS as the cutting tool in dry turning.
Two different approaches were implemented for temperature
measuring: an embedded thermocouple (RTD) in to the cutting tool
and infrared (IR) camera. Comparisons are made between
experimental data and results of MSC.SuperForm and FLUENT
software.
An investigation of heat generation in cutting tool was performed
by varying cutting parameters at the stable cutting tool geometry and
results were saved in a computer; then the diagrams of tool
temperature vs. various cutting parameters were obtained. The
experimental results reveal that the main factors of the increasing
cutting temperature are cutting speed (V ), feed rate ( S ) and depth
of cut ( h ), respectively. It was also determined that simultaneously
change in cutting speed and feed rate has the maximum effect on
increasing cutting temperature.
Abstract: Using steelmaking slag as a raw material, aragonite superstructure product had been synthesized via an indirect CO2 mineral sequestration rout. It mainly involved two separate steps, in which the element of calcium is first selectively leached from steelmaking slag by a novel leaching media consisting of organic solvent Tributyl phosphate (TBP), acetic acid, and ultra-purity water, followed by enhanced carbonation in a separate step for aragonite superstructure production as well as efficiency recovery of leaching media. Based on the different leaching medium employed in the steelmaking slag leaching process, two typical products were collected from the enhanced carbonation step. The products were characterized by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM), respectively. It reveals that the needle-like aragonite crystals self-organized into aragonite superstructure particles including aragonite microspheres as well as dumbbell-like spherical particles, can be obtained from the steelmaking slag with the purity over 99%.
Abstract: In the meantime, there were lots of hardware solutions like products or urban facilities for crime prevention in the public design area. Meanwhile, people have growing interest in public design so by making a village; community design in public design is getting active by the society. The system for crime prevention is actively done by the citizens who created the community. Regarding the social situation, in this project, we saw it as a kind of community design practices and researched about 'how does community design influence Crime prevention?' The purpose of this study is to propose the community design as a way of preventing the crime in the city. First, we found out about the definition, elements and methods of community design by reviewing the theory. And then, this study analyzed the case that was enforced in Seoul and organize the elements and methods of community design. This study can be refer to Public Design based on civil participation and make the community design area contribute to expand the way of solving social problems.
Abstract: In this research work, investigations are carried out on
Continuous Wave (CW) Nd:YAG laser welding system after
preliminary experimentation to understand the influencing parameters
associated with laser welding of AISI 304. The experimental
procedure involves a series of laser welding trials on AISI 304
stainless steel sheets with various combinations of process parameters
like beam power, beam incident angle and beam incident angle. An
industrial 2 kW CW Nd:YAG laser system, available at Welding
Research Institute (WRI), BHEL Tiruchirappalli, is used for
conducting the welding trials for this research. After proper tuning of
laser beam, laser welding experiments are conducted on AISI 304
grade sheets to evaluate the influence of various input parameters on
weld bead geometry i.e. bead width (BW) and depth of penetration
(DOP). From the laser welding results, it is noticed that the beam
power and welding speed are the two influencing parameters on
depth and width of the bead. Three dimensional finite element
simulation of high density heat source have been performed for laser
welding technique using finite element code ANSYS for predicting
the temperature profile of laser beam heat source on AISI 304
stainless steel sheets. The temperature dependent material properties
for AISI 304 stainless steel are taken into account in the simulation,
which has a great influence in computing the temperature profiles.
The latent heat of fusion is considered by the thermal enthalpy of
material for calculation of phase transition problem. A Gaussian
distribution of heat flux using a moving heat source with a conical
shape is used for analyzing the temperature profiles. Experimental
and simulated values for weld bead profiles are analyzed for stainless
steel material for different beam power, welding speed and beam
incident angle. The results obtained from the simulation are
compared with those from the experimental data and it is observed
that the results of numerical analysis (FEM) are in good agreement
with experimental results, with an overall percentage of error
estimated to be within ±6%.
Abstract: In this paper the development of a heat exchanger as a
pilot plant for educational purpose is discussed and the use of neural
network for controlling the process is being presented. The aim of the
study is to highlight the need of a specific Pseudo Random Binary
Sequence (PRBS) to excite a process under control. As the neural
network is a data driven technique, the method for data generation
plays an important role. In light of this a careful experimentation
procedure for data generation was crucial task. Heat exchange is a
complex process, which has a capacity and a time lag as process
elements. The proposed system is a typical pipe-in- pipe type heat
exchanger. The complexity of the system demands careful selection,
proper installation and commissioning. The temperature, flow, and
pressure sensors play a vital role in the control performance. The
final control element used is a pneumatically operated control valve.
While carrying out the experimentation on heat exchanger a welldrafted
procedure is followed giving utmost attention towards safety
of the system. The results obtained are encouraging and revealing
the fact that if the process details are known completely as far as
process parameters are concerned and utilities are well stabilized then
feedback systems are suitable, whereas neural network control
paradigm is useful for the processes with nonlinearity and less
knowledge about process. The implementation of NN control
reinforces the concepts of process control and NN control paradigm.
The result also underlined the importance of excitation signal
typically for that process. Data acquisition, processing, and
presentation in a typical format are the most important parameters
while validating the results.
Abstract: The cyberspace is an instrument through which
internet users could get new experiences. It could contribute to foster
one-s own growth, widening cognitive, creative and communicative
abilities and promoting relationships. In the cyberspace, in fact, it is
possible to create virtual learning communities where internet users
improve their interpersonal sphere, knowledge and skills. The main
element of e-learning is the establishment of online relationships, that
are often collaborative.
Abstract: In the present study, changes of morphology and
mechanical characteristics in the lumbar vertebrae of the
ovariectomised (OVX) rat were investigated. In previous researches,
there were many studies about morphology like volume fraction and
trabecular thickness based on Micro - Computed Tomography (Micro
- CT). However, detecting and tracking long-term changes in the
trabecular bone of the lumbar vertebrae for the OVX rat were few. For
this study, one female Sprague-Dawley rat was used: an OVX rat. The
4th Lumbar of the OVX rat was subjected to in-vivo micro-CT.
Detecting and tracking long-term changes could be investigated in the
trabecular bone of the lumbar vertebrae for an OVX rat using in-vivo
micro-CT. An OVX rat was scanned at week 0 (just before surgery), at
week 4, at week 8, week 16, week 22 and week 56 after surgery. Finite
element (FE) analysis was used to investigate mechanical
characteristics of the lumbar vertebrae for an OVX rat. When the OVX
rat (at week 56) was compared with the OVX rat (at week 0), volume
fraction was decreased by 80% and effective modulus was decreased
by 75%.
Abstract: There are very complex communication systems, as
the multifunction radar, MFAR (Multi-Function Array Radar), where
functions are integrated all together, and simultaneously are
performed the classic functions of tracking and surveillance, as all
the functions related to the communication, countermeasures, and
calibration. All these functions are divided into the tasks to execute.
The task scheduler is a key element of the radar, since it does the
planning and distribution of energy and time resources to be shared
and used by all tasks. This paper presents schedulers based on the use
of multiple queue. Several schedulers have been designed and
studied, and it has been made a comparative analysis of different
performed schedulers. The tests and experiments have been done by
means of system software simulation. Finally a suitable set of radar
characteristics has been selected to evaluate the behavior of the task
scheduler working.