Abstract: Water recycling represents an important challenge for many countries, in particular in countries where this natural resource is rare. On the other hand, in many operations, water is used as a cooling medium, as a high proportion of water consumed in industry is used for cooling purposes. Generally this water is rejected directly to the nature. This reject will cause serious environment damages as well as an important waste of this precious element.. On way to solve these problems is to reuse and recycle this warm water, through the use of natural cooling medium, such as air in a heat exchanger unit, known as a cooling tower. A poor performance, design or reliability of cooling towers will result in lower flow rate of cooling water an increase in the evaporation of water, an hence losses of water and energy. This paper which presents an experimental investigate of thermal and hydraulic performances of a mechanical cooling tower, enables to show that the water evaporation rate, Mev, increases with an increase in the air and water flow rates, as well as inlet water temperature and for fixed air flow rates, the pressure drop (ΔPw/Z) increases with increasing , L, due to the hydrodynamic behavior of the air/water flow.
Abstract: The system is made with main distributed components:
First Level: Industrial Computers placed in Control Room (monitors thermal and electrical processes based on the data provided by the second level); Second Level: PLCs which collects data from process and transmits information on the first level; also takes commands from this level which are further, passed to execution elements from third
level; Third Level: field elements consisting in 3 categories: data collecting elements; data transfer elements from the third level to the second; execution elements which take commands from the second
level PLCs and executes them after which transmits the confirmation of execution to them. The purpose of the automatic functioning is the optimization of the co-generative electrical energy commissioning in the national
energy system and the commissioning of thermal energy to the consumers.
The integrated system treats the functioning of all the equipments and devices as a whole: Gas Turbine Units (GTU); MT 20kV Medium Voltage Station (MVS); 0,4 kV Low Voltage Station (LVS); Main Hot Water Boilers (MHW); Auxiliary Hot Water Boilers (AHW); Gas Compressor Unit (GCU); Thermal Agent Circulation
Pumping Unit (TPU); Water Treating Station (WTS).
Abstract: Buildings are considered as significant part in the
cities, which plays main role in organization and arrangement of city
appearance, which is affects image of that building facades, as an
connective between inner and outer space, have a main role in city
image and they are classified as rich image and poor image by people
evaluation which related to visual architectural and urban elements in
building facades. the buildings in Karimi street , in Lahijan city
where, lies in north of Iran, contain the variety of building's facade
types which, have made a city image in Historical part of Lahijan
city, while reflected the Iranian cities identity. The study attempt to
identify the architectural and urban elements that impression the
image of building facades in historical area, based on public
evaluation. Quantitative method were used and the data was collected
through questionnaire survey, the result presented architectural style,
color, shape, and design evaluated by people as most important factor
which should be understate in future development. in fact, the rich
architectural style with strong design make strong city image as weak
design make poor city image.
Abstract: in dissimilar material joints, failure often occurs
along the interface between two materials due to stress singularity.
Stress distribution and its concentration depend on materials and
geometry of the junction. Inhomogenity of stress distribution at the
interface of junction of two materials with different elastic modules
and stress concentration in this zone are the main factors resulting in
rupture of the junction. Effect of joining angle in the interface of
aluminum-polycarbonate will be discussed in this paper. Computer
simulation and finite element analysis by ABAQUS showed that
convex interfacial joint leads to stress reduction at junction corners in
compare with straight joint. This finding is confirmed by photoelastic
experimental results.
Abstract: The primary objective of the paper is to propose a new method for solving assignment problem under uncertain situation. In the classical assignment problem (AP), zpqdenotes the cost for assigning the qth job to the pth person which is deterministic in nature. Here in some uncertain situation, we have assigned a cost in the form of composite relative degree Fpq instead of and this replaced cost is in the maximization form. In this paper, it has been solved and validated by the two proposed algorithms, a new mathematical formulation of IVIF assignment problem has been presented where the cost has been considered to be an IVIFN and the membership of elements in the set can be explained by positive and negative evidences. To determine the composite relative degree of similarity of IVIFS the concept of similarity measure and the score function is used for validating the solution which is obtained by Composite relative similarity degree method. Further, hypothetical numeric illusion is conducted to clarify the method’s effectiveness and feasibility developed in the study. Finally, conclusion and suggestion for future work are also proposed.
Abstract: The effect of thermally induced stress on the modal
properties of highly elliptical core optical fibers is studied in this
work using a finite element method. The stress analysis is carried out
and anisotropic refractive index change is calculated using both the
conventional plane strain approximation and the generalized plane
strain approach. After considering the stress optical effect, the modal
analysis of the fiber is performed to obtain the solutions of
fundamental and higher order modes. The modal effective index,
modal birefringence, group effective index, group birefringence, and
dispersion of different modes of the fiber are presented. For
propagation properties, it can be seen that the results depend much on
the approach of stress analysis.
Abstract: In this paper, the computation of the electrical field distribution around AC high-voltage lines is demonstrated. The advantages and disadvantages of two different methods are described to evaluate the electrical field quantity. The first method is a seminumerical method using the laws of electrostatic techniques to simulate the two-dimensional electric field under the high-voltage overhead line. The second method which will be discussed is the finite element method (FEM) using specific boundary conditions to compute the two- dimensional electric field distributions in an efficient way.
Abstract: In conventional reliability assessment, the reliability data of system components are treated as crisp values. The collected data have some uncertainties due to errors by human beings/machines or any other sources. These uncertainty factors will limit the understanding of system component failure due to the reason of incomplete data. In these situations, we need to generalize classical methods to fuzzy environment for studying and analyzing the systems of interest. Fuzzy set theory has been proposed to handle such vagueness by generalizing the notion of membership in a set. Essentially, in a Fuzzy Set (FS) each element is associated with a point-value selected from the unit interval [0, 1], which is termed as the grade of membership in the set. A Vague Set (VS), as well as an Intuitionistic Fuzzy Set (IFS), is a further generalization of an FS. Instead of using point-based membership as in FS, interval-based membership is used in VS. The interval-based membership in VS is more expressive in capturing vagueness of data. In the present paper, vague set theory coupled with conventional Lambda-Tau method is presented for reliability analysis of repairable systems. The methodology uses Petri nets (PN) to model the system instead of fault tree because it allows efficient simultaneous generation of minimal cuts and path sets. The presented method is illustrated with the press unit of the paper mill.
Abstract: Solar energy has a major role in renewable energy
resources. Solar Cell as a basement of solar system has attracted lots
of research. To conduct a study about solar energy system, an
authenticated model is required. Diode base PV models are widely
used by researchers. These models are classified based on the number
of diodes used in them. Single and two-diode models are well
studied. Single-diode models may have two, three or four elements.
In this study, these solar cell models are examined and the simulation
results are compared to each other. All PV models are re-designed in
the Matlab/Simulink software and they examined by certain test
conditions and parameters. This paper provides comparative studies
of these models and it tries to compare the simulation results with
manufacturer-s data sheet to investigate model validity and accuracy.
The results show a four- element single-diode model is accurate and
has moderate complexity in contrast to the two-diode model with
higher complexity and accuracy
Abstract: In this paper the fatigue crack initiation location of double shear lap joints, treated by interference fit and bolt clamping, have been investigated both experimentally and numerically. To do so, using the fracture section of available fatigue tested specimens of interference fitted and torque tightened Aluminum 2024-T3 plates, the crack initiation location was determined. The stress distribution attained from the finite element analysis was used to help explain the results observed in the experimental tests. The results showed that the fatigue crack initiation location changes from top and mid plane at the hole edge to somewhere far from the hole edge (stress concentration region) in different combination of clamping force, interference fit size and applied cyclic load ranges. It is worth mentioning that the fatigue crack initiation location affects the fatigue life of the specimens too.
Abstract: Using finite element method (FEM), the elastic
new strain-concentration factor (SNCF) of cylindrical bars
with circumferential flat-bottom groove is studied. This new
SNCF has been defined under triaxial stress state. The
employed specimens have constant groove depth with net
section and gross diameters of 10.0 and 16.7 mm,
respectively. The length of flatness ao has been varied form
0.0 ~12.5 mm to study the elastic SNCF of this type of
geometrical irregularities. The results that the elastic new
SNCF rapidly drops from its elastic value of the groove with
ao = 0.0, i.e. circumferential U-notch, and reaches minimum
value at ao = 2 mm. After that the elastic new SNCF becomes
nearly constant with increasing flatness length (ao). The value
of tensile load at yielding at the groove root increases with
increasing ao. The current results show that severity of the
notch decreases with increasing flatness length ao.
Abstract: Money laundering has been described by many as the lifeblood of crime and is a major threat to the economic and social well-being of societies. It has been recognized that the banking system has long been the central element of money laundering. This is in part due to the complexity and confidentiality of the banking system itself. It is generally accepted that effective anti-money laundering (AML) measures adopted by banks will make it tougher for criminals to get their "dirty money" into the financial system. In fact, for law enforcement agencies, banks are considered to be an important source of valuable information for the detection of money laundering. However, from the banks- perspective, the main reason for their existence is to make as much profits as possible. Hence their cultural and commercial interests are totally distinct from that of the law enforcement authorities. Undoubtedly, AML laws create a major dilemma for banks as they produce a significant shift in the way banks interact with their customers. Furthermore, the implementation of the laws not only creates significant compliance problems for banks, but also has the potential to adversely affect the operations of banks. As such, it is legitimate to ask whether these laws are effective in preventing money launderers from using banks, or whether they simply put an unreasonable burden on banks and their customers. This paper attempts to address these issues and analyze them against the background of the Malaysian AML laws. It must be said that effective coordination between AML regulator and the banking industry is vital to minimize problems faced by the banks and thereby to ensure effective implementation of the laws in combating money laundering.
Abstract: Comparison of two approaches for the simulation of
the dynamic behaviour of a permanent magnet linear actuator is
presented. These are full coupled model, where the electromagnetic
field, electric circuit and mechanical motion problems are solved
simultaneously, and decoupled model, where first a set of static
magnetic filed analysis is carried out and then the electric circuit and
mechanical motion equations are solved employing bi-cubic spline
approximations of the field analysis results. The results show that the
proposed decoupled model is of satisfactory accuracy and gives more
flexibility when the actuator response is required to be estimated for
different external conditions, e.g. external circuit parameters or
mechanical loads.
Abstract: Research in quantum computation is looking for the consequences of having information encoding, processing and communication exploit the laws of quantum physics, i.e. the laws which govern the ultimate knowledge that we have, today, of the foreign world of elementary particles, as described by quantum mechanics. This paper starts with a short survey of the principles which underlie quantum computing, and of some of the major breakthroughs brought by the first ten to fifteen years of research in this domain; quantum algorithms and quantum teleportation are very biefly presented. The next sections are devoted to one among the many directions of current research in the quantum computation paradigm, namely quantum programming languages and their semantics. A few other hot topics and open problems in quantum information processing and communication are mentionned in few words in the concluding remarks, the most difficult of them being the physical implementation of a quantum computer. The interested reader will find a list of useful references at the end of the paper.
Abstract: This paper presents nonlinear elastic dynamic analysis
of 3-D semi-rigid steel frames including geometric and connection
nonlinearities. The geometric nonlinearity is considered by using
stability functions and updating geometric stiffness matrix. The
nonlinear behavior of the steel beam-to-column connection is
considered by using a zero-length independent connection element
comprising of six translational and rotational springs. The nonlinear
dynamic equilibrium equations are solved by the Newmark numerical
integration method. The nonlinear time-history analysis results are
compared with those of previous studies and commercial SAP2000
software to verify the accuracy and efficiency of the proposed
procedure.
Abstract: In this paper, the influencing parameters of a novel
purely mechanical wireless in-mould injection moulding sensor
were investigated. The sensor is capable of detecting the melt
front at predefined locations inside the mould. The sensor comprises
a movable pin which acts as the sensor element generating
structure-borne sound triggered by the passing melt front. Due to
the sensor design, melt pressure is the driving force. For pressure
level measurement during pin movement a pressure transducer
located at the same position as the movable pin. By deriving
a mathematical model for the mechanical movement, dominant
process parameters could be investigated towards their impact
on the melt front detection characteristic. It was found that the
sensor is not affected by the investigated parameters enabling it
for reliable melt front detection. In addition, it could be proved
that the novel sensor is in comparable range to conventional melt
front detection sensors.
Abstract: In this study, a minimal submaximal element of LIT(X) (the lattice of all intuitionistic topologies for X, ordered by inclusion) is determined. Afterwards, a new contractive property, intuitionistic mega-connectedness, is defined. We show that the submaximality and mega-connectedness are not complementary intuitionistic topological invariants by identifying those members of LIT(X) which are intuitionistic mega-connected.
Abstract: Sports Sciences has been historically supported by the positivism idea of science, especially by the mechanistic/reductionist and becomes a field that views experimentation and measurement as the mayor research domains. The disposition to simplify nature and the world by parts has fragmented and reduced the idea of bodyathletes as machine. In this paper we intent to re-think this perception lined by Complexity Theory. We come with the idea of athletes as a reflexive and active being (corporeity-body). Therefore, the construction of a training that considers the cultural, biological, psychological elements regarding the experience of the human corporal movements in a circumspect and responsible way could bring better chances of accomplishment. In the end, we hope to help coaches understand the intrinsic complexity of the body they are training, how better deal with it, and, in the field of a deep globalization among the different types of knowledge, to respect and accepted the peculiarities of knowledge that comprise this area.
Abstract: Natural frequencies and dynamic response of a spur
gear sector are investigated using a two dimensional finite element
model that offers significant advantages for dynamic gear analyses.
The gear teeth are analyzed for different operating speeds. A primary
feature of this modeling is determination of mesh forces using a
detailed contact analysis for each time step as the gears roll through
the mesh. ANSYS software has been used on the proposed model to
find the natural frequencies by Block Lanczos technique and
displacements and dynamic stresses by transient mode super position
method. The effect of rotational speed of the gear on the dynamic
response of gear tooth has been studied and design limits have been
discussed.
Abstract: This study analyzes on the Social Network Game
(SNG), ANIPANG, in order to discover its unique fun elements, so
that suggest new methodologies for development of SNGs. ANIPANG
is the most popular SNG in the South Korea on 2012. Recently, the
game industry is paying close attention to mobile-based SNGs due to
the rapid prevalence of smart-phones and social network services.
However, SNGs are not online games simply. Although the fun of
most online games is the victory through competition with other
players or the game system, the fun of SNG is the communication
through the collaboration with other players. Thus, features of users
and environments of game should be considered for the game industry
and for the fun of SNG to users.