Abstract: The use of amine mixtures employing
methyldiethanolamine (MDEA), monoethanolamine (MEA), and diethanolamine (DEA) have been investigated for a variety of cases
using a process simulation program called HYSYS. The results show that, at high pressures, amine mixtures have little or no advantage in the cases studied. As the pressure is lowered, it becomes more difficult for MDEA to meet residual gas requirements and mixtures can usually improve plant performance. Since the CO2 reaction rate
with the primary and secondary amines is much faster than with
MDEA, the addition of small amounts of primary or secondary amines to an MDEA based solution should greatly improve the overall reaction rate of CO2 with the amine solution. The addition of MEA caused the CO2 to be absorbed more strongly in the upper portion of the column than for MDEA along. On the other hand,
raising the concentration for MEA to 11%wt, CO2 is almost
completely absorbed in the lower portion of the column. The addition of MEA would be most advantageous.
Thus, in areas where MDEA cannot meet the residual gas
requirements, the use of amine mixtures can usually improve the plant
performance.
Abstract: Lignocellulosic materials are considered the most
abundant renewable resource available for the Bioethanol
Production. Water Hyacinth is one of potential raw material of the
world-s worst aquatic plant as a feedstock to produce Bioethanol.
The purposed this research is obtain reduced of matter for
biodegradation lignin in Biological pretreatment with White Rot
Fungi eg. Phanerochaete Chrysosporium using Solid state
Fermentation methods. Phanerochaete Chrysosporium is known to
have the best ability to degraded lignin, but simultaneously it can also
degraded cellulose and hemicelulose. During 8 weeks incubation,
water hyacinth occurred loss of weight reached 34,67%, while loss
of lignin reached 67,21%, loss of cellulose reached 11,01% and loss
of hemicellulose reached 36,56%. The kinetic of losses lignin using
regression linear plot, the results is obtained constant rate (k) of
reduction lignin is -0.1053 and the equation of reduction of lignin
is y = wo - 0, 1.53 x
Abstract: This paper present a new way to find the aerodynamic
characteristic equation of missile for the numerical trajectories
prediction more accurate. The goal is to obtain the polynomial
equation based on two missile characteristic parameters, angle of
attack (α ) and flight speed (ν ). First, the understudied missile is
modeled and used for flow computational model to compute
aerodynamic force and moment. Assume that performance range of
understudied missile where range -10< α
Abstract: It is estimated that the total cost of abnormal
conditions to US process industries is around $20 billion dollars in
annual losses. The hydrotreatment (HDT) of diesel fuel in petroleum
refineries is a conversion process that leads to high profitable
economical returns. However, this is a difficult process to control
because it is operated continuously, with high hydrogen pressures
and it is also subject to disturbances in feed properties and catalyst
performance. So, the automatic detection of fault and diagnosis plays
an important role in this context. In this work, a hybrid approach
based on neural networks together with a pos-processing
classification algorithm is used to detect faults in a simulated HDT
unit. Nine classes (8 faults and the normal operation) were correctly
classified using the proposed approach in a maximum time of 5
minutes, based on on-line data process measurements.
Abstract: Calcium is very important for communication among
the neurons. It is vital in a number of cell processes such as secretion,
cell movement, cell differentiation. To reduce the system of reactiondiffusion
equations of [Ca2+] into a single equation, two theories
have been proposed one is excess buffer approximation (EBA) other
is rapid buffer approximation (RBA). The RBA is more realistic than
the EBA as it considers both the mobile and stationary endogenous
buffers. It is valid near the mouth of the channel. In this work we have
studied the effects of different types of buffers on calcium diffusion
under RBA. The novel thing studied is the effect of sodium ions on
calcium diffusion. The model has been made realistic by considering
factors such as variable [Ca2+], [Na+] sources, sodium-calcium
exchange protein(NCX), Sarcolemmal Calcium ATPase pump. The
proposed mathematical leads to a system of partial differential equations
which has been solved numerically to study the relationships
between different parameters such as buffer concentration, buffer
disassociation rate, calcium permeability. We have used Forward
Time Centred Space (FTCS) approach to solve the system of partial
differential equations.
Abstract: The present work presents the extraction of copper(II)
from sulphuric acid solutions with Sodium diethyldithiocarbamate
(SDDT), and six different organic diluents: Dichloromethane,
Chloroform, Carbon tetrachloride, Toluene, xylene and Cyclohexane,
were tested. The pair SDDT/Chloroform showed to be the most
selective in removing the copper cations, and hence was considered
throughout the experimental study.
The effects of operating parameters such as the initial concentration
of the extracting agent, the agitation time, the agitation speed and the
acid concentration were considered.
For an initial concentration of Cu (II) of 63 ppm in a 0.5 M sulphuric
acid solution, both with a mass of the extracting agent of 20 mg, an
extraction percentage of about 97.8 % and a distribution coefficient
of 44.42 were obtained, respectively, confirming the performance
of the SDDT-Chloroform pair.
Abstract: Mycophenolic acid “MPA" is a secondary metabolite
of Penicillium bervicompactum with antibiotic and
immunosuppressive properties. In this study, fermentation process
was established for production of mycophenolic acid by Penicillium
bervicompactum MUCL 19011 in shake flask. The maximum MPA
production, product yield and productivity were 1.379 g/L, 18.6 mg/g
glucose and 4.9 mg/L.h respectively. Glucose consumption, biomass
and MPA production profiles were investigated during fermentation
time. It was found that MPA production starts approximately after
180 hours and reaches to a maximum at 280 h. In the next step, the
effects of methionine and acetate concentrations on MPA production
were evaluated. Maximum MPA production, product yield and
productivity (1.763 g/L, 23.8 mg/g glucose and 6.30 mg/L. h
respectively) were obtained with using 2.5 g/L methionine in culture
medium. Further addition of methionine had not more positive effect
on MPA production. Finally, results showed that the addition of
acetate to the culture medium had not any observable effect on MPA
production.
Abstract: The objective of this work is to show a procedure for
mesh generation in a fluidized bed using large eddy simulations
(LES) of a filtered two-fluid model. The experimental data were
obtained by [1] in a laboratory fluidized bed. Results show that it is
possible to use mesh with less cells as compared to RANS turbulence
model with granular kinetic theory flow (KTGF). Also, the numerical
results validate the experimental data near wall of the bed, which
cannot be predicted by RANS.model.
Abstract: The remediation of water resources pollution in
developing countries requires the application of alternative
sustainable cheaper and efficient end-of-pipe wastewater treatment
technologies. The feasibility of use of South African cheap and
abundant pine tree (Pinus patula) sawdust for development of lowcost
AC of comparable quality to expensive commercial ACs in the
abatement of water pollution was investigated. AC was developed at
optimized two-stage N2-superheated steam activation conditions in a
fixed bed reactor, and characterized for proximate and ultimate
properties, N2-BET surface area, pore size distribution, SEM, pHPZC
and FTIR. The sawdust pyrolysis activation energy was evaluated by
TGA. Results indicated that the chars prepared at 800oC and 2hrs
were suitable for development of better quality AC at 800oC and 47%
burn-off having BET surface area (1086m2/g), micropore volume
(0.26cm3/g), and mesopore volume (0.43cm3/g) comparable to
expensive commercial ACs, and suitable for water contaminants
removal. The developed AC showed basic surface functionality at
pHPZC at 10.3, and a phenol adsorption capacity that was higher than
that of commercial Norit (RO 0.8) AC. Thus, it is feasible to develop
better quality low-cost AC from (Pinus patula) sawdust using twostage
N2-steam activation in fixed-bed reactor.
Abstract: The systematic manipulations of shapes and sizes of
inorganic compounds greatly benefit the various application fields
including optics, magnetic, electronics, catalysis and medicine.
However shape control has been much more difficult to achieve.
Hence exploration of novel method for the preparation of differently
shaped nanoparticles is challenging research area. II-VI group of
semiconductor cadmium sulphide (CdS) nanostructure with different
morphologies (such as, acicular like, mesoporous, spherical shapes)
and of crystallite sizes vary from 11 to 16 nm were successfully
synthesized by chemical aqueous precipitation of Cd2+ ions with
homogeneously released S2- ions from decomposition of cadmium
sulphate (CdSO4) and thioacetamide (CH3CSNH2) by annealing at
different radiations (microwave, ultrasonic and sunlight) with matter
and systematic research has been done for various factors affecting
the controlled growth rate of CdS nanoparticles. The obtained
nanomaterials have been characterized by X-ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FTIR),
Thermogravometric (DSC-TGA) analysis and Scanning Electron
Microscopy (SEM). The result indicates that on increasing the
reaction time particle size increases but on increasing the molar ratios
grain size decreases.
Abstract: Sulfide ion (S2-) is one of the most important ions to be
monitored due to its high toxicity, especially for aquatic organisms. In
this work, [Ca(2,2'-bipyridine)3]2+-intercalated montmorillonite was
prepared and used as a sensor to construct a potentiometric electrode to
measure sulfide ion in solution. The formation of [Ca(2,2'-
bipyridine)3]2+ in montmorillonite was confirmed by Fourier Transform
Infrared spectra. The electrode worked well at pH 4-12 and 4-10 in
sulfide solution 10-2 M and 10-3 M, respectively, in terms of Nernstian
slope. The sensor gave good precision and low cost.
Abstract: The consumption of lactose in acid cheese whey
anaerobic fermentation process under fed-batch conditions was
studied. During fermentation for 100 hours the biogas production
(CO2 and CH4) was analyzed online. Among the standard analyses
FT-IR spectroscopy was used to follow the consumption of lactose by
bacteria. The absorption bands at 990, 894 and 787 cm-1 in the 2nd
derivative spectra were shown to be characteristic for lactose and
were used to follow the lactose conversion. It was shown that acid
cheese whey lactose was converted by bacteria in first 7 hours. In the
spectra of 17, 18 and 95 hour fermentation samples lactose was not
identified and these results correlated with the HPLC data.
Abstract: Chicken fat was employed as a feedstock for
producing of biodiesel by trasesterification reaction with methanol
and alkali catalyst (KOH). In this study chicken fat biodiesel with
1.4% free fatty acid, methanol and various amount of potassium
hydroxide for 2 hour were studied. The progression of reaction and
conversion of triglycerides to methyl ester were checked by IR
spectrum method.
Abstract: Biofuels, like biobutanol, have been recognized for
being renewable and sustainable fuels which can be produced from
lignocellulosic biomass. To convert lignocellulosic biomass to
biofuel, pretreatment process is an important step to remove
hemicelluloses and lignin to improve enzymatic hydrolysis. Dilute
acid pretreatment has been successful developed for pretreatment of
corncobs and the optimum conditions of dilute sulfuric and
phosphoric acid pretreatment were obtained at 120 °C for 5 min with
15:1 liquid to solid ratio and 140 °C for 10 min with 10:1 liquid to
solid ratio, respectively. The result shows that both of acid
pretreatments gave the content of total sugar approximately 34–35
g/l. In case of inhibitor content (furfural), phosphoric acid
pretreatment gives higher than sulfuric acid pretreatment.
Characterizations of corncobs after pretreatment indicate that both of
acid pretreatments can improve enzymatic accessibility and the better
results present in corncobs pretreated with sulfuric acid in term of
surface area, crystallinity, and composition analysis.
Abstract: Solution for the complete removal of carbon
monoxide from the exhaust gases still poses a challenge to the
researchers and this problem is still under development. Modeling for
reduction of carbon monoxide is carried out using heterogeneous
reaction using low cost non-noble metal based catalysts for the
purpose of controlling emissions released to the atmosphere. A
simple one-dimensional model was developed for the monolith using
hopcalite catalyst. The converter is assumed to be an adiabatic
monolith operating under warm-up conditions. The effect of inlet gas
temperatures and catalyst loading on carbon monoxide reduction
during cold start period in the converter is analysed.
Abstract: The present work is concerned with sulfidation of Cu,
Zn and Ni containing plating wastewater with CaS. The sulfidation
experiments were carried out at a room temperature by adding solid
CaS to simulated metal solution containing either single-metal of Ni,
Zn and Cu, or Ni-Zn-Cu mixture. At first, the experiments were
conducted without pH adjustment and it was found that the complete
sulfidation of Zn and Ni was achieved at an equimolar ratio of CaS to a
particular metal. However, in the case of Cu, a complete copper
sulfidation was achieved at CaS to Cu molar ratio of about 2. In the
case of the selective sulfidation, a simulated plating solution
containing Cu, Zn and Ni at the concentration of 100 mg/dm3 was
treated with CaS under various pH conditions. As a result, selective
precipitation of metal sulfides was achieved by a sulfidation treatment
at different pH values. Further, the precipitation agents of NaOH,
Na2S and CaS were compared in terms of the average specific
filtration resistance and compressibility coefficients of metal sulfide
slurry. Consequently, based on the lowest filtration parameters of the
produced metal sulfides, it was concluded that CaS was the most
effective precipitation agent for separation and recovery of Cu, Zn and
Ni.
Abstract: Biomass is becoming a large renewable resource for
power generation; it is involved in higher frequency in
environmentally clean processes, and even it is used for biofuels
preparation. On the other hand, hydrogen – other energy source – can
be produced in a variety of methods including gasification of
biomass. In this study, the production of hydrogen by gasification of
biomass waste is examined. This work explores the production of a
gaseous mixture with high power potential from Amazonas´ specie
known as copoazu, using a counter-flow fixed-bed bioreactor.
Abstract: In this paper, the Lennard -Jones potential is applied
to molecules of liquid argon as well as its vapor and platinum as solid
surface in order to perform a non-equilibrium molecular dynamics
simulation to study the microscopic aspects of liquid-vapor-solid
interactions. The channel is periodic in x and y directions and along z
direction it is bounded by atomic walls. It was found that density of
the liquids near the solid walls fluctuated greatly and that the
structure was more like a solid than a liquid. This indicates that the
interactions of solid and liquid molecules are very strong. The
resultant surface tension, liquid density and vapor density are found
to be well predicted when compared with the experimental data for
argon. Liquid and vapor densities were found to depend on the cutoff
radius which induces the use of P3M (particle-particle particle-mesh)
method which was implemented for evaluation of force and surface
tension.
Abstract: A method to determine experimentally the melting
rate, rm, and the heat transfer coefficients, αv (W/(m3K)), at
convective melting in a fixed bed of particles under adiabatic regime
is established in this paper. The method lies in the determining of the
melting rate by measuring the fixed bed height in time. Experimental
values of rm, α and α v were determined using cylindrical particles of
ice (d = 6.8 mm, h = 5.5 mm) and, as a melting agent, aqueous NaCl
solution with a temperature of 283 K at different values of the liquid
flow rate (11.63·10-6, 28.83·10-6, 38.83·10-6 m3/s).
Our experimental results were compared with those existing in
literature being noticed a good agreement for Re values higher than
50.
Abstract: Natural gas flow contains undesirable solid particles,
liquid condensation, and/or oil droplets and requires reliable
removing equipment to perform filtration. Recent natural gas
processing applications are demanded compactness and reliability of
process equipment. Since conventional means are sophisticated in
design, poor in efficiency, and continue lacking robust, a supersonic
nozzle has been introduced as an alternative means to meet such
demands.
A 3-D Convergent-Divergent Nozzle is simulated using
commercial Code for pressure ratio (NPR) varies from 1.2 to 2. Six
different shapes of nozzle are numerically examined to illustrate the
position of shock-wave as such spot could be considered as a
benchmark of particle separation. Rectangle, triangle, circular,
elliptical, pentagon, and hexagon nozzles are simulated using Fluent
Code with all have same cross-sectional area.
The simple one-dimensional inviscid theory does not describe the
actual features of fluid flow precisely as it ignores the impact of
nozzle configuration on the flow properties. CFD Simulation results,
however, show that nozzle geometry influences the flow structures
including location of shock wave.
The CFD analysis predicts shock appearance when p01/pa>1.2 for
almost all geometry and locates at the lower area ratio (Ae/At).
Simulation results showed that shock wave in Elliptical nozzle has
the farthest distance from the throat among the others at relatively
small NPR. As NPR increases, hexagon would be the farthest. The
numerical result is compared with available experimental data and
has shown good agreement in terms of shock location and flow
structure.