Abstract: This paper presents an analytical solution to get a reliable estimation of the hydrodynamic pressure on gravity dams induced by vertical component earthquake when solving the fluid and dam interaction problem. Presented analytical technique is presented for calculation of earthquake-induced hydrodynamic pressure in the reservoir of gravity dams allowing for water compressibility and wave absorption at the reservoir bottom. This new analytical solution can take into account the effect of bottom material on seismic response of gravity dams. It is concluded that because the vertical component of ground motion causes significant hydrodynamic forces in the horizontal direction on a vertical upstream face, responses to the vertical component of ground motion are of special importance in analysis of concrete gravity dams subjected to earthquakes.
Abstract: This paper presents the study of a variable speed wind
energy conversion system based on a Doubly Fed Induction Generator
(DFIG) based on a sliding mode control applied to achieve control of
active and reactive powers exchanged between the stator of the DFIG
and the grid to ensure a Maximum Power Point Tracking (MPPT) of
a wind energy conversion system. The proposed control algorithm is
applied to a DFIG whose stator is directly connected to the grid and
the rotor is connected to the PWM converter. To extract a maximum
of power, the rotor side converter is controlled by using a stator
flux-oriented strategy. The created decoupling control between active
and reactive stator power allows keeping the power factor close to
unity. Simulation results show that the wind turbine can operate at
its optimum energy for a wide range of wind speed.
Abstract: The systematic manipulations of shapes and sizes of
inorganic compounds greatly benefit the various application fields
including optics, magnetic, electronics, catalysis and medicine.
However shape control has been much more difficult to achieve.
Hence exploration of novel method for the preparation of differently
shaped nanoparticles is challenging research area. II-VI group of
semiconductor cadmium sulphide (CdS) nanostructure with different
morphologies (such as, acicular like, mesoporous, spherical shapes)
and of crystallite sizes vary from 11 to 16 nm were successfully
synthesized by chemical aqueous precipitation of Cd2+ ions with
homogeneously released S2- ions from decomposition of cadmium
sulphate (CdSO4) and thioacetamide (CH3CSNH2) by annealing at
different radiations (microwave, ultrasonic and sunlight) with matter
and systematic research has been done for various factors affecting
the controlled growth rate of CdS nanoparticles. The obtained
nanomaterials have been characterized by X-ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FTIR),
Thermogravometric (DSC-TGA) analysis and Scanning Electron
Microscopy (SEM). The result indicates that on increasing the
reaction time particle size increases but on increasing the molar ratios
grain size decreases.
Abstract: Social media has led to paradigm shifts in ways
people work and do business, interact and socialize, learn and obtain
knowledge. So much so that social media has established itself as an
important spatial extension of this nation-s historicity and challenges.
Regardless of the enabling reputation and recommendation features
through social networks embedded in the social media system, the
overflow of broadcasted and publicized media contents turns the
table around from engendering trust to doubting the trust system.
When the trust is at doubt, the effects include deactivation of
accounts and creation of multiple profiles, which lead to the overflow
of 'ghost' contents (i.e. “the abundance of abandoned ships"). In
most literature, the study of trust can be related to culture; hence the
difference between Western-s “openness" and Eastern-s “blue-chip"
concepts in networking and relationships. From a survey on issues
and challenges among Malaysian social media users, 'authenticity'
emerges as one of the main factors that causes and is caused by other
factors. The other issue that has surfaced is credibility either in terms
of message/content and source. Another is the quality of the
knowledge that is shared. This paper explores the terrains of this
critical space which in recent years has been dominated increasingly
by, arguably, social networks embedded in the social media system,
the overflow of broadcasted and publicized media content.
Abstract: Most high-performance ac drives utilize a current
controller. The controller switches a voltage source inverter (VSI)
such that the motor current follows a set of reference current
waveforms. Fixed-band hysteresis (FBH) current control has been
widely used for the PWM inverter. We want to apply the same
controller for the PWM AC chopper. The aims of the controller is to
optimize the harmonic content at both input and output sides, while
maintaining acceptable losses in the ac chopper and to control in
wide range the fundamental output voltage. Fixed band controller has
been simulated and analyzed for a single-phase AC chopper and are
easily extended to three-phase systems. Simulation confirmed the
advantages and the excellent performance of the modulation method
applied for the AC chopper.
Abstract: In this paper the combination of thermal oxidation and
electrochemical anodizing processes is used to produce titanium
oxide layers. The response of titanium alloy Ti6Al4V to oxidation
processes at various temperatures and electrochemical anodizing in
various voltages are investigated. Scanning electron microscopy
(SEM); X-Ray Diffraction (XRD) and porosity determination have
been used to characterize the oxide layer thickness, surface
morphology, oxide layer-substrate adhesion and porosity. In the first
experiment, samples modified by thermal oxidation process then
followed by electrochemical anodizing. Second experiment consists
of surfaces modified by electrochemical anodizing process and then
followed by thermal oxidation. The first method shows better
properties than other one. In second experiment, Surfaces modified
were achieved by thicker and more adherent thick oxide layers on
titanium surface. The existence of an electrochemical anodized oxide
layer did not improve the adhesion of thermal oxide layer. The high
temperature, thermal formation of an oxide layer leads to a coarse
oxide grain morphology and a complete oxidative particle. In
addition, in high temperature oxidation porosity content is increased.
The oxide layer of thermal oxidation and electrochemical anodizing
processes; on Ti–6Al–4V substrate was covered with different
colored oxide layers.
Abstract: Machine Translation (MT 3) of English text to its Urdu equivalent is a difficult challenge. Lot of attempts has been made, but a few limited solutions are provided till now. We present a direct approach, using an expert system to translate English text into its equivalent Urdu, using The Unicode Standard, Version 4.0 (ISBN 0-321-18578-1) Range: 0600–06FF. The expert system works with a knowledge base that contains grammatical patterns of English and Urdu, as well as a tense and gender-aware dictionary of Urdu words (with their English equivalents).
Abstract: Date palm (Phoenix dactylifera L.) seeds are waste streams which are considered a major problem to the food industry. They contain potentially useful protein (10-15% of the whole date-s weight). Global production, industrialisation and utilisation of dates are increasing steadily. The worldwide production of date palm fruit has increased from 1.8 million tons in 1961 to 6.9 million tons in 2005, thus from the global production of dates are almost 800.000 tonnes of date palm seeds are not currently used [1]. The current study was carried out to convert the date palm seeds into useful protein powder. Compositional analysis showed that the seeds were rich in protein and fat 5.64 and 8.14% respectively. We used several laboratory scale methods to extract proteins from seed to produce a high protein powder. These methods included simple acid or alkali extraction, with or without ultrafiltration and phenol trichloroacetic acid with acetone precipitation (Ph/TCA method). The highest protein content powder (68%) was obtained by Ph/TCA method with yield of material (44%) whereas; the use of just alkali extraction gave the lowest protein content of 8%, and a yield of 32%.
Abstract: In this article, we propose a new surgical device for
circumferentially excision of high anal fistulas in a minimally
invasive manner. The new apparatus works on the basis of axially
rotating and moving a tubular blade along a fistulous tract
straightened using a rigid straight guidewire. As the blade moves
along the tract, its sharp circular cutting edge circumferentially
separates approximately 2.25 mm thickness of tract encircling the
rigid guidewire. We used the new set to excise two anal fistulas in a
62-year-old male patient, an extrasphincteric type and a long tract
with no internal opening. With regard to the results of this test, the
new device can be considered as a sphincter preserving mechanism
for treatment of high anal fistulas. Consequently, a major reduction
in the risk of fecal incontinence, recurrence rate, convalescence
period and patient morbidity may be achieved using the new device
for treatment of fistula-in-ano.
Abstract: Text categorization is the problem of classifying text documents into a set of predefined classes. After a preprocessing step the documents are typically represented as large sparse vectors. When training classifiers on large collections of documents, both the time and memory restrictions can be quite prohibitive. This justifies the application of features selection methods to reduce the dimensionality of the document-representation vector. Four feature selection methods are evaluated: Random Selection, Information Gain (IG), Support Vector Machine (called SVM_FS) and Genetic Algorithm with SVM (GA_FS). We showed that the best results were obtained with SVM_FS and GA_FS methods for a relatively small dimension of the features vector comparative with the IG method that involves longer vectors, for quite similar classification accuracies. Also we present a novel method to better correlate SVM kernel-s parameters (Polynomial or Gaussian kernel).
Abstract: It is well recognized that the green house gases such
as Chlorofluoro Carbon (CFC), CH4, CO2 etc. are responsible
directly or indirectly for the increase in the average global temperature
of the Earth. The presence of CFC is responsible for
the depletion of ozone concentration in the atmosphere due to
which the heat accompanied with the sun rays are less absorbed
causing increase in the atmospheric temperature of the Earth. The
gases like CH4 and CO2 are also responsible for the increase in
the atmospheric temperature. The increase in the temperature level
directly or indirectly affects the dynamics of interacting species
systems. Therefore, in this paper a mathematical model is proposed
and analysed using stability theory to asses the effects of increasing
temperature due to greenhouse gases on the survival or extinction of
populations in a prey-predator system. A threshold value in terms
of a stress parameter is obtained which determines the extinction or
existence of populations in the underlying system.
Abstract: This study focuses on examining why the range of
experience with respect to HIV infection is so diverse, especially in
regard to the latency period. An agent-based approach in modelling
the infection is used to extract high-level behaviour which cannot be
obtained analytically from the set of interaction rules at the cellular
level. A prototype model encompasses local variation in baseline
properties, contributing to the individual disease experience, and is
included in a network which mimics the chain of lymph nodes. The
model also accounts for stochastic events such as viral mutations.
The size and complexity of the model require major computational
effort and parallelisation methods are used.
Abstract: Groundlessness of application probability-statistic methods are especially shown at an early stage of the aviation GTE technical condition diagnosing, when the volume of the information has property of the fuzzy, limitations, uncertainty and efficiency of application of new technology Soft computing at these diagnosing stages by using the fuzzy logic and neural networks methods. It is made training with high accuracy of multiple linear and nonlinear models (the regression equations) received on the statistical fuzzy data basis. At the information sufficiency it is offered to use recurrent algorithm of aviation GTE technical condition identification on measurements of input and output parameters of the multiple linear and nonlinear generalized models at presence of noise measured (the new recursive least squares method (LSM)). As application of the given technique the estimation of the new operating aviation engine D30KU-154 technical condition at height H=10600 m was made.
Abstract: A Web-based learning tool, the Learn IN Context
(LINC) system, designed and being used in some institution-s
courses in mixed-mode learning, is presented in this paper. This
mode combines face-to-face and distance approaches to education.
LINC can achieve both collaborative and competitive learning. In
order to provide both learners and tutors with a more natural way to
interact with e-learning applications, a conversational interface has
been included in LINC. Hence, the components and essential features
of LINC+, the voice enhanced version of LINC, are described. We
report evaluation experiments of LINC/LINC+ in a real use context
of a computer programming course taught at the Université de
Moncton (Canada). The findings show that when the learning
material is delivered in the form of a collaborative and voice-enabled
presentation, the majority of learners seem to be satisfied with this
new media, and confirm that it does not negatively affect their
cognitive load.
Abstract: In present days the area of data migration is very topical. Current tools for data migration in the area of relational database have several disadvantages that are presented in this paper. We propose a methodology for data migration of the database tables and their data between various types of relational database systems (RDBMS). The proposed methodology contains an expert system. The expert system contains a knowledge base that is composed of IFTHEN rules and based on the input data suggests appropriate data types of columns of database tables. The proposed tool, which contains an expert system, also includes the possibility of optimizing the data types in the target RDBMS database tables based on processed data of the source RDBMS database tables. The proposed expert system is shown on data migration of selected database of the source RDBMS to the target RDBMS.
Abstract: As the majority of faults are found in a few of its modules so there is a need to investigate the modules that are affected severely as compared to other modules and proper maintenance need to be done on time especially for the critical applications. In this paper, we have explored the different predictor models to NASA-s public domain defect dataset coded in Perl programming language. Different machine learning algorithms belonging to the different learner categories of the WEKA project including Mamdani Based Fuzzy Inference System and Neuro-fuzzy based system have been evaluated for the modeling of maintenance severity or impact of fault severity. The results are recorded in terms of Accuracy, Mean Absolute Error (MAE) and Root Mean Squared Error (RMSE). The results show that Neuro-fuzzy based model provides relatively better prediction accuracy as compared to other models and hence, can be used for the maintenance severity prediction of the software.
Abstract: Traditionally, Yemini Sidr honey has been reported to
cure liver problems, stomach ulcers, and respiratory disorders. In this
experiment, we evaluated Yemeni Sidr honey for its ability to protect
inflammations caused by acetic acid and formalin -induced writhing,
carrageenan and histamine-induced paw oedema in experimental rat
model. Hyperpyrexia, membrane stabilizing activity, and
phytochemical screening of the honey was also examined. Yemini
Sidr Honey at (100, 200 and 500 mg/kg) exhibited a concentration
dependant inhibition of acetic acid induced and formalin induced
writhing, paw oedema induced by carrageenan & histamine, and
hyperpyrexia induced by brewer's yeast, it also inhibited membrane
stabilizing activity. Phytochemical screenings of the honey reveal the
presence of flavonoids, steroid, alkaloids, saponins and tannins. This
study suggested that Yemeni Sidr honey possess very strong antiinflammatory,
analgesic and antipyretic effects and these effects
would be a result of the phytochemicals present.
Abstract: Leonotisleonurus a shrub indigenous to Southern
Africa is widely used in traditional medicine to treat a variety of
conditions ranging from skin diseases and cough to epileptic fits and
‘heart problems’. Studies on the aqueous extract of the leaves have
indicated cycloxegenase enzyme inhibitory activity and an
antihypertensive effect.
Five methanol leaf extract fractions (MLEa - MLEe) of L.
leonurus were tested on anaesthetized normotensive male Wistar rats
(AWR) and isolated perfused working rat hearts (IWH). Fraction
MLEc (0.01mg/kg – 0.05mg/kg) induced significant increases in BP
and HR in AWR and positive chronotropic and inotropic effects in
IWH (1.0mg/ml – 5.0mg/ml). Pre-administration of atenolol
(2.0mg/kg) and prazosin (60μg/kg) significantly inhibited MLEc
effect on HR and MAP respectively in vivo, while atenolol
(7.0mg/ml) pre-perfusion significantly inhibited MLEc effect in vitro.
The hypertensive effect of MLEc is probably via β1agonism.
Results also indicate the presence of multiple cardioactive
compounds in L. leonurus.
Abstract: A Positron Emission Tomography (PET) is a radioisotope imaging technique that illustrates the organs and the metabolisms of the human body. This technique is based on the simultaneous detection of 511 keV annihilation photons, annihilated as a result of electrons annihilating positrons that radiate from positron-emitting radioisotopes that enter biological active molecules in the body. This study was conducted on ten patients in an effort to conduct patient-related experimental studies. Dosage monitoring for the bladder, which was the organ that received the highest dose during PET applications, was conducted for 24 hours. Assessment based on measuring urination activities after injecting patients was also a part of this study. The MIRD method was used to conduct dosage calculations for results obtained from experimental studies. Results obtained experimentally and theoretically were assessed comparatively.
Abstract: Academic digital libraries emerged as a result of advances in computing and information systems technologies, and had been introduced in universities and to public. As results, moving in parallel with current technology in learning and researching environment indeed offers myriad of advantages especially to students and academicians, as well as researchers. This is due to dramatic changes in learning environment through the use of digital library system which giving spectacular impact on these societies- way of performing their study/research. This paper presents a survey of current criteria for evaluating academic digital libraries- performance. The goal is to discuss criteria being applied so far for academic digital libraries evaluation in the context of user-centered design. Although this paper does not comprehensively take into account all previous researches in evaluating academic digital libraries but at least it can be a guide in understanding the evaluation criteria being widely applied.