Abstract: The main objective of this paper is to determine the
isolated effect of silica fume on tensile, compressive and flexure strengths on high strength lightweight concrete. Many experiments
were carried out by replacing cement with different percentages of silica fume at different constant water-binder ratio keeping other mix
design variables constant. The silica fume was replaced by 0%, 5%,
10%, 15%, 20% and 25% for a water-binder ratios ranging from 0.26
to 0.42. For all mixes, split tensile, compressive and flexure strengths
were determined at 28 days. The results showed that the tensile, compressive and flexure strengths increased with silica fume incorporation but the optimum replacement percentage is not
constant because it depends on the water–cementitious material (w/cm) ratio of the mix. Based on the results, a relationship between
split tensile, compressive and flexure strengths of silica fume concrete was developed using statistical methods.
Abstract: A feed-forward, back-propagation Artificial Neural
Network (ANN) model has been used to forecast the occurrences of
wastewater overflows in a combined sewerage reticulation system.
This approach was tested to evaluate its applicability as a method
alternative to the common practice of developing a complete
conceptual, mathematical hydrological-hydraulic model for the
sewerage system to enable such forecasts. The ANN approach
obviates the need for a-priori understanding and representation of the
underlying hydrological hydraulic phenomena in mathematical terms
but enables learning the characteristics of a sewer overflow from the
historical data.
The performance of the standard feed-forward, back-propagation
of error algorithm was enhanced by a modified data normalizing
technique that enabled the ANN model to extrapolate into the
territory that was unseen by the training data. The algorithm and the
data normalizing method are presented along with the ANN model
output results that indicate a good accuracy in the forecasted sewer
overflow rates. However, it was revealed that the accurate
forecasting of the overflow rates are heavily dependent on the
availability of a real-time flow monitoring at the overflow structure
to provide antecedent flow rate data. The ability of the ANN to
forecast the overflow rates without the antecedent flow rates (as is
the case with traditional conceptual reticulation models) was found to
be quite poor.
Abstract: The utilization of renewable energy sources in electric
power systems is increasing quickly because of public apprehensions
for unpleasant environmental impacts and increase in the energy
costs involved with the use of conventional energy sources. Despite
the application of these energy sources can considerably diminish the
system fuel costs, they can also have significant influence on the
system reliability. Therefore an appropriate combination of the
system reliability indices level and capital investment costs of system
is vital. This paper presents a hybrid wind/photovoltaic plant, with
the aim of supplying IEEE reliability test system load pattern while
the plant capital investment costs is minimized by applying a hybrid
particle swarm optimization (PSO) / harmony search (HS) approach,
and the system fulfills the appropriate level of reliability.
Abstract: Medical imaging uses the advantage of digital
technology in imaging and teleradiology. In teleradiology systems
large amount of data is acquired, stored and transmitted. A major
technology that may help to solve the problems associated with the
massive data storage and data transfer capacity is data compression
and decompression. There are many methods of image compression
available. They are classified as lossless and lossy compression
methods. In lossy compression method the decompressed image
contains some distortion. Fractal image compression (FIC) is a lossy
compression method. In fractal image compression an image is
coded as a set of contractive transformations in a complete metric
space. The set of contractive transformations is guaranteed to
produce an approximation to the original image. In this paper FIC is
achieved by PIFS using quadtree partitioning. PIFS is applied on
different images like , Ultrasound, CT Scan, Angiogram, X-ray,
Mammograms. In each modality approximately twenty images are
considered and the average values of compression ratio and PSNR
values are arrived. In this method of fractal encoding, the
parameter, tolerance factor Tmax, is varied from 1 to 10, keeping the
other standard parameters constant. For all modalities of images the
compression ratio and Peak Signal to Noise Ratio (PSNR) are
computed and studied. The quality of the decompressed image is
arrived by PSNR values. From the results it is observed that the
compression ratio increases with the tolerance factor and
mammogram has the highest compression ratio. The quality of the
image is not degraded upto an optimum value of tolerance factor,
Tmax, equal to 8, because of the properties of fractal compression.
Abstract: Drying characteristics of rough rice (variety of lenjan) with an initial moisture content of 25% dry basis (db) was studied in a hot air dryer assisted by infrared heating. Three arrival air temperatures (30, 40 and 500C) and four infrared radiation intensities (0, 0.2 , 0.4 and 0.6 W/cm2) and three arrival air speeds (0.1, 0.15 and 0.2 m.s-1) were studied. Bending strength of brown rice kernel, percentage of cracked kernels and time of drying were measured and evaluated. The results showed that increasing the drying arrival air temperature and radiation intensity of infrared resulted decrease in drying time. High bending strength and low percentage of cracked kernel was obtained when paddy was dried by hot air assisted infrared dryer. Between this factors and their interactive effect were a significant difference (p
Abstract: Giving birth is a natural process and most women have to go through it. Gynecologist or Midwife usually uses the leg holder to position the cervix in the stitching process. In some part of rural areas in Indonesia, the labor process normally being done at homes by calling in a midwife or gynecologist. The facilities for this kind of labor process is not yet sufficient, as the use of leg holder supposedly on the obstetric bed. The reality is that it is impossible to bring in the obstetric bed to the patient-s house at the time they call for giving birth or the time when the stitching of the cervix need to be done. This research is redesigning the leg holder through Biomechanics and ergonomic approaches to obtain the optimal design which is suitable to the user of a developing country such as Indonesia.
Abstract: This study investigated the pattern and seasonal index of influenza cases in Thailand. Our results showed that southern Thailand had the highest influenza incidence among the four regions of Thailand (i.e. north, northeast, central and southern Thailand). The influenza pattern in southern Thailand was similar to that of northeastern Thailand. Seasonal index values of influenza cases in Thailand were higher in the hot season than in the wet season. Influenza cases started to increase at the beginning of the hot season (April), reached a maximum in August, rapidly declined in the middle of the wet season and reached the lowest value in December. Seasonal index values for northern Thailand differed from other regions of Thailand.
Abstract: Apart from geometry, functionality is one of the most
significant hallmarks of a product. The functionality of a product can
be considered as the fundamental justification for a product
existence. Therefore a functional analysis including a complete and
reliable descriptor has a high potential to improve product
development process in various fields especially in knowledge-based
design. One of the important applications of the functional analysis
and indexing is in retrieval and design reuse concept. More than 75%
of design activity for a new product development contains reusing
earlier and existing design know-how. Thus, analysis and
categorization of product functions concluded by functional
indexing, influences directly in design optimization. This paper
elucidates and evaluates major classes for functional analysis by
discussing their major methods. Moreover it is finalized by
presenting a noble hybrid approach for functional analysis.
Abstract: Among other factors that characterize satellite communication
channels is their high bit error rate. We present a system for
still image transmission over noisy satellite channels. The system
couples image compression together with error control codes to
improve the received image quality while maintaining its bandwidth
requirements. The proposed system is tested using a high resolution
satellite imagery simulated over the Rician fading channel. Evaluation
results show improvement in overall system including image quality
and bandwidth requirements compared to similar systems with different
coding schemes.
Abstract: The evolution of technology and construction techniques has enabled the upgrading of transport networks. In particular, the high-speed rail networks allow convoys to peak at above 300 km/h. These structures, however, often significantly impact the surrounding environment. Among the effects of greater importance are the ones provoked by the soundwave connected to train transit. The wave propagation affects the quality of life in areas surrounding the tracks, often for several hundred metres. There are substantial damages to properties (buildings and land), in terms of market depreciation. The present study, integrating expertise in acoustics, computering and evaluation fields, outlines a useful model to select project paths so as to minimize the noise impact and reduce the causes of possible litigation. It also facilitates the rational selection of initiatives to contain the environmental damage to the already existing railway tracks. The research is developed with reference to the Italian regulatory framework (usually more stringent than European and international standards) and refers to a case study concerning the high speed network in Italy.
Abstract: A Watson-Crick automaton is recently introduced as a
computational model of DNA computing framework. It works on
tapes consisting of double stranded sequences of symbols. Symbols
placed on the corresponding cells of the double-stranded sequences are
related by a complimentary relation. In this paper, we investigate a
variation of Watson-Crick automata in which both heads read the tape
in reverse directions. They are called reverse Watson-Crick finite
automata (RWKFA). We show that all of following four classes, i.e.,
simple, 1-limited, all-final, all-final and simple, are equal to
non-restricted version of RWKFA.
Abstract: In this paper, we use nonlinear system identification method to predict and detect process fault of a cement rotary kiln. After selecting proper inputs and output, an input-output model is identified for the plant. To identify the various operation points in the
kiln, Locally Linear Neuro-Fuzzy (LLNF) model is used. This model is trained by LOLIMOT algorithm which is an incremental treestructure
algorithm. Then, by using this method, we obtained 3
distinct models for the normal and faulty situations in the kiln. One of the models is for normal condition of the kiln with 15 minutes
prediction horizon. The other two models are for the two faulty situations in the kiln with 7 minutes prediction horizon are presented.
At the end, we detect these faults in validation data. The data collected from White Saveh Cement Company is used for in this study.
Abstract: Hydrogen that used as fuel in fuel cell vehicles can be
produced from renewable sources such as wind, solar, and hydro
technologies. PV-electrolyzer is one of the promising methods to
produce hydrogen with zero pollution emission. Hydrogen
production from a PV-electrolyzer system depends on the efficiency
of the electrolyzer and photovoltaic array, and sun irradiance at that
site. In this study, the amount of hydrogen is obtained using
mathematical equations for difference driving distance and sun peak
hours. The results show that the minimum of 99 PV modules are used
to generate 1.75 kgH2 per day for two vehicles.
Abstract: Today-s manufacturing companies are facing multiple and dynamic customer-supplier-relationships embedded in nonhierarchical production networks. This complex environment leads to problems with delivery reliability and wasteful turbulences throughout the entire network. This paper describes an operational model based on a theoretical framework which improves delivery reliability of each individual customer-supplier-relationship within non-hierarchical production networks of the European machinery and equipment industry. By developing a non-centralized coordination mechanism based on determining the value of delivery reliability and derivation of an incentive system for suppliers the number of in time deliveries can be increased and thus the turbulences in the production network smoothened. Comparable to an electronic stock exchange the coordination mechanism will transform the manual and nontransparent process of determining penalties for delivery delays into an automated and transparent market mechanism creating delivery reliability.
Abstract: During more than a decade, many proposals and standards have been designed to deal with the mobility issues; however, there are still some serious limitations in basing solutions on them. In this paper we discuss the possibility of handling mobility at the application layer. We do this while revisiting the conventional implementation of the Two Phase Commit (2PC) protocol which is a fundamental asset of transactional technology for ensuring the consistent commitment of distributed transactions. The solution is based on an execution framework providing an efficient extension that is aware of the mobility and preserves the 2PC principle.
Abstract: In an interval graph G = (V,E) the distance between two vertices u, v is de£ned as the smallest number of edges in a path joining u and v. The eccentricity of a vertex v is the maximum among distances from all other vertices of V . The diameter (δ) and radius (ρ) of the graph G is respectively the maximum and minimum among all the eccentricities of G. The center of the graph G is the set C(G) of vertices with eccentricity ρ. In this context our aim is to establish the relation ρ = δ 2 for an interval graph and to determine the center of it.
Abstract: In this paper spatial variability of some chemical and
physical soil properties were investigated in mountain rangelands of
Nesho, Mazandaran province, Iran. 110 soil samples from 0-30 cm
depth were taken with systematic method on grid 30×30 m2 in
regions with different vegetation cover and transported to laboratory.
Then soil chemical and physical parameters including Acidity (pH),
Electrical conductivity, Caco3, Bulk density, Particle density, total
phosphorus, total Nitrogen, available potassium, Organic matter,
Saturation moisture, Soil texture (percentage of sand, silt and clay),
Sodium, Calcium, magnesium were measured in laboratory. Data
normalization was performed then was done statistical analysis for
description of soil properties and geostatistical analysis for indication
spatial correlation between these properties and were perpetrated
maps of spatial distribution of soil properties using Kriging method.
Results indicated that in the study area Saturation moisture and
percentage of Sand had highest and lowest spatial correlation
respectively.
Abstract: Knowledge Discovery in Databases (KDD) is the process of extracting previously unknown, hidden and interesting patterns from a huge amount of data stored in databases. Data mining is a stage of the KDD process that aims at selecting and applying a particular data mining algorithm to extract an interesting and useful knowledge. It is highly expected that data mining methods will find interesting patterns according to some measures, from databases. It is of vital importance to define good measures of interestingness that would allow the system to discover only the useful patterns. Measures of interestingness are divided into objective and subjective measures. Objective measures are those that depend only on the structure of a pattern and which can be quantified by using statistical methods. While, subjective measures depend only on the subjectivity and understandability of the user who examine the patterns. These subjective measures are further divided into actionable, unexpected and novel. The key issues that faces data mining community is how to make actions on the basis of discovered knowledge. For a pattern to be actionable, the user subjectivity is captured by providing his/her background knowledge about domain. Here, we consider the actionability of the discovered knowledge as a measure of interestingness and raise important issues which need to be addressed to discover actionable knowledge.
Abstract: Natural frequencies and dynamic response of a spur
gear sector are investigated using a two dimensional finite element
model that offers significant advantages for dynamic gear analyses.
The gear teeth are analyzed for different operating speeds. A primary
feature of this modeling is determination of mesh forces using a
detailed contact analysis for each time step as the gears roll through
the mesh. Transient mode super position method has been used to
find horizontal and vertical components of displacement and
dynamic stress. The finite element analysis software ANSYS has
been used on the proposed model to find the natural frequencies by
Block Lanczos technique and displacements and dynamic stresses by
transient mode super position method. A comparison of theoretical
(natural frequency and static stress) results with the finite element
analysis results has also been done. The effect of rotational speed of
the gears on the dynamic response of gear tooth has been studied and
design limits have been discussed.
Abstract: The transient hydrodynamics and thermal behaviors of
fluid flow in open-ended vertical parallel-plate porous microchannel are investigated semi-analytically under the effect of the hyperbolic
heat conduction model. The model that combines both the continuum approach and the possibility of slip at the boundary is adopted in the
study. The Effects of Knudsen number , Darcy number , and thermal relaxation time on the microchannel hydrodynamics and thermal behaviors are investigated using the hyperbolic heat
conduction models. It is found that as increases the slip in the hydrodynamic and thermal boundary condition increases. This slip in
the hydrodynamic boundary condition increases as increases. Also, the slip in the thermal boundary condition increases as
decreases especially the early stage of time.