Abstract: Sedimentation formation is a complex hydraulic phenomenon that has emerged as a major operational and maintenance consideration in modern hydraulic engineering in general and river engineering in particular. Sediments accumulation along the river course and their eventual storage in a form of islands affect water intake in the canal systems that are fed by the storage reservoirs. Without proper management, sediment transport can lead to major operational challenges in water distribution system of arid regions like the Dez and Hamidieh command areas. The paper aims to investigate sedimentation in the Western Canal of Dez Diversion Weir using the SHARC model and compare the results with the two intake structures of the Hamidieh dam in Iran using SSIIM model. The objective was to identify the factors which influence the process, check reliability of outcome and provide ways in which to mitigate the implications on operation and maintenance of the structures. Results estimated sand and silt bed loads concentrations to be 193 ppm and 827ppm respectively. This followed ,ore or less similar pattern in Hamidieh where the sediment formation impeded water intake in the canal system. Given the available data on average annual bed loads and average suspended sediment loads of 165ppm and 837ppm in the Dez, there was a significant statistical difference (16%) between the sand grains, whereas no significant difference (1.2%) was find in the silt grain sizes. One explanation for such finding being that along the 6 Km river course there was considerable meandering effects which explains recent shift in the hydraulic behavior along the stream course under investigation. The sand concentration in downstream relative to present state of the canal showed a steep descending curve. Sediment trapping on the other hand indicated a steep ascending curve. These occurred because the diversion weir was not considered in the simulation model. The comparative study showed very close similarities in the results which explains the fact that both software can be used as accurate and reliable analytical tools for simulation of the sedimentation in hydraulic engineering.
Abstract: Female breast cancer is the second in frequency after cervical cancer. Surgery is the most common treatment for breast cancer, followed by chemotherapy as a treatment of choice. Although effective, it causes serious side effects. Controlled-release drug delivery is an alternative method to improve the efficacy and safety of the treatment. It can release the dosage of drug between the minimum effect concentration (MEC) and minimum toxic concentration (MTC) within tumor tissue and reduce the damage of normal tissue and the side effect. Because an in vivo experiment of this system can be time-consuming and labor-intensive, a mathematical model is desired to study the effects of important parameters before the experiments are performed. Here, we describe a 3D mathematical model to predict the release of doxorubicin from pluronic gel to treat human breast cancer. This model can, ultimately, be used to effectively design the in vivo experiments.
Abstract: A generalized unified power quality conditioner
(GUPQC) by using three single-phase three-level voltage source
converters (VSCs) connected back-to-back through a common dc
link is proposed in this paper as a new custom power device for a
three-feeder distribution system. One of the converters is connected
in shunt with one feeder for mitigation of current harmonics and
reactive power compensation, while the other two VSCs are
connected in series with the other two feeders to maintain the load
voltage sinusoidal and at constant level. A new control scheme based
on synchronous reference frame is proposed for series converters.
The simulation analysis on compensation performance of GUPQC
based on PSCAD/EMTDC is reported.
Abstract: The techniques for estimating the adhesive and cohesive strength in high velocity oxy fuel (HVOF) thermal spray coatings have been discussed and compared. The development trend and the last investigation have been studied. We will focus on benefits and limitations of these methods in different process and materials.
Abstract: We derive simple sets of equations to describe the microwave response of a thin film of magnetized hydrogen plasma in the presence of carbon nanotubes, which were grown by ironcatalyzed high-pressure disproportionation (HiPco). By considering the interference effects due to multiple reflections between thin plasma film interfaces, we present the effects of the continuously changing external magnetic field and plasma parameters on the reflected power, absorbed power, and transmitted power in the system. The simulation results show that the interference effects play an important role in the reflectance, transmittance and absorptance of microwave radiation at the magnetized plasma slab. As a consequence, the interference effects lead to a sinusoidal variation of the reflected intensity and can greatly reduce the amount of reflection power, but the absorption power increases.
Abstract: Uncertainties of a serial production line affect on the
production throughput. The uncertainties cannot be prevented in a
real production line. However the uncertain conditions can be
controlled by a robust prediction model. Thus, a hybrid model
including autoregressive integrated moving average (ARIMA) and
multiple polynomial regression, is proposed to model the nonlinear
relationship of production uncertainties with throughput. The
uncertainties under consideration of this study are demand, breaktime,
scrap, and lead-time. The nonlinear relationship of production
uncertainties with throughput are examined in the form of quadratic
and cubic regression models, where the adjusted R-squared for
quadratic and cubic regressions was 98.3% and 98.2%. We optimized
the multiple quadratic regression (MQR) by considering the time
series trend of the uncertainties using ARIMA model. Finally the
hybrid model of ARIMA and MQR is formulated by better adjusted
R-squared, which is 98.9%.
Abstract: As more people from non-technical backgrounds
are becoming directly involved with large-scale ontology
development, the focal point of ontology research has shifted
from the more theoretical ontology issues to problems
associated with the actual use of ontologies in real-world,
large-scale collaborative applications. Recently the National
Science Foundation funded a large collaborative ontology
development project for which a new formal ontology model,
the Ontology Abstract Machine (OAM), was developed to
satisfy some unique functional and data representation
requirements. This paper introduces the OAM model and the
related algorithms that enable maintenance of an ontology that
supports node-based user access. The successful software
implementation of the OAM model and its subsequent
acceptance by a large research community proves its validity
and its real-world application value.
Abstract: This research project is developed in order to study
managerial styles of modern Thai executives. The thorough
understanding will lead to continuous improvement and efficient
performance of Thai business organizations. Regarding managerial
skills, Thai executives focus heavily upon human skills. Also, the
negotiator roles are most emphasis in their management. In addition,
Thai executives pay most attention to the fundamental management
principles including Harmony and Unity of Direction of the
organizations. Moreover, the management techniques, consisting of
Team work and Career Planning are of their main concern. Finally,
Thai executives wish to enhance their firms- image and employees-
morale through conducting the ethical and socially responsible
activities. The major tactic deployed to stimulate employees- ethical
behaviors and mindset is Code of Ethics development.
Abstract: Maize and Indian mustard are significant crops in
semi-arid climate zones of India. Improved water management
requires precise scheduling of irrigation, which in turn requires an
accurate computation of daily crop evapotranspiration (ETc). Daily
crop evapotranspiration comes as a product of reference
evapotranspiration (ET0) and the growth stage specific crop
coefficients modified for daily variation. The first objective of
present study is to develop crop coefficients Kc for Maize and Indian
mustard. The estimated values of Kc for maize at the four crop
growth stages (initial, development, mid-season, and late season) are
0.55, 1.08, 1.25, and 0.75, respectively, and for Indian mustard the Kc
values at the four growth stages are 0.3, 0.6, 1.12, and 0.35,
respectively. The second objective of the study is to compute daily
crop evapotranspiration from ET0 and crop coefficients. Average
daily ETc of maize varied from about 2.5 mm/d in the early growing
period to > 6.5 mm/d at mid season. The peak ETc of maize is 8.3
mm/d and it occurred 64 days after sowing at the reproductive growth
stage when leaf area index was 4.54. In the case of Indian mustard,
average ETc is 1 mm/d at the initial stage, >1.8 mm/d at mid season
and achieves a peak value of 2.12 mm/d on 56 days after sowing.
Improved schedules of irrigation have been simulated based on daily
crop evapo-transpiration and field measured data. Simulation shows a
close match between modeled and field moisture status prevalent
during crop season.
Abstract: This paper presents a multi-objective order allocation
planning problem with the consideration of various real-world
production features. A novel hybrid intelligent optimization model,
integrating a multi-objective memetic optimization process, a Monte
Carlo simulation technique and a heuristic pruning technique, is
proposed to handle this problem. Experiments based on industrial data
are conducted to validate the proposed model. Results show that (1)
the proposed model can effectively solve the investigated problem by
providing effective production decision-making solutions, which
outperformsan NSGA-II-based optimization process and an industrial
method.
Abstract: The experiment was then conducted to investigate the
effect of cassava peel addition in the concentrate on the performance
of lactating dairy cows. Twenty four Holstein Friesian crossbred
(>87.5% Holstein Friesian) lactating dairy cows in mid lactation;
averaging 12.2+2.1 kg of milk, 119+45 days in milk, 44.1+6.2
months old and 449+33 kg live weight, were stratified for milk yield,
days in milk, age, stage of lactation and body weight, and then
randomly allocated to three treatment groups. The first, second and
third groups were fed concentrates containing the respective cassava
peel, 0, 20 and 40%. All cows were fed ad libitum corn silage and
freely access to clean water. Dry matter intake, 4%FCM, milk
composition and body weight change were affected (P
Abstract: This paper focuses on robust design and optimization
of industrial production wastes. Past literatures were reviewed to case
study Clamason Industries Limited (CIL) - a leading ladder-tops
manufacturer. A painstaking study of the firm-s practices at the shop
floor revealed that Over-production, Waiting time, Excess inventory,
and Defects are the major wastes that are impeding their progress and
profitability. Design expert8 software was used to apply Taguchi
robust design and response surface methodology in order to model,
analyse and optimise the wastes cost in CIL. Waiting time and overproduction
rank first and second in contributing to the costs of wastes
in CIL. For minimal wastes cost the control factors of overproduction,
waiting-time, defects and excess-inventory must be set at
0.30, 390.70, 4 and 55.70 respectively for CIL. The optimal value of
cost of wastes for the months studied was 22.3679. Finally, a
recommendation was made that for the company to enhance their
profitability and customer satisfaction, they must adopt the Shingeo
Shingo-s Single Minute Exchange of Dies (SMED), which will
immediately tackle the waste of waiting by drastically reducing their
setup time.
Abstract: This paper proposes a set of quasi-static mathematical
model of magnetic fields caused by high voltage conductors of
distribution transformer by using a set of second-order partial
differential equation. The modification for complex magnetic field
analysis and time-harmonic simulation are also utilized. In this
research, transformers were study in both balanced and unbalanced
loading conditions. Computer-based simulation utilizing the threedimensional
finite element method (3-D FEM) is exploited as a tool
for visualizing magnetic fields distribution volume a distribution
transformer. Finite Element Method (FEM) is one among popular
numerical methods that is able to handle problem complexity in
various forms. At present, the FEM has been widely applied in most
engineering fields. Even for problems of magnetic field distribution,
the FEM is able to estimate solutions of Maxwell-s equations
governing the power transmission systems. The computer simulation
based on the use of the FEM has been developed in MATLAB
programming environment.
Abstract: The submitted paper deals with the problems of
trapping and enriching the gases and aerosols of the substances to be
determined in the ambient atmosphere. Further, the paper is focused
on the working principle of the miniaturized portable continuous
concentrator we have designed and the possibilities of its
application in air sampling and accumulation of organic and
inorganic substances with which the air is contaminated. The stress is
laid on trapping vapours and aerosols of solid substances with the
comparatively low vapour tension such as explosive compounds.
Abstract: In this paper, vapour-liquid critical locus for the
binary system acetone + chloroform was determined experimentally
over the whole range of composition. The critical property
measurements were carried out using a dynamic-synthetic apparatus,
employed in the dynamic mode. The critical points are visually
determined by observing the critical opalescence and the
simultaneous disappearance and reappearance of the meniscus in the
middle of a high-pressure view cell which withstands operations up
to 673K and 20MPa. The experimental critical points measured in
this work were compared to those available in literature.
Abstract: This paper proposes an innovative methodology for
Acceptance Sampling by Variables, which is a particular category of
Statistical Quality Control dealing with the assurance of products
quality. Our contribution lies in the exploitation of machine learning
techniques to address the complexity and remedy the drawbacks of
existing approaches. More specifically, the proposed methodology
exploits Artificial Neural Networks (ANNs) to aid decision making
about the acceptance or rejection of an inspected sample. For any
type of inspection, ANNs are trained by data from corresponding
tables of a standard-s sampling plan schemes. Once trained, ANNs
can give closed-form solutions for any acceptance quality level and
sample size, thus leading to an automation of the reading of the
sampling plan tables, without any need of compromise with the
values of the specific standard chosen each time. The proposed
methodology provides enough flexibility to quality control engineers
during the inspection of their samples, allowing the consideration of
specific needs, while it also reduces the time and the cost required for
these inspections. Its applicability and advantages are demonstrated
through two numerical examples.
Abstract: The ferroelectric behavior of barium strontium
titanate (BST) in thin film form has been investigated in order to
study the possibility of using BST for ferroelectric gate-field effect
transistor (FeFET) for memory devices application. BST thin films
have been fabricated as Al/BST/Pt/SiO2/Si-gate configuration. The
variation of the dielectric constant (ε) and tan δ with frequency have
been studied to ensure the dielectric quality of the material. The
results show that at low frequencies, ε increases as the Ba content
increases, whereas at high frequencies, it shows the opposite
variation, which is attributed to the dipole dynamics. tan δ shows low
values with a peak at the mid-frequency range. The ferroelectric
behavior of the Al/BST/Pt/SiO2/Si has been investigated using C-V
characteristics. The results show that the strength of the ferroelectric
hysteresis loop increases as the Ba content increases; this is attributed
to the grain size and dipole dynamics effect.
Abstract: We study the performance of compressed beamforming
weights feedback technique in generalized triangular decomposition
(GTD) based MIMO system. GTD is a beamforming technique that
enjoys QoS flexibility. The technique, however, will perform at its
optimum only when the full knowledge of channel state information
(CSI) is available at the transmitter. This would be impossible in
the real system, where there are channel estimation error and limited
feedback. We suggest a way to implement the quantized beamforming
weights feedback, which can significantly reduce the feedback data,
on GTD-based MIMO system and investigate the performance of
the system. Interestingly, we found that compressed beamforming
weights feedback does not degrade the BER performance of the
system at low input power, while the channel estimation error
and quantization do. For comparison, GTD is more sensitive to
compression and quantization, while SVD is more sensitive to the
channel estimation error. We also explore the performance of GTDbased
MU-MIMO system, and find that the BER performance starts
to degrade largely at around -20 dB channel estimation error.
Abstract: The article deals with pneumatic and hot wire
anemometry measurement on subsonic axi-symmetric air ejector.
Performances of the ejector with and without pulsations of primary
flow are compared, measuring of characteristic pressures and mass
flow rates are performed and ejector efficiency is evaluated. The
pulsations of primary flow are produced by a synthetic jet generator,
which is placed in the supply line of the primary flow just in front of
the primary nozzle. The aim of the pulsation is to intensify the
mixing process. In the article we present: Pressure measuring of
pulsation on the mixing chamber wall, behind the mixing chamber
and behind the diffuser measured by fast pressure transducers and
results of hot wire anemometry measurement. It was found out that
using of primary flow pulsations yields higher back pressure behind
the ejector and higher efficiency. The processes in this ejector and
influences of primary flow pulsations on the mixing processes are
described.
Abstract: The interline power flow controller (IPFC) is one of
the latest generation flexible AC transmission systems (FACTS)
controller used to control power flows of multiple transmission lines.
This paper presents a mathematical model of IPFC, termed as power
injection model (PIM). This model is incorporated in Newton-
Raphson (NR) power flow algorithm to study the power flow control
in transmission lines in which IPFC is placed. A program in
MATLAB has been written in order to extend conventional NR
algorithm based on this model. Numerical results are carried out on a
standard 2 machine 5 bus system. The results without and with IPFC
are compared in terms of voltages, active and reactive power flows to
demonstrate the performance of the IPFC model.