Abstract: In this paper, we investigate the effect of friendly
jamming power allocation strategies on the achievable average
secrecy rate over a bank of parallel fading wiretap channels.
We investigate the achievable average secrecy rate in parallel
fading wiretap channels subject to Rayleigh and Rician fading.
The achievable average secrecy rate, due to the presence of a
line-of-sight component in the jammer channel is also evaluated.
Moreover, we study the detrimental effect of correlation across the
parallel sub-channels, and evaluate the corresponding decrease in the
achievable average secrecy rate for the various fading configurations.
We also investigate the tradeoff between the transmission power
and the jamming power for a fixed total power budget. Our
results, which are applicable to current orthogonal frequency division
multiplexing (OFDM) communications systems, shed further light on
the achievable average secrecy rates over a bank of parallel fading
channels in the presence of friendly jammers.
Abstract: The paper presents a thermodynamic cycle analysis
for three turboshaft engines. The first cycle is a Brayton cycle,
describing the evolution of a classical turboshaft, based on the
Klimov TV2 engine. The other four cycles aim at approaching an
Ericsson cycle, by replacing the Brayton cycle adiabatic expansion in
the turbine by quasi-isothermal expansion. The maximum quasi-
Ericsson cycles temperature is set to a lower value than the maximum
Brayton cycle temperature, equal to the Brayton cycle power turbine
inlet temperature, in order to decrease the engine NOx emissions.
Also, the power/expansion ratio distribution over the stages of the gas
generator turbine is maintained the same. In two of the considered
quasi-Ericsson cycles, the efficiencies of the gas generator turbine, as
well as the power/expansion ratio distribution over the stages of the
gas generator turbine are maintained the same as for the reference
case, while for the other two cases, the efficiencies are increased in
order to obtain the same shaft power as in the reference case. For the
two cases respecting the first condition, both the shaft power and the
thermodynamic efficiency of the engine decrease, while for the other
two, the power and efficiency are maintained, as a result of assuming
new, more efficient gas generator turbines.
Abstract: In this paper, a new design of spherical robotic system
based on the concepts of gimbal structure and gyro dynamics is
presented. Robots equipped with multiple wheels and complex
steering mechanics may increase the weight and degrade the energy
transmission efficiency. In addition, the wheeled and legged robots are
relatively vulnerable to lateral impact and lack of lateral mobility.
Therefore, the proposed robotic design uses a spherical shell as the
main body for ground locomotion, instead of using wheel devices.
Three spherical shells are structured in a similar way to a gimbal
device and rotate like a gyro system. The design and mechanism of the
proposed robotic system is introduced. In addition, preliminary results
of the dynamic model based on the principles of planar rigid body
kinematics and Lagrangian equation are included. Simulation results
and rig construction are presented to verify the concepts.
Abstract: Interaction of Schiff base complexes of Iron and
Manganese: Iron [N, N’ Bis (5- (triphenyl phosphonium methyl)
salicylidene) -1, 2 ethanediamine) chloride, [Fe Salen]Cl; Manganese
[N, N’ Bis (5- (triphenyl phosphonium methyl) salicylidene) -1, 2
ethanediamine) acetate, were investigated by spectroscopic and
isothermal titration calorimetry techniques (ITC).
The absorbance spectra of complexes have shown hyper and
hypochromism in the presence of DNA that is indication of
interaction of complexes with DNA. The linear dichroism (LD)
measurements confirmed the bending of DNA in the presence of
complexes.
Furthermore, Isothermal titration calorimetry experiments
approved that complexes bound to DNA on the base of both
electrostatic and hydrophobic interactions. More, ITC profile exhibits
the existence of two binding phases for the complexes. Antibacterial
activity of ligand and complexes were tested in vitro to evaluate their
activity against the gram positive and negative bacteria.
Abstract: The objectives of the study were to determine the
marketing mix factors that influencing tourist’s destination decision
making for cultural tourism in the Chonburi province. Both
quantitative and qualitative data were applied in this study. The
samples of 400 cases for quantitative analysis were tourists (both
Thai and foreign) who were interested in cultural tourism in the
Chonburi province, and traveled to cultural sites in Chonburi and 14
representatives from provincial tourism committee of Chonburi and
local tourism experts. Statistics utilized in this research included
frequency, percentage, mean, standard deviation, and multiple
regression analysis. The study found that Thai and foreign tourists
are influenced by different important marketing mix factors. The
important factors for Thai respondents were physical evidence, price,
people, and place at high importance level. For foreign respondents,
physical evidence, price, people, and process were high importance
level, whereas, product, place and promotion were moderate
importance level.
Abstract: The Algeria by its location offers a rich and diverse
vegetation. A large number of aromatic and medicinal plants grow
spontaneously. The interest in these plants has continued to grow in
recent years. Their particular properties due to the essential oil
fraction can be utilized to treat microbial infections. To this end, and
in the context of the valuation of the Algerian flora, we became
interested in the species of the family Lamiaceae which is one of the
most used as a global source of spices. The plant on which we have
based our choice is a species of sage "Salvia officinalis" from the
Isser localized region within the province of Boumerdes. This work
focuses on the study of the antimicrobial activity of essential oil
extracted from the leaves of Salvia officinalis. The extraction is
carried out by essential oil hydrodistillation and reveals a yield of
1.06℅. The study of the antimicrobial activity of the essential oil by
the method of at aromatogramme shown that Gram positive bacteria
are most susceptible (Staphylococcus aureus and Bacillus subtilis)
with a strong inhibition of growth. The yeast Candida albicans
fungus Aspergillus niger and have shown moderately sensitive.
Abstract: Two finite element (FEM) models are presented in
this paper to address the random nature of the response of glued
timber structures made of wood segments with variable elastic
moduli evaluated from 3600 indentation measurements. This total
database served to create the same number of ensembles as was the
number of segments in the tested beam. Statistics of these ensembles
were then assigned to given segments of beams and the Latin
Hypercube Sampling (LHS) method was called to perform 100
simulations resulting into the ensemble of 100 deflections subjected
to statistical evaluation. Here, a detailed geometrical arrangement of
individual segments in the laminated beam was considered in the
construction of two-dimensional FEM model subjected to in fourpoint
bending to comply with the laboratory tests. Since laboratory
measurements of local elastic moduli may in general suffer from a
significant experimental error, it appears advantageous to exploit the
full scale measurements of timber beams, i.e. deflections, to improve
their prior distributions with the help of the Bayesian statistical
method. This, however, requires an efficient computational model
when simulating the laboratory tests numerically. To this end, a
simplified model based on Mindlin’s beam theory was established.
The improved posterior distributions show that the most significant
change of the Young’s modulus distribution takes place in laminae in
the most strained zones, i.e. in the top and bottom layers within the
beam center region. Posterior distributions of moduli of elasticity
were subsequently utilized in the 2D FEM model and compared with
the original simulations.
Abstract: This paper introduces a proposal scheme for an
Intelligent System applied to Pedagogical Advising using Case-Based
Reasoning, to find consolidated solutions before used for the new
problems, making easier the task of advising students to the
pedagogical staff. We do intend, through this work, introduce the
motivation behind the choices for this system structure, justifying the
development of an incremental and smart web system who learns
bests solutions for new cases when it’s used, showing technics and
technology.
Abstract: In this study, the Compressive strength of concretes
made with Ground Granulated Blast furnace Slag (GGBS),
Pulverised Fuel Ash (PFA), Rice Husk Ash (RHA) and Waste Glass
Powder (WGP) after they were exposed 7800C (exposure duration of
around 60 minutes) and then allowed to cool down gradually in the
furnace for about 280 minutes at water binder ratio of 0.50 was
investigated. GGBS, PFA, RHA and WGP were used to replace up to
20% Portland cement in the control concrete. Test for the
determination of workability, compressive strength and tensile
splitting strength of the concretes were carried out and the results
were compared with control concrete. The test results showed that the
compressive strength decreased by an average of around 30% after
the concretes were exposed to the heating and cooling scenario.
Abstract: Catalytic combustion of methane is imperative due to
stability of methane at low temperature. Methane (CH4), therefore,
remains unconverted in vehicle exhausts thereby causing greenhouse
gas GHG emission problem. In this study, heterogeneous catalysts of
palladium with bio-char (2 wt% Pd/Bc) and Al2O3 (2wt% Pd/ Al2O3)
supports were prepared by incipient wetness impregnation and then
subsequently tested for catalytic combustion of CH4. Support-porous
heterogeneous catalytic combustion (HCC) material were selected
based on factors such as surface area, porosity, thermal stability,
thermal conductivity, reactivity with reactants or products, chemical
stability, catalytic activity, and catalyst life. Sustainable and
renewable support-material of bio-mass char derived from palm shell
waste material was compared with those from the conventional
support-porous materials. Kinetic rate of reaction was determined for
combustion of methane on Palladium (Pd) based catalyst with Al2O3
support and bio-char (Bc). Material characterization was done using
TGA, SEM, and BET surface area. The performance test was
accomplished using tubular quartz reactor with gas mixture ratio of
3% methane and 97% air. The methane porous-HCC conversion was
carried out using online gas analyzer connected to the reactor that
performed porous-HCC. BET surface area for prepared 2 wt% Pd/Bc
is smaller than prepared 2wt% Pd/ Al2O3 due to its low porosity
between particles. The order of catalyst activity based on kinetic rate
on reaction of catalysts in low temperature was 2wt%
Pd/Bc>calcined 2wt% Pd/ Al2O3> 2wt% Pd/ Al2O3>calcined 2wt%
Pd/Bc. Hence agro waste material can successfully be utilized as an
inexpensive catalyst support material for enhanced CH4 catalytic
combustion.
Abstract: Modern Portfolio Theory (MPT) according to
Markowitz states that investors form mean-variance efficient
portfolios which maximizes their utility. Markowitz proposed the
standard deviation as a simple measure for portfolio risk and the
lower semi-variance as the only risk measure of interest to rational
investors. This paper uses a third volatility estimator based on
intraday data and compares three efficient frontiers on the Croatian
Stock Market. The results show that range-based volatility estimator
outperforms both mean-variance and lower semi-variance model.
Abstract: This paper proposes five level diode clamped Z source
Inverter. The existing PWM techniques used for ZSI are restricted for
two level. The two level Z Source Inverter have high harmonic
distortions which effects the performance of the grid connected PV
system. To improve the performance of the system the number of
voltage levels in the output waveform need to be increased. This
paper presents comparative analysis of a five level diode clamped Z
source Inverter with different carrier based Modified Pulse Width
Modulation techniques. The parameters considered for comparison
are output voltage, voltage gain, voltage stress across switch and total
harmonic distortion when powered by same DC supply. Analytical
results are verified using MATLAB.
Abstract: Array-based gene expression analysis is a powerful
tool to profile expression of genes and to generate information on
therapeutic effects of new anti-cancer compounds. Anti-apoptotic
effect of thymoquinone was studied in MCF7 breast cancer cell line
using gene expression profiling with cDNA microarray. The purity
and yield of RNA samples were determined using RNeasyPlus Mini
kit. The Agilent RNA 6000 NanoLabChip kit evaluated the quantity
of the RNA samples. AffinityScript RT oligo-dT promoter primer
was used to generate cDNA strands. T7 RNA polymerase was used to
convert cDNA to cRNA. The cRNA samples and human universal
reference RNA were labelled with Cy-3-CTP and Cy-5-CTP,
respectively. Feature Extraction and GeneSpring softwares analysed
the data. The single experiment analysis revealed involvement of 64
pathways with up-regulated genes and 78 pathways with downregulated
genes. The MAPK and p38-MAPK pathways were
inhibited due to the up-regulation of PTPRR gene. The inhibition of
p38-MAPK suggested up-regulation of TGF-ß pathway. Inhibition of
p38-MAPK caused up-regulation of TP53 and down-regulation of
Bcl2 genes indicating involvement of intrinsic apoptotic pathway.
Down-regulation of CARD16 gene as an adaptor molecule regulated
CASP1 and suggested necrosis-like programmed cell death and
involvement of caspase in apoptosis. Furthermore, down-regulation
of GPCR, EGF-EGFR signalling pathways suggested reduction of
ER. Involvement of AhR pathway which control cytochrome P450
and glucuronidation pathways showed metabolism of Thymoquinone.
The findings showed differential expression of several genes in
apoptosis pathways with thymoquinone treatment in estrogen
receptor-positive breast cancer cells.
Abstract: Object-oriented modeling is spreading in current
simulation of physiological systems through the use of the individual
components of the model and its interconnections to define the
underlying dynamic equations. In this paper we describe the use of
both the SIMSCAPE and MODELICA simulation environments in
the object-oriented modeling of the closed loop cardiovascular
system. The performance of the controlled system was analyzed by
simulation in light of the existing hypothesis and validation tests
previously performed with physiological data. The described
approach represents a valuable tool in the teaching of physiology for
graduate medical students.
Abstract: Chemical vapor deposition (CVD) diamond coated
cutting tool has excellent cutting performance, it is the most ideal tool
for the processing of nonferrous metals and alloys, composites,
nonmetallic materials and other difficult-to-machine materials
efficiently and accurately. Depositing CVD diamond coating on the
cemented carbide with high cobalt content can improve its toughness
and strength, therefore, it is very important to research on the
preparation technology and cutting properties of CVD diamond coated
cemented carbide cutting tool with high cobalt content. The
preparation technology of boron-doped diamond (BDD) coating has
been studied and the coated drills were prepared. BDD coating were
deposited on the drills by using the optimized parameters and the SEM
results show that there are no cracks or collapses in the coating.
Cutting tests with the prepared drills against the silumin and aluminum
base printed circuit board (PCB) have been studied. The results show
that the wear amount of the coated drill is small and the machined
surface has a better precision. The coating does not come off during
the test, which shows good adhesion and cutting performance of the
drill.
Abstract: The capability of CNC gantry milling machines in
manufacturing long components has caused the expanded use of such
machines. On the other hand, the machines’ gantry rigidity can
reduce under severe loads or vibration during operation. Indeed, the
quality of machining is dependent on the machine’s dynamic
behavior throughout the operating process. For this reason, these
types of machines have always been used widely and are not
efficient. Therefore, they can usually be employed for rough
machining and may not produce adequate surface finishing. In this
paper, a CNC gantry milling machine with the potential to produce
good surface finish has been designed and analyzed. The lowest
natural frequency of this machine is 202 Hz corresponding to 12000
rpm at all motion amplitudes with a full range of suitable frequency
responses. Meanwhile, the maximum deformation under dead loads
for the gantry machine is 0.565*m, indicating that this machine tool
is capable of producing higher product quality.
Abstract: The main aim of the presented experiments is to
improve behaviour of sandwich structures under dynamic loading,
such as crash or explosion. This paper describes experimental
investigation on the response of new advanced materials to low and
high velocity load. Blast wave energy absorbers were designed using
two types of porous lightweight raw particle materials based on
expanded glass and ceramics with dimensions of 0.5-1 mm,
combined with polymeric binder. The effect of binder amount on the
static and dynamic properties of designed materials was observed.
Prism shaped specimens were prepared and loaded to obtain physicomechanical
parameters – bulk density, compressive and flexural
strength under quasistatic load, the dynamic response was determined
using Split Hopkinson Pressure bar apparatus. Numerical
investigation of the material behaviour in sandwich structure was
performed using implicit/explicit solver LS-Dyna. As the last step,
the developed material was used as the interlayer of blast resistant
litter bin, and it´s functionality was verified by real field blast tests.
Abstract: The purpose of the present work was to develop an
innovative food product with nutritional properties as well as
appealing organoleptic qualities. The product, a jam, was prepared
with the beans’ cooking water combined with fresh apple or carrot,
without the addition of any conservatives. Three different jams were
produced: bean and carrot, bean and apple and bean, apple and
cinnamon. The developed products underwent a sensorial analysis
that revealed that the bean, apple and cinnamon jam was globally
better accepted. However, with this study, the consumers determined
that the bean and carrot jam had the most attractive color and the
bean and apple jam the better consistency. Additionally, it was
possible to analyze the jams for their chemical components, namely
fat, fiber, protein, sugars and antioxidant activity. The obtained
results showed that the bean and carrot jam had the highest lipid
content, while the bean, apple and cinnamon jam had the highest
fiber content, when compared to the other two jams. Regarding the
sugar content, both jams with apple revealed similar sugar values,
which were higher than the sugar content of the bean and carrot jam.
The antioxidant activity was on average 10 mg TE/g.
Abstract: The paper describes the OAS role in dispute
resolution. The authors make an attempt to identify a general pattern
of the OAS activities within the peaceful settlement of interstate
conflicts, in the beginning of 21st century, as well as to analyze some
features of Honduras–Belize, Nicaragua–Honduras, Honduras–El
Salvador, Costa-Rica–Nicaragua, Colombia–Ecuador cases.
Abstract: Using the pseudopotential technique the Sagdeev
potential equation has been derived in a plasma consisting of twotemperature
nonisothermal electrons, negatively charged dust grains
and warm positive ions. The study shows that the presence of
nonisothermal two-temperature electrons and charged dust grains
have significant effects on the excitation and structure of the ionacoustic
double layers in the model plasma under consideration. Only
compressive type double layer is obtained in the present plasma
model. The double layer solution has also been obtained by including
higher order nonlinearity and nonisothermality, which is shown to
modify the amplitude and deform the shape of the double layer.