Abstract: Exact solution of an unsteady flow of elastico-viscous
fluid through a porous media in a tube of ellipsoidal cross section
under the influence of constant pressure gradient has been obtained in
this paper. Initially, the flow is generated by a constant pressure
gradient. After attaining the steady state, the pressure gradient is
suddenly withdrawn and the resulting fluid motion in a tube of
ellipsoidal cross section by taking into account of the porosity factor
of the bounding surface is investigated. The problem is solved in twostages
the first stage is a steady motion in tube under the influence of
a constant pressure gradient, the second stage concern with an
unsteady motion. The problem is solved employing separation of
variables technique. The results are expressed in terms of a nondimensional
porosity parameter (K) and elastico-viscosity parameter
(β), which depends on the Non-Newtonian coefficient. The flow
parameters are found to be identical with that of Newtonian case as
elastic-viscosity parameter tends to zero and porosity tends to
infinity. It is seen that the effect of elastico-viscosity parameter and
the porosity parameter of the bounding surface has significant effect
on the velocity parameter.
Abstract: This paper presents circuit models to analyze the
conducted susceptibility of multiconductor shielded cables in
frequency domains using Branin’s method, which is referred to as the
method of characteristics. These models, which can be used directly
in the time and frequency domains, take into account the presence of
both the transfer impedance and admittance. The conducted
susceptibility is studied by using an injection current on the cable
shield as the source. Two examples are studied; a coaxial shielded
cable and shielded cables with two parallel wires (i.e., twinax cables).
This shield has an asymmetry (one slot on the side). Results obtained
by these models are in good agreement with those obtained by other
methods.
Abstract: The Markov decision process (MDP) based
methodology is implemented in order to establish the optimal
schedule which minimizes the cost. Formulation of MDP problem
is presented using the information about the current state of pipe,
improvement cost, failure cost and pipe deterioration model. The
objective function and detailed algorithm of dynamic programming
(DP) are modified due to the difficulty of implementing the
conventional DP approaches. The optimal schedule derived from
suggested model is compared to several policies via Monte
Carlo simulation. Validity of the solution and improvement in
computational time are proved.
Abstract: This study aimed to identify the alignment of
understanding and assessment practices among secondary school
teachers. The study was carried out using quantitative descriptive
study. The sample consisted of 164 teachers who taught Form 1 and 2
from 11 secondary schools in the district of North Kinta, Perak,
Malaysia. Data were obtained from 164 respondents who answered
Expectation Alignment Understanding and Practices of School
Assessment (PEKDAPS) questionnaire. The data were analysed
using SPSS 17.0+. The Cronbach’s alpha value obtained through
PEKDAPS questionnaire pilot study was 0.86. The results showed
that teachers' performance in PEKDAPS based on the mean value
was less than 3, which means that perfect alignment does not occur
between the understanding and practices of school assessment. Two
major PEKDAPS sub-constructs of articulation across grade and age
and usability of the system were higher than the moderate alignment
of the understanding and practices of school assessment (Min=2.0).
The content focused of PEKDAPs sub-constructs which showed
lower than the moderate alignment of the understanding and practices
of school assessment (Min=2.0). Another two PEKDAPS subconstructs
of transparency and fairness and the pedagogical
implications showed moderate alignment (2.0). The implications of
the study is that teachers need to fully understand the importance of
alignment among components of assessment, learning and teaching
and learning objectives as strategies to achieve quality assessment
process.
Abstract: Urban Search and Rescue (USAR) is a functional
capability that has been developed to allow the United Kingdom Fire
and Rescue Service to deal with ‘major incidents’ primarily involving
structural collapse. The nature of the work undertaken by USAR
means that staying out of a damaged or collapsed building structure is
not usually an option for search and rescue personnel. As a result
there is always a risk that they themselves could become victims. For
this paper, a systematic and investigative review using desk research
was undertaken to explore the role which structural engineering can
play in assisting search and rescue personnel to conduct structural
assessments when in the field. The focus is on how search and rescue
personnel can assess damaged and collapsed building structures, not
just in terms of structural damage that may been countered, but also
in relation to structural stability. Natural disasters, accidental
emergencies, acts of terrorism and other extreme events can vary
significantly in nature and ferocity, and can cause a wide variety of
damage to building structures. It is not possible or, even realistic, to
provide search and rescue personnel with definitive guidelines and
procedures to assess damaged and collapsed building structures as
there are too many variables to consider. However, understanding
what implications damage may have upon the structural stability of a
building structure will enable search and rescue personnel to better judge
and quantify risk from a life-safety standpoint. It is intended that this
will allow search and rescue personnel to make informed decisions
and ensure every effort is made to mitigate risk, so that they
themselves do not become victims.
Abstract: Over the years, it has been extensively established that
the practice of assuming a structure being fixed at base, leads to gross
errors in evaluation of its overall response due to dynamic loadings
and overestimations in design. The extent of these errors depends on
a number of variables; soil type being one of the major factor. This
paper studies the effect of Soil Structure Interaction (SSI) on multistorey
buildings with varying under-laying soil types after proper
validation of the effect of SSI. Analysis for soft, stiff and very stiff
base soils has been carried out, using a powerful Finite Element
Method (FEM) software package ANSYS v14.5. Results lead to
some very important conclusions regarding time period, deflection
and acceleration responses.
Abstract: Background: The objectives of this study were to
assess patient’s knowledge of appropriate sublingual glyceryl
trinitrate (GTN) use as well as to investigate how patients commonly
store and carry their sublingual GTN tablets. Methodology: This was
a cross-sectional survey, using a validated researcher-administered
questionnaire. The study involved cardiac patients receiving
sublingual GTN attending the outpatient and inpatient departments of
Taiping Hospital, a non-academic public care hospital. The minimum
calculated sample size was 92, but 100 patients were conveniently
sampled. Respondents were interviewed on 3 areas, including
demographic data, knowledge and use of sublingual GTN. Eight
items were used to calculate each subject’s knowledge score and six
items were used to calculate use score. Results: Of the 96 patients
who consented to participate, majority (96.9%) were well aware of
the indication of sublingual GTN. With regards to the mechanism of
action of sublingual GTN, 73 (76%) patients did not know how the
medication works. Majority of the patients (66.7%) knew about the
proper storage of the tablet. In relation to the maximum number of
sublingual GTN tablets that can be taken during each angina episode,
36.5% did not know that up to 3 tablets of sublingual GTN can be
taken during each episode of angina. Fifty four (56.2%) patients were
not aware that they need to replace sublingual GTN every 8 weeks
after receiving the tablets. Majority (69.8%) of the patients
demonstrated lack of knowledge with regards to the use of sublingual
GTN as prevention of chest pain. Conclusion: Overall, patients’
knowledge regarding the self-administration of sublingual GTN is
still inadequate. The findings support the need for more frequent
reinforcement of patient education, especially in the areas of
preventive use, storage and drug stability.
Abstract: Attributes and methods are the basic contents of an
object-oriented class. The connectivity among these class members
and the relationship between the class and other classes play an
important role in determining the quality of an object-oriented
system. Class cohesion evaluates the degree of relatedness of class
attributes and methods, whereas class coupling refers to the degree to
which a class is related to other classes. Researchers have proposed
several class cohesion and class coupling measures. However, the
correlation between class coupling and class cohesion measures has
not been thoroughly studied. In this paper, using classes of three
open-source Java systems, we empirically investigate the correlation
between several measures of connectivity-based class cohesion and
coupling. Four connectivity-based cohesion measures and eight
coupling measures are considered in the empirical study. The
empirical study results show that class connectivity-based cohesion
and coupling internal quality attributes are inversely correlated. The
strength of the correlation depends highly on the cohesion and
coupling measurement approaches.
Abstract: New physical insights into the nonlinear Lorenz
equations related to flow resistance is discussed in this work. The
chaotic dynamics related to Lorenz equations has been studied in
many papers, which is due to the sensitivity of Lorenz equations to
initial conditions and parameter uncertainties. However, the physical
implication arising from Lorenz equations about convectional motion
attracts little attention in the relevant literature. Therefore, as a first
step to understand the related fluid mechanics of convectional motion,
this paper derives the Lorenz equations again with different forced
conditions in the model. Simulation work of the modified Lorenz
equations without the viscosity or buoyancy force is discussed. The
time-domain simulation results may imply that the states of the
Lorenz equations are related to certain flow speed and flow resistance.
The flow speed of the underlying fluid system increases as the flow
resistance reduces. This observation would be helpful to analyze the
coupling effects of different fluid parameters in a convectional model
in future work.
Abstract: This paper shows an experimental testing of a small
unit for combustion of solid fuels, such as charcoal and wood logs,
that can provide electricity. One of the concepts is that the unit does
not require qualified personnel for its operation. The unit itself is
composed of two main parts. The design requires a heat producing
stove and electricity producing thermoelectric generator. After the
construction the unit was tested and the results show that the
emission release is within the legislative requirements for emission
production and environmental protection. That qualifies such unit for
indoor application.
Abstract: Thin-walled elements with a matrix set on a base of
high-valuable Portland cement with dispersed reinforcement from
alkali-resistant glass fibres are used in a range of applications as
claddings of buildings and infrastructure constructions as well as
various architectural elements of residential buildings.
Even though their elementary thickness and therefore total weight
is quite low, architects and building companies demand on even
further decreasing of the bulk density of these fibre-cement elements
for the reason of loading elimination of connected superstructures
and easier assembling in demand conditions.
By the means of various kinds of light-weight aggregates it is
possible to achieve light-weighing of these composite elements.
From the range of possible fillers with different material properties
granulated expanded glass worked the best.
By the means of laboratory testing an effect of two fillers based on
expanded glass on the fibre reinforced cement composite was
verified.
Practical applicability was tested in the production of commonly
manufactured glass fibre reinforced concrete elements, such as
channels for electrical cable deposition, products for urban equipment
and especially various cladding elements.
Even though these are not structural elements, it is necessary to
evaluate also strength characteristics and resistance to environment
for their durability in certain applications.
Abstract: Bir El Djir is an important coastal township in Oran
department, located at 450 Km far away from Algiers on northwest of
Algeria. In this coastal area, the urban sprawl is one of the main
problems that reduce the limited highly fertile land. So, using the
remote sensing and GIS technologies have shown their great
capabilities to solve many earth resources issues.
The aim of this study is to produce land use and cover map for the
studied area at varied periods to monitor possible changes that may
occurred, particularly in the urban areas and subsequently predict
likely changes. For this, two spatial images SPOT and Landsat
satellites from 1987 and 2014 respectively were used to assess the
changes of urban expansion and encroachment during this period
with photo-interpretation and GIS approach.
The results revealed that the town of Bir El Djir has shown a
highest growth rate in the period 1987-2014 which is 1201.5 hectares
in terms of area. These expansions largely concern the new real estate
constructions falling within the social and promotional housing
programs launched by the government.
The most urban expansion is characterized by the new
construction in the form of spontaneous or peripheral precarious
habitat, but also unstructured slums settled especially in the
southeastern part of town.
Abstract: This article focuses on the issue of airport emergency
plans, which are documents describing reactions to events with
impact on aviation safety or aviation security. The article specifically
focuses on the use and creation of emergency plans, where could be
found a number of disagreements between different stakeholders, for
which the airport emergency plan applies. Those are the friction
surfaces of interfaces, which is necessary to identify and ensure them
smooth process to avoid dangerous situations or delay.
Abstract: Offering a Product-Service System (PSS) is a
well-accepted strategy that companies may adopt to provide a set of
systemic solutions to customers. PSSs were initially provided in a
simple form but now take diversified and complex forms involving
multiple services, products and technologies. With the growing
interest in the PSS, frameworks for the PSS development have been
introduced by many researchers. However, most of the existing
frameworks fail to examine various relations existing in a complex
PSS. Since designing a complex PSS involves full integration of
multiple products and services, it is essential to identify not only
product-service relations but also product-product/ service-service
relations. It is also equally important to specify how they are related
for better understanding of the system. Moreover, as customers tend to
view their purchase from a more holistic perspective, a PSS should be
developed based on the whole system’s requirements, rather than
focusing only on the product requirements or service requirements.
Thus, we propose a framework to develop a complex PSS that is
coordinated fully with the requirements of both worlds. Specifically,
our approach adopts a multi-domain matrix (MDM). A MDM
identifies not only inter-domain relations but also intra-domain
relations so that it helps to design a PSS that includes highly desired
and closely related core functions/ features. Also, various dependency
types and rating schemes proposed in our approach would help the
integration process.
Abstract: In the framework of the modernization of the city of
Constantine and in order to restore its status as a regional metropolis
introducing it into the network of cities international metropolises,
has major urban project was launched: project of modernization and
of metropolitanization of the city of Constantine.
Our research project focuses on the management of the project for
the modernization of the city of Constantine (PMMC) focusing on
the management of some aspects of the urban project whose
participation, with the objective assessment of the managerial
approach business.
In this contribution, we focus on two cases revealing taken into
account in our research work on the question of participation of
actors and their organizations. It is "the urban project of
modernization of Constantine" and the operation relating to "the
urban improvement in the city of the Brothers FERRAD in the
district of Zouaghi". This project and this operation with the objective
of improving the living conditions of citizens have faced several
challenges and obstacles that have been in major part the factors of its
failures.
Through this study, we examined the management process and the
mode of organization of the actors of the project as well as the level
of participation of the citizen to finally proposed managerial solutions
toconflict situations observed.
Abstract: The Malaysian government had consistently revived
its campaign for “Buy Malaysian Goods” from time to time. The
purpose of the campaign is to remind consumers to be ethnocentric
and patriotic when purchasing product and services. This is necessary
to ensure high demand for local products and services compared to
foreign products. However, the decline of domestic investment in
2012 has triggered concern for the Malaysian economy. Hence, this
study attempts to determine the drivers of actual purchasing behavior,
intention to purchase domestic products and ethnocentrism. The
study employs the cross-sectional primary data, self-administered on
household, selected using stratified random sampling in four
Malaysian regions. A nine factor driver of actual domestic purchasing
behavior (culture openness, conservatism, collectivism, patriotism,
control belief, interest in foreign travel, attitude, ethnocentrism and
intention) were measured utilizing 60 items, using 7-point Likertscale.
From 1000 questionnaires distributed, a sample of 486 were
returned representing 48.6 percent response rate. From the fit
generated structural model (SEM analysis), it was found that the
drivers of actual purchase behavior are collectivism, cultural
openness and patriotism; the drivers of intention to purchase
domestic product are attitude, control belief, collectivism and
conservatism; and drivers of ethnocentrism are cultural openness,
control belief, foreign travel and patriotism. It also shows that
Malaysian consumers scored high in ethnocentrism and patriotism.
The findings are discussed in the perspective of its implication to
Malaysian National Agenda.
Abstract: This work deals with parameter identification of
permanent magnet motors, a class of ac motor which is particularly
important in industrial automation due to characteristics like
applications high performance, are very attractive for applications
with limited space and reducing the need to eliminate because they
have reduced size and volume and can operate in a wide speed range,
without independent ventilation. By using experimental data and
genetic algorithm we have been able to extract values for both the
motor inductance and the electromechanical coupling constant, which
are then compared to measured and/or expected values.
Abstract: Over the past four decades, the fatigue behavior of
nickel-based alloys has been widely studied. However, in recent
years, significant advances in the fabrication process leading to grain
size reduction have been made in order to improve fatigue properties
of aircraft turbine discs. Indeed, a change in particle size affects the
initiation mode of fatigue cracks as well as the fatigue life of the
material. The present study aims to investigate the fatigue behavior of
a newly developed nickel-based superalloy under biaxial-planar
loading. Low Cycle Fatigue (LCF) tests are performed at different
stress ratios so as to study the influence of the multiaxial stress state
on the fatigue life of the material. Full-field displacement and strain
measurements as well as crack initiation detection are obtained using
Digital Image Correlation (DIC) techniques. The aim of this
presentation is first to provide an in-depth description of both the
experimental set-up and protocol: the multiaxial testing machine, the
specific design of the cruciform specimen and performances of the
DIC code are introduced. Second, results for sixteen specimens
related to different load ratios are presented. Crack detection, strain
amplitude and number of cycles to crack initiation vs. triaxial stress
ratio for each loading case are given. Third, from fractographic
investigations by scanning electron microscopy it is found that the
mechanism of fatigue crack initiation does not depend on the triaxial
stress ratio and that most fatigue cracks initiate from subsurface
carbides.
Abstract: The development of allometric models is crucial to
accurate forest biomass/carbon stock assessment. The aim of this
study was to develop a set of biomass prediction models that will
enable the determination of total tree aboveground biomass for
savannah woodland area in Niger State, Nigeria. Based on the data
collected through biometric measurements of 1816 trees and
destructive sampling of 36 trees, five species specific and one site
specific models were developed. The sample size was distributed
equally between the five most dominant species in the study site
(Vitellaria paradoxa, Irvingia gabonensis, Parkia biglobosa,
Anogeissus leiocarpus, Pterocarpus erinaceous). Firstly, the
equations were developed for five individual species. Secondly these
five species were mixed and were used to develop an allometric
equation of mixed species. Overall, there was a strong positive
relationship between total tree biomass and the stem diameter. The
coefficient of determination (R2 values) ranging from 0.93 to 0.99 P
< 0.001 were realised for the models; with considerable low standard
error of the estimates (SEE) which confirms that the total tree above
ground biomass has a significant relationship with the dbh. F-test
values for the biomass prediction models were also significant at p
Abstract: Robotic surgery is used to enhance minimally invasive
surgical procedure. It provides greater degree of freedom for surgical
tools but lacks of haptic feedback system to provide sense of touch to
the surgeon. Surgical robots work on master-slave operation, where
user is a master and robotic arms are the slaves. Current, surgical
robots provide precise control of the surgical tools, but heavily rely
on visual feedback, which sometimes cause damage to the inner
organs. The goal of this research was to design and develop a realtime
Simulink based robotic system to study force feedback
mechanism during instrument-object interaction. Setup includes three
VelmexXSlide assembly (XYZ Stage) for three dimensional
movement, an end effector assembly for forceps, electronic circuit for
four strain gages, two Novint Falcon 3D gaming controllers,
microcontroller board with linear actuators, MATLAB and Simulink
toolboxes. Strain gages were calibrated using Imada Digital Force
Gauge device and tested with a hard-core wire to measure
instrument-object interaction in the range of 0-35N. Designed
Simulink model successfully acquires 3D coordinates from two
Novint Falcon controllers and transfer coordinates to the XYZ stage
and forceps. Simulink model also reads strain gages signal through
10-bit analog to digital converter resolution of a microcontroller
assembly in real time, converts voltage into force and feedback the
output signals to the Novint Falcon controller for force feedback
mechanism. Experimental setup allows user to change forward
kinematics algorithms to achieve the best-desired movement of the
XYZ stage and forceps. This project combines haptic technology
with surgical robot to provide sense of touch to the user controlling
forceps through machine-computer interface.