Abstract: We derive simple sets of equations to describe the microwave response of a thin film of magnetized hydrogen plasma in the presence of carbon nanotubes, which were grown by ironcatalyzed high-pressure disproportionation (HiPco). By considering the interference effects due to multiple reflections between thin plasma film interfaces, we present the effects of the continuously changing external magnetic field and plasma parameters on the reflected power, absorbed power, and transmitted power in the system. The simulation results show that the interference effects play an important role in the reflectance, transmittance and absorptance of microwave radiation at the magnetized plasma slab. As a consequence, the interference effects lead to a sinusoidal variation of the reflected intensity and can greatly reduce the amount of reflection power, but the absorption power increases.
Abstract: Poly (ethylene glycol) (PEG) molecules attached to surfaces have shown high potential as a protein repellent due to their flexibility and highly water solubility. A quartz crystal microbalance recording frequency and dissipation changes (QCM-D) has been used to study the adsorption from aqueous solutions, of lysozyme and α-lactalbumin proteins (the last with and without calcium) onto modified stainless steel surfaces. Surfaces were coated with poly(ethylene imine) (PEI) and silicate before grafting on PEG molecules. Protein adsorption was also performed on the bare stainless steel surface as a control. All adsorptions were conducted at 23°C and pH 7.2. The results showed that the presence of PEG molecules significantly reduced the adsorption of lysozyme and α- lactalbumin (with calcium) onto the stainless steel surface. By contrast, and unexpected, PEG molecules enhanced the adsorption of α-lactalbumin (without calcium). It is suggested that the PEG -α- lactalbumin hydrophobic interaction plays a dominant role which leads to protein aggregation at the surface for this latter observation. The findings also lead to the general conclusion that PEG molecules are not a universal protein repellent. PEG-on-PEI surfaces were better at inhibiting the adsorption of lysozyme and α-lactalbumin (with calcium) than with PEG-on-silicate surfaces.
Abstract: Uncertainties of a serial production line affect on the
production throughput. The uncertainties cannot be prevented in a
real production line. However the uncertain conditions can be
controlled by a robust prediction model. Thus, a hybrid model
including autoregressive integrated moving average (ARIMA) and
multiple polynomial regression, is proposed to model the nonlinear
relationship of production uncertainties with throughput. The
uncertainties under consideration of this study are demand, breaktime,
scrap, and lead-time. The nonlinear relationship of production
uncertainties with throughput are examined in the form of quadratic
and cubic regression models, where the adjusted R-squared for
quadratic and cubic regressions was 98.3% and 98.2%. We optimized
the multiple quadratic regression (MQR) by considering the time
series trend of the uncertainties using ARIMA model. Finally the
hybrid model of ARIMA and MQR is formulated by better adjusted
R-squared, which is 98.9%.
Abstract: This paper deals with new concept of using compressed atmospheric air as a zero pollution power source for running motorbikes. The motorbike is equipped with an air turbine in place of an internal combustion engine, and transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor to casing diameter ratios with respect to different vane angles (number of vanes) have been considered and analyzed. It is found that the shaft work output is optimum for some typical values of rotor / casing diameter ratios at a particular value of vane angle (no. of vanes). In this study, the maximum power is obtained as 4.5kW - 5.3kW (5.5-6.25 HP) when casing diameter is taken 100 mm, and rotor to casing diameter ratios are kept from 0.65 to 0.55. This value of output is sufficient to run motorbike.
Abstract: As more people from non-technical backgrounds
are becoming directly involved with large-scale ontology
development, the focal point of ontology research has shifted
from the more theoretical ontology issues to problems
associated with the actual use of ontologies in real-world,
large-scale collaborative applications. Recently the National
Science Foundation funded a large collaborative ontology
development project for which a new formal ontology model,
the Ontology Abstract Machine (OAM), was developed to
satisfy some unique functional and data representation
requirements. This paper introduces the OAM model and the
related algorithms that enable maintenance of an ontology that
supports node-based user access. The successful software
implementation of the OAM model and its subsequent
acceptance by a large research community proves its validity
and its real-world application value.
Abstract: In this study, aeroelastic response and performance
analyses have been conducted for a 5MW-Class composite wind
turbine blade model. Advanced coupled numerical method based on
computational fluid dynamics (CFD) and computational flexible
multi-body dynamics (CFMBD) has been developed in order to
investigate aeroelastic responses and performance characteristics of
the rotating composite blade. Reynolds-Averaged Navier-Stokes
(RANS) equations with k-ω SST turbulence model were solved for
unsteady flow problems on the rotating turbine blade model. Also,
structural analyses considering rotating effect have been conducted
using the general nonlinear finite element method. A fully implicit
time marching scheme based on the Newmark direct integration
method is applied to solve the coupled aeroelastic governing equations
of the 3D turbine blade for fluid-structure interaction (FSI) problems.
Detailed dynamic responses and instantaneous velocity contour on the
blade surfaces which considering flow-separation effects were
presented to show the multi-physical phenomenon of the huge rotating
wind- turbine blade model.
Abstract: Discovering new biological knowledge from the highthroughput biological data is a major challenge to bioinformatics today. To address this challenge, we developed a new approach for protein classification. Proteins that are evolutionarily- and thereby functionally- related are said to belong to the same classification. Identifying protein classification is of fundamental importance to document the diversity of the known protein universe. It also provides a means to determine the functional roles of newly discovered protein sequences. Our goal is to predict the functional classification of novel protein sequences based on a set of features extracted from each protein sequence. The proposed technique used datasets extracted from the Structural Classification of Proteins (SCOP) database. A set of spectral domain features based on Fast Fourier Transform (FFT) is used. The proposed classifier uses multilayer back propagation (MLBP) neural network for protein classification. The maximum classification accuracy is about 91% when applying the classifier to the full four levels of the SCOP database. However, it reaches a maximum of 96% when limiting the classification to the family level. The classification results reveal that spectral domain contains information that can be used for classification with high accuracy. In addition, the results emphasize that sequence similarity measures are of great importance especially at the family level.
Abstract: This research project is developed in order to study
managerial styles of modern Thai executives. The thorough
understanding will lead to continuous improvement and efficient
performance of Thai business organizations. Regarding managerial
skills, Thai executives focus heavily upon human skills. Also, the
negotiator roles are most emphasis in their management. In addition,
Thai executives pay most attention to the fundamental management
principles including Harmony and Unity of Direction of the
organizations. Moreover, the management techniques, consisting of
Team work and Career Planning are of their main concern. Finally,
Thai executives wish to enhance their firms- image and employees-
morale through conducting the ethical and socially responsible
activities. The major tactic deployed to stimulate employees- ethical
behaviors and mindset is Code of Ethics development.
Abstract: Maize and Indian mustard are significant crops in
semi-arid climate zones of India. Improved water management
requires precise scheduling of irrigation, which in turn requires an
accurate computation of daily crop evapotranspiration (ETc). Daily
crop evapotranspiration comes as a product of reference
evapotranspiration (ET0) and the growth stage specific crop
coefficients modified for daily variation. The first objective of
present study is to develop crop coefficients Kc for Maize and Indian
mustard. The estimated values of Kc for maize at the four crop
growth stages (initial, development, mid-season, and late season) are
0.55, 1.08, 1.25, and 0.75, respectively, and for Indian mustard the Kc
values at the four growth stages are 0.3, 0.6, 1.12, and 0.35,
respectively. The second objective of the study is to compute daily
crop evapotranspiration from ET0 and crop coefficients. Average
daily ETc of maize varied from about 2.5 mm/d in the early growing
period to > 6.5 mm/d at mid season. The peak ETc of maize is 8.3
mm/d and it occurred 64 days after sowing at the reproductive growth
stage when leaf area index was 4.54. In the case of Indian mustard,
average ETc is 1 mm/d at the initial stage, >1.8 mm/d at mid season
and achieves a peak value of 2.12 mm/d on 56 days after sowing.
Improved schedules of irrigation have been simulated based on daily
crop evapo-transpiration and field measured data. Simulation shows a
close match between modeled and field moisture status prevalent
during crop season.
Abstract: The approach proposed here is oriented in the direction of fuzzy system for the analysis and the synthesis of intelligent climate controllers, the simulation of the internal climate of the greenhouse is achieved by a linear model whose coefficients are obtained by identification. The use of fuzzy logic controllers for the regulation of climate variables represents a powerful way to minimize the energy cost. Strategies of reduction and optimization are adopted to facilitate the tuning and to reduce the complexity of the controller.
Abstract: Renewed interest in propeller propulsion on aircraft
configurations combined with higher propeller loads lead to the question how the effects of the propulsion on model support disturbances
should be accounted for. In this paper, the determination of engine power effects on support interference of sting-mounted models is
demonstrated by a measurement on a four-engine turboprop aircraft.
CFD results on a more generic model are presented in order to clarify
the possible mechanism behind engine power effects on support
interference. The engine slipstream induces a local change in angle
of sideslip at the model sting thereby influencing the sting near-field and far-field effects. Whether or not the net result of these changes
in the disturbance pattern leads to a significant engine power effect depends on the configuration of the wind tunnel model and the test
setup.
Abstract: This paper presented two new efficient algorithms
for contour approximation. The proposed algorithm is compared
with Ramer (good quality), Triangle (faster) and Trapezoid (fastest)
in this work; which are briefly described. Cartesian co-ordinates of
an input contour are processed in such a manner that finally
contours is presented by a set of selected vertices of the edge of the
contour. In the paper the main idea of the analyzed procedures for
contour compression is performed. For comparison, the mean
square error and signal-to-noise ratio criterions are used.
Computational time of analyzed methods is estimated depending on
a number of numerical operations. Experimental results are
obtained both in terms of image quality, compression ratios, and
speed. The main advantages of the analyzed algorithm is small
numbers of the arithmetic operations compared to the existing
algorithms.
Abstract: In a liberalized electricity market, it is not surprising
that different customers require different power quality (PQ) levels at
different price. Power quality related to several power disturbances is
described by many parameters, so how to define a comprehensive
hierarchy evaluation system of power quality (PQCHES) has become
a concerned issue. In this paper, based on four electromagnetic
compatibility (EMC) levels, the numerical range of each power
disturbance is divided into five grades (Grade I –Grade V), and the
“barrel principle" of power quality is used for the assessment of
overall PQ performance with only one grade indicator. A case study
based on actual monitored data of PQ shows that the site PQ grade
indicates the electromagnetic environment level and also expresses the
characteristics of loads served by the site.
The shortest plank principle of PQ barrel is an incentive
mechanism, which can combine with the rewards/penalty mechanism
(RPM) of consumed energy “on quality demand", to stimulate utilities
to improve the overall PQ level and also stimulate end-user more
“smart" under the infrastructure of future SmartGrid..
Abstract: This paper proposes the method combining artificial
neural network (ANN) with particle swarm optimization (PSO) to
implement the maximum power point tracking (MPPT) by controlling
the rotor speed of the wind generator. First, the measurements of wind
speed, rotor speed of wind power generator and output power of wind
power generator are applied to train artificial neural network and to
estimate the wind speed. Second, the method mentioned above is
applied to estimate and control the optimal rotor speed of the wind
turbine so as to output the maximum power. Finally, the result reveals
that the control system discussed in this paper extracts the maximum
output power of wind generator within the short duration even in the
conditions of wind speed and load impedance variation.
Abstract: The experiment was then conducted to investigate the
effect of cassava peel addition in the concentrate on the performance
of lactating dairy cows. Twenty four Holstein Friesian crossbred
(>87.5% Holstein Friesian) lactating dairy cows in mid lactation;
averaging 12.2+2.1 kg of milk, 119+45 days in milk, 44.1+6.2
months old and 449+33 kg live weight, were stratified for milk yield,
days in milk, age, stage of lactation and body weight, and then
randomly allocated to three treatment groups. The first, second and
third groups were fed concentrates containing the respective cassava
peel, 0, 20 and 40%. All cows were fed ad libitum corn silage and
freely access to clean water. Dry matter intake, 4%FCM, milk
composition and body weight change were affected (P
Abstract: Information Technology (IT) projects are always
accompanied by various risks and because of high rate of failure in
such projects, managing risks in order to neutralize or at least
decrease their effects on the success of the project is strongly
essential. In this paper, fuzzy analytical hierarchy process (FAHP) is
exploited as a means of risk evaluation methodology to prioritize and
organize risk factors faced in IT projects. A real case of IT projects, a
project of design and implementation of an integrated information
system in a vehicle producing company in Iran is studied. Related
risk factors are identified and then expert qualitative judgments about
these factors are acquired. Translating these judgments to fuzzy
numbers and using them as an input to FAHP, risk factors are then
ranked and prioritized by FAHP in order to make project managers
aware of more important risks and enable them to adopt suitable
measures to deal with these highly devastative risks.
Abstract: This study was conducted to determine the
effect of abdominal exercises versus abdominal supporting
belt on abdominal efficiency and inter-recti separation
following vaginal delivery.30 primiparous post-natal women
participated in this study. Their age ranged from (25 - 35)
years and their BMI < 30 Kg/m2. Participants were assigned
randomly into 2groups, participants of group (A) used
abdominal belt from the 2nd day following delivery, till the end
of puerperium (6 weeks), while participants of group (B)
engaged into abdominal exercises program from the 2nd day
following delivery for 6 weeks. The results of the present
study revealed that although there was no statistical difference
in waist circumference between both groups, participation in
abdominal exercise program produced a pronounced reduction
in waist/hip ratio, and inter-recti separation and also caused
significant increase in abdominal muscles strength (peak
torque, maximum repetition total work and average power)
higher than the use of abdominal belt.
Abstract: The role of neighborhood center as semi public (the
balance space) is disappeared in bonding between private and public
in new urbanism. In this way, a hierarchical principle in the
traditional neighborhood center appears to create or develop the
conditions for residents` relationships and belonging. This paper
evaluates significant of hierarchical principles of the neighborhood
center in residents` territoriality and its factors. In this way Miandeh
neighborhood center from Boshrooyeh city was determined as a case
study area. Results indicated that a hierarchical principle is the best
instrument to improve the territoriality as the subcomponent of place
belonging in residents. The findings help the urban designer to
revitalization the neighborhoods and proceedings in organization of
physical space.
Abstract: Self-compacting concrete (SCC), a new kind of high
performance concrete (HPC) have been first developed in Japan in
1986. The development of SCC has made casting of dense
reinforcement and mass concrete convenient, has minimized noise.
Fresh self-compacting concrete (SCC) flows into formwork and
around obstructions under its own weight to fill it completely and
self-compact (without any need for vibration), without any
segregation and blocking. The elimination of the need for
compaction leads to better quality concrete and substantial
improvement of working conditions. SCC mixes generally have a
much higher content of fine fillers, including cement, and produce
excessively high compressive strength concrete, which restricts its
field of application to special concrete only. To use SCC mixes in
general concrete construction practice, requires low cost materials to
make inexpensive concrete.
Rice husk ash (RHA) has been used as a highly reactive
pozzolanic material to improve the microstructure of the interfacial
transition zone (ITZ) between the cement paste and the aggregate in
self compacting concrete. Mechanical experiments of RHA blended
Portland cement concretes revealed that in addition to the pozzolanic
reactivity of RHA (chemical aspect), the particle grading (physical
aspect) of cement and RHA mixtures also exerted significant
influences on the blending efficiency.
The scope of this research was to determine the usefulness of Rice
husk ash (RHA) in the development of economical self compacting
concrete (SCC). The cost of materials will be decreased by reducing
the cement content by using waste material like rice husk ash instead
of.
This paper presents a study on the development of Mechanical
properties up to 180 days of self compacting and ordinary concretes
with rice-husk ash (RHA), from a rice paddy milling industry in
Rasht (Iran). Two different replacement percentages of cement by
RHA, 10%, and 20%, and two different water/cementicious material
ratios (0.40 and 0.35), were used for both of self compacting and
normal concrete specimens. The results are compared with those of
the self compacting concrete without RHA, with compressive,
flexural strength and modulus of elasticity. It is concluded that RHA
provides a positive effect on the Mechanical properties at age after
60 days.
Base of the result self compacting concrete specimens have higher
value than normal concrete specimens in all test except modulus of
elasticity. Also specimens with 20% replacement of cement by RHA
have the best performance.
Abstract: This paper focuses on robust design and optimization
of industrial production wastes. Past literatures were reviewed to case
study Clamason Industries Limited (CIL) - a leading ladder-tops
manufacturer. A painstaking study of the firm-s practices at the shop
floor revealed that Over-production, Waiting time, Excess inventory,
and Defects are the major wastes that are impeding their progress and
profitability. Design expert8 software was used to apply Taguchi
robust design and response surface methodology in order to model,
analyse and optimise the wastes cost in CIL. Waiting time and overproduction
rank first and second in contributing to the costs of wastes
in CIL. For minimal wastes cost the control factors of overproduction,
waiting-time, defects and excess-inventory must be set at
0.30, 390.70, 4 and 55.70 respectively for CIL. The optimal value of
cost of wastes for the months studied was 22.3679. Finally, a
recommendation was made that for the company to enhance their
profitability and customer satisfaction, they must adopt the Shingeo
Shingo-s Single Minute Exchange of Dies (SMED), which will
immediately tackle the waste of waiting by drastically reducing their
setup time.