Abstract: The purposes of this research are: 1) to study the media
literacy of early teenagers, and 2) to study the interaction between
gender and timing of media exposure that affects the media literacy
of teenagers. The sample of the study included 400 young people
aged between 11 to 17 and who were living in Bangkok. The data
was collected using questionnaires. Two-way ANOVA was used in
analyzing the collected data. The result revealed that gender and
timing of media exposure affected the media literacy of early
teenagers with statistical significance at the level of 0.05.
Abstract: A simple method for the simultaneous determination
of hippuric acid and benzoic acid in urine using reversed-phase high
performance liquid chromatography was described. Chromatography
was performed on a Nova-Pak C18 (3.9 x 150 mm) column with a
mobile phase of mixed solution methanol: water: acetic acid
(20:80:0.2) and UV detection at 254 nm. The calibration curve was
linear within concentration range at 0.125 to 6.0 mg/ml of hippuric
acid and benzoic acid. The recovery, accuracy and coefficient
variance of hippuric acid were 104.54%, 0.2% and 0.2% respectively
and for benzoic acid were 98.48%, 1.25% and 0.60% respectively.
The detection limit of this method was 0.01ng/l for hippuric acid and
0.06ng/l for benzoic acid. This method has been applied to the
analysis of urine samples from the suspected of toluene abuser or
glue sniffer among secondary school students at Johor Bahru.
Abstract: This paper presents a new fingerprint coding technique
based on contourlet transform and multistage vector quantization.
Wavelets have shown their ability in representing natural images that
contain smooth areas separated with edges. However, wavelets
cannot efficiently take advantage of the fact that the edges usually
found in fingerprints are smooth curves. This issue is addressed by
directional transforms, known as contourlets, which have the
property of preserving edges. The contourlet transform is a new
extension to the wavelet transform in two dimensions using
nonseparable and directional filter banks. The computation and
storage requirements are the major difficulty in implementing a
vector quantizer. In the full-search algorithm, the computation and
storage complexity is an exponential function of the number of bits
used in quantizing each frame of spectral information. The storage
requirement in multistage vector quantization is less when compared
to full search vector quantization. The coefficients of contourlet
transform are quantized by multistage vector quantization. The
quantized coefficients are encoded by Huffman coding. The results
obtained are tabulated and compared with the existing wavelet based
ones.
Abstract: International markets driven forces are changing
continuously, therefore companies need to gain a competitive edge in
such markets. Improving the company's products, processes and
practices is no longer auxiliary. Lean production is a production
management philosophy that consolidates work tasks with minimum
waste resulting in improved productivity. Lean production practices
can be mapped into many production areas. One of these is
Manufacturing Equipment and Technology (MET). Many lean
production practices can be implemented in MET, namely, specific
equipment configurations, total preventive maintenance, visual
control, new equipment/ technologies, production process
reengineering and shared vision of perfection.The purpose of this
paper is to investigate the implementation level of these six practices
in Jordanian industries. To achieve that a questionnaire survey has
been designed according to five-point Likert scale. The questionnaire
is validated through pilot study and through experts review. A sample
of 350 Jordanian companies were surveyed, the response rate was
83%. The respondents were asked to rate the extent of
implementation for each of practices. A relationship conceptual
model is developed, hypotheses are proposed, and consequently the
essential statistical analyses are then performed. An assessment tool
that enables management to monitor the progress and the
effectiveness of lean practices implementation is designed and
presented. Consequently, the results show that the average
implementation level of lean practices in MET is 77%, Jordanian
companies are implementing successfully the considered lean
production practices, and the presented model has Cronbach-s alpha
value of 0.87 which is good evidence on model consistency and
results validation.
Abstract: This study, focusing on the importance of encouraging
outdoor activities for children, aims to propose and implement a Web-GIS based outdoor education program for junior high schools,
which will then be evaluated by users. Specifically, for the purpose of improved outdoor activities in the junior high school education, the
outdoor education program, with chiefly using the Web-GIS that provides a good information provision and sharing tool, is proposed
and implemented before being evaluated by users. The conclusion of
this study can be summarized in the following two points.
(1) A five -step outdoor education program based on Web-GIS was
proposed for a “second school" at junior high schools that was then implemented before being evaluated by teachers as users.
(2) Based on the results of evaluation by teachers, it was clear that the general operation of Web-GIS based outdoor education program with them only is difficult due to their lack of knowledge regarding Web-GIS and that support staff who can effectively utilize Web-GIS are essential.
Abstract: Self-organizing map (SOM) provides both clustering and visualization capabilities in mining data. Dynamic self-organizing maps such as Growing Self-organizing Map (GSOM) has been developed to overcome the problem of fixed structure in SOM to enable better representation of the discovered patterns. However, in mining large datasets or historical data the hierarchical structure of the data is also useful to view the cluster formation at different levels of abstraction. In this paper, we present a technique to generate concept trees from the GSOM. The formation of tree from different spread factor values of GSOM is also investigated and the quality of the trees analyzed. The results show that concept trees can be generated from GSOM, thus, eliminating the need for re-clustering of the data from scratch to obtain a hierarchical view of the data under study.
Abstract: Biodiesel is traditionally produced from oleaginous
plants. On the other hand, increasing biodiesel production from these
raw materials could create problems of food supply. Producing
biodiesel from microalgae could help to overcome this difficulty,
because microalgae are rich in lipids and do not compete for arable
lands. However, no studies had compared vegetable and microalgae
oil-based biodiesel in terms of yield, viscosity and heat of
combustion. In the present study, commercial canola and microalgae
oil were therefore transesterified with methanol under a homogenous
alkali catalyst (potassium hydroxide) at 100oC for 1h. The result
showed that microalgae-based oil has a higher yield in biodiesel with
89.7% (g biodiesel/g oil) and a lower kinematic viscosity (22oC) of
4.31 mm/s2 than canola oil.
Abstract: Vermicomposting is the conversion of organic waste
into bio-fertilizers through the action of earthworm. This technology
is widely used for organic solid waste management. Waste corn pulp
blended with cow dung manure was vermicomposted over 30 days
using Eisenia fetida earthworms species. pH, temperature, moisture
content, and electrical conductivity were daily monitored. The
feedstock, vermicompost and vermiwash were analyzed for nutrient
composition. The average temperature and moisture content in the
vermi-reactor was 22.5°C and 42.5% respectively. The vermicompost
and vermiwash had an almost neutral pH whilst the electrical
conductivity was 21% higher in the vermicompost. The nitrogen and
potassium content was 57% and 79.6% richer in the vermicompost
respectively compared to the vermiwash. However, the vermiwash
was 84% richer in phosphorous as compared to vermicompost.
Furthermore, the vermiwash was 89.1% and 97.6% richer in Ca and
Mg respectively and was 97.8% richer in Na salts compared to the
vermicompost. The vermiwash also indicated a significantly higher
amount of micronutrients. Both bio-fertilizers were rich in nutrients
specification for fertilizers.
Abstract: Sedimentation formation is a complex hydraulic phenomenon that has emerged as a major operational and maintenance consideration in modern hydraulic engineering in general and river engineering in particular. Sediments accumulation along the river course and their eventual storage in a form of islands affect water intake in the canal systems that are fed by the storage reservoirs. Without proper management, sediment transport can lead to major operational challenges in water distribution system of arid regions like the Dez and Hamidieh command areas. The paper aims to investigate sedimentation in the Western Canal of Dez Diversion Weir using the SHARC model and compare the results with the two intake structures of the Hamidieh dam in Iran using SSIIM model. The objective was to identify the factors which influence the process, check reliability of outcome and provide ways in which to mitigate the implications on operation and maintenance of the structures. Results estimated sand and silt bed loads concentrations to be 193 ppm and 827ppm respectively. This followed ,ore or less similar pattern in Hamidieh where the sediment formation impeded water intake in the canal system. Given the available data on average annual bed loads and average suspended sediment loads of 165ppm and 837ppm in the Dez, there was a significant statistical difference (16%) between the sand grains, whereas no significant difference (1.2%) was find in the silt grain sizes. One explanation for such finding being that along the 6 Km river course there was considerable meandering effects which explains recent shift in the hydraulic behavior along the stream course under investigation. The sand concentration in downstream relative to present state of the canal showed a steep descending curve. Sediment trapping on the other hand indicated a steep ascending curve. These occurred because the diversion weir was not considered in the simulation model. The comparative study showed very close similarities in the results which explains the fact that both software can be used as accurate and reliable analytical tools for simulation of the sedimentation in hydraulic engineering.
Abstract: Scouring around a bridge pier is a complex
phenomenon. More laboratory experiments are required to
understand the scour mechanism. This paper focused on time
development of local scour around piers and piles in semi integral
bridges. Laboratory data collected at Hydraulics Laboratory,
University of Malaya was analyzed for this purpose. Tests were
performed with two different uniform sediment sizes and five ranges
of flow velocities. Fine and coarse sediments were tested in the
flume. Results showed that scour depths for both pier and piles
increased with time up to certain levels and after that they became
almost constant. It had been found that scour depths increased when
discharges increased. Coarser sediment also produced lesser scouring
at the piers and combined piles.
Abstract: This paper considers the exclusion of consumer rights by the New Zealand Consumer Guarantees Act 1993 in eauctions. The paper asserts that the absence of an individual auctioneer conducting each e-auction means that e-auctions may not be auctions at all. The paper also questions the justification for excluding consumer rights in e-auctions because the rationale for excluding consumer rights in traditional auctions does not fit with e-auctions due to the significant differences in the sale processes. The paper recommends reform by way of statutory amendment.
Abstract: A complete CAD procedure to model a twisted-bladed
vertical-axis wind turbine (VAWT) is presented with the aim of
determining some practical guidelines to be used for the generation
of an easily-meshable CAD geometry to be adopted as the basis of
both CFD and FEM numerical simulations.
Abstract: Swarm principles are increasingly being used to design controllers for the coordination of multi-robot systems or, in general, multi-agent systems. This paper proposes a two-dimensional Lagrangian swarm model that enables the planar agents, modeled as point masses, to swarm whilst effectively avoiding each other and obstacles in the environment. A novel method, based on an extended Lyapunov approach, is used to construct the model. Importantly, the Lyapunov method ensures a form of practical stability that guarantees an emergent behavior, namely, a cohesive and wellspaced swarm with a constant arrangement of individuals about the swarm centroid. Computer simulations illustrate this basic feature of collective behavior. As an application, we show how multiple planar mobile unicycle-like robots swarm to eventually form patterns in which their velocities and orientations stabilize.
Abstract: The task of face recognition has been actively
researched in recent years. This paper provides an up-to-date review of major human face recognition research. We first present an
overview of face recognition and its applications. Then, a literature review of the most recent face recognition techniques is presented.
Description and limitations of face databases which are used to test
the performance of these face recognition algorithms are given. A
brief summary of the face recognition vendor test (FRVT) 2002, a
large scale evaluation of automatic face recognition technology, and
its conclusions are also given. Finally, we give a summary of the research results.
Abstract: A generalized unified power quality conditioner
(GUPQC) by using three single-phase three-level voltage source
converters (VSCs) connected back-to-back through a common dc
link is proposed in this paper as a new custom power device for a
three-feeder distribution system. One of the converters is connected
in shunt with one feeder for mitigation of current harmonics and
reactive power compensation, while the other two VSCs are
connected in series with the other two feeders to maintain the load
voltage sinusoidal and at constant level. A new control scheme based
on synchronous reference frame is proposed for series converters.
The simulation analysis on compensation performance of GUPQC
based on PSCAD/EMTDC is reported.
Abstract: This paper presents a new algorithm for the channel estimation of the OFDM system based on a pilot signal for the new generation of high data rate communication systems. In orthogonal frequency division multiplexing (OFDM) systems over fast-varying fading channels, channel estimation and tracking is generally carried out by transmitting known pilot symbols in given positions of the frequency-time grid. In this paper, we propose to derive an improved algorithm based on the calculation of the mean and the variance of the adjacent pilot signals for a specific distribution of the pilot signals in the OFDM frequency-time grid then calculating of the entire unknown channel coefficients from the equation of the mean and the variance. Simulation results shows that the performance of the OFDM system increase as the length of the channel increase where the accuracy of the estimated channel will be increased using this low complexity algorithm, also the number of the pilot signal needed to be inserted in the OFDM signal will be reduced which lead to increase in the throughput of the signal over the OFDM system in compared with other type of the distribution such as Comb type and Block type channel estimation.
Abstract: The technological concepts such as wireless hospital
and portable cardiac telemetry system require the development of
physiological signal acquisition devices to be easily integrated into
the hospital database. In this paper we present the low cost, portable
wireless ECG acquisition hardware that transmits ECG signals to a
dedicated computer.The front end of the system obtains and
processes incoming signals, which are then transmitted via a
microcontroller and wireless Bluetooth module. A monitoring
purpose Bluetooth based end user application integrated with patient
database management module is developed for the computers. The
system will act as a continuous event recorder, which can be used to
follow up patients who have been resuscitatedfrom cardiac arrest,
ventricular tachycardia but also for diagnostic purposes for patients
with arrhythmia symptoms. In addition, cardiac information can be
saved into the patient-s database of the hospital.
Abstract: We review a knowledge extractor model in
constructing 3G Killer Applications. The success of 3G is essential
for Government as it became part of Telecommunications National
Strategy. The 3G wireless technologies may reach larger area and
increase country-s ICT penetration. In order to understand future
customers needs, the operators require proper information
(knowledge) lying inside. Our work approached future customers as
complex system where the complex knowledge may expose regular
behavior. The hidden information from 3G future customers is
revealed by using fractal-based questionnaires. Afterward, further
statistical analysis is used to match the results with operator-s
strategic plan. The developments of 3G applications also consider its
saturation time and further improvement of the application.
Abstract: Malting is usually carried out on intact barley seed,
while hull is still attached to it. In this study, oat grain with and
without hull was subjected to controlled germination to optimize its
enzymes activity, in such a way that lipase has the lowest and α-
amylase and proteinase the highest activities. Since pH has a great
impact on the activity of the enzymes, the pH of germination media
was set up to 3 to 8. In dehulled oats, lipase and α-amylase had the
lowest and highest activities in pHs 3 and 6, respectively whereas the
highest proteinase activity was evidenced at pH 7 and 4 in the oats
with and without hull respectively. While measurements indicated
that the effect of hull on the enzyme activities particularly in lipase
and amylase at each level of the pH are significantly different, the
best results were obtained in those samples in which their hull had
been removed. However, since the similar lipase activity in
germinated dehulled oat were recorded at the pHs 4 and 5, therefore
it was concluded that pH 5 in dehulled oat seed may provide the
optimum enzyme activity for all the enzymes.
Abstract: The techniques for estimating the adhesive and cohesive strength in high velocity oxy fuel (HVOF) thermal spray coatings have been discussed and compared. The development trend and the last investigation have been studied. We will focus on benefits and limitations of these methods in different process and materials.