Abstract: Nine Degrees of Freedom (9 DOF) systems are
already in development in many areas. In this paper, an integrated
pressure sensor is proposed that will make use of an already existing
monolithic 9 DOF inertial MEMS platform. Capacitive pressure
sensors can suffer from limited sensitivity for a given size of
membrane. This novel pressure sensor design increases the sensitivity
by over 5 times compared to a traditional array of square diaphragms
while still fitting within a 2 mm x 2 mm chip and maintaining a fixed
static capacitance. The improved design uses one large diaphragm
supported by pillars with fixed electrodes placed above the areas of
maximum deflection. The design optimization increases the
sensitivity from 0.22 fF/kPa to 1.16 fF/kPa. Temperature sensitivity
was also examined through simulation.
Abstract: The purpose of this project is to propose a quick and
environmentally friendly alternative to measure the quality of oils
used in food industry. There is evidence that repeated and
indiscriminate use of oils in food processing cause physicochemical
changes with formation of potentially toxic compounds that can
affect the health of consumers and cause organoleptic changes. In
order to assess the quality of oils, non-destructive optical techniques
such as Interferometry offer a rapid alternative to the use of reagents,
using only the interaction of light on the oil. Through this project, we
used interferograms of samples of oil placed under different heating
conditions to establish the changes in their quality. These
interferograms were obtained by means of a Mach-Zehnder
Interferometer using a beam of light from a HeNe laser of 10mW at
632.8nm. Each interferogram was captured, analyzed and measured
full width at half-maximum (FWHM) using the software from
Amcap and ImageJ. The total of FWHMs was organized in three
groups. It was observed that the average obtained from each of the
FWHMs of group A shows a behavior that is almost linear, therefore
it is probable that the exposure time is not relevant when the oil is
kept under constant temperature. Group B exhibits a slight
exponential model when temperature raises between 373 K and 393
K. Results of the t-Student show a probability of 95% (0.05) of the
existence of variation in the molecular composition of both samples.
Furthermore, we found a correlation between the Iodine Indexes
(Physicochemical Analysis) and the Interferograms (Optical
Analysis) of group C. Based on these results, this project highlights
the importance of the quality of the oils used in food industry and
shows how Interferometry can be a useful tool for this purpose.
Abstract: Sustainability is a very important and heavily
discussed subject, expanding through tourism as well. The study
proposition was to collect data and present it to the competent bodies
so they can mold their public policies to improve the conditions of
the site. It was hypothesized that the lack of data is currently
affecting the quality of life and the sustainable development of the
site and the tourism. The research was held in Mateiros, a city in the
state of Tocantins (TO)/Brasil near Palmas, its capital city. Because
of the concentration of tourists during the high season and several
tourist attractions being around, the research took place in Mateiros.
The methodological procedure had a script of theoretical construction
and investigation of the deductive scientific method parameters
through a case study in the Jalapão/TO/Brazil region, using it as a
tool for a questionnaire given to the competent bodies in an interview
system with the UN sustainability indexes as a base. In the three
sustainable development scope: environmental, social and economic,
the results indicated that the data presented by the interviewed were
scarce or nonexistent. It shows that more research is necessary,
providing the tools for the ones responsible to propose action plans to
improve the site, strengthening the tourism and making it even more
sustainable.
Abstract: A robust sequential nonparametric method is proposed
for adaptation to background noise parameters for real-time. The
distribution of background noise was modelled like to Huber
contamination mixture. The method is designed to operate as an
adaptation-unit, which is included inside a detection subsystem of an
integrated multichannel monitoring system. The proposed method
guarantees the given size of a nonasymptotic confidence set for noise
parameters. Properties of the suggested method are rigorously
proved. The proposed algorithm has been successfully tested in real
conditions of a functioning C-OTDR monitoring system, which was
designed to monitor railways.
Abstract: The causality between energy consumption and
economic growth has been an important issue in the economic
literature. This paper studies the causal relationship between
electricity consumption and economic growth in Mexico for the
period of 1971-2011. In so doing, unit root and causality tests are
applied. The results show that energy consumption and economic
growth series are stationary and there is also a causality relationship
running from economic growth to electricity consumption. Therefore,
any energy conservation policy would have little or no impact at all
on economic growth in México.
Abstract: Present work deals with the possible use of fertigation
in agriculture and its impact on the availability of mineral nitrogen
(Nmin) in topsoil and subsoil horizons. The aim of the present study is
to demonstrate the effect of the organic matter presence in fertigation
on microbial transformation and availability of mineral nitrogen
forms. The main investigation reason is the potential use of pretreated
waste water, as a source of organic carbon (Corg) and residual
nutrients (Nmin) for fertigation. Laboratory experiment has been
conducted to demonstrate the effect of the arable land fertilization
method on the Nmin availability in different depths of the soil with
the usage of model experimental containers filled with soil from
topsoil and podsoil horizons that were taken from the precise area.
Tufted hairgrass (Deschampsia caespitosa) has been chosen as a
model plant. The water source protection zone Brezova nad Svitavou
has been a research area where significant underground reservoirs of
drinking water of the highest quality are located. From the second
half of the last century local sources of drinking water show
nitrogenous compounds increase that get here almost only from
arable lands. Therefore, an attention of the following text focuses on
the fate of mineral nitrogen in the complex plant-soil. Research
results show that the fertigation application with Corg in a
combination with mineral fertilizer can reduce the amount of Nmin
leached from topsoil horizon of agricultural soils. In addition, some
plants biomass production reduces may occur.
Abstract: This paper is focused on the reference current
calculation in the compensation mode of the active DC traction
substations. The so-called p-q theory of the instantaneous reactive
power is used as theoretical foundation. The compensation goal of
total compensation is taken into consideration for the operation under
both sinusoidal and nonsinusoidal voltage conditions, through the
two objectives of unity power factor and perfect harmonic
cancelation. Four blocks of reference current generation implement
the conceived algorithms and they are included in a specific Simulink
library, which is useful in a DSP dSPACE-based platform working
under Matlab/Simulink. The simulation results validate the
correctness of the implementation and fulfillment of the
compensation tasks.
Abstract: The work aims to develop a robot in the form of
autonomous vehicle to detect, inspection and mapping of
underground pipelines through the ATmega328 Arduino platform.
Hardware prototyping is very similar to C / C ++ language that
facilitates its use in robotics open source, resembles PLC used in
large industrial processes. The robot will traverse the surface
independently of direct human action, in order to automate the
process of detecting buried pipes, guided by electromagnetic
induction. The induction comes from coils that send the signal to the
Arduino microcontroller contained in that will make the difference in
intensity and the treatment of the information, and then this
determines actions to electrical components such as relays and
motors, allowing the prototype to move on the surface and getting the
necessary information. This change of direction is performed by a
stepper motor with a servo motor. The robot was developed by
electrical and electronic assemblies that allowed test your application.
The assembly is made up of metal detector coils, circuit boards and
microprocessor, which interconnected circuits previously developed
can determine, process control and mechanical actions for a robot
(autonomous car) that will make the detection and mapping of buried
pipelines plates. This type of prototype can prevent and identifies
possible landslides and they can prevent the buried pipelines suffer an
external pressure on the walls with the possibility of oil leakage and
thus pollute the environment.
Abstract: A knowledge base stores facts and rules about the
world that applications can use for the purpose of reasoning. By
applying the concept of granular computing to a knowledge base,
several advantages emerge. These can be harnessed by applications
to improve their capabilities and performance. In this paper, the
concept behind such a construct, called a granular knowledge cube,
is defined, and its intended use as an instrument that manages to
cope with different data types and detect knowledge domains is
elaborated. Furthermore, the underlying architecture, consisting of the
three layers of the storing, representing, and structuring of knowledge,
is described. Finally, benefits as well as challenges of deploying it
are listed alongside application types that could profit from having
such an enhanced knowledge base.
Abstract: This paper proposes a linear model for optimizing
domestic energy consumption in Romania. The particularity of the
model is that it is putting in competition both tangible technologies
and thermal insulation projects with different financing modes.
The model is optimizing the energy system by minimizing the
global discounted cost in household sector, by integrating residential
lighting, space heating, hot water, combined space heating – hot
water, as well as space cooling, in a monolithic model. Another
demand sector included is the passenger transport.
This paper focuses on space heating part, analyzing technical and
economic issues related to investment decisions to envelope and
insulate buildings, in order to minimize energy consumption.
Abstract: In this paper, an experiment was conducted to assess
the impact of online deliberation on citizens’ attitudes. Specifically,
this research compared pre and post deliberation opinions of
participants who deliberated online via an asynchronous platform
regarding the issue of political opinion polls. Results indicate that
online deliberation had a positive effect on citizens’ attitudes since it
was found that following deliberation participants changed their
views regarding public opinion polls. Specifically, online deliberation
improved discussants perceptions regarding the reliability of polls,
while suppressing their negative views about the misuse of polls by
media, polling organizations and politicians.
Abstract: We used live E. coli containing synthetic genetic
oscillators to study how the degree of synchrony between the genetic
circuits of sister cells changes with temperature. We found that both
the mean and the variability of the degree of synchrony between the
fluorescence signals from sister cells are affected by temperature.
Also, while most pairs of sister cells were found to be highly
synchronous in each condition, the number of asynchronous pairs
increased with increasing temperature, which was found to be due to
disruptions in the oscillations. Finally we provide evidence that these
disruptions tend to affect multiple generations as opposed to
individual cells. These findings provide insight in how to design
more robust synthetic circuits and in how cell division can affect their
dynamics.
Abstract: Most of the oil palm plantations have been threatened
by Basal Stem Rot (BSR) disease which causes serious economic
impact. This study was conducted to identify the healthy and BSRinfected
oil palm tree using thirteen color indices. Multispectral and
thermal camera was used to capture 216 images of the leaves taken
from frond number 1, 9 and 17. Indices of normalized difference
vegetation index (NDVI), red (R), green (G), blue (B), near infrared
(NIR), green – blue (GB), green/blue (G/B), green – red (GR),
green/red (G/R), hue (H), saturation (S), intensity (I) and thermal
index (T) were used. From this study, it can be concluded that G
index taken from frond number 9 is the best index to differentiate
between the healthy and BSR-infected oil palm trees. It not only gave
high value of correlation coefficient (R=-0.962), but also high value
of separation between healthy and BSR-infected oil palm tree.
Furthermore, power and S model developed using G index gave the
highest R2 value which is 0.985.
Abstract: Implementation of advanced technologies requires
sophisticated instruments that deal with the operation, control,
restoration and protection of rapidly growing power system network
under normal and abnormal conditions. Presently, the applications of
Phasor Measurement Unit (PMU) are widely found in real time
operation, monitoring, controlling and analysis of power system
network as it eliminates the various limitations of supervisory control
and data acquisition system (SCADA) conventionally used in power
system. The use of PMU data is very rapidly increasing its
importance for online and offline analysis. Wide area measurement
system (WAMS) is developed as new technology by use of multiple
PMUs in power system. The present paper proposes a model of
Matlab based PMU using Discrete Fourier Transform (DFT)
algorithm and evaluation of its operation under different
contingencies. In this paper, PMU based two bus system having
WAMS network is presented as a case study.
Abstract: Durability of Membrane Electrode Assembly for
Proton Exchange Membrane Fuel Cells was evaluated in both steady
state and accelerated decay modes. Steady state mode was carried out
at constant current of 800mA/cm2 for 2500 hours using air as cathode
feed and pure hydrogen as anode feed. The degradation of the cell
voltage was 0.015V after such 2500 hrs operation. The degradation
rate was therefore calculated to be 6uV/hr. Continuously Vigorous
fluctuation of the cell voltage, which was switched between OCV and
0.2V, was employed for the accelerated decay mode. No obvious
change in performance of the MEA was observed after 10000 cycles
of such operation.
Abstract: A novel method is presented for obtaining the stress
field induced by an edge dislocation in a multilayered composite. To
demonstrate the applications of the obtained solution, we consider the
problem of an interfacial crack in a periodically layered bimaterial
medium. The crack is modelled as a continuous distribution of edge
dislocations and the Distributed Dislocation Technique (DDT) is
utilized to obtain numerical results for the energy release rate (ERR).
The numerical implementation of the dislocation solution in
MATLAB is also provided.
Abstract: This paper presents development results of usage of
C-OTDR monitoring systems for rail traffic management. The COTDR
method is based on vibrosensitive properties of optical fibers.
Analysis of Rayleigh backscattering radiation parameters changes
which take place due to microscopic seismoacoustic impacts on the
optical fiber allows to determine seismoacoustic emission source
positions and to identify their types. This approach proved successful
for rail traffic management (moving block system, weigh- in-motion
system etc.).
Abstract: In recent years a new method of combination
treatment for cancer has been developed and studied that has led to
significant advancements in the field of cancer therapy. Hyperthermia
is a traditional therapy that, along with a creation of a medically
approved level of heat with the help of an alternating magnetic AC
current, results in the destruction of cancer cells by heat. This paper
gives details regarding the production of the spherical nanocomposite
PVA/γ-Fe2O3 in order to be used for medical purposes such as tumor
treatment by hyperthermia. To reach a suitable and evenly distributed
temperature, the nanocomposite with core-shell morphology and
spherical form within a 100 to 200 nanometer size was created using
phase separation emulsion, in which the magnetic nano-particles γ-
Fe2O3 with an average particle size of 20 nano-meters and with
different percentages of 0.2, 0.4, 0.5 and 0.6 were covered by
polyvinyl alcohol. The main concern in hyperthermia and heat
treatment is achieving desirable specific absorption rate (SAR) and
one of the most critical factors in SAR is particle size. In this project
all attempts has been done to reach minimal size and consequently
maximum SAR. The morphological analysis of the spherical
structure of the nanocomposite PVA/γ-Fe2O3 was achieved by SEM
analyses and the study of the chemical bonds created was made
possible by FTIR analysis. To investigate the manner of magnetic
nanocomposite particle size distribution a DLS experiment was
conducted. Moreover, to determine the magnetic behavior of the γ-
Fe2O3 particle and the nanocomposite PVA/γ-Fe2O3 in different
concentrations a VSM test was conducted. To sum up, creating
magnetic nanocomposites with a spherical morphology that would be
employed for drug loading opens doors to new approaches in
developing nanocomposites that provide efficient heat and a
controlled release of drug simultaneously inside the magnetic field,
which are among their positive characteristics that could significantly
improve the recovery process in patients.
Abstract: In this work, the Ictalurus punctatus species estimated
available physical habitat is compared with the estimated physical
habitat for the same but modified river reach, with the aim of creating
a linear park, along a length of 5 500 m.
To determine the effect of ecological park construction, on
physical habitat of the Lerma river stretch of study, first, the available
habitat for the Ictalurus punctatus species was estimated through the
simulation of the physical habitat, by using surveying, hydraulics,
and habitat information gotten at the river reach in its actual situation.
Second, it was estimated the available habitat for the above species,
upon the simulation of the physical habitat through the proposed
modification for the ecological park creation. Third, it is presented a
comparison between both scenarios in terms of available habitat
estimated for Ictalurus punctatus species, concluding that in cases of
adult and spawning life stages, changes in the channel to create an
ecological park would produce a considerable loss of potentially
usable habitat (PUH), while in the case of the juvenile life stage PUH
remains virtually unchanged, and in the case of life stage fry the PUH
would increase due to the presence of velocities and depths of lesser
magnitude, due to the presence of minor flow rates and lower volume
of the wet channel.
It is expected that habitat modification for linear park construction
may produce the lack of Ictalurus punktatus species conservation at
the river reach of the study.
Abstract: Using the quantum hydrodynamic (QHD) model the
nonlinear properties of ion-acoustic waves in are lativistically
degenerate quantum plasma is investigated by deriving a nonlinear
Spherical Kadomtsev–Petviashvili (SKP) equation using the
standard reductive perturbation method equation. It was found that
the electron degeneracy parameter significantly affects the linear
and nonlinear properties of ion-acoustic waves in quantum plasma.