Abstract: An early diagnosis of bone metastasis is very
important for making a right decision on a subsequent therapy. One
of the most important steps to be taken initially, for developing a new
radiopharmaceutical is the measurement of organ radiation exposure
dose. In this study, the dosimetric studies of a novel agent for
SPECT-imaging of the bone metastasis, 111In-(4-
{[(bis(phosphonomethyl))carbamoyl]methyl}7,10bis(carboxymethyl)
-1,4,7,10-tetraazacyclododec-1-yl) acetic acid (111In-BPAMD)
complex, have been carried out to estimate the dose in human organs
based on the data derived from mice. The radiolabeled complex was
prepared with high radiochemical purity in the optimal conditions.
Biodistribution studies of the complex was investigated in the male
Syrian mice at the selected times after injection (2, 4, 24 and 48 h).
The human absorbed dose estimation of the complex was made based
on data derived from the mice by the radiation absorbed dose
assessment resource (RADAR) method. 111In-BPAMD complex was prepared with high radiochemical
purity >95% (ITLC) and specific activities of 2.85 TBq/mmol. Total
body effective absorbed dose for 111In-BPAMD was 0.205
mSv/MBq. This value is comparable to the other 111In clinically used
complexes. The results show that the dose with respect to the critical
organs is satisfactory within the acceptable range for diagnostic
nuclear medicine procedures. Generally, 111In-BPAMD has
interesting characteristics and it can be considered as a viable agent
for SPECT-imaging of the bone metastasis in the near future.
Abstract: The current study focuses on the seismic design of
offshore pipelines against active faults. After an extensive literature
review of the provisions of the seismic norms worldwide and of the
available analytical methods, the study simulates numerically
(through finite-element modeling and strain-based criteria) the
distress of offshore pipelines subjected to PGDs induced by active
normal and reverse seismic faults at the seabed. Factors, such as the
geometrical properties of the fault, the mechanical properties of the
ruptured soil formations, and the pipeline characteristics, are
examined. After some interesting conclusions regarding the seismic
vulnerability of offshore pipelines, potential cost-effective mitigation
measures are proposed taking into account constructability issues.
Abstract: One of the challenges that higher education faces is to
find how to approach the sustainability in an inclusive way to the
student within all the different academic areas, how to move the
sustainable development from the abstract field to the operational
field. This research comes from the ecoliteracy and the pedagogical
praxis as tools for rebuilding the teaching processes inside of
universities. The purpose is to determine and describe which are the
factors involved in the process of learning particularly in the
Greenhouse-School Siembra UV. In the Greenhouse-School Siembra UV, of the University of
Veracruz, are cultivated vegetables, medicinal plants and small
cornfields under the usage of eco-technologies such as hydroponics,
Wickingbed and Hugelkultur, which main purpose is the saving of
space, labor and natural resources, as well as function as agricultural
production alternatives in the urban and periurban zones. The sample was formed with students from different academic
areas and who are actively involved in the greenhouse, as well as
institutes from the University of Veracruz and governmental and nongovernmental
departments. This project comes from a pedagogic praxis approach, from filling
the needs that the different professional profiles of the university
students have. All this with the purpose of generate a pragmatic
dialogue with the sustainability. It also comes from the necessity to
understand the factors that intervene in the students’ praxis. In this
manner is how the students are the fundamental unit in the sphere of
sustainability. As a result, it is observed that those University of Veracruz
students who are involved in the Greenhouse-school, Siembra UV,
have enriched in different levels the sense of urban and periurban
agriculture because of the diverse academic approaches they have
and the interaction between them. It is concluded that the ecotechnologies
act as fundamental tools for ecoliteracy in society,
where it is strengthen the nutritional and food security from a
sustainable development approach.
Abstract: At the present work, highly transparent strip type
quasi-solid state dye-sensitized solar cells (DSSCs) were fabricated
through inkjet printing using nanocomposite TiO2 inks as raw
materials and tested under outdoor illumination conditions. The cells,
which can be considered as the structural units of large area modules,
were fully characterized electrically and electrochemically and after
the evaluation of the received results a large area DSSC module was
manufactured. The module design was a sandwich Z-interconnection
where the working electrode is deposited on one conductive glass and
the counter electrode on a second glass. Silver current collective
fingers were printed on the conductive glasses to make the internal
electrical connections and the adjacent cells were connected in series
and finally insulated using a UV curing resin to protect them from the
corrosive (I-/I3-) redox couple of the electrolyte. Finally, outdoor tests
were carried out to the fabricated dye-sensitized solar module and its
performance data were collected and assessed.
Abstract: The traditional rhythms of the West African country
of Guinea have played a centuries-long role in defining the different
people groups that make up the country. Throughout their history,
before and since colonization by the French, the different ethnicities
have used their traditional music as a distinct part of their historical
identities. That is starting to change. Guinea is an impoverished
nation created in the early twentieth-century with little regard for the
history and cultures of the people who were included. The traditional
rhythms of the different people groups and their heritages have
remained. Fifteen individual traditional Guinean rhythms were
chosen to represent popular rhythms from the four geographical
regions of Guinea. Each rhythm was traced back to its native village
and video recorded on-site by as many different local performing
groups as could be located. The cyclical patterns rhythms were
transcribed via a circular, spatial design and then copied into a box
notation system where sounds happening at the same time could be
studied. These rhythms were analyzed for their consistency-overperformance
in a Fundamental Rhythm Pattern analysis so rhythms
could be compared for how they are changing through different
performances. The analysis showed that the traditional rhythm
performances of the Middle and Forest Guinea regions were the most
cohesive and showed the least evidence of change between
performances. The role of music in each of these regions is both
limited and focused. The Coastal and High Guinea regions have
much in common historically through their ethnic history and
modern-day trade connections, but the rhythm performances seem to
be less consistent and demonstrate more changes in how they are
performed today. In each of these regions the role and usage of music
is much freer and wide-spread. In spite of advances being made as a
country, different ethnic groups still frequently only respond and
participate (dance and sing) to the music of their native ethnicity.
There is some evidence that this self-imposed musical barrier is
beginning to change and evolve, partially through the development of
better roads, more access to electricity and technology, the nationwide
Ebola health crisis, and a growing self-identification as a
unified nation.
Abstract: Abstract—[Tris (1,10-phenanthroline) lanthanum(III)]
trithiocyanate is a new compound that has shown high ability for
stopping the synthesis of DNA and also acting as a photosensitizer.
Nowadays, the radiation dose assessment resource (RADAR) method
is known as the most common method for absorbed dose calculation.
177Lu was produced by (n, gamma) reaction in a research reactor.
177Lu-PL3 was prepared in the optimized condition. The
radiochemical yield was checked by ITLC method. The
biodistribution of the complex was investigated by intravenously
injection to wild-type rats via their tail veins. In this study, the
absorbed dose of 177Lu-PL3 to human organs was estimated by
RADAR method. 177Lu was prepared with a specific activity of 2.6-3
GBq.mg-1 and radionuclide purity of 99.98 %. Final preparation of
the radiolabelled complex showed high radiochemical purity of >
99%. The results show that liver and spleen have received the highest
absorbed dose of 1.051 and 0.441 mSv/MBq, respectively. The
absorbed dose values for these two dose-limiting tissues suggest
more biological studies special in tumor-bearing animals.
Abstract: The measurement of organ radiation exposure dose is
one of the most important steps to be taken initially, for developing a
new radiopharmaceutical. In this study, the dosimetric studies of a
novel agent for SPECT-imaging of the bone metastasis, 111In-
1,4,7,10-tetraazacyclododecane-1,4,7,10 tetraethylene phosphonic
acid (111In-DOTMP) complex, have been carried out to estimate the
dose in human organs based on the data derived from rats. The
radiolabeled complex was prepared with high radiochemical purity in
the optimal conditions. Biodistribution studies of the complex was
investigated in the male Syrian rats at selected times after injection
(2, 4, 24 and 48 h). The human absorbed dose estimation of the
complex was made based on data derived from the rats by the
radiation absorbed dose assessment resource (RADAR) method.
111In-DOTMP complex was prepared with high radiochemical purity
of >99% (ITLC). Total body effective absorbed dose for 111In-
DOTMP was 0.061 mSv/MBq. This value is comparable to the other
111In clinically used complexes. The results show that the dose with
respect to the critical organs is satisfactory within the acceptable
range for diagnostic nuclear medicine procedures. Generally, 111In-
DOTMP has interesting characteristics and can be considered as a
viable agent for SPECT-imaging of the bone metastasis in the near
future.
Abstract: The noise is one of the negative elements which
affects the human health. This article presents the measurement of
emitted noise by road vehicle and its parts during the operation.
Measurement was done in the interior of common passenger cars
with a digital sound meter. The results compare the noise value in
different cars with different body shape, which influences the driver’s
health. Transport has considerable ecological effects; many of them
are detrimental to environmental sustainability. Roads and traffic
exert a variety of direct and mostly detrimental effects on nature.
Abstract: This paper evaluates the accrual based scheduling for
cloud in single and multi-resource system. Numerous organizations
benefit from Cloud computing by hosting their applications. The
cloud model provides needed access to computing with potentially
unlimited resources. Scheduling is tasks and resources mapping to a
certain optimal goal principle. Scheduling, schedules tasks to virtual
machines in accordance with adaptable time, in sequence under
transaction logic constraints. A good scheduling algorithm improves
CPU use, turnaround time, and throughput. In this paper, three realtime
cloud services scheduling algorithm for single resources and
multiple resources are investigated. Experimental results show
Resource matching algorithm performance to be superior for both
single and multi-resource scheduling when compared to benefit first
scheduling, Migration, Checkpoint algorithms.
Abstract: This study aims at improving the urban hydrological
cycle of the Orléans agglomeration (France) and understanding the
relationship between physical and chemical parameters of urban
surface runoff and the hydrological conditions. In particular water
quality parameters such as pH, conductivity, total dissolved solids,
major dissolved cations and anions, and chemical and biological
oxygen demands were monitored for three types of urban water
discharges (wastewater treatment plant output (WWTP), storm
overflow and stormwater outfall) under two hydrologic scenarios (dry
and wet weather). The first results were obtained over a period of five
months. Each investigated (Ormes, l’Egoutier and La Corne) outfall
represents an urban runoff source that receives water from runoff
roads, gutters, the irrigation of gardens and other sources of flow over
the Earth’s surface that drains in its catchments and carries it to the
Loire River. In wet weather conditions there is rain water runoff and
an additional input from the roof gutters that have entered the
stormwater system during rainfall. For the comparison the results La
Chilesse is a storm overflow that was selected in our study as a
potential source of waste water which is located before the (WWTP). The comparison of the physical-chemical parameters (total
dissolved solids, turbidity, pH, conductivity, dissolved organic
carbon (DOC), concentration of major cations and anions) together
with the chemical oxygen demand (COD) and biological oxygen
demand (BOD) helped to characterize sources of runoff waters in the
different watersheds. It also helped to highlight the infiltration of
wastewater in some stormwater systems that reject directly in the
Loire River. The values of the conductivity measured in the outflow
of Ormes were always higher than those measured in the other two
outlets. The results showed a temporal variation for the Ormes outfall
of conductivity from 1465 μS cm-1 in the dry weather flow to 650 μS
cm-1 in the wet weather flow and also a spatial variation in the wet
weather flow from 650 μS cm-1 in the Ormes outfall to 281 μS cm-1
in L’Egouttier outfall. The ultimate BOD (BOD28) showed a
significant decrease in La Corne outfall from 181 mg L-1 in the wet
weather flow to 95 mg L-1 in the dry weather flow because of the
nutrient load that was transported by the runoff.
Abstract: A problem of complex mineral resources development is urgent and priority, it is aimed at realization of the processes of their ecologically safe development, one of its components is revealing the influence of the forms of element compounds in raw materials and in the processing products. In view of depletion of the precious metal reserves at the traditional deposits in the XXI century the large-size open cast deposits, localized in black shale strata begin to play the leading role. Carbonaceous (black) shales carry a heightened metallogenic potential. Black shales with high content of carbon are widely distributed within the scope of Bureinsky massif. According to academician Hanchuk`s data black shales of Sutirskaya series contain generally PGEs native form. The presence of high absorptive towards carbonaceous matter gold and PGEs compounds in crude ore results in decrease of valuable components extraction because of their sorption into dissipated carbonaceous matter.
Abstract: Processing of high-silicon bauxite on the base of the
traditional clinkering method is related to high power consumption
and capital investments, which makes production of alumina from
those ores non-competitive in terms of basic economic showings. For
these reasons, development of technological solutions enabling to
process bauxites with various chemical and mineralogical structures
efficiently with low level of thermal power consumption is important.
Flow sheet of the studies on washability of ores from the Timanskoe
and the Severo-Onezhskoe deposits is on the base of the flotation
method.
Abstract: An industrial system for the production of white
liquor of a paper industry, Klabin Paraná Papéis, formed by ten
reactors was modeled, simulated, and analyzed. The developed model
considered possible water losses by evaporation and reaction, in
addition to variations in volumetric flow of lime mud across the
reactors due to composition variations. The model predictions agreed
well with the process measurements at the plant and the results
showed that the slaking reaction is nearly complete at the third
causticizing reactor, while causticizing ends by the seventh reactor.
Water loss due to slaking reaction and evaporation occurs more
pronouncedly in the slaking reaction than in the final causticizing
reactors; nevertheless, the lime mud flow remains nearly constant
across the reactors.
Abstract: The hydrodynamic and thermal behaviors of fluid
flow in wavy microchannel are investigated numerically. Effects of
Reynolds number on the hydrodynamics and thermal behaviors are
investigated. Three cases of Reynolds number (580, 1244, and 1910)
are adopted in this study. It is found that the separation zone begin
appears when Reynolds number is greater than 1910 at the endsection
of the wave. Also it is found that dimensionless maximum
velocity at the mid-section of the wave decreases and becomes as a
turbulent behavior as Reynolds numbers increases. The maximum
temperature at the center line at the mid-section of the wave increases
as Reynolds number increases until it reaches the turbulent behavior
when Reynolds number is equal or greater than 1244, while this
behavior will be achieved at very high velocities at the end section of
the wave.
Abstract: This research was conducted in an automotive company in Indonesia to overcome the problem of high logistics cost. The problem causes high of additional truck delivery. From the breakdown of the problem, chosen one route, which has the highest gap value, namely for RE-04. Research methodology will be started from calculating the ideal condition, making simulation, calculating the ideal logistic cost, and proposing an improvement. From the calculation of the ideal condition, box arrangement was done on the truck has efficiency with three trucks delivery per day. Route simulation making uses Tecnomatix Plant Simulation software as a visualization for the company about how the system is occurred on route RE-04 in ideal condition. The last step is proposing improvements on the area of route RE-04. The route arrangement is done by Saving Method and sequence of each supplier with the Nearest Neighbor. The results of the proposed improvements are three new route groups, where was expected to decrease logistics cost and increase the average of the truck efficiency per day.
Abstract: In this numerical work, mixed convection and entropy
generation of Cu–water nanofluid in a lid-driven square cavity have
been investigated numerically using the Lattice Boltzmann Method.
Horizontal walls of the cavity are adiabatic and vertical walls have
constant temperature but different values. The top wall has been
considered as moving from left to right at a constant speed, U0. The
effects of different parameters such as nanoparticle volume
concentration (0–0.05), Rayleigh number (104–106) and Reynolds
numbers (1, 10 and 100) on the entropy generation, flow and
temperature fields are studied. The results have shown that addition
of nanoparticles to the base fluid affects the entropy generation, flow
pattern and thermal behavior especially at higher Rayleigh and low
Reynolds numbers. For pure fluid as well as nanofluid, the increase
of Reynolds number increases the average Nusselt number and the
total entropy generation, linearly. The maximum entropy generation
occurs in nanofluid at low Rayleigh number and at high Reynolds
number. The minimum entropy generation occurs in pure fluid at low
Rayleigh and Reynolds numbers. Also at higher Reynolds number,
the effect of Cu nanoparticles on enhancement of heat transfer was
decreased because the effect of lid-driven cavity was increased. The
present results are validated by favorable comparisons with
previously published results. The results of the problem are presented
in graphical and tabular forms and discussed.
Abstract: Chatter vibrations and process instabilities are the
most important factors limiting the productivity of the milling
process. Chatter can leads to damage of the tool, the part or the
machine tool. Therefore, the estimation and prediction of the process
stability is very important. The process stability depends on the
spindle speed, the depth of cut and the width of cut. In milling, the
process conditions are defined in the NC-program. While the spindle
speed is directly coded in the NC-program, the depth and width of cut
are unknown. This paper presents a new simulation based approach
for the prediction of the depth and width of cut of a milling process.
The prediction is based on a material removal simulation with an
analytically represented tool shape and a multi-dexel approach for the
workpiece. The new calculation method allows the direct estimation
of the depth and width of cut, which are the influencing parameters of
the process stability, instead of the removed volume as existing
approaches do. The knowledge can be used to predict the stability of
new, unknown parts. Moreover with an additional vibration sensor,
the stability lobe diagram of a milling process can be estimated and
improved based on the estimated depth and width of cut.
Abstract: The ventilated façade has great advantages when
compared to traditional façades as it reduces the air conditioning
thermal loads due to the stack effect induced by solar radiation in the
air chamber. Optimizing energy consumption by using a ventilated
façade can be used not only in newly built buildings but also it can be
implemented in existing buildings, opening the field of
implementation to energy building retrofitting works. In this sense, the following three prototypes of façade where
designed, built and further analyzed in this research: non-ventilated
façade (NVF); slightly ventilated façade (SLVF) and strongly
ventilated façade (STVF). The construction characteristics of the
three facades are based on the Spanish regulation of building
construction “Technical Building Code”. The façades have been
monitored by type-k thermocouples in a representative day of the
summer season in Madrid (Spain). Moreover, an analysis of variance
(ANOVA) with repeated measures, studying the thermal lag in the
ventilated and no-ventilated façades has been designed. Results show that STVF façade presents higher levels of thermal
inertia as the thermal lag reduces up to 17% (daily mean) compared
to the non-ventilated façade. In addition, the statistical analysis
proves that an increase of the ventilation holes size in STVF façades
can improve the thermal lag significantly (p >0.05) when compared
to the SLVF façade.
Abstract: The practical efficient approach is suggested to estimate the high-speed objects instant bounds in C-OTDR monitoring systems. In case of super-dynamic objects (trains, cars) is difficult to obtain the adequate estimate of the instantaneous object localization because of estimation lag. In other words, reliable estimation coordinates of monitored object requires taking some time for data observation collection by means of C-OTDR system, and only if the required sample volume will be collected the final decision could be issued. But it is contrary to requirements of many real applications. For example, in rail traffic management systems we need to get data of the dynamic objects localization in real time. The way to solve this problem is to use the set of statistical independent parameters of C-OTDR signals for obtaining the most reliable solution in real time. The parameters of this type we can call as «signaling parameters» (SP). There are several the SP’s which carry information about dynamic objects instant localization for each of COTDR channels. The problem is that some of these parameters are very sensitive to dynamics of seismoacoustic emission sources, but are non-stable. On the other hand, in case the SP is very stable it becomes insensitive as rule. This report contains describing of the method for SP’s co-processing which is designed to get the most effective dynamic objects localization estimates in the C-OTDR monitoring system framework.
Abstract: This paper presents the results of a Finite Element
based vibration analysis of a solar powered Unmanned Aerial
Vehicle (UAV). The purpose of this paper was to quantify the free
vibration, forced vibration response due to differing point inputs in
order to predict the relative response magnitudes and frequencies at
various wing locations of vibration induced power generators
(magnet in coil) excited by gust and/or control surface pulse-decays
used to help power the flight of the electric UAV. A Fluid Structure
Interaction (FSI) study was performed in order to ascertain pertinent
design stresses and deflections as well as aerodynamic parameters of
the UAV airfoil. The 10 ft span airfoil is modeled using Mylar as the
primary material. Results show that the free mode in bending is 4.8
Hz while the first forced bending mode is on range of 16.2 to 16.7 Hz
depending on the location of excitation. The free torsional bending
mode is 28.3 Hz, and the first forced torsional mode is range of 26.4
to 27.8 Hz, depending on the location of excitation. The FSI results
predict the coefficients of aerodynamic drag and lift of 0.0052 and
0.077, respectively, which matches hand-calculations used to validate
the Finite Element based results. FSI based maximum von Mises
stresses and deflections were found to be 0.282 MPa and 3.4 mm,
respectively. Dynamic pressures on the airfoil range from 1.04 to
1.23 kPa corresponding to velocity magnitudes in range of 22 to 66
m/s.