Abstract: The advantage of solving the complex nonlinear
problems by utilizing fuzzy logic methodologies is that the
experience or expert-s knowledge described as a fuzzy rule base can
be directly embedded into the systems for dealing with the problems.
The current limitation of appropriate and automated designing of
fuzzy controllers are focused in this paper. The structure discovery
and parameter adjustment of the Branched T-S fuzzy model is
addressed by a hybrid technique of type constrained sparse tree
algorithms. The simulation result for different system model is
evaluated and the identification error is observed to be minimum.
Abstract: Delay-Tolerant Networks (DTNs) are sparse, wireless
networks where disconnections are common due to host mobility and
low node density. The Message Ferrying (MF) scheme is a mobilityassisted
paradigm to improve connectivity in DTN-like networks. A
ferry or message ferry is a special node in the network which has
a per-determined route in the deployed area and relays messages
between mobile hosts (MHs) which are intermittently connected.
Increased contact opportunities among mobile hosts and the ferry
improve the performance of the network, both in terms of message
delivery ratio and average end-end delay. However, due to the inherent
mobility of mobile hosts and pre-determined periodicity of the
message ferry, mobile hosts may often -miss- contact opportunities
with a ferry. In this paper, we propose the combination of stationary
ferry access points (FAPs) with MF routing to increase contact
opportunities between mobile hosts and the MF and consequently
improve the performance of the DTN. We also propose several
placement models for deploying FAPs on MF routes. We evaluate the
performance of the FAP placement models through comprehensive
simulation. Our findings show that FAPs do improve the performance
of MF-assisted DTNs and symmetric placement of FAPs outperforms
other placement strategies.
Abstract: Titanium alloys like the modern alloy Ti 6Al 2Sn 4Zr 6Mo (Ti-6246) combine excellent specific mechanical properties and corrosion resistance. On the other hand,due to their material characteristics, machining of these alloys is difficult to perform. The aim of the current study is the analyses of wear mechanisms of coated cemented carbide tools applied in orthogonal cutting experiments of Ti-6246 alloy. Round bars were machined with standard coated tools in dry conditions on a CNC latheusing a wide range of cutting speeds and cutting depths. Tool wear mechanisms were afterwards investigated by means of stereo microscopy, optical microscopy, confocal microscopy and scanning electron microscopy. Wear mechanisms included fracture of the tool tip (total failure) and abrasion. Specific wear features like crater wear, micro cracks and built-up edgeformation appeared depending of the mechanical and thermal conditions generated in the workpiece surface by the cutting action.
Abstract: Exposure to radon occurs when breathing airborne
radon while using water: showering, washing dishes, cooking, and
drinking water that contain radon. The results of radon activity
measurements in water from public drinking fountain in city of Novi
Sad, Serbia is presented in this paper. Radon level in some samples
exceeded EPA (Environmental Protection Agency) recommendation
for maximum contaminant level (MCL) for radon in drinking water
of 11.1 Bq/l.
Abstract: In an effort to understand the preliminary effects of aerodynamic stress on alveolar epithelial cells, we developed a multifluidic cell culture platform capable of supporting alveolar cultures at an air-liquid interface under constant air flow and exposure to varying pressure stimuli on the apical side while providing nourishment on the basolateral plane. Our current study involved utilizing the platform to study the effect of basement membrane coating and addition of dexamethasone on cellular response to pressure in A549 and H441 alveolar epithelial cells.
Abstract: Titanium nitride (TiN) has been synthesized using the
sheet plasma negative ion source (SPNIS). The parameters used for
its effective synthesis has been determined from previous
experiments and studies. In this study, further enhancement of the
deposition rate of TiN synthesis and advancement of the SPNIS
operation is presented. This is primarily achieved by the addition of
Sm-Co permanent magnets and a modification of the configuration in
the TiN deposition process. The magnetic enhancement is aimed at
optimizing the sputtering rate and the sputtering yield of the process.
The Sm-Co permanent magnets are placed below the Ti target for
better sputtering by argon. The Ti target is biased from –250V to –
350V and is sputtered by Ar plasma produced at discharge current of
2.5–4A and discharge potential of 60–90V. Steel substrates of
dimensions 20x20x0.5mm3 were prepared with N2:Ar volumetric
ratios of 1:3, 1:5 and 1:10. Ocular inspection of samples exhibit
bright gold color associated with TiN. XRD characterization
confirmed the effective TiN synthesis as all samples exhibit the (200)
and (311) peaks of TiN and the non-stoichiometric Ti2N (220) facet.
Cross-sectional SEM results showed increase in the TiN deposition
rate of up to 0.35μm/min. This doubles what was previously obtained
[1]. Scanning electron micrograph results give a comparative
morphological picture of the samples. Vickers hardness results gave
the largest hardness value of 21.094GPa.
Abstract: In this paper is shown that the probability-statistic methods application, especially at the early stage of the aviation gas turbine engine (GTE) technical condition diagnosing, when the flight information has property of the fuzzy, limitation and uncertainty is unfounded. Hence is considered the efficiency of application of new technology Soft Computing at these diagnosing stages with the using of the Fuzzy Logic and Neural Networks methods. Training with high accuracy of fuzzy multiple linear and non-linear models (fuzzy regression equations) which received on the statistical fuzzy data basis is made. Thus for GTE technical condition more adequate model making are analysed dynamics of skewness and kurtosis coefficients' changes. Researches of skewness and kurtosis coefficients values- changes show that, distributions of GTE work parameters have fuzzy character. Hence consideration of fuzzy skewness and kurtosis coefficients is expedient. Investigation of the basic characteristics changes- dynamics of GTE work parameters allows to draw conclusion on necessity of the Fuzzy Statistical Analysis at preliminary identification of the engines' technical condition. Researches of correlation coefficients values- changes shows also on their fuzzy character. Therefore for models choice the application of the Fuzzy Correlation Analysis results is offered. For checking of models adequacy is considered the Fuzzy Multiple Correlation Coefficient of Fuzzy Multiple Regression. At the information sufficiency is offered to use recurrent algorithm of aviation GTE technical condition identification (Hard Computing technology is used) on measurements of input and output parameters of the multiple linear and non-linear generalised models at presence of noise measured (the new recursive Least Squares Method (LSM)). The developed GTE condition monitoring system provides stage-bystage estimation of engine technical conditions. As application of the given technique the estimation of the new operating aviation engine temperature condition was made.
Abstract: This article is an extension and a practical application
approach of Wheeler-s NEBIC theory (Net Enabled Business
Innovation Cycle). NEBIC theory is a new approach in IS research
and can be used for dynamic environment related to new technology.
Firms can follow the market changes rapidly with support of the IT
resources. Flexible firms adapt their market strategies, and respond
more quickly to customers changing behaviors. When every leading
firm in an industry has access to the same IT resources, the way that
these IT resources are managed will determine the competitive
advantages or disadvantages of firm. From Dynamic Capabilities
Perspective and from newly introduced NEBIC theory by Wheeler,
we know that only IT resources cannot deliver customer value but
good configuration of those resources can guarantee customer value
by choosing the right emerging technology, grasping the economic
opportunities through business innovation and growth. We found
evidences in literature that SOA (Service Oriented Architecture) is a
promising emerging technology which can deliver the desired
economic opportunity through modularity, flexibility and loosecoupling.
SOA can also help firms to connect in network which can
open a new window of opportunity to collaborate in innovation and
right kind of outsourcing
Abstract: Product Data Management (PDM) systems for Computer
Aided Design (CAD) file management are widely established
in design processes. This management system is indispensable for
design collaboration or when design task distribution is present. It is
thus surprising that engineering design curricula has not paid much
attention in the education of PDM systems. This is also the case
for eduction of ecodesign and environmental evaluation of products.
With the rise of sustainability as a strategic aspect in companies,
environmental concerns are becoming a key issue in design. This
paper discusses the establishment of a PDM platform to be used
among technical and vocational schools in Austria. The PDM system
facilitates design collaboration among these schools. Further, it will
be discussed how the PDM system has been prepared in order to
facilitate environmental evaluation of parts, components and subassemblies
of a product. By integrating a Business Intelligence
solution, environmental Life Cycle Assessment and communication
of results is enabled.
Abstract: This paper will focus on modeling, analysis and simulation of a 42V/14V dc/dc converter based architecture. This architecture is considered to be technically a viable solution for automotive dual-voltage power system for passenger car in the near further. An interleaved dc/dc converter system is chosen for the automotive converter topology due to its advantages regarding filter reduction, dynamic response, and power management. Presented herein, is a model based on one kilowatt interleaved six-phase buck converter designed to operate in a Discontinuous Conduction Mode (DCM). The control strategy of the converter is based on a voltagemode- controlled Pulse Width Modulation (PWM) with a Proportional-Integral-Derivative (PID). The effectiveness of the interleaved step-down converter is verified through simulation results using control-oriented simulator, MatLab/Simulink.
Abstract: The need for micromechanical inertial sensors is increasing
in future electronic stability control (ESC) and other positioning,
navigation and guidance systems. Due to the rising density of
sensors in automotive and consumer devices the goal is not only to get
high performance, robustness and smaller package sizes, but also to
optimize the energy management of the overall sensor system. This
paper presents an evaluation concept for a surface micromachined
yaw rate sensor. Within this evaluation concept an energy-efficient
operation of the drive mode of the yaw rate sensor is enabled. The
presented system concept can be realized within a power management
subsystem.
Abstract: Absorption and fluorescence spectra of quinine
sulphate (QSD) have been recorded at room temperature in wide
range of solvents of different polarities. The ground-state dipole
moment of QSD was obtained from quantum mechanical calculations
and the excited state dipole moment of QSD was estimated from
Bakhshiev-s and Kawski-Chamma-Viallet-s equations by means of
solvatochromic shift method. Higher value of dipole moment is
observed for excited state as compared to the corresponding ground
state value and this is attributed to the more polar excited state of
QSD.
Abstract: Active Power Filters (APFs) are today the most
widely used systems to eliminate harmonics compensate power
factor and correct unbalanced problems in industrial power plants.
We propose to improve the performances of conventional APFs by
using artificial neural networks (ANNs) for harmonics estimation.
This new method combines both the strategies for extracting the
three-phase reference currents for active power filters and DC link
voltage control method. The ANNs learning capabilities to
adaptively choose the power system parameters for both to compute
the reference currents and to recharge the capacitor value requested
by VDC voltage in order to ensure suitable transit of powers to
supply the inverter. To investigate the performance of this
identification method, the study has been accomplished using
simulation with the MATLAB Simulink Power System Toolbox. The
simulation study results of the new (SAPF) identification technique
compared to other similar methods are found quite satisfactory by
assuring good filtering characteristics and high system stability.
Abstract: In this contribution a newly developed e-learning environment is presented, which incorporates Intelligent Agents and Computational Intelligence Techniques. The new e-learning environment is constituted by three parts, the E-learning platform Front-End, the Student Questioner Reasoning and the Student Model Agent. These parts are distributed geographically in dispersed computer servers, with main focus on the design and development of these subsystems through the use of new and emerging technologies. These parts are interconnected in an interoperable way, using web services for the integration of the subsystems, in order to enhance the user modelling procedure and achieve the goals of the learning process.
Abstract: With high speed vessels getting ever more sophisti-cated, travelling at higher and higher speeds and operating in With high speed vessels getting ever more sophisticated,
travelling at higher and higher speeds and operating in areas of
high maritime traffic density, training becomes of the highest priority
to ensure that safety levels are maintained, and risks are adequately
mitigated. Training onboard the actual craft on the actual route still
remains the most effective way for crews to gain experience. However,
operational experience and incidents during the last 10 years
demonstrate the need for supplementary training whether in the area
of simulation or man to man, man/ machine interaction. Training and
familiarisation of the crew is the most important aspect in preventing
incidents. The use of simulator, computer and web based training
systems in conjunction with onboard training focusing on critical
situations will improve the man machine interaction and thereby
reduce the risk of accidents. Today, both ship simulator and bridge
teamwork courses are now becoming the norm in order to improve
further emergency response and crisis management skills. One of the
main causes of accidents is the human factor. An efficient way to
reduce human errors is to provide high-quality training to the personnel
and to select the navigators carefully.areas of high maritime traffic density, training becomes of the highest priority to ensure that safety levels are maintained, and risks are adequately mitigated. Training onboard the actual craft on the actual route still remains the most effective way for crews to gain experience. How-ever, operational experience and incidents during the last 10 years demonstrate the need for supplementary training whether in the area of simulation or man to man, man/ machine interaction. Training and familiarisation of the crew is the most important aspect in preventing incidents. The use of simulator, computer and web based training systems in conjunction with onboard training focusing on critical situations will improve the man machine interaction and thereby reduce the risk of accidents. Today, both ship simulator and bridge teamwork courses are now becoming the norm in order to improve further emergency response and crisis management skills. One of the main causes of accidents is the human factor. An efficient way to reduce human errors is to provide high-quality training to the person-nel and to select the navigators carefully. KeywordsCBT - WBT systems, Human factors.
Abstract: In this paper, quantitative evaluation of ultrasonic Cscan
images through estimation of their Fractal Dimension (FD) is
discussed. Necessary algorithm for evaluation of FD of any 2-D
digitized image is implemented by developing a computer code. For
the evaluation purpose several C-scan images of the Kevlar
composite impacted by high speed bullet and glass fibre composite
having flaw in the form of inclusion is used. This analysis
automatically differentiates a C-scan image showing distinct damage
zone, from an image that contains no such damage.
Abstract: Sweet potato products are necessary for the provision
of essential nutrients in every household, regardless of their poverty
status. Their consumption appears to be highly influenced by socioeconomic
factors, such as malnutrition, food insecurity and
unemployment. Therefore, market availability is crucial for these
cultivars to resolve some of the socio-economic factors. The aim of
the study was to investigate market availability of sweet potato
cultivars in the North West Province. In this study, both qualitative
and quantitative research methodologies were used. Qualitative
methodology was used to explain the quantitative outcomes of the
variables. On the other hand, quantitative results were used to test the
hypothesis. The study used SPSS software to analyse the data. Crosstabulation
and Chi-square statistics were used to obtain the
descriptive and inferential analyses, respectively. The study found
that the Blesbok cultivar is dominating the markets of the North West
Province, with the Monate cultivar dominating in the Bojanala
Platinum (75%) and Dr Ruth Segomotsi Mompati (25%) districts. It
is also found that a unit increase in the supply of sweet potato
cultivars in both local and district municipal markets is accompanied
by a reduced demand of 28% and 33% at district and local markets,
respectively. All these results were found to be significant at p
Abstract: Considering the merits and limitations of energy dissipation system, seismic isolation system and suspension system, a new earthquake resistant system is proposed and is demonstrated numerically through a frame-core structure. Base isolators and story isolators are installed in the proposed system. The former “isolates" the frame from the foundation and the latter “separates" the frame from the center core. Equations of motion are formulated to study the response of the proposed structural system to strong earthquake motion. As compared with the fixed-base building system, the proposed structural system shows substantial reduction on structural response.
Abstract: This paper presents the study of hardness profile of spur gear heated by induction heating process in function of the machine parameters, such as the power (kW), the heating time (s) and the generator frequency (kHz). The global work is realized by 3D finite-element simulation applied to the process by coupling and resolving the electromagnetic field and the heat transfer problems, and it was performed in three distinguished steps. First, a Comsol 3D model was built using an adequate formulation and taking into account the material properties and the machine parameters. Second, the convergence study was conducted to optimize the mesh. Then, the surface temperatures and the case depths were deeply analyzed in function of the initial current density and the heating time in medium frequency (MF) and high frequency (HF) heating modes and the edge effect were studied. Finally, the simulations results are validated using experimental tests.
Abstract: The UK Government has emphasized the role of Local Authorities as a key player in its flagship residential energy efficiency strategies, by identifying and targeting areas for energy efficiency improvements. Residential energy consumption in England is characterized by significant geographical variation in energy demand, which makes centralized targeting of areas for energy efficiency intervention difficult. This paper draws on research which aims to understand how demographic, social, economic, urban form and climatic factors influence the geographical variations in English residential gas consumption. The paper reports the findings of a multiple regression model that shows how 64% of the geographical variation in residential gas consumption is accounted for by variations in these factors. Results from this study, after further refinement and validation, can be used by Local Authorities to identify areas within their boundaries that have higher than expected gas consumption, these may be prime targets for energy efficiency initiatives.