Abstract: Nonlinear evolution of broadband ultrasonic pulses
passed through the rock specimens is studied using the apparatus
“GEOSCAN-02M”. Ultrasonic pulses are excited by the pulses of Qswitched
Nd:YAG laser with the time duration of 10 ns and with the
energy of 260 mJ. This energy can be reduced to 20 mJ by some light
filters. The laser beam radius did not exceed 5 mm. As a result of the
absorption of the laser pulse in the special material – the optoacoustic
generator–the pulses of longitudinal ultrasonic waves are excited with
the time duration of 100 ns and with the maximum pressure
amplitude of 10 MPa. The immersion technique is used to measure
the parameters of these ultrasonic pulses passed through a specimen,
the immersion liquid is distilled water. The reference pulse passed
through the cell with water has the compression and the rarefaction
phases. The amplitude of the rarefaction phase is five times lower
than that of the compression phase. The spectral range of the
reference pulse reaches 10 MHz. The cubic-shaped specimens of the
Karelian gabbro are studied with the rib length 3 cm. The ultimate
strength of the specimens by the uniaxial compression is (300±10)
MPa. As the reference pulse passes through the area of the specimen
without cracks the compression phase decreases and the rarefaction
one increases due to diffraction and scattering of ultrasound, so the
ratio of these phases becomes 2.3:1. After preloading some horizontal
cracks appear in the specimens. Their location is found by one-sided
scanning of the specimen using the backward mode detection of the
ultrasonic pulses reflected from the structure defects. Using the
computer processing of these signals the images are obtained of the
cross-sections of the specimens with cracks. By the increase of the
reference pulse amplitude from 0.1 MPa to 5 MPa the nonlinear
transformation of the ultrasonic pulse passed through the specimen
with horizontal cracks results in the decrease by 2.5 times of the
amplitude of the rarefaction phase and in the increase of its duration
by 2.1 times. By the increase of the reference pulse amplitude from 5
MPa to 10 MPa the time splitting of the phases is observed for the
bipolar pulse passed through the specimen. The compression and
rarefaction phases propagate with different velocities. These features
of the powerful broadband ultrasonic pulses passed through the rock
specimens can be described by the hysteresis model of Preisach-
Mayergoyz and can be used for the location of cracks in the optically
opaque materials.
Abstract: The hydrodynamic and thermal behaviors of fluid
flow in wavy microchannel are investigated numerically. Effects of
Reynolds number on the hydrodynamics and thermal behaviors are
investigated. Three cases of Reynolds number (580, 1244, and 1910)
are adopted in this study. It is found that the separation zone begin
appears when Reynolds number is greater than 1910 at the endsection
of the wave. Also it is found that dimensionless maximum
velocity at the mid-section of the wave decreases and becomes as a
turbulent behavior as Reynolds numbers increases. The maximum
temperature at the center line at the mid-section of the wave increases
as Reynolds number increases until it reaches the turbulent behavior
when Reynolds number is equal or greater than 1244, while this
behavior will be achieved at very high velocities at the end section of
the wave.
Abstract: Si-Ge solid solutions (bulk poly- and mono-crystalline
samples, thin films) are characterized by high perspectives for
application in semiconductor devices, in particular, optoelectronics
and microelectronics. From this point of view, complex studying of
structural state of the defects and structural-sensitive physical
properties of Si-Ge solid solutions depending on the contents of Si
and Ge components is very important. Present work deals with the
investigations of microstructure, microhardness, internal friction and
shear modulus of Si1-xGex(x≤0,02) bulk monocrystals conducted at
room temperature. Si-Ge bulk crystals were obtained by Czochralski
method in [111] crystallographic direction. Investigated
monocrystalline Si-Ge samples are characterized by p-type
conductivity and carriers’ concentration 5.1014-1.1015cm-3.
Microhardness was studied on Dynamic Ultra Micro hardness Tester
DUH-201S with Berkovich indenter. Investigate samples are characterized with 0,5x0,5x(10-15)mm3
sizes, oriented along [111] direction at torsion oscillations ≈1Hz,
multistage changing of internal friction and shear modulus has been
revealed in an interval of strain amplitude of 10-5-5.10-3. Critical
values of strain amplitude have been determined at which hysteretic
changes of inelastic characteristics and microplasticity are observed. The critical strain amplitude and elasticity limit values are also
determined. Dynamic mechanical characteristics decreasing trend is
shown with increasing Ge content in Si-Ge solid solutions. Observed
changes are discussed from the point of view of interaction of various
dislocations with point defects and their complexes in a real structure
of Si-Ge solid solutions.
Abstract: Ocean current is always available around the
surrounding of SHELL Sabah Water Platform and data are collected
every 10 minutes, 24 hours a day, for a period of 365 days. Due to
low current speed, conventional hydrokinetic power generation is not
feasible, thus leading to the study of low current enabled vortex
induced vibration power generation application. In this case, the
design of a vortex induced vibration application is studied to obtain
an optimum design for the VIV oscillator. Power output is then
determined to study the feasibility of the VIV application in low
current condition.
Abstract: The authors conducted a study for the sample size of
75 HR managers from an Indian IT company through systematic
sampling method. This study identifies that the female employees are
facing lesser conflict than the male employees against their managers
within the organization. There is a positive correlation between
gender and conflict management with the superior towards the work.
There is a significant variance between age and response towards
appraisal system, succession planning and employee engagement.
The education qualification plays a major role in determining the
compensation factor for the employees working in the organization.
The study determines the impact of demographic profile on strategic
HRM practices and its challenges faced by HR managers in IT firm,
India.
Abstract: Target of this study was the analysis of the impact of
crude glycerol on canine spermatozoa motility, morphology,
viability, and membrane integrity. Experiments were realized in vitro.
In the study, semen from 5 large dog breeds was used. They were
typical representatives of large breeds, coming from healthy rearing,
regularly vaccinated and integrated to the further breeding. Semen
collections were realized at the owners of animals and in the
veterinary clinic. Subsequently the experiments were realized at the
Department of Animal Physiology of the SUA in Nitra. The
spermatozoa motility was evaluated using CASA analyzer
(SpermVisionTM, Minitub, Germany) at the temperature 5 and 37°C
for 5 hours. In the study, 13 motility parameters were evaluated.
Generally, crude glycerol has generally negative effect on
spermatozoa motility. Morphological analysis was realized using
Hancock staining and the preparations were evaluated at
magnification 1000x using classification tables of morphologically
changed spermatozoa. Data clearly detected the highest number of
morphologically changed spermatozoa in the experimental groups
(know twisted tails, tail torso and tail coiling). For acrosome
alterations swelled acrosomes, removed acrosomes and acrosomes
with undulated membrane were detected. In this study also the effect
of crude glycerol on spermatozoa membrane integrity were analyzed.
The highest crude glycerol concentration significantly affects
spermatozoa integrity. Results of this study show that crude glycerol
has effect of spermatozoa motility, viability, and membrane integrity.
Detected changes are related to crude glycerol concentration,
temperature, as well as time of incubation.
Abstract: Digital reference service is when a traditional library
reference service is provided electronically. In most cases users do
not get full satisfaction from using digital reference service due to
variety of reasons. This paper discusses the formal specification of
web services applications for digital reference services (WSDRS).
WSDRS is an informal model that claims to reduce the problems of
digital reference services in libraries. It uses web services technology
to provide efficient digital way of satisfying users’ need in the
reference section of libraries. Informal model is in natural language
which is inconsistent and ambiguous that may cause difficulties to the
developers of the system. In order to solve this problem we decided
to convert the informal specifications into formal specifications. This
is supposed to reduce the overall development time and cost. We use
Z language to develop the formal model and verify it with Z/EVES
theorem prover tool.
Abstract: In this work, we attempt to associate firm
characteristics with innovative activity. We collect microdata from
listed firms of selected Eurozone Country-members, after the
beginning of 2007 financial crisis. The following literature, several
indicators of growth and performance were selected and tested for
their ability to interpret innovative activity. The main scope is to
examine the possible differences in performance and growth between
innovative and non-innovative firms, during a severe recession.
Additionally to that, a special focus will be held on whether
macroeconomic performance and national innovation system,
determines the extent of innovators' performance. Preliminary
findings, through correlation matrices and non-parametric tests,
strongly indicate the positive relation between innovative activity and
most of the measures used (profitability, size, employment),
confirming that even during a recessionary period, innovative firms
not only survive but also seem to succeed better economic results in
almost all indexes relative to non-innovative. However, even though
innovators seem to perform better in all economies examined, the
extent of that performance seems to be strongly affected by the
supportive mechanisms (financial and structural) that their country
provides. Thus, it is clear, that the technologically intensive 'gap'
between European South and North, during the economic crisis,
became chaotic, due to the harsh austerity measures and reduced
budgets in those countries, even in sectors with high potentials in
economic activity and employment, impairing the effects of crisis and
enhancing the vicious circle of recession.
Abstract: Thermal enhancement of a single mini channel in
Proton Exchange Membrane Fuel Cell (PEMFC) cooling plate is
numerically investigated. In this study, low concentration of Al2O3 in
Water - Ethylene Glycol mixtures is used as coolant in single channel
of carbon graphite plate to mimic the mini channels in PEMFC
cooling plate. A steady and incompressible flow with constant heat
flux is assumed in the channel of 1mm x 5mm x 100mm. Nano
particle of Al2O3 used ranges from 0.1, 0.3 and 0.5 vol %
concentration and then dispersed in 60:40 (water: Ethylene Glycol)
mixture. The effect of different flow rates to fluid flow and heat
transfer enhancement in Re number range of 20 to 140 was observed.
The result showed that heat transfer coefficient was improved by
18.11%, 9.86% and 5.37% for 0.5, 0.3 and 0.1 vol. % Al2O3 in 60:40
(water: EG) as compared to base fluid of 60:40 (water: EG). It is also
showed that the higher vol. % concentration of Al2O3 performed
better in term of thermal enhancement but at the expense of higher
pumping power required due to increase in pressure drop
experienced. Maximum additional pumping power of 0.0012W was
required for 0.5 vol % Al2O3 in 60:40 (water: EG) at Re number 140.
Abstract: There are real needs to integrate types of Open
Educational Resources (OER) with an intelligent system to extract
information and knowledge in the semantic searching level. The
needs came because most of current learning standard adopted web
based learning and the e-learning systems do not always serve all
educational goals. Semantic Web systems provide educators,
students, and researchers with intelligent queries based on a semantic
knowledge management learning system. An ontology-based learning
system is an advanced system, where ontology plays the core of the
semantic web in a smart learning environment. The objective of this
paper is to discuss the potentials of ontologies and mapping different
kinds of ontologies; heterogeneous or homogenous to manage and
control different types of Open Educational Resources. The important
contribution of this research is that it uses logical rules and
conceptual relations to map between ontologies of different
educational resources. We expect from this methodology to establish
an intelligent educational system supporting student tutoring, self and
lifelong learning system.
Abstract: Operation enhancement in an air cooler depends on
rate of heat transfer, and pressure drop. In this paper for a given heat
duty, study of the effects of FPI (Fin Per Inch) and fin type (circular
and hexagonal fins) on heat transfer, and pressure drop in an air
cooler in Iran, Arvand petrochemical. A program in EES
(Engineering Equations Solver) software moreover, Aspen B-JAC
and HTFS+ softwares are used for this purpose to solve governing
equations. At first the simulated results obtained from this program is
compared to the experimental data for two cases of FPI. The effects
of FPI from 3 to 15 over heat transfer (Q) to pressure drop ratio
(Q/Δp ratio). This ratio is one of the main parameters in design, and
simulation heat exchangers. The results show that heat transfer (Q)
and pressure drop increase with increasing FPI steadily, and the Q/Δp
ratio increases to FPI=12 and then decreased gradually to FPI=15,
and Q/Δp ratio is maximum at FPI=12. The FPI value selection
between 8 and 12 obtained as a result to optimum heat transfer to
pressure drop ratio. Also by contrast, between circular and hexagonal
fins results, the Q/Δp ratio of hexagonal fins more than Q/Δp ratio of
circular fins for FPI between 8 and 12 (optimum FPI)
Abstract: The latest years the number of immigrants at Greece
has increased dramatically. Their impact on the National Health
System (NHS) has not been yet thoroughly investigated. This paper
analyses the cost of immigrants to the NHS hospitals of the region of
Eastern Macedonia and Thrace. The data are collected from 2005 to
2011 from five different hospitals and are analysed using linear
mixed effects models in order to investigate the effects of nationality
and year on the cost of hospitalization and treatment. The results
show that generally the Greek nationality patients have a higher mean
cost of hospitalization compared to the immigrants and that there is
an increasing trend for the cost except for the year 2010.
Abstract: In view of the requirements of the current industrial
processes, the instrumentation plays a critical role. In this context,
this work aims to raise some the operating characteristics of the level
and flow transmitters, in addition to observing their similarities and
possible limitations configurations.
Abstract: Three purified diets were formulated using fish meal,
soya bean, wheat flour, palm oil, minerals and maltose. The
carbohydrate in the diets was increased from 5 to 15% by changing
the cellulose content to study the effect of dietary carbohydrate level
on the growth parameters of Nile tilapia Oreochromis niloticus. The
protein and the lipid contents were kept constant in all the diets. The
results showed that, weight gain, protein efficiency ratio, net protein
utilisation and hepatosomatic index of fish fed the diet containing
15% cellulose were the lowest among all groups. Addition, the fish
fed the diet containing 5% cellulose had the best specific growth rate,
and food conversion ratio. While, there was no effect of the dietary
cellulose levels on condition factor and survival rate. These results
indicate that Nile tilapia fingerlings are able to utilize dietary
cellulose does not exceed 10% in their feed for optimum growth.
Abstract: Chatter vibrations and process instabilities are the
most important factors limiting the productivity of the milling
process. Chatter can leads to damage of the tool, the part or the
machine tool. Therefore, the estimation and prediction of the process
stability is very important. The process stability depends on the
spindle speed, the depth of cut and the width of cut. In milling, the
process conditions are defined in the NC-program. While the spindle
speed is directly coded in the NC-program, the depth and width of cut
are unknown. This paper presents a new simulation based approach
for the prediction of the depth and width of cut of a milling process.
The prediction is based on a material removal simulation with an
analytically represented tool shape and a multi-dexel approach for the
workpiece. The new calculation method allows the direct estimation
of the depth and width of cut, which are the influencing parameters of
the process stability, instead of the removed volume as existing
approaches do. The knowledge can be used to predict the stability of
new, unknown parts. Moreover with an additional vibration sensor,
the stability lobe diagram of a milling process can be estimated and
improved based on the estimated depth and width of cut.
Abstract: The ventilated façade has great advantages when
compared to traditional façades as it reduces the air conditioning
thermal loads due to the stack effect induced by solar radiation in the
air chamber. Optimizing energy consumption by using a ventilated
façade can be used not only in newly built buildings but also it can be
implemented in existing buildings, opening the field of
implementation to energy building retrofitting works. In this sense, the following three prototypes of façade where
designed, built and further analyzed in this research: non-ventilated
façade (NVF); slightly ventilated façade (SLVF) and strongly
ventilated façade (STVF). The construction characteristics of the
three facades are based on the Spanish regulation of building
construction “Technical Building Code”. The façades have been
monitored by type-k thermocouples in a representative day of the
summer season in Madrid (Spain). Moreover, an analysis of variance
(ANOVA) with repeated measures, studying the thermal lag in the
ventilated and no-ventilated façades has been designed. Results show that STVF façade presents higher levels of thermal
inertia as the thermal lag reduces up to 17% (daily mean) compared
to the non-ventilated façade. In addition, the statistical analysis
proves that an increase of the ventilation holes size in STVF façades
can improve the thermal lag significantly (p >0.05) when compared
to the SLVF façade.
Abstract: In this paper, we present a quantum statistical
mechanical formulation from our recently analytical expressions for
partial-wave transition matrix of a three-particle system. We report
the quantum reactive cross sections for three-body scattering
processes 1+(2,3)→1+(2,3) as well as recombination
1+(2,3)→1+(3,1) between one atom and a weakly-bound dimer. The
analytical expressions of three-particle transition matrices and their
corresponding cross-sections were obtained from the threedimensional
Faddeev equations subjected to the rank-two non-local
separable potentials of the generalized Yamaguchi form. The
equilibrium quantum statistical mechanical properties such partition
function and equation of state as well as non-equilibrium quantum
statistical properties such as transport cross-sections and their
corresponding transport collision integrals were formulated
analytically. This leads to obtain the transport properties, such as
viscosity and diffusion coefficient of a moderate dense gas.
Abstract: The conventional ceramic route was utilized to
prepare a hard magnetic powder (M-type strontium ferrite,
SrFe12O19). The stoichiometric mixture of iron oxide and strontium
carbonate were calcined at 1000oC and then fired at various
temperatures. The influence of various reaction parameters such as
mixing ratio, calcination temperature, firing temperature and firing
time on the magnetic behaviors of the synthesized magnetic powder
were investigated. The magnetic properties including Coercivity
(Hc), Magnetic saturation (Ms), and Magnetic remnance (Mr) were
measured by vibrating sample magnetometer. Morphologically the
produced magnetic powder has a dense hexagonal grain shape
structure.
Abstract: A teeming set of doctors that graduated from various
universities within and outside Nigeria with the hope of practicing in
the country, has their hope shattered because of poor financing, lack
of medical equipments and a very weak healthcare systems. Such
hydra headed challenges, allows room for quackery which
increasingly contributes to the cause of mortality in Nigeria. With a
view of reversing the challenges of healthcare delivery and financing
in Nigeria, African Health Market for Equity (AHME), a project
funded by the Bill and Melinda Gates foundation [With contribution
from Department For International Development (DFID)] and
currently implemented in three African Countries (Nigeria, Kenya
and Ghana) over a Five (5) year period supports the healthcare sector
via Medical credit fund (MCF). The study examines the impact of
credit policy and medical credit funding on Nigerian health market.
Ordinary least square analysis, correlation and granger causality tests
were employed to measure the extent to which the Nigerian
healthcare market has been influenced. Medical credit fund
significantly and positively influenced average monthly turnover of
private healthcare providers and Commercial bank’s lending rate had
a weak relationship with access to credit/approved loans (13.46%).
The programme has so far made 13.91% progress, which is very
poor, considering the minimum targeted private health care providers
(437.6) and expected number of loan approvals (180.4) for the two
years. Medical credit policy in Nigeria should be revised to include
private healthcare providers in rural area for more positive impact
and increased returns. Good brand advert and sensitization of the
programme to stakeholders and health pressure group, and an
extension of the programme beyond five years is necessary to better
address the issues raised in the study.
Abstract: This study was undertaken at four different sites
(north polluted, south polluted, south healthy and north healthy) in
Tehran, in order to examine whether there was a relationship between
publicly available air quality data and the public’s perception of air
quality and to suggest some guidelines for reducing air pollution. A
total of 200 people were accidentally filled out the research
questionnaires at mentioned sites and air quality data were obtained
simultaneously from the Air Quality Control Department. Data was
analyzed in Excel and SPSS software’s. Clean air and job security
were of great importance to people comparing to other pleasant
aspect of life. Also air pollution and serious diseases were the most
important of people concerns. Street monitors and news paper
services on air quality were little used by the public as a means of
obtaining information on air pollution. Using public transportation
and avoiding inevitable journeys are the most important ways for
reducing air pollution. The results reveal that the public’s perception
of air quality is not a reliable indicator of the actual levels of air
pollution.