Abstract: A numerical study has been carried out to investigate
the heat transfer by natural convection of nanofluid taking Cu as
nanoparticles and the water as based fluid in a three dimensional
annulus enclosure filled with porous media (silica sand) between two
horizontal concentric cylinders with 12 annular fins of 2.4mm
thickness attached to the inner cylinder under steady state conditions.
The governing equations which used are continuity, momentum and
energy equations under an assumptions used Darcy law and
Boussinesq-s approximation which are transformed to dimensionless
equations. The finite difference approach is used to obtain all the
computational results using the MATLAB-7. The parameters affected
on the system are modified Rayleigh number (10 ≤Ra*≤ 1000), fin
length Hf (3, 7 and 11mm), radius ratio Rr (0.293, 0.365 and 0.435)
and the volume fraction(0 ≤ ¤ò ≤ 0 .35). It was found that the
average Nusselt number depends on (Ra*, Hf, Rr and φ). The results
show that, increasing of fin length decreases the heat transfer rate and
for low values of Ra*, decreasing Rr cause to decrease Nu while for
Ra*
greater than 100, decreasing Rr cause to increase Nu and adding
Cu nanoparticles with 0.35 volume fraction cause 27.9%
enhancement in heat transfer. A correlation for Nu in terms of Ra*,
Hf and φ, has been developed for inner hot cylinder.
Abstract: Highly ordered arrays of TiO2 nanotubes (TiNTs) were grown vertically on Ti foil by electrochemical anodization. We controlled the lengths of these TiNTs from 2.4 to 26.8 ¶üÇóμm while varying the water contents (1, 3, and 6 wt%) of the electrolyte in ethylene glycol in the presence of 0.5 wt% NH4F with anodization for various applied voltages (20–80 V), periods (10–240 min) and temperatures (10–30 oC). For vertically aligned TiNT arrays, not only the increase in their tube lengths, but also their geometric (wall thickness and surface roughness) and crystalline structure lead to a significant influence on photocatalytic activity. The length optimization for methylene blue (MB) photodegradation was 18 μm. Further extending the TiNT length yielded lower photocatalytic activity presumably related to the limited MB diffusion and light-penetration depth into the TiNT arrays. The results indicated that a maximum MB photodegradation rate was obtained for the discrete anatase TiO2 nanotubes with thick and rough walls.
Abstract: Dielectric sheet perturbation to the dominant TE111
mode resonant frequency of a circular cavity is studied and presented
in this paper. The dielectric sheet, placed at the middle of the airfilled
cavity, introduces discontinuities and disturbs the configuration
of electromagnetic fields in the cavity. For fixed dimensions of cavity
and fixed thickness of the loading dielectric, the dominant resonant
frequency varies quite linearly with the permittivity of the dielectric.
This quasi-linear relationship is plotted using Maple software and
verified using 3D electromagnetic simulations. Two probes are used
in the simulation for wave excitation into and from the cavity. The
best length of probe is found to be 3 mm, giving the closest resonant
frequency to the one calculated using Maple. A total of fourteen
different dielectrics of permittivity ranging from 1 to 12.9 are tested
one by one in the simulation. The works show very close agreement
between the results from Maple and the simulation. A constant
difference of 0.04 GHz is found between the resonant frequencies
collected during simulation and the ones from Maple. The success of
this project may lead to the possibility of using the middle loaded
cavity at TE111 mode as a microwave non-destructive testing of solid
materials.
Abstract: The knowledge of the nature of loading is very
important in order to hold account on the total behavior such as
vibration, shock, fatigue, etc. Fatigue present 90% of failure when
loadings fatigues are very complex. In this paper a study of double
through crack at hole for plate subjected to fatigue loading is
presented. Various modes loading are studied where the applied load
is the same one. The fatigue life is given where the effect of stress
ratio is highlighted. This work is conducted on aluminum alloy 2024
T351 used for much aerospace and aeronautics applications. The
fatigue crack growth behavior with constant amplitude is studied
using the AFGROW code when Forman model is applied. The
fatigue crack growth rate and fatigue life for different loading modes
are compared with variation of others geometrical parameter such as
thickness and dimensions of notch hole.
Abstract: The limit load carrying capacity of functionally
graded materials (FGM) circular plates subjected to an arbitrary
rotationally symmetric loading has been computed. It is provided that
the plate material behaves rigid perfectly plastic and obeys either the
Square or the Tresca yield criterion. To this end the upper and lower
bound principles of limit analysis are employed to determine the
exact value for the limiting load. The correctness of the result are
verified and finally limiting loads for two examples namely; through
radius and through thickness FGM circular plates with simply
supported edges are calculated, respectively and moreover, the values
of critical loading factor are determined.
Abstract: In a state-of-the-art industrial production line of
photovoltaic products the handling and automation processes are of
particular importance and implication. While processing a fully
functional crystalline solar cell an as-cut photovoltaic wafer is subject
to numerous repeated handling steps. With respect to stronger
requirements in productivity and decreasing rejections due to defects
the mechanical stress on the thin wafers has to be reduced to a
minimum as the fragility increases by decreasing wafer thicknesses.
In relation to the increasing wafer fragility, researches at the
Fraunhofer Institutes IPA and CSP showed a negative correlation
between multiple handling processes and the wafer integrity. Recent
work therefore focused on the analysis and optimization of the dry
wafer stack separation process with compressed air. The achievement
of a wafer sensitive process capability and a high production
throughput rate is the basic motivation in this research.
Abstract: Bicycle usage for exercise, recreation, and commuting
to work in Australia shows that pedal cycling is the fourth most
popular activity with 10.6% increase in participants between 2001
and 2007. As with other means of transport, accident and injury
becomes common although mandatory bicycle helmet wearing has
been introduced. The research aims to develop a face surrogate made
of sandwich of rigid foam and rubber sheets to represent human
facial bone under blunt impact. The facial surrogate will serve as an
important test device for further development of facial-impact
protection for cyclist. A test procedure was developed to simulate the
energy of impact and record data to evaluate the effect of impact on
facial bones. Drop tests were performed to establish a suitable
combination of materials. It was found that the sandwich structure of
rigid extruded-polystyrene foam (density of 40 kg/m3 with a pattern
of 6-mm-holes), Neoprene rubber sponge, and Abrasaflex rubber
backing, had impact characteristics comparable to that of human
facial bone. In particular, the foam thickness of 30 mm and 25 mm
was found suitable to represent human zygoma (cheekbone) and
maxilla (upper-jaw bone), respectively.
Abstract: Heating is inevitable in any bearing operation. This
leads to not only the thinning of the lubricant but also could lead to a
thermal deformation of the bearing. The present work is an attempt to
analyze the influence of thermal deformation on the thermohydrodynamic
lubrication of infinitely long tilted pad slider rough
bearings. As a consequence of heating the slider is deformed and is
assumed to take a parabolic shape. Also the asperities expand leading
to smaller effective film thickness. Two different types of surface
roughness are considered: longitudinal roughness and transverse
roughness. Christensen-s stochastic approach is used to derive the
Reynolds-type equations. Density and viscosity are considered to be
temperature dependent. The modified Reynolds equation, momentum
equation, continuity equation and energy equation are decoupled and
solved using finite difference method to yield various bearing
characteristics. From the numerical simulations it is observed that the
performance of the bearing is significantly affected by the thermal
distortion of the slider and asperities and even the parallel sliders
seem to carry some load.
Abstract: For the communication between human and computer
in an interactive computing environment, the gesture recognition is
studied vigorously. Therefore, a lot of studies have proposed efficient
methods about the recognition algorithm using 2D camera captured
images. However, there is a limitation to these methods, such as the
extracted features cannot fully represent the object in real world.
Although many studies used 3D features instead of 2D features for
more accurate gesture recognition, the problem, such as the processing
time to generate 3D objects, is still unsolved in related researches.
Therefore we propose a method to extract the 3D features combined
with the 3D object reconstruction. This method uses the modified
GPU-based visual hull generation algorithm which disables unnecessary
processes, such as the texture calculation to generate three kinds
of 3D projection maps as the 3D feature: a nearest boundary, a farthest
boundary, and a thickness of the object projected on the base-plane. In
the section of experimental results, we present results of proposed
method on eight human postures: T shape, both hands up, right hand
up, left hand up, hands front, stand, sit and bend, and compare the
computational time of the proposed method with that of the previous
methods.
Abstract: This paper presents the experimental results on effect of applied voltage stress frequency to the occurrence of electrical treeing in 22 kV cross linked polyethylene (XLPE) insulated cable.Hallow disk of XLPE insulating material with thickness 5 mm taken from unused high voltage cable was used as the specimen in this study. Stainless steel needle was inserted gradually into the specimen to give a tip to earth plane electrode separation of 2.50.2 mm at elevated temperature 105-110°C. The specimen was then annealed for 5 minute to minimize any mechanical stress build up around the needle-plane region before it was cooled down to room temperature. Each specimen were subjected to the same applied voltage stress level at 8 kV AC rms, with various frequency, 50, 100, 500, 1000 and 2000 Hz. Initiation time, propagation speed and pattern of electrical treeing were examined in order to study the effect of applied voltage stress frequency. By the experimental results, initial time of visible treeing decreases with increasing in applied voltage frequency. Also, obviously, propagation speed of electrical treeing increases with increasing in applied voltage frequency.Furthermore, two types of electrical treeing, bush-like and branch-like treeing were observed.The experimental results confirmed the effect of voltage stress frequency as well.
Abstract: Yam starch obtained from the water yam (munlued)
by the wet milling process was studied for some physicochemical
properties. Yam starch film was prepared by casting using glycerol as
a plasticizer. The effect of different glycerol (1.30, 1.65 and
2.00g/100g of filmogenic solution) and starch concentrations (3.30,
3.65 and 4.00g /100g of filmogenic solution) were evaluated on some
characteristics of the film. The temperature for obtaining the
gelatinized starch solution was 70-80°C and then dried at 45°C for 4
hours. The resulting starch from munlued granular morphology was
triangular and the average size of the granule was 26.68 μm. The
amylose content by colorimetric method was 26 % and the gelatinize
temperature was 70-80°C. The appearance of the film was smooth,
transparent, and glossy with average moisture content of 25.96% and
thickness of 0.01mm. Puncture deformation and flexibility increased
with glycerol content. The starch and glycerol concentration were a
significant factor of the yam starch film characteristics. Yam starch
film can be described as a biofilm providing many applications and
developments with the advantage of biodegradability.
Abstract: Physical and mechanical properties of Russian olive
fruits were measured at moisture content of 14.43% w.b. The results
revealed that the mean length, width and thickness of Russian olive
fruits were 20.72, 15.73 and 14.69mm, respectively. Mean mass and
volume of Russian olive fruits were measured as 1.45 g and 2.55 cm3,
respectively. The sphericity, aspect ratio and surface area were
calculated as 0.81, 0.72 and 8.96 cm2, respectively, while arithmetic
mean diameter, geometric mean diameter and equivalent diameter of
Russian olive fruits were 17.05, 16.83 and 16.84 mm, respectively.
Whole fruit density, bulk density and porosity of jujube fruits were
measured and found to be 1.01 g/cm3, 0.29 g/cm3 and 69.5%,
respectively. The values of static coefficient of friction on three
surfaces of glass, galvanized iron and plywood were 0.35, 0.36 and
0.43, respectively. The skin color (L*, a*, b*) varied from 9.92 to
16.08; 2.04 to 3.91 and 1.12 to 3.83, respectively. The values of
rupture force, deformation, energy absorbed and hardness were found
to be between 12.14-16.85 N, 2.16-4.25 mm, 3.42-6.99 N mm and
17.1-23.85 N/mm.
Abstract: The aim of this paper is to determine the stress levels
at the end of a long slender shaft such as a drilling assembly used in
the oil or gas industry using a mathematical model in real-time. The
torsional deflection experienced by this type of drilling shaft (about 4
KM length and 20 cm diameter hollow shaft with a thickness of 1
cm) can only be determined using a distributed modeling technique.
The main objective of this project is to calculate angular velocity and
torque at the end of the shaft by TLM method and also analyzing of
the behavior of the system by transient response. The obtained result
is compared with lumped modeling technique the importance of these
results will be evident only after the mentioned comparison. Two
systems have different transient responses and in this project because
of the length of the shaft transient response is very important.
Abstract: The governing two-dimensional equations of a heterogeneous material composed of a fluid (allowed to flow in the absence of acoustic excitations) and a crystalline piezoelectric cubic solid stacked one-dimensionally (along the z direction) are derived and special emphasis is given to the discussion of acoustic group velocity for the structure as a function of the wavenumber component perpendicular to the stacking direction (being the x axis). Variations in physical parameters with y are neglected assuming infinite material homogeneity along the y direction and the flow velocity is assumed to be directed along the x direction. In the first part of the paper, the governing set of differential equations are derived as well as the imposed boundary conditions. Solutions are provided using Hamilton-s equations for the wavenumber vs. frequency as a function of the number and thickness of solid layers and fluid layers in cases with and without flow (also the case of a position-dependent flow in the fluid layer is considered). In the first part of the paper, emphasis is given to the small-frequency case. Boundary conditions at the bottom and top parts of the full structure are left unspecified in the general solution but examples are provided for the case where these are subject to rigid-wall conditions (Neumann boundary conditions in the acoustic pressure). In the second part of the paper, emphasis is given to the general case of larger frequencies and wavenumber-frequency bandstructure formation. A wavenumber condition for an arbitrary set of consecutive solid and fluid layers, involving four propagating waves in each solid region, is obtained again using the monodromy matrix method. Case examples are finally discussed.
Abstract: This study aimed to evaluate regional soil Borkhar of
the metals Lead has been made. In this field study fires visits to the
regions. The limit of this study located in the East refineries,
petrochemical and power plant to 20 km was selected. The 41 soil
samples from depths of 0 to 10 cm in area and were randomized. Soil
samples were transported to the laboratory and by air was dry and
passed through 2-mil thickness sieve. In the laboratory of physical
and chemical characteristics and concentrations of total absorption
was measured. The results showed that the amount of lead in soil in
many parts of the range higher than the standard limit. Survey maps
show that the lead spatial distribution of the region does not special
pattern.
Abstract: Some physical properties of musk lime (Citrus
microcarpa) were determined in this study. The average moisture
content (wet basis) of the fruit was found to be 85.10 (±0.72) %. The
mean of length, width and thickness of the fruit was 26.36 (±0.97),
26.40 (±1.04) and 25.26 (±0.94) mm respectively. The average value
for geometric mean diameter, sphericity, aspect ratio, mass, surface
area, volume, true density, bulk density and porosity was 26.00
(±0.82) mm, 98.67 (±2.04) %, 100.23 (±3.28) %, 10.007 (±0.878) g,
2125.07 (±133.93) mm2, 8800.00 (±731.82) mm3, 1002.87 (±39.16)
kgm-3, 501.70 (±22.58) kgm-3 and 49.89 (±3.15) % respectively.
The coefficient of static friction on four types of structural surface
was found to be varying from 0.238 (±0.025) for glass to 0.247
(±0.024) for steel surface.
Abstract: In this work, thermoelastic damping effect on the hemi- spherical shells is investigated. The material is selected silicon, and heat conduction equation for thermal flow is solved to obtain the temperature profile in which bending approximation with inextensional assumption of the model. Using the temperature profile, eigen-value analysis is performed to get the natural frequencies of hemispherical shells. Effects of mode numbers, radii and radial thicknesses of the model on the natural frequencies are analyzed in detail. Furthermore, the quality factor (Q-factor) is defined, and discussed for the ring and hemispherical shell.
Abstract: In the present study, changes of morphology and
mechanical characteristics in the lumbar vertebrae of the
ovariectomised (OVX) rat were investigated. In previous researches,
there were many studies about morphology like volume fraction and
trabecular thickness based on Micro - Computed Tomography (Micro
- CT). However, detecting and tracking long-term changes in the
trabecular bone of the lumbar vertebrae for the OVX rat were few. For
this study, one female Sprague-Dawley rat was used: an OVX rat. The
4th Lumbar of the OVX rat was subjected to in-vivo micro-CT.
Detecting and tracking long-term changes could be investigated in the
trabecular bone of the lumbar vertebrae for an OVX rat using in-vivo
micro-CT. An OVX rat was scanned at week 0 (just before surgery), at
week 4, at week 8, week 16, week 22 and week 56 after surgery. Finite
element (FE) analysis was used to investigate mechanical
characteristics of the lumbar vertebrae for an OVX rat. When the OVX
rat (at week 56) was compared with the OVX rat (at week 0), volume
fraction was decreased by 80% and effective modulus was decreased
by 75%.
Abstract: Industrial radiography is a famous technique for the identification and evaluation of discontinuities, or defects, such as cracks, porosity and foreign inclusions found in welded joints. Although this technique has been well developed, improving both the inspection process and operating time, it does suffer from several drawbacks. The poor quality of radiographic images is due to the physical nature of radiography as well as small size of the defects and their poor orientation relatively to the size and thickness of the evaluated parts. Digital image processing techniques allow the interpretation of the image to be automated, avoiding the presence of human operators making the inspection system more reliable, reproducible and faster. This paper describes our attempt to develop and implement digital image processing algorithms for the purpose of automatic defect detection in radiographic images. Because of the complex nature of the considered images, and in order that the detected defect region represents the most accurately possible the real defect, the choice of global and local preprocessing and segmentation methods must be appropriated.
Abstract: The stability of Newtonian and Non-Newtonian extending films under local or global heating or cooling conditions are considered. The thickness-averaged mass, momentum and energy equations with convective and radiative heat transfer are derived, both for Newtonian and non-Newtonian fluids (Maxwell, PTT and Giesekus models considered). The stability of the system is explored using either eigenvalue analysis or transient simulations. The results showed that the influence of heating and cooling on stability strongly depends on the magnitude of the Peclet number. Examples of stabilization or destabilization of heating or cooling are shown for Pe