Abstract: Forward Osmosis (FO) polyamide thin-film composite
membranes have been prepared by interfacial polymerization using
commercial UF polyethersulfoneas membrane support. Different
interfacial polymerization times (10s, 30s and 60s) in the organic
solution containing trimesoyl chloride (TMC) at constant m-phenylenediamine
(MPD) concentration (2% w/v) were studied. The
synthesized polyamide membranes then tested for treatment of
natural organic matter (NOM) and compared to commercial Cellulose
TriAcetate (CTA) membrane. It was found that membrane prepared
with higher reaction time (30s and 60s) exhibited better membrane
performance (flux and humic acid removal) over commercial CTA
membrane.
Abstract: It is well known that in recent years magnetic
materials have received increased attention due to their properties.
For this reason a significant number of patents that were published
during the last decade are oriented towards synthesis and study of
such materials. The aim of this work is to create and study ferrite
nanocrystalline materials with spinel structure, using sol-gel
technology with participation of auto-combustion. This method is
perspective in that it is a cheap and low-temperature technique that
allows for the fine control on the product’s chemical composition.
Abstract: Specific leaf area (SLA; cm2leaf g-1leaf) the ratio of leaf
area to leaf dry mass is a key ecophysiological parameter influencing
leaf physiology, photosynthesis, and whole plant carbon gain and
also can be used as a rapid and diagnostic tool. In this study, two
species of soluble inorganic selenium forms, selenite (Se^IV) and
selenate (Se^VI) at different concentrations were investigated on maize
plants that were growing in nutrient solutions during 2 weeks and at
the end of the experiment, amounts of SLA for first and second
leaves of maize were measured. In accordance with the results we
observed that our regarded Se concentrations in both forms of Se^IV
and Se^VI were not effective on maize plants’ SLA significantly
although high level of 3 mg.kg-1 Se^IV had negative affect on growth
of the samples that had been treated by it but about Se^VI samples we
did not observe this state and our different considered Se^VI
concentrations were not toxic for maize plants.
Abstract: Silica was extracted from agriculture waste rice husk
ash (RHA) and was used as the silica source for synthesis of
RMCM-48 and RSBA-16. An alkali fusion process was utilized to
separate silicate supernatant and the sediment effectively. The
CTAB/Si and F127/Si molar ratio was employed to control the
structure properties of the obtained RMCM-48 and RSBA-16
materials. The N2 adsorption-desorption results showed the
micro-mesoporous RSBA-16 possessed high specific surface areas
(662-1001 m2/g). All the obtained RSBA-16 materials were applied as
the adsorbents for acetone adsorption. And the breakthrough tests
clearly revealed that the RSBA-16(0.004) materials could achieve the
highest acetone adsorption capacity of 181 mg/g under 1000 ppmv
acetone vapor concentration at 25oC, which was also superior to
ZSM-5 (71mg/g) and MCM-41 (157mg/g) under same test conditions.
This can help to reduce the solid waste and the high adsorption
performance of the obtained materials could consider as potential
adsorbents for acetone adsorption.
Abstract: In the present work, the dielectric properties of
Epoxy/MWCNT-muscovite HYBRID and MIXED composites based
on a ratio 30:70 were studied. The multi-wall carbon nanotubes
(MWCNT) were prepared using two methods: (a) MWCNTmuscovite
hybrids were synthesised by chemical vapour deposition
(CVD) and (b) physically mixing muscovite with MWCNT. The
effects of different preparation of the composites and filler loading
were evaluated. It was revealed that the dielectric constants of
HYBRID epoxy composites are slightly higher than MIXED epoxy
composites. It was also indicated that the dielectric constant increased
by increasing the MWCNT filler loading.
Abstract: In review the generalized data about biosynthetic routs
formation anthraquinone molecules in natural cells. The basic
possibilities of various ways of biosynthesis of different quinoid
substances are shown.
Abstract: This research has been conducted to study the method
of culture and comparing growth and biomass of Gracilaria corticata
cultured on rope and net for 50 days through two treatments (first
treatment: culture of alga on net and the second treatment: culture of
alga on rope and each treatment was repeated by four cases). During
culture period, the water of aquariums was replaced once every two
days for 40-50%. Also, 0.3-0.5 grams of urea fertilizer was added to
the culture environment for fertilization. Moreover, some of the
environmental factors such as pH, salinity and temperature of the
environment were measured on a daily basis. During the culture
period, extent of longitudinal growth of the species of both treatments
was equal. The said length was reached from 8-10 cm to 10.5-13 cm
accordingly. The resulted weight in repetitions of the first treatment
was higher than that of the second treatment in such a way as in the
first treatment, its weight reached from 10 grams to 21.119 grams and
in the second treatment, its weight reached from 10 grams to 17.663
grams. On a whole, it may be stated that that kind of alga being
studied has a considerable growth with respect to its volume. The
results have revealed that the percentage of daily growth and wet
weight at the end of the first treatment was higher than that of the
second treatment and it was registered as 0.934, 6.072 and 811.432 in
the first treatment and 0.797, 4.990 and 758.071 in the second
treatment respectively. This difference is significant (P
Abstract: Poly vinyl acetate (PVA)-based titania (TiO2)–carbon
nanotube composite nanofibers (PVA-TCCNs) with various
PVA-to-solvent ratios and PVA-based TiO2 composite nanofibers
(PVA-TN) were synthesized using an electrospinning process,
followed by thermal treatment. The photocatalytic activities of these
nanofibers in the degradation of airborne monocyclic aromatics under
visible-light irradiation were examined. This study focuses on the
application of these photocatalysts to the degradation of the target
compounds at sub-part-per-million indoor air concentrations. The
characteristics of the photocatalysts were examined using scanning
electron microscopy, X-ray diffraction, ultraviolet-visible
spectroscopy, and Fourier-transform infrared spectroscopy. For all the
target compounds, the PVA-TCCNs showed photocatalytic
degradation efficiencies superior to those of the reference PVA-TN.
Specifically, the average photocatalytic degradation efficiencies for
benzene, toluene, ethyl benzene, and o-xylene (BTEX) obtained using
the PVA-TCCNs with a PVA-to-solvent ratio of 0.3 (PVA-TCCN-0.3)
were 11%, 59%, 89%, and 92%, respectively, whereas those observed
using PVA-TNs were 5%, 9%, 28%, and 32%, respectively.
PVA-TCCN-0.3 displayed the highest photocatalytic degradation
efficiency for BTEX, suggesting the presence of an optimal
PVA-to-solvent ratio for the synthesis of PVA-TCCNs. The average
photocatalytic efficiencies for BTEX decreased from 11% to 4%, 59%
to 18%, 89% to 37%, and 92% to 53%, respectively, when the flow
rate was increased from 1.0 to 4.0 L min1. In addition, the average
photocatalytic efficiencies for BTEX increased 11% to ~0%, 59% to
3%, 89% to 7%, and 92% to 13%, respectively, when the input
concentration increased from 0.1 to 1.0 ppm. The prepared
PVA-TCCNs were effective for the purification of airborne aromatics
at indoor concentration levels, particularly when the operating
conditions were optimized.
Abstract: This paper presents powerful techniques for the
development of a new monitoring method based on multi-scale
entropy (MSE) in order to characterize the behaviour of the
concentrations of different gases present in the synthesis of Ammonia
and soft-sensor based on Principal Component Analysis (PCA).
Abstract: In this research paper were investigated the main
regularities of a radical bromination reaction of decalin. There had
been studied the temperature effect, durations of reaction, frequency
rate of process, a ratio of initial components, type and number of the
initiator on decalin bromination degree.
There were specified optimum conditions of synthesis of a
perbromodecalin by the method of a decalin bromination. There are
developed the technological flowchart of receiving a
perbromodecalin and the mass balance of process on the first and the
subsequent loadings of components.
The results of research of antibacterial and antifungal activity of
synthesized bromoderivatives have been represented.
Abstract: A nanocrystalline thin film of ZnSe was successfully
electrodeposited on copper substrate using a non-aqueous solution
and subsequently annealed in air at 400°C. XRD analysis indicates
the polycrystalline deposit of (111) plane in both the cases. The
sharpness of the peak increases due to annealing of the film and
average grain size increases to 20 nm to 27nm. SEM photograph
indicate that grains are uniform and densely distributed over the
surface. Annealing increases the average grain size by 20%. The EDS
spectroscopy shows the ratio of Zn & Se is 1.1 in case of annealed
film. AFM analysis indicates the average roughness of the film
reduces from 181nm to 165nm due to annealing of the film. The
bandgap also decreases from 2.71eV to 2.62eV.
Abstract: There has been a significant decline in active travel
and a massive increase in the use of car dependent travel in many
countries during the past two decades. Evidential risks for people’s
physical and mental health problems are correlated with this
increased use of motorized travel. These health related problems
range from overweight and obesity to increased air pollution. In
response to these rising concerns health professionals, traffic planers,
local authorities and others have introduced a variety of initiatives to
counterbalance the dominance of cars for daily journeys.
However, the nature of travel behavior change interventions,
which aim to reduce car use, are very complex and challenging
regarding their interactions with human behavior. To change travel
behavior at least two aspects have to be taken into consideration.
First, how to alter attitudes and perceptions toward the sustainable
and healthy modes of travel, in competition with experiences of
private car use. And second, how to make these behavior change
processes irreversible and sustainable. There are no comprehensive
models available to guide policy interventions to increase the level of
success of travel behavior change interventions across both these
dimensions.
A comprehensive theoretical framework is required in the effort to
optimize how to facilitate and guide the processes of data collection
and analysis to achieve the best possible guidelines for policy
makers. Regarding the gaps in the travel behavior change research
literature, this paper attempted to identify and suggest a
multidimensional framework in order to facilitate planning the
implemented travel behavior change interventions. A structured
mixed-method model is suggested to improve the analytic power of
the results according to the complexity of human behavior.
In order to recognize people’s attitudes towards a specific travel
mode, the Theory of Planned Behavior (TPB) was operationalized.
But in order to capture decision making processes the Transtheoretical
model of Behavior Change (TTM) was also used.
Consequently, the combination of these two theories (TTM and TPB)
has resulted in a synthesis with appropriate concepts to identify and
design an implemented travel behavior change interventions.
Abstract: In review the generalized data about different methods
of synthesis of biological activity halogenated di-, tri- and tetrahydroxyanthraquinones
is presented. The basic regularity of a
synthesis is analyzed. Action of temperature, pH, solubility, catalysts
and other factors on a reaction product yield is revealed.
Abstract: Doxorubicin, also known as Adriamycin, is an
anthracycline class of drug used in cancer chemotherapy. It is used in
the treatment of non-Hodgkin’s lymphoma, multiple myeloma, acute
leukemia, breast cancer, lung cancer, endometrium cancer and ovary
cancers. It functions via intercalating DNA and ultimately killing
cancer cells. The major side effects of doxorubicin are hair loss,
myelosuppression, nausea & vomiting, oesophagitis, diarrhea, heart
damage and liver dysfunction. The minor modifications in the
structure of compound exhibit large variation in the biological
activity, has prompted us to carry out the synthesis of sulfonamide
derivatives. Sulfonamide is an important feature with broad spectrum
of biological activity such as antiviral, antifungal, diuretics, antiinflammatory,
antibacterial and anticancer activities. Structure of the
synthesized compound N-(1-methyl-2-oxo-2-N-methyl anilinoethyl)
benzene sulfonamide confirmed by proton nuclear magnetic
resonance (1H NMR),13C NMR, Mass and FTIR spectroscopic tools
to assure the position of all protons and hence stereochemistry of the
molecule. Further we have reported the binding potential of
synthesized sulfonamide analogues in comparison to doxorubicin
drug using Auto Dock 4.2 software. Computational binding energy
(B.E.) and inhibitory constant (Ki) has been evaluated for the
synthesized compound in comparison of doxorubicin against Poly
(dA-dT).Poly (dA-dT) and Poly (dG-dC).Poly (dG-dC) sequences.
The in vitro cytotoxic study against human breast cancer cell lines
confirms the better anticancer activity of the synthesized compound
over currently in use anticancer drug doxorubicin. The IC50 value of
the synthesized compound is 7.12 μM whereas for doxorubicin is 7.2
μM.
Abstract: In review the generalized data about different methods
of synthesis of biological activity aminated hydroxyanthraquinones is
presented. The basic regularity of a synthesis is analyzed. Action of
temperature, pH, solubility, catalysts and other factors on a reaction
product yield is revealed.
Abstract: In this article a comparison was made between Cu and
TiO2 supported catalysts on activated carbon for ozone
decomposition reaction. The activated carbon support in the case of
TiO2/AC sample was prepared by physicochemical pyrolysis and for
Cu/AC samples the supports are chemically modified carbons. The
prepared catalysts were synthesized by impregnation method. The
samples were annealed in two different regimes- in air and under
vacuum. To examine adsorption efficiency of the samples BET
method was used. All investigated catalysts supported on chemically
modified carbons have higher specific surface area compared to the
specific surface area of TiO2 supported catalysts, varying in the range
590÷620 m2/g. The method of synthesis of the precursors had
influenced catalytic activity.
Abstract: This paper presents two types of microstrip bandpass
filter (BPF) at microwave frequencies. The first one is a tunable BPF
using planar patch resonators based on a varactor diode. The filter is
formed by a triple mode circular patch resonator with two pairs of
slots, in which the varactor diodes are connected. Indeed, this filter is
initially centered at 2.4 GHz; the center frequency of the tunable
patch filter could be tuned up to 1.8 GHz simultaneously with the
bandwidth, reaching high tuning ranges. Lossless simulations were
compared to those considering the substrate dielectric, conductor
losses and the equivalent electrical circuit model of the tuning
element in order to assess their effects. Within these variations,
simulation results showed insertion loss better than 2 dB and return
loss better than 10 dB over the passband. The second structure is a
BPF for ultra-wideband (UWB) applications based on multiple-mode
resonator (MMR) and rectangular-shaped defected ground structure
(DGS). This filter, which is compact size of 25.2 x 3.8 mm2, provides
in the pass band an insertion loss of 0.57 dB and a return loss greater
than 12 dB. The proposed filters presents good performances and the
simulation results are in satisfactory agreement with the
experimentation ones reported elsewhere.
Abstract: Composite material based on Fe3Si micro-particles
and Mn-Zn nano-ferrite was prepared using powder metallurgy
technology. The sol-gel followed by autocombustion process was
used for synthesis of Mn0.8Zn0.2Fe2O4 ferrite. 3 wt.% of mechanically
milled ferrite was mixed with Fe3Si powder alloy. Mixed micro-nano
powder system was homogenized by the Resonant Acoustic Mixing
using ResodynLabRAM Mixer. This non-invasive homogenization
technique was used to preserve spherical morphology of Fe3Si
powder particles. Uniaxial cold pressing in the closed die at pressure
600 MPa was applied to obtain a compact sample. Microwave
sintering of green compact was realized at 800°C, 20 minutes, in air.
Density of the powders and composite was measured by
Hepycnometry. Impulse excitation method was used to measure
elastic properties of sintered composite. Mechanical properties were
evaluated by measurement of transverse rupture strength (TRS) and
Vickers hardness (HV). Resistivity was measured by 4 point probe
method. Ferrite phase distribution in volume of the composite was
documented by metallographic analysis.
It has been found that nano-ferrite particle distributed among
micro- particles of Fe3Si powder alloy led to high relative density
(~93%) and suitable mechanical properties (TRS >100 MPa, HV
~1GPa, E-modulus ~140 GPa) of the composite. High electric
resistivity (R~6.7 ohm.cm) of prepared composite indicate their
potential application as soft magnetic material at medium and high
frequencies.
Abstract: Random epistemologies and hash tables have garnered
minimal interest from both security experts and experts in the last
several years. In fact, few information theorists would disagree with
the evaluation of expert systems. In our research, we discover how
flip-flop gates can be applied to the study of superpages. Though
such a hypothesis at first glance seems perverse, it is derived from
known results.
Abstract: PLA emerged as a promising polymer because of its
property as a compostable, biodegradable thermoplastic made from
renewable sources. PLA can be polymerized from monomers
(Lactide or Lactic acid) obtained by fermentation processes from
renewable sources such as corn starch or sugarcane. For PLA
synthesis, ring opening polymerization (ROP) of Lactide monomer is
one of the preferred methods. In the literature, the technique mainly
developed for ROP of PLA is based on metal/bimetallic catalyst (Sn,
Zn and Al) or other organic catalysts in suitable solvent. However,
the PLA synthesized using such catalysts may contain trace elements
of the catalyst which may cause toxicity. This work estimated the
usefulness and drawbacks of using different catalysts as well as effect
of alternative energies and future aspects for PLA production.