Abstract: Wall-surface jet induced by the dielectric barrier
discharge (DBD) has been proposed as an actuator for active flow
control in aerodynamic applications. Discharge plasma evolution of
the DBD plasma actuator was simulated based on a simple fluid model,
in which the electron, one type of positive ion and negative ion were
taken into account. Two-dimensional simulation was conducted, and
the results are in agreement with the insights obtained from
experimental studies. The simulation results indicate that the discharge
mode changes depending on applied voltage slope; when the applied
voltage is positive-going with high applied voltage slope, the
corona-type discharge mode turns into the streamer-type discharge
mode and the threshold voltage slope is around 300 kV/ms in this
simulation. The characteristics of the electrohydrodynamic (EHD)
force, which is the source of the wall-surface jet, also change
depending on the discharge mode; the tentative peak value of the EHD
force during the positive-going voltage phase is saturated by the
periodical formation of the streamer-type discharge.
Abstract: This paper proposes a meta-heuristic called Ant Colony Optimization to solve multi-objective production problems. The multi-objective function is to minimize lead time and work in process. The problem is related to the decision variables, i.e.; distance and process time. According to decision criteria, the mathematical model is formulated. In order to solve the model an ant colony optimization approach has been developed. The proposed algorithm is parameterized by the number of ant colonies and the number of pheromone trails. One example is given to illustrate the effectiveness of the proposed model. The proposed formulations; Max-Min Ant system are then used to solve the problem and the results evaluate the performance and efficiency of the proposed algorithm using simulation.
Abstract: At the previous study of new metal gasket, contact
width and contact stress were important design parameter for
optimizing metal gasket performance. However, the range of contact
stress had not been investigated thoroughly. In this study, we
conducted a gasket design optimization based on an elastic and plastic
contact stress analysis considering forming effect using FEM. The
gasket model was simulated by using two simulation stages which is
forming and tightening simulation. The optimum design based on an
elastic and plastic contact stress was founded. Final evaluation was
determined by helium leak quantity to check leakage performance of
both type of gaskets. The helium leak test shows that a gasket based
on the plastic contact stress design better than based on elastic stress
design.
Abstract: The objective of this work which is based on the
approach of simultaneous engineering is to contribute to the
development of a CIM tool for the synthesis of functional design
dimensions expressed by average values and tolerance intervals. In
this paper, the dispersions method known as the Δl method which
proved reliable in the simulation of manufacturing dimensions is
used to develop a methodology for the automation of the simulation.
This methodology is constructed around three procedures. The first
procedure executes the verification of the functional requirements by
automatically extracting the functional dimension chains in the
mechanical sub-assembly. Then a second procedure performs an
optimization of the dispersions on the basis of unknown variables.
The third procedure uses the optimized values of the dispersions to
compute the optimized average values and tolerances of the
functional dimensions in the chains. A statistical and cost based
approach is integrated in the methodology in order to take account of
the capabilities of the manufacturing processes and to distribute
optimal values among the individual components of the chains.
Abstract: We investigate an asymmetric connections model with a
dynamic network formation process, using an agent based simulation.
We permit heterogeneity of agents- value. Valuable persons seem
to have many links on real social networks. We focus on this
point of view, and examine whether valuable agents change the
structures of the terminal networks. Simulation reveals that valuable
agents diversify the terminal networks. We can not find evidence that
valuable agents increase the possibility that star networks survive the
dynamic process. We find that valuable agents disperse the degrees
of agents in each terminal network on an average.
Abstract: The quantum mechanics simulation was applied for
calculating the interaction force between 2 molecules based on atomic level. For the simple extractive distillation system, it is ternary
components consisting of 2 closed boiling point components (A,lower boiling point and B, higher boiling point) and solvent (S). The
quantum mechanics simulation was used to calculate the intermolecular force (interaction force) between the closed boiling
point components and solvents consisting of intermolecular between
A-S and B-S.
The requirement of the promising solvent for extractive distillation
is that solvent (S) has to form stronger intermolecular force with only
one component than the other component (A or B). In this study, the
systems of aromatic-aromatic, aromatic-cycloparaffin, and paraffindiolefin
systems were selected as the demonstration for solvent
selection. This study defined new term using for screening the solvents called relative interaction force which is calculated from the
quantum mechanics simulation. The results showed that relative
interaction force gave the good agreement with the literature data
(relative volatilities from the experiment). The reasons are discussed. Finally, this study suggests that quantum mechanics results can improve the relative volatility estimation for screening the solvents leading to reduce time and money consuming
Abstract: In recent years Operational Transconductance Amplifier based high frequency integrated circuits, filters and systems have been widely investigated. The usefulness of OTAs over conventional OP-Amps in the design of both first order and second order active filters are well documented. This paper discusses some of the tunability issues using the Matlab/Simulink® software which are previously unreported for any commercial OTA. Using the simulation results two first order voltage controlled all pass filters with phase tuning capability are proposed.
Abstract: Modeling and vibration of a flexible link manipulator
with tow flexible links and rigid joints are investigated which can
include an arbitrary number of flexible links. Hamilton principle and
finite element approach is proposed to model the dynamics of
flexible manipulators. The links are assumed to be deflection due to
bending. The association between elastic displacements of links is
investigated, took into account the coupling effects of elastic motion
and rigid motion. Flexible links are treated as Euler-Bernoulli beams
and the shear deformation is thus abandoned. The dynamic behavior
due to flexibility of links is well demonstrated through numerical
simulation. The rigid-body motion and elastic deformations are
separated by linearizing the equations of motion around the rigid
body reference path. Simulation results are shown on for both
position and force trajectory tracking tasks in the presence of varying
parameters and unknown dynamics remarkably well. The proposed
method can be used in both dynamic simulation and controller
design.
Abstract: Sensor networks are often deployed in unattended
environments, thus leaving these networks vulnerable to false data
injection attacks in which an adversary injects forged reports into the
network through compromised nodes, with the goal of deceiving the
base station or depleting the resources of forwarding nodes. Several
research solutions have been recently proposed to detect and drop such
forged reports during the forwarding process. Each design can provide
the equivalent resilience in terms of node compromising. However,
their energy consumption characteristics differ from each other. Thus,
employing only a single filtering scheme for a network is not a
recommendable strategy in terms of energy saving. It's very important
the threshold determination for message authentication to identify. We
propose the recursive contract net protocols which less energy level of
terminal node in wireless sensor network.
Abstract: The compression-absorption heat pump (C-A HP), one
of the promising heat recovery equipments that make process hot
water using low temperature heat of wastewater, was evaluated by
computer simulation. A simulation program was developed based on
the continuity and the first and second laws of thermodynamics. Both
the absorber and desorber were modeled using UA-LMTD method. In
order to prevent an unfeasible temperature profile and to reduce
calculation errors from the curved temperature profile of a mixture,
heat loads were divided into lots of segments. A single-stage
compressor was considered. A compressor cooling load was also
taken into account. An isentropic efficiency was computed from the
map data. Simulation conditions were given based on the system
consisting of ordinarily designed components. The simulation results
show that most of the total entropy generation occurs during the
compression and cooling process, thus suggesting the possibility that
system performance can be enhanced if a rectifier is introduced.
Abstract: Three dimensional simulations are carried out to estimate the effect of wind direction, wind speed and geometry on the flow and dispersion of vehicular pollutant in a street canyon. The pollutant sources are motor vehicles passing between the two buildings. Suitable emission factors for petrol and diesel vehicles at varying vehicle speed are used for the estimation of the rate of emission from the streets. The dispersion of automobile pollutant released from the street is simulated by introducing vehicular emission source term as a fixed-flux boundary condition at the ground level over the road. The emission source term is suitably calculated by adopting emission factors from literature for varying conditions of street traffic. It is observed that increase in wind angle disturbs the symmetric pattern of pollution distribution along the street length. The concentration increases in the far end of the street as compared to the near end.
Abstract: As in today's semiconductor industries test costs can make up to 50 percent of the total production costs, an efficient test error detection becomes more and more important. In this paper, we present a new machine learning approach to test error detection that should provide a faster recognition of test system faults as well as an improved test error recall. The key idea is to learn a classifier ensemble, detecting typical test error patterns in wafer test results immediately after finishing these tests. Since test error detection has not yet been discussed in the machine learning community, we define central problem-relevant terms and provide an analysis of important domain properties. Finally, we present comparative studies reflecting the failure detection performance of three individual classifiers and three ensemble methods based upon them. As base classifiers we chose a decision tree learner, a support vector machine and a Bayesian network, while the compared ensemble methods were simple and weighted majority vote as well as stacking. For the evaluation, we used cross validation and a specially designed practical simulation. By implementing our approach in a semiconductor test department for the observation of two products, we proofed its practical applicability.
Abstract: The energy consumption and delay in read/write
operation of conventional SRAM is investigated analytically as well
as by simulation. Explicit analytical expressions for the energy
consumption and delay in read and write operation as a function of
device parameters and supply voltage are derived. The expressions are
useful in predicting the effect of parameter changes on the energy
consumption and speed as well as in optimizing the design of
conventional SRAM. HSPICE simulation in standard 0.25μm CMOS
technology confirms precision of analytical expressions derived from
this paper.
Abstract: In this paper, a predator-prey model with Holling III type functional response is studied. It is interesting that the system is always uniformly persistent, which yields the existence of at least one positive periodic solutions for the corresponding periodic system. The result improves the corresponding ones in [11]. Moreover, an example is illustrated to verify the results by simulation.
Abstract: Colored Petri Nets (CPN) are very known kind of
high level Petri nets. With sound and complete semantics, rewriting
logic is one of very powerful logics in description and verification of
non-deterministic concurrent systems. Recently, CPN semantics are
defined in terms of rewriting logic, allowing us to built models by
formal reasoning. In this paper, we propose an automatic translation
of CPN to the rewriting logic language Maude. This tool allows
graphical editing and simulating CPN. The tool allows the user
drawing a CPN graphically and automatic translating the graphical
representation of the drawn CPN to Maude specification. Then,
Maude language is used to perform the simulation of the resulted
Maude specification. It is the first rewriting logic based environment
for this category of Petri Nets.
Abstract: On the basis of Bayesian inference using the
maximizer of the posterior marginal estimate, we carry out phase
unwrapping using multiple interferograms via generalized mean-field
theory. Numerical calculations for a typical wave-front in remote
sensing using the synthetic aperture radar interferometry, phase
diagram in hyper-parameter space clarifies that the present method
succeeds in phase unwrapping perfectly under the constraint of
surface- consistency condition, if the interferograms are not corrupted
by any noises. Also, we find that prior is useful for extending a phase
in which phase unwrapping under the constraint of the
surface-consistency condition. These results are quantitatively
confirmed by the Monte Carlo simulation.
Abstract: Determination of wellbore problems during a
production/injection process might be evaluated thorough
temperature log analysis. Other applications of this kind of log
analysis may also include evaluation of fluid distribution analysis
along the wellbore and identification of anomalies encountered
during production/injection process. While the accuracy of such
prediction is paramount, the common method of determination of a
wellbore temperature log includes use of steady-state energy balance
equations, which hardly describe the real conditions as observed in
typical oil and gas flowing wells during production operation; and
thus increase level of uncertainties. In this study, a practical method
has been proposed through development of a simplified semianalytical
model to apply for predicting temperature profile along the
wellbore. The developed model includes an overall heat transfer
coefficient accounting all modes of heat transferring mechanism,
which has been focused on the prediction of a temperature profile as
a function of depth for the injection/production wells. The model has
been validated with the results obtained from numerical simulation.
Abstract: Carbon dioxide capture process has been simulated
and studied under different process conditions. It has been shown
that several process parameters such as lean amine temperature,
number of adsorber stages, number of stripper stages and stripper
pressure affect different process conditions and outputs such as
carbon dioxide removal and reboiler duty. It may be concluded that
the simulation of carbon dioxide capture process can help to estimate
the best process conditions.
Abstract: Simulation is a very helpful and valuable work tool in
manufacturing. It can be used in industrial field allowing the
system`s behavior to be learnt and tested. Simulation provides a low
cost, secure and fast analysis tool. It also provides benefits, which
can be reached with many different system configurations. Topics to
be discussed include: Applications, Modeling, Validating, Software
and benefits of simulation. This paper provides a comprehensive
literature review on research efforts in simulation.
Abstract: The response of growth and yield of rainfed-chickpea
to population density should be evaluated based on long-term
experiments to include the climate variability. This is achievable just
by simulation. In this simulation study, this evaluation was done by
running the CYRUS model for long-term daily weather data of five
locations in Iran. The tested population densities were 7 to 59 (with
interval of 2) stands per square meter. Various functions, including
quadratic, segmented, beta, broken linear, and dent-like functions,
were tested. Considering root mean square of deviations and linear
regression statistics [intercept (a), slope (b), and correlation
coefficient (r)] for predicted versus observed variables, the quadratic
and broken linear functions appeared to be appropriate for describing
the changes in biomass and grain yield, and in harvest index,
respectively. Results indicated that in all locations, grain yield tends
to show increasing trend with crowding the population, but
subsequently decreases. This was also true for biomass in five
locations. The harvest index appeared to have plateau state across
low population densities, but decreasing trend with more increasing
density. The turning point (optimum population density) for grain
yield was 30.68 stands per square meter in Isfahan, 30.54 in Shiraz,
31.47 in Kermanshah, 34.85 in Tabriz, and 32.00 in Mashhad. The
optimum population density for biomass ranged from 24.6 (in
Tabriz) to 35.3 stands per square meter (Mashhad). For harvest index
it varied between 35.87 and 40.12 stands per square meter.