Abstract: Time interleaved sigma-delta (TIΣΔ) architecture is a
potential candidate for high bandwidth analog to digital converters
(ADC) which remains a bottleneck for software and cognitive radio
receivers. However, the performance of the TIΣΔ architecture is
limited by the unavoidable gain and offset mismatches resulting
from the manufacturing process. This paper presents a novel digital
calibration method to compensate the gain and offset mismatch
effect. The proposed method takes advantage of the reconstruction
digital signal processing on each channel and requires only few logic
components for implementation. The run time calibration is estimated
to 10 and 15 clock cycles for offset cancellation and gain mismatch
calibration respectively.
Abstract: This paper proposes a fast tree join scheme to provide
seamless multicast handover in the mobile networks based on the Fast
Mobile IPv6 (FMIPv6). In the existing FMIPv6-based multicast
handover scheme, the bi-directional tunnelling or the remote
subscription is employed with the packet forwarding from the previous
access router (AR) to the new AR. In general, the remote subscription
approach is preferred to the bi-directional tunnelling one, since in the
remote subscription scheme we can exploit an optimized multicast
path from a multicast source to many mobile receivers. However, in
the remote subscription scheme, if the tree joining operation takes a
long time, the amount of data packets to be forwarded and buffered for
multicast handover will increase, and thus the corresponding buffer
may overflow, which results in severe packet losses. In order to reduce
these costs associated with packet forwarding and buffering, this paper
proposes the fast join to multicast tree, in which the new AR will join
the multicast tree as fast as possible, so that the new multicast data
packets can also arrive at the new AR, by which the packet forwarding
and buffering costs can be reduced. From numerical analysis, it is
shown that the proposed scheme can give better performance than the
existing FMIPv6-based multicast handover schemes in terms of the
multicast packet delivery costs.
Abstract: QoS Routing aims to find paths between senders and
receivers satisfying the QoS requirements of the application which
efficiently using the network resources and underlying routing
algorithm to be able to find low-cost paths that satisfy given QoS
constraints. The problem of finding least-cost routing is known to be
NP-hard or complete and some algorithms have been proposed to
find a near optimal solution. But these heuristics or algorithms either
impose relationships among the link metrics to reduce the complexity
of the problem which may limit the general applicability of the
heuristic, or are too costly in terms of execution time to be applicable
to large networks. In this paper, we concentrate an algorithm that
finds a near-optimal solution fast and we named this algorithm as
optimized Delay Constrained Routing (ODCR), which uses an
adaptive path weight function together with an additional constraint
imposed on the path cost, to restrict search space and hence ODCR
finds near optimal solution in much quicker time.
Abstract: This study aims to identify processes, current
situations, and issues of recycling systems for four home appliances,
namely, air conditioners, television receivers, refrigerators, and
washing machines, among e-wastes in China and Japan for
understanding and comparison of their characteristics. In accordance
with results of a literature search, review of information disclosed
online, and questionnaire survey conducted, conclusions of the study
boil down to:
(1)The results show that in Japan most of the home appliances
mentioned above have been collected through home appliance
recycling tickets, resulting in an issue of “requiring some effort" in
treatment and recycling stages, and most plants have contracted out
their e-waste recycling.
(2)It is found out that advantages of the recycling system in Japan
include easiness to monitor concrete data and thorough
environmental friendliness ensured while its disadvantages include
illegal dumping and export. It becomes apparent that advantages of
the recycling system in China include a high reuse rate, low
treatment cost, and fewer illegal dumping while its disadvantages
include less safe reused products, environmental pollution caused by
e-waste treatment, illegal import, and difficulty in obtaining data.
Abstract: In diversity rich environments, such as in Ultra-
Wideband (UWB) applications, the a priori determination of the
number of strong diversity branches is difficult, because of the considerably large number of diversity paths, which are characterized
by a variety of power delay profiles (PDPs). Several
Rake implementations have been proposed in the past, in order to reduce the number of the estimated and combined paths. To this
aim, we introduce two adaptive Rake receivers, which combine
a subset of the resolvable paths considering simultaneously the
quality of both the total combining output signal-to-noise ratio (SNR) and the individual SNR of each path. These schemes achieve
better adaptation to channel conditions compared to other known receivers, without further increasing the complexity. Their performance
is evaluated in different practical UWB channels, whose models are based on extensive propagation measurements. The
proposed receivers compromise between the power consumption,
complexity and performance gain for the additional paths, resulting in important savings in power and computational resources.
Abstract: The purpose of this research is to develop and apply the
RSCMAC to enhance the dynamic accuracy of Global Positioning
System (GPS). GPS devices provide services of accurate positioning,
speed detection and highly precise time standard for over 98% area on
the earth. The overall operation of Global Positioning System includes
24 GPS satellites in space; signal transmission that includes 2
frequency carrier waves (Link 1 and Link 2) and 2 sets random
telegraphic codes (C/A code and P code), on-earth monitoring stations
or client GPS receivers. Only 4 satellites utilization, the client position
and its elevation can be detected rapidly. The more receivable
satellites, the more accurate position can be decoded. Currently, the
standard positioning accuracy of the simplified GPS receiver is greatly
increased, but due to affected by the error of satellite clock, the
troposphere delay and the ionosphere delay, current measurement
accuracy is in the level of 5~15m. In increasing the dynamic GPS
positioning accuracy, most researchers mainly use inertial navigation
system (INS) and installation of other sensors or maps for the
assistance. This research utilizes the RSCMAC advantages of fast
learning, learning convergence assurance, solving capability of
time-related dynamic system problems with the static positioning
calibration structure to improve and increase the GPS dynamic
accuracy. The increasing of GPS dynamic positioning accuracy can be
achieved by using RSCMAC system with GPS receivers collecting
dynamic error data for the error prediction and follows by using the
predicted error to correct the GPS dynamic positioning data. The
ultimate purpose of this research is to improve the dynamic positioning
error of cheap GPS receivers and the economic benefits will be
enhanced while the accuracy is increased.
Abstract: QoS Routing aims to find paths between senders and
receivers satisfying the QoS requirements of the application which
efficiently using the network resources and underlying routing
algorithm to be able to find low-cost paths that satisfy given QoS
constraints. The problem of finding least-cost routing is known to be
NP hard or complete and some algorithms have been proposed to
find a near optimal solution. But these heuristics or algorithms either
impose relationships among the link metrics to reduce the complexity
of the problem which may limit the general applicability of the
heuristic, or are too costly in terms of execution time to be applicable
to large networks. In this paper, we analyzed two algorithms namely
Characterized Delay Constrained Routing (CDCR) and Optimized
Delay Constrained Routing (ODCR). The CDCR algorithm dealt an
approach for delay constrained routing that captures the trade-off
between cost minimization and risk level regarding the delay
constraint. The ODCR which uses an adaptive path weight function
together with an additional constraint imposed on the path cost, to
restrict search space and hence ODCR finds near optimal solution in
much quicker time.
Abstract: In this article, we introduce a mechanism by which the same concept of differentiated services used in network transmission can be applied to provide quality of service levels to pervasive systems applications. The classical DiffServ model, including marking and classification, assured forwarding, and expedited forwarding, are all utilized to create quality of service guarantees for various pervasive applications requiring different levels of quality of service. Through a collection of various sensors, personal devices, and data sources, the transmission of contextsensitive data can automatically occur within a pervasive system with a given quality of service level. Triggers, initiators, sources, and receivers are four entities labeled in our mechanism. An explanation of the role of each is provided, and how quality of service is guaranteed.
Abstract: IEEE 802.15.4a impulse radio-time hopping ultra wide
band (IR-TH UWB) physical layer, due to small duty cycle and very
short pulse widths is robust against multipath propagation. However,
scattering and reflections with the large number of obstacles in indoor
channel environments, give rise to dense multipath fading. It imposes
serious problem to optimum Rake receiver architectures, for which
very large number of fingers are needed. Presence of strong noise
also affects the reception of fine pulses having extremely low power
spectral density. A robust SRake receiver for IEEE 802.15.4a IRTH
UWB in dense multipath and additive white Gaussian noise
(AWGN) is proposed to efficiently recover the weak signals with
much reduced complexity. It adaptively increases the signal to noise
(SNR) by decreasing noise through a recursive least square (RLS)
algorithm. For simulation, dense multipath environment of IEEE
802.15.4a industrial non line of sight (NLOS) is employed. The power
delay profile (PDF) and the cumulative distribution function (CDF)
for the respective channel environment are found. Moreover, the error
performance of the proposed architecture is evaluated in comparison
with conventional SRake and AWGN correlation receivers. The
simulation results indicate a substantial performance improvement
with very less number of Rake fingers.
Abstract: Navigation is the processes of monitoring and
controlling the movement of an object from one place to another.
Currently, Global Positioning System (GPS) is the main navigation
system used all over the world for navigation applications. GPS
receiver receives signals from at least three satellites to locate and
display itself. Displayed positioning information is updated
continuously. Update rate is the number of times per second that a
display is illuminated. The speed of update is governed by receiver
update rate. A higher update rate decreases display lag time and
improves distance measurements and tracking especially when
moving on a curvy route. The majority of GPS receivers used
nowadays are updated every second continuously. This period is
considered reasonable for some applications while it is long relatively
for high speed applications. In this paper, the suitability and
feasibility of GPS receiver with different update rates will be
evaluated for various applications according to the level of speed and
update rate needed for particular applications.
Abstract: Attitude Determination (AD) of a spacecraft using the
phase measurements of the Global Navigation Satellite System
(GNSS) is an active area of research. Various attitude determination
algorithms have been developed in yester years for spacecrafts using
different sensors but the last two decades have witnessed a
phenomenal increase in research related with GPS receivers as a
stand-alone sensor for determining the attitude of satellite using the
phase measurements of the signals from GNSS. The GNSS-based
Attitude determination algorithms have been experimented in many
real missions. The problem of AD algorithms using GNSS phase
measurements has two important parts; the ambiguity resolution and
the determining of attitude. Ambiguity resolution is the widely
addressed topic in literature for implementing the AD algorithm
using GNSS phase measurements for achieving the accuracy of
millimeter level. This paper broadly overviews the different
techniques for resolving the integer ambiguities encountered in AD
using GNSS phase measurements.
Abstract: Sub-prime mortgage crisis which began in the US is
regarded as the most economic crisis since the Great Depression in the
early 20th century. Especially, hidden problems on efficient operation
of a business were disclosed at a time and many financial institutions
went bankrupt and filed for court receivership. The collapses of
physical market lead to bankruptcy of manufacturing and construction
businesses. This study is to analyze dynamic efficiency of construction
businesses during the five years at the turn of the global financial
crisis. By discovering the trend and stability of efficiency of a
construction business, this study-s objective is to improve
management efficiency of a construction business in the
ever-changing construction market. Variables were selected by
analyzing corporate information on top 20 construction businesses in
Korea and analyzed for static efficiency in 2008 and dynamic
efficiency between 2006 and 2010. Unlike other studies, this study
succeeded in deducing efficiency trend and stability of a construction
business for five years by using the DEA/Window model. Using the
analysis result, efficient and inefficient companies could be figured
out. In addition, relative efficiency among DMU was measured by
comparing the relationship between input and output variables of
construction businesses. This study can be used as a literature to
improve management efficiency for companies with low efficiency
based on efficiency analysis of construction businesses.
Abstract: The major problem that wireless communication
systems undergo is multipath fading caused by scattering of the
transmitted signal. However, we can treat multipath propagation as
multiple channels between the transmitter and receiver to improve
the signal-to-scattering-noise ratio. While using Single Input
Multiple Output (SIMO) systems, the diversity receivers extract
multiple signal branches or copies of the same signal received from
different channels and apply gain combining schemes such as Root
Mean Square Gain Combining (RMSGC). RMSGC asymptotically
yields an identical performance to that of the theoretically optimal
Maximum Ratio Combining (MRC) for values of mean Signal-to-
Noise-Ratio (SNR) above a certain threshold value without the need
for SNR estimation. This paper introduces an improvement of
RMSGC using two different issues. We found that post-detection and
de-noising the received signals improve the performance of RMSGC
and lower the threshold SNR.
Abstract: This study aims to identify the current situation and
problems of environmental statement for major four home appliances
(refrigerators, washing machines, air conditioners and television
receivers) sold at online stores in Japan, and then to suggest how to
improve the situation, through a questionnaire survey conducted
among businesses that operate online stores and online malls with
multiple online stores. Results of the study boil down to:
(1) It is found out that environmental statement for the home
appliances at online stores have four problems; (i) less information
on “three Rs" and “chemical substances" than the one on “energy
conservation", (ii) cost for providing environmental statement, (iii)
issues associated with a label and mark placement, and (iv) issues
associated with energy conservation statement.
(2) Improvements are suggested for each of the four problems listed
above, and shown are (i) the effectiveness of, and need to promote, a
label and mark placement, (ii) cost burden on buyers, and (iii) need
of active efforts made by businesses and of dissemination of legal
regulations to businesses.
Abstract: In this paper, a post processing scheme is suggested
for improvement of Bit Error-Rate (BER) in optical fiber
transmission receivers. The developed scheme has been tested on
optical fiber systems operating with a non-return-to-zero (NRZ)
format at transmission rates of up to 10Gbps. The transmission
system considered is based on well known transmitters and receivers
blocks operating at wavelengths in the region of 1550 nm using a
standard single mode fiber. Performance of improved detected
signals has been evaluated via the analysis of quality factor and
computed bit error rates. Numerical simulations have shown a
noticeable improvement of the system BER after implementation of
the suggested post processing operation on the detected electrical
signals.
Abstract: In this paper, the noise maps for the area encircled by
the Second Ring Road in Riyadh city are developed based on real
measured data. Sound level meters, GPS receivers to determine
measurement position, a database program to manage the measured
data, and a program to develop the maps are used. A baseline noise
level has been established at each short-term site so subsequent
monitoring may be conducted to describe changes in Riyadh-s noise
environment. Short-term sites are used to show typical daytime and
nighttime noise levels at specific locations by short duration grab
sampling.
Abstract: In this paper, a double balanced radio frequency multiplier
is presented which is customized for transmitted reference
ultra wideband (UWB) receivers. The multiplier uses 90nm model
parameters and exploits compensating transistors to provide controllable
gain for a Gilbert core. After performing periodic and quasiperiodic
non linear analyses the RF mixer (multiplier) achieves a
voltage conversion gain of 16 dB and a DSB noise figure of 8.253
dB with very low power consumption. A high degree of LO to RF
isolation (in the range of -94dB), RF to IF isolation (in the range of
-95dB) and LO to IF isolation (in the range of -143dB) is expected
for this design with an input-referred IP3 point of -1.93 dBm and an
input referred 1 dB compression point of -10.67dBm. The amount of
noise at the output is 7.7 nV/√Hz when the LO input is driven by
a 10dBm signal. The mixer manifests better results when compared
with other reported multiplier circuits and its Zero-IF performance
ensures its applicability as TR-UWB multipliers.
Abstract: We consider optimal channel equalization for MIMO
(multi-input/multi-output) time-varying channels in the sense of
MMSE (minimum mean-squared-error), where the observation noise
can be non-stationary. We show that all ZF (zero-forcing) receivers
can be parameterized in an affine form which eliminates completely
the ISI (inter-symbol-interference), and optimal channel equalizers
can be designed through minimization of the MSE (mean-squarederror)
between the detected signals and the transmitted signals,
among all ZF receivers. We demonstrate that the optimal channel
equalizer is a modified Kalman filter, and show that under the AWGN
(additive white Gaussian noise) assumption, the proposed optimal
channel equalizer minimizes the BER (bit error rate) among all
possible ZF receivers. Our results are applicable to optimal channel
equalization for DWMT (discrete wavelet multitone), multirate transmultiplexers,
OFDM (orthogonal frequency division multiplexing),
and DS (direct sequence) CDMA (code division multiple access)
wireless data communication systems. A design algorithm for optimal
channel equalization is developed, and several simulation examples
are worked out to illustrate the proposed design algorithm.
Abstract: This paper focuses on wormhole attacks detection in wireless sensor networks. The wormhole attack is particularly challenging to deal with since the adversary does not need to compromise any nodes and can use laptops or other wireless devices to send the packets on a low latency channel. This paper introduces an easy and effective method to detect and locate the wormholes: Since beacon nodes are assumed to know their coordinates, the straight line distance between each pair of them can be calculated and then compared with the corresponding hop distance, which in this paper equals hop counts × node-s transmission range R. Dramatic difference may emerge because of an existing wormhole. Our detection mechanism is based on this. The approximate location of the wormhole can also be derived in further steps based on this information. To the best of our knowledge, our method is much easier than other wormhole detecting schemes which also use beacon nodes, and to those have special requirements on each nodes (e.g., GPS receivers or tightly synchronized clocks or directional antennas), ours is more economical. Simulation results show that the algorithm is successful in detecting and locating wormholes when the density of beacon nodes reaches 0.008 per m2.
Abstract: In this paper we present a soft timing phase estimation (STPE) method for wireless mobile receivers operating in low signal to noise ratios (SNRs). Discrete Polyphase Matched (DPM) filters, a Log-maximum a posterior probability (MAP) and/or a Soft-output Viterbi algorithm (SOVA) are combined to derive a new timing recovery (TR) scheme. We apply this scheme to wireless cellular communication system model that comprises of a raised cosine filter (RCF), a bit-interleaved turbo-coded multi-level modulation (BITMM) scheme and the channel is assumed to be memory-less. Furthermore, no clock signals are transmitted to the receiver contrary to the classical data aided (DA) models. This new model ensures that both the bandwidth and power of the communication system is conserved. However, the computational complexity of ideal turbo synchronization is increased by 50%. Several simulation tests on bit error rate (BER) and block error rate (BLER) versus low SNR reveal that the proposed iterative soft timing recovery (ISTR) scheme outperforms the conventional schemes.