Abstract: This paper presents the design and fabrication of a
novel piezoelectric actuator for a gas micro pump with check valve
having the advantages of miniature size, light weight and low power
consumption. The micro pump is designed to have eight major
components, namely a stainless steel upper cover layer, a piezoelectric
actuator, a stainless steel diaphragm, a PDMS chamber layer, two
stainless steel channel layers with two valve seats, a PDMS check
valve layer with two cantilever-type check valves and an acrylic
substrate. A prototype of the gas micro pump, with a size of 52 mm ×
50 mm × 5.0 mm, is fabricated by precise manufacturing. This device
is designed to pump gases with the capability of performing the
self-priming and bubble-tolerant work mode by maximizing the stroke
volume of the membrane as well as the compression ratio via
minimization of the dead volume of the micro pump chamber and
channel. By experiment apparatus setup, we can get the real-time
values of the flow rate of micro pump and the displacement of the
piezoelectric actuator, simultaneously. The gas micro pump obtained
higher output performance under the sinusoidal waveform of 250 Vpp.
The micro pump achieved the maximum pumping rates of 1185
ml/min and back pressure of 7.14 kPa at the corresponding frequency
of 120 and 50 Hz.
Abstract: In this work, the Ictalurus punctatus species estimated
available physical habitat is compared with the estimated physical
habitat for the same but modified river reach, with the aim of creating
a linear park, along a length of 5 500 m.
To determine the effect of ecological park construction, on
physical habitat of the Lerma river stretch of study, first, the available
habitat for the Ictalurus punctatus species was estimated through the
simulation of the physical habitat, by using surveying, hydraulics,
and habitat information gotten at the river reach in its actual situation.
Second, it was estimated the available habitat for the above species,
upon the simulation of the physical habitat through the proposed
modification for the ecological park creation. Third, it is presented a
comparison between both scenarios in terms of available habitat
estimated for Ictalurus punctatus species, concluding that in cases of
adult and spawning life stages, changes in the channel to create an
ecological park would produce a considerable loss of potentially
usable habitat (PUH), while in the case of the juvenile life stage PUH
remains virtually unchanged, and in the case of life stage fry the PUH
would increase due to the presence of velocities and depths of lesser
magnitude, due to the presence of minor flow rates and lower volume
of the wet channel.
It is expected that habitat modification for linear park construction
may produce the lack of Ictalurus punktatus species conservation at
the river reach of the study.
Abstract: A dip-coating process has been used to form an
asymmetric silica membrane with improved membrane performance
and reproducibility. First, we deposited repeatedly silica on top of a
commercial alumina membrane support to improve its structural
make up. The membrane is further processed under clean room
conditions to avoid dust impurity and subsequent drying in an oven
for high thermal, chemical and physical stability. The resulting
asymmetric membrane exhibits a gradual change in the membrane
layer thickness. Compared to the support, the dual-layer process
improves the gas flow rates. For the scientific applications for natural
gas purification, CO2, CH4 and H2 gas flow rates were. In addition,
the membrane selectively separated hydrogen.
Abstract: Water miscible cutting fluids are conventionally used to lubricate and cool the machining zone. But issues related to health hazards, maintenance and disposal costs have limited their usage, leading to application of Minimum Quantity Lubrication (MQL). To increase the effectiveness of MQL, nanocutting fluids are proposed. In the present work, water miscible nanographite cutting fluids of varying concentration are applied at cutting zone by two systems A and B. System A utilizes high pressure air and supplies cutting fluid at a flow rate of 1ml/min. System B uses low pressure air and supplies cutting fluid at a flow rate of 5ml/min. Their performance in machining is evaluated by measuring cutting temperatures, tool wear, cutting forces and surface roughness and compared with dry machining and flood machining. Application of nanocutting fluid using both systems showed better performance than dry machining. Cutting temperatures and cutting forces obtained by both techniques are more than flood machining. But tool wear and surface roughness showed improvement compared to flood machining. Economic analysis has been carried out in all the cases to decide the applicability of the techniques.
Abstract: In wastewater treatment processes, aeration introduces
air into a liquid. In these systems, air is introduced by different
devices submerged in the wastewater. Smaller bubbles result in more
bubble surface area per unit of volume and higher oxygen transfer
efficiency. Jet pumps are devices that use air bubbles and are widely
used in wastewater treatment processes. The principle of jet pumps is
their ability to transfer energy of one fluid, called primary or motive,
into a secondary fluid or gas. These pumps have no moving parts and
are able to work in remote areas under extreme conditions. The
objective of this work is to study experimentally the characteristics of
the jet pump and the size of air bubbles in the laboratory water tank.
The effect of flow rate ratio on pump performance is investigated in
order to have a better understanding about pump behavior under
various conditions, in order to determine the efficiency of receiving
air bubbles different sizes. The experiments show that we should take
care when increasing the flow rate ratio while seeking to decrease
bubble size in the outlet flow. This study will help improve and
extend the use of the jet pump in many practical applications.
Abstract: An unconventional composite inorganic ceramic
membrane capable of enhancing carbon dioxide emission decline was
fabricated and tested at laboratory scale in conformism to various
environmental guidelines and also to mitigate the effect of global
warming. A review of the existing membrane technologies for carbon
capture including the relevant gas transport mechanisms is presented.
Single gas permeation experiments using silica modified ceramic
membrane with internal diameter 20mm, outside diameter 25mm and
length of 368mm deposited on a macro porous support was carried
out to investigate individual gas permeation behaviours at different
pressures at room temperature. Membrane fabrication was achieved
using after a dip coating method. Nitrogen, Carbon dioxide, Argon,
Oxygen and Methane pure gases were used to investigate their
individual permeation rates at various pressures. Results show that
the gas flow rate increases with pressure drop. However above a
pressure of 3bar, CO2 permeability ratio to that of the other gases
indicated control of a more selective surface adsorptive transport
mechanism.
Abstract: Present study is carried out on six lane divided urban
arterial road in Patna and Pune city of India. Both the road having
distinct differences in terms of the vehicle composition and the road
side parking. Arterial road in Patan city has 33% of non-motorized
mode, whereas Pune arterial road dominated by 65% of Two wheeler.
Also road side parking is observed in Patna city. The field studies
using videography techniques are carried out for traffic data
collection. Data are extracted for one minute duration for vehicle
composition, speed variation and flow rate on selected arterial road of
the two cities. Speed flow relationship is developed and capacity is
determine. Equivalency factor in terms of dynamic car unit is
determine to represent the vehicle is single unit. The variation in the
capacity due to side friction, presence of non motorized traffic and
effective utilization of lane width is compared at concluding remarks.
Abstract: The present work attempts to investigate the
combustion, performance and emission characteristics of an existing
single-cylinder four-stroke compression-ignition engine operated in
dual-fuel mode with hydrogen as an alternative fuel. Environmental
concerns and limited amount of petroleum fuels have caused interests
in the development of alternative fuels like hydrogen for internal
combustion (IC) engines. In this experimental investigation, a diesel
engine is made to run using hydrogen in dual fuel mode with diesel,
where hydrogen is introduced into the intake manifold using an LPGCNG
injector and pilot diesel is injected using diesel injectors. A
Timed Manifold Injection (TMI) system has been developed to vary
the injection strategies. The optimized timing for the injection of
hydrogen was 10^0 CA after top dead center (ATDC). From the study
it was observed that with increasing hydrogen rate, enhancement in
brake thermal efficiency (BTHE) of the engine has been observed
with reduction in brake specific energy consumption (BSEC).
Furthermore, Soot contents decrease with an increase in indicated
specific NOx emissions with the enhancement of hydrogen flow rate.
Abstract: This paper presents a model for a modified T-junction
device for microspheres generation. The numerical model is
developed using a commercial software package: COMSOL
Multiphysics. In order to test the accuracy of the numerical model,
multiple variables, such as the flow rate of cross-flow, fluid properties,
structure, and geometry of the microdevice are applied. The results
from the model are compared with the experimental results in the
diameter of the microsphere generated. The comparison shows a good
agreement. Therefore the model is useful in further optimization of the
device and feedback control of microsphere generation if any.
Abstract: Incineration of municipal solid waste (MSW) is one of
the key scopes in the global clean energy strategy. A computational
fluid dynamics (CFD) model was established in order to reveal these
features of the combustion process in a fixed porous bed of MSW.
Transporting equations and process rate equations of the waste bed
were modeled and set up to describe the incineration process,
according to the local thermal conditions and waste property
characters. Gas phase turbulence was modeled using k-ε turbulent
model and the particle phase was modeled using the kinetic theory of
granular flow. The heterogeneous reaction rates were determined
using Arrhenius eddy dissipation and the Arrhenius-diffusion
reaction rates. The effects of primary air flow rate and temperature in
the burning process of simulated MSW are investigated
experimentally and numerically. The simulation results in bed are
accordant with experimental data well. The model provides detailed
information on burning processes in the fixed bed, which is otherwise
very difficult to obtain by conventional experimental techniques.
Abstract: Groundwater inflow to the tunnels is one of the most
important problems in tunneling operation. The objective of this
study is the investigation of model dimension effects on tunnel inflow
assessment in discontinuous rock masses using numerical modeling.
In the numerical simulation, the model dimension has an important
role in prediction of water inflow rate. When the model dimension is
very small, due to low distance to the tunnel border, the model
boundary conditions affect the estimated amount of groundwater flow
into the tunnel and results show a very high inflow to tunnel. Hence,
in this study, the two-dimensional universal distinct element code
(UDEC) used and the impact of different model parameters, such as
tunnel radius, joint spacing, horizontal and vertical model domain
extent has been evaluated. Results show that the model domain extent
is a function of the most significant parameters, which are tunnel
radius and joint spacing.
Abstract: Activated carbons (M4P0, M4P2, and M5P2) used in
this research were produced from palm shell and polyetherether
ketone (PEEK) via carbonization, impregnation and microwave
activation. The adsorption/desorption process was carried out using
static volumetric adsorption. Regeneration is important in the overall
economy of the process and waste minimization. This work focuses
on the thermal regeneration of the CO2 exhausted microwave
activated carbons. The regeneration strategy adopted was thermal
with nitrogen purge desorption with N2 feed flow rate of 20 ml/min
for 1 h at atmospheric pressure followed by drying at 150oC.Seven
successive adsorption/regeneration processes were carried out on the
material. It was found that after seven adsorption regeneration cycles;
the regeneration efficiency (RE) for CO2 activated carbon from palm
shell only (M4P0) was more than 90% while that of hybrid palm
shell-PEEK (M4P2, M5P2) was above 95%. The cyclic adsorption
and regeneration shows the stability of the adsorbent materials.
Abstract: Carbon Deposits are often occurred inside the
industrial coke oven during coking process. Accumulation of carbon
deposits may cause a big issue, which seriously influences the coking
operation. The carbon is burning off by injecting fresh air through
pipes into coke oven which is an efficient way practically operated in
industries. The burning off carbon deposition in coke oven performed
by Computational Fluid Dynamics (CFD) method has provided an
evaluation of the feasibility study. A three dimensional, transient,
turbulent reacting flow simulation has performed with three different
injecting air flow rate and another kind of injecting configuration. The
result shows that injection higher air flow rate would effectively
reduce the carbon deposits. In the meantime, the opened charging
holes would suck extra oxygen from atmosphere to participate in
reactions. In term of coke oven operating limits, the wall temperatures
are monitored to prevent over-heating of the adiabatic walls during
burn-off process.
Abstract: This paper presents the results and findings from a
parametric study on the water surface elevation at upstream of bridge
constriction for subcritical flow. In this study, the influence of
Manning's Roughness Coefficient of main channel (nmc) and
floodplain (nfp), and bridge opening (b) flow rate (Q), contraction
(kcon) and expansion coefficients (kexp) were investigated on
backwater level. The DECK bridge models with different span widths
and without any pier were investigated within the two stage channel
having various roughness conditions. One of the most commonly
used commercial one-dimensional HEC-RAS model was used in this
parametric study. This study showed that the effects of main channel
roughness (nmc) and flow rate (Q) on the backwater level are much
higher than those of the floodplain roughness (nfp). Bridge opening
(b) with contraction (kcon) and expansion coefficients (kexp) have very
little effect on the backwater level within this range of parameters.
Abstract: Organic Rankine Cycle (ORC) is the most commonly used method for recovering energy from small sources of heat. The investigation of the ORC in supercritical condition is a new research area as it has a potential to generate high power and thermal efficiency in a waste heat recovery system. This paper presents a steady state ORC model in supercritical condition and its simulations with a real engine’s exhaust data. The key component of ORC, evaporator, is modelled using finite volume method, modelling of all other components of the waste heat recovery system such as pump, expander and condenser are also presented. The aim of this paper is to investigate the effects of mass flow rate and evaporator outlet temperature on the efficiency of the waste heat recovery process. Additionally, the necessity of maintaining an optimum evaporator outlet temperature is also investigated. Simulation results show that modification of mass flow rate is the key to changing the operating temperature at the evaporator outlet.
Abstract: Macro invertebrates have been used to monitor
organic pollution in rivers and streams. Several biotic indices based
on macro invertebrates have been developed over the years including
the Biological Monitoring Working Party (BMWP). A new biotic
index, the Gammarus:Asellus ratio has been recently proposed as an
index of organic pollution. This study tested the validity of the
Gammarus:Asellus ratio as an index of organic pollution, by
examining the relationship between the Gammarus:Asellus ratio and
physical chemical parameters, and other biotic indices such as
BMWP and, Average Score Per Taxon (ASPT) from lakes and
streams at Markeaton Park, Allestree Park and Kedleston Hall,
Derbyshire. Macro invertebrates were sampled using the standard
five minute kick sampling techniques physical and chemical
environmental variables were obtained based on standard sampling
techniques. Eighteen sites were sampled, six sites from Markeaton
Park (three sites across the stream and three sites across the lake). Six
sites each were also sampled from Allestree Park and Kedleston Hall
lakes. The Gammarus:Asellus ratio showed an opposite significant
positive correlations with parameters indicative of organic pollution
such as the level of nitrates, phosphates, and calcium and also
revealed a negatively significant correlations with other biotic indices
(BMWP/ASPT). The BMWP score correlated positively significantly
with some water quality parameters such as dissolved oxygen and
flow rate, but revealed no correlations with other chemical
environmental variables. The BMWP score was significantly higher
in the stream than the lake in Markeaton Park, also The ASPT scores
appear to be significantly higher in the upper Lakes than the middle
and lower lakes. This study has further strengthened the use of
BMWP/ASPT score as an index of organic pollution. But additional
application is required to validate the use of Gammarus:Asellus as a
rapid bio monitoring tool.
Abstract: Diffusion stills have been effective in water
desalination. The present work represents a model of the distillation
process by using vertical single-effect diffusion stills. A semianalytical
model has been developed to model the process. A
software computer code using Engineering Equation Solver EES
software has been developed to solve the equations of the developed
model. An experimental setup has been constructed, and used for the
validation of the model. The model is also validated against former
literature results. The results obtained from the present experimental
test rig, and the data from the literature, have been compared with the
results of the code to find its best range of validity. In addition, a
parametric analysis of the system has been developed using the
model to determine the effect of operating conditions on the system's
performance. The dominant parameters that affect the productivity of
the still are the hot plate temperature that ranges from (55- 90°C) and
feed flow rate in range of (0.00694-0.0211 kg/m2-s).
Abstract: The 6th version of Universal modeling method for
centrifugal compressor stage calculation is described. Identification
of the new mathematical model was made. As a result of
identification the uniform set of empirical coefficients is received.
The efficiency definition error is 0,86 % at a design point. The
efficiency definition error at five flow rate points (except a point of
the maximum flow rate) is 1,22 %. Several variants of the stage with
3D impellers designed by 6th version program and quasi threedimensional
calculation programs were compared by their gas
dynamic performances CFD (NUMECA FINE TURBO).
Performance comparison demonstrated general principles of design
validity and leads to some design recommendations.
Abstract: Universal modeling method well proven for industrial
compressors was applied for design of the high flow rate supersonic
stage. Results were checked by ANSYS CFX and NUMECA Fine
Turbo calculations. The impeller appeared to be very effective at
transonic flow velocities. Stator elements efficiency is acceptable at
design Mach numbers too. Their loss coefficient versus inlet flow
angle performances correlates well with Universal modeling
prediction. The impeller demonstrates ability of satisfactory operation
at design flow rate. Supersonic flow behavior in the impeller inducer
at the shroud blade to blade surface Φ des deserves additional study.
Abstract: There is an evident trend to elevate pressure ratio of a
single stage of a turbo compressors - axial compressors in particular.
Whilst there was an opinion recently that a pressure ratio 1,9 was a
reasonable limit, later appeared information on successful modeling
tested of stages with pressure ratio up to 2,8. The authors recon that
lack of information on high pressure stages makes actual a study of
rational choice of design parameters before high supersonic flow
problems solving. The computer program of an engineering type was
developed. Below is presented a sample of its application to study
possible parameters of the impeller of the stage with pressure ratio
3,0. Influence of two main design parameters on expected efficiency,
periphery blade speed and flow structure is demonstrated. The results
had lead to choose a variant for further analysis and improvement by
CFD methods.