Abstract: Over the last decades, worldwide environmental awareness has grown due to the depletion of raw material resources and global warming. This awareness has prompted the development of new products more environmentally friendly. Among these products are biocomposite materials reinforced with natural fibers. The main challenge in developing the use of biocomposites in exterior applications is the lack of knowledge about their durability and the evolution of their mechanical and physicochemical properties in the long term. The aim of this work is to study the photooxidation of unidirectional (UD) composites based on recycled matrix. For this purpose, UD flax fiber composites based on recycled polypropylene were prepared by thermocompression. An accelerated aging test was carried out using a xenon arc WeatherOmeter. The consequences of UV exposure on the chemical composition and morphology of the surface of composites as well as on their tensile mechanical properties have been reported. The results showed that accelerated aging had a significant effect on the surface of these composites while it had little impact on their mechanical properties.
Abstract: Interest in natural fiber-reinforced composites (NFRC) is progressively growing both in terms of academia research and industrial applications thanks to their abundant advantages such as low cost, biodegradability, eco-friendly nature and relatively good mechanical properties. However, their widespread use is still presumed as challenging because of the specificity of their non-homogeneous structure, limited knowledge on their machinability characteristics and parameter settings, to avoid defects associated with the machining process. The present work is aimed to investigate the effect of the cutting tool geometry and material on the drilling-induced delamination, thrust force and hole quality produced when drilling a fully biodegradable flax/poly (lactic acid) composite laminate. Three drills with different geometries and material were used at different drilling conditions to evaluate the machinability of the fabricated composites. The experimental results indicated that the choice of cutting tool, in terms of material and geometry, has a noticeable influence on the cutting thrust force and subsequently drilling-induced damages. The lower value of thrust force and better hole quality was observed using high-speed steel (HSS) drill, whereas Carbide drill (with point angle of 130o) resulted in the highest value of thrust force. Carbide drill presented higher wear resistance and stability in variation of thrust force with a number of holes drilled, while HSS drill showed the lower value of thrust force during the drilling process. Finally, within the selected cutting range, the delamination damage increased noticeably with feed rate and moderately with spindle speed.
Abstract: Alkyds have become essential raw materials in the coating and paint industry, due to their low cost, good application properties and lower environmental impact in comparison with petroleum-based polymers. The properties of these oil-modified materials depend on the type of polyunsaturated vegetable oil used for its manufacturing, since a higher degree of unsaturation provides a better crosslinking of the cured paint. Linum usitatissimum L. (flax) oil is widely used to develop alkyd resins due to its high degree of unsaturation. Although it is intended to find non-traditional sources and increase their commercial value, to authors’ best knowledge a natural source that can replace flaxseed oil has not yet been found. However, Plukenetia volubilis L. oil, of Peruvian origin, contains a similar fatty acid polyunsaturated content to the one reported for Linum usitatissimum L. oil. In this perspective, medium alkyd resins were prepared with a mixture of 50% of Linum usitatissimum L. oil and 50% of Plukenetia volubilis L. oil. Pure Linum usitatissimum L. oil was also used for comparison purposes. Three different resins were obtained by varying the amount of glycerol and pentaerythritol. The synthesized alkyd resins were characterized by FT-IR, and physicochemical properties like acid value, colour, viscosity, density and drying time were evaluated by standard methods. The pencil hardness and chemical resistance behaviour of the cured resins were also studied. Overall, it can be concluded that medium alkyd resins containing Plukenetia volubilis L. oil have an equivalent behaviour compared to those prepared purely with Linum usitatissimum L. oil. Both Plukenetia volubilis L. oil and pentaerythritol have a remarkable influence on certain physicochemical properties of medium alkyd resins.
Abstract: Iron oxide nanoparticles (Fe2O3NPs) are widely used in different applications due to its ecofriendly nature and biocompatibility. Hence, in this investigation, biosynthesized Fe2O3NPs influence on flax (Linum usitatissimum L.) plant was examined. The biosynthesized nanoparticles were found to be cubic phase which is confirmed by XRD analysis. FTIR analysis confirmed the presence of functional groups corresponding to the iron oxide nanoparticle. The elemental analysis also confirmed that the obtained nanoparticle is iron oxide nanoparticle. The scanning electron microscopy and the transmission electron microscopy confirm that the average particle size was around 56 nm. The effect of Fe2O3NPs on seed germination followed by biochemical analysis was carried out using standard methods. The results obtained after four days and 11 days of seed vigor studies showed that the seedling length (cm), average number of seedling with leaves, increase in root length (cm) was found to be enhanced on treatment with iron oxide nanoparticles when compared to control. A positive correlation was noticed with the dose of the nanoparticle and plant growth, which may be due to changes in metabolic activity. Hence, to evaluate the change in metabolic activity, peroxidase and catalase activities were estimated. It was clear from the observation that higher concentration of iron oxide nanoparticles (Fe2O3NPs 1000 mg/L) has enhanced peroxidase and catalase activities and in turn plant growth. Thus, this study clearly showed that biosynthesized iron oxide nanoparticles will be an effective nano-nutrient for agriculture applications.
Abstract: Biocomposites is a field that has gained much scientific attention due to the current substantial consumption of non-renewable resources and the environmentally harmful disposal methods required for traditional polymer composites. Research on natural fiber reinforced polyhydroxyalkanoates (PHAs) has gained considerable momentum over the past decade. There is little work on PHAs reinforced with unidirectional (UD) natural fibers and little work on using epoxidized natural rubber (ENR) as a toughening agent for PHA-based biocomposites. In this work, we prepared polyhydroxybutyrate-co-valerate (PHBV) biocomposites reinforced with UD 30 wt.% flax fibers and evaluated the use of ENR with 50% epoxidation (ENR50) as a toughening agent for PHBV biocomposites. Quasi-unidirectional flax/PHBV composites were prepared by hand layup, powder impregnation followed by compression molding. Toughening agents – polybutylene adiphate-co-terephthalate (PBAT) and ENR50 – were cryogenically ground into powder and mechanically mixed with main matrix PHBV to maintain the powder impregnation process. The tensile, flexural and impact properties of the biocomposites were measured and morphology of the composites examined using optical microscopy (OM) and scanning electron microscopy (SEM). The UD biocomposites showed exceptionally high mechanical properties as compared to the results obtained previously where only short fibers have been used. The improved tensile and flexural properties were attributed to the continuous nature of the fiber reinforcement and the increased proportion of fibers in the loading direction. The improved impact properties were attributed to a larger surface area for fiber-matrix debonding and for subsequent sliding and fiber pull-out mechanisms to act on, allowing more energy to be absorbed. Coating cryogenically ground ENR50 particles with PHBV powder successfully inhibits the self-healing nature of ENR-50, preventing particles from coalescing and overcoming problems in mechanical mixing, compounding and molding. Cryogenic grinding, followed by powder impregnation and subsequent compression molding is an effective route to the production of high-mechanical-property biocomposites based on renewable resources for high-obsolescence applications such as plastic casings for consumer electronics.
Abstract: Geopolymer composites reinforced with flax fabrics
and nanoclay are fabricated and studied for physical and mechanical
properties using X-Ray Diffraction (XRD), Fourier Transform
Infrared Spectroscopy (FTIR), and Scanning Electron Microscope
(SEM). Nanoclay platelets at a weight of 1.0%, 2.0%, and 3.0% were
added to geopolymer pastes. Nanoclay at 2.0 wt.% was found to
improve density and decrease porosity while improving flexural
strength and post-peak toughness. A microstructural analysis
indicated that nanoclay behaves as filler and as an activator
supporting geopolymeric reaction while producing a higher content
geopolymer gel improving the microstructure of binders. The process
enhances adhesion between the geopolymer matrix and flax fibres.
Abstract: Work presented is interested in the characterization of
the quasistatic mechanical properties and in fatigue of a composite
laminated in jute/epoxy. The natural fibers offer promising prospects
thanks to their interesting specific properties, because of their low
density, but also with their bio-deterioration. Several scientific
studies highlighted the good mechanical resistance of the vegetable
fiber composites reinforced, even after several recycling. Because of
the environmental standards that become increasingly severe, one
attends the emergence of eco-materials at the base of natural fibers
such as flax, bamboo, hemp, sisal, jute. The fatigue tests on
elementary vegetable fibers show an increase of about 60% of the
rigidity of elementary fibers of hemp subjected to cyclic loadings. In
this study, the test-tubes manufactured by the method infusion have
sequences of stacking of 0/90° and ± 45° for the shearing and tensile
tests. The quasistatic tests reveal a variability of the mechanical
properties of about 8%. The tensile fatigue tests were carried out for
levels of constraints equivalent to half of the ultimate values of the
composite. Once the fatigue tests carried out for well-defined values
of cycles, a series of static tests of traction type highlights the
influence of the number of cycles on the quasi-static mechanical
behavior of the laminate jute/epoxy.
Abstract: Crops diversity and maintaining and enhancing the
fertility of agricultural lands are basic principles of organic farming.
With a wider range of crops in agroecosystem can improve the ability
to control weeds, pests and diseases, and the performance of crops
rotation and food safety. In this sense, the main objective of the
research was to study the productivity and chemical composition of
some alternative crops and their adaptability to soil and climatic
conditions of the agricultural area in Southern Romania and to
cultivation in the organic farming system. The alternative crops were:
lentil (7 genotypes); five species of grain legumes (5 genotypes); four
species of oil crops (5 genotypes). The seed production was, on
average: 1343 kg/ha of lentil; 2500 kg/ha of field beans; 2400 kg/ha
of chick peas and blackeyed peas; more than 2000 kg/ha of atzuki
beans, over 1250 kg/ha of fenugreek; 2200 kg/ha of safflower; 570
kg/ha of oil pumpkin; 2150 kg/ha of oil flax; 1518 kg/ha of camelina.
Regarding chemical composition, lentil seeds contained: 22.18%
proteins, 3.03% lipids, 33.29% glucides, 4.00% minerals, and 259.97
kcal energy values. For field beans: 21.50% proteins, 4.40% lipids,
63.90% glucides, 5.85% minerals, 395.36 kcal energetic value. For
chick peas: 21.23% proteins, 4.55% lipids, 53.00% glucides, 3.67%
minerals, 348.22 kcal energetic value. For blackeyed peas: 23.30%
proteins, 2.10% lipids, 68.10% glucides, 3.93% minerals, 350.14 kcal
energetic value. For adzuki beans: 21.90% proteins, 2.60% lipids,
69.30% glucides, 4.10% minerals, 402.48 kcal energetic value. For
fenugreek: 21.30% proteins, 4.65% lipids, 63.83% glucides, 5.69%
minerals, 396.54 kcal energetic value. For safflower: 12.60%
proteins, 28.37% lipids, 46.41% glucides, 3.60% minerals, 505.78
kcal energetic value. For camelina: 20.29% proteins, 31.68% lipids,
36.28% glucides, 4.29% minerals, 526.63 kcal energetic value. For
oil pumpkin: 29.50% proteins, 36.92% lipids, 18.50% glucides,
5.41% minerals, 540.15 kcal energetic value. For oil flax: 22.56%
proteins, 34.10% lipids, 27.73% glucides, 5.25% minerals, 558.45
kcal energetic value.
Abstract: The majority of contemporary insulation materials
commonly used in the building industry is made from non-renewable
raw materials; furthermore, their production often brings high energy
costs. A long-term trend as far as sustainable development is
concerned has been the reduction of energy and material demands of
building material production. One of the solutions is the possibility of
using easily renewable natural raw material sources which are
considerably more ecological and their production is mostly less
energy-consuming compared to the production of normal insulations
(mineral wool, polystyrene). The paper describes the results of
research focused on the development of thermal and acoustic
insulation materials based on natural fibres intended for floor
constructions. Given the characteristic open porosity of natural fibre
materials, the hygrothermal behaviour of the developed materials was
studied. Especially the influence of relative humidity and temperature
on thermal insulation properties was observed.
Abstract: The aim of the current research was to investigate the
gassy ozone effect on quality parameters of flaxes made form whole
biologically activated wheat grains. The research was accomplished
on wheat grains variety
Abstract: Evaluation of crop plants resistance to environmental
stresses specially in germination stage is a critical factor in their
selection in different conditions of cultivation. Therefore use of a
procedure in controllable situation can help to evaluate plants
reaction to stress quickly and precisely. In order to study germination
characteristics of flax in water and salinity stress conditions were
conducted two laboratories experimental. The two experimental were
conducted in 4-replicant completing random design for salinity and
water stress. The treatment, for salinity and water stress was three
potential (zero, 40, 80 mM) of NaCl and three potential (zero, -2, -4
bar) of PEG respectively. Germination percentage and rate, in
addition to Radical and plumule length and dry-weight and
plumule/Radical ration were measured. All of characteristics reduce
under water stress conditions. salinity stress significant reduce
germination rate and Radical and plumule length of flax seeds.
Hydropriming and osmopriming significant increased germination
rate, plumule length and plumule/Radical ration ration of flax seeds.
But germination percentage and Radical and plumule dry weight
significant increased only in hydropriming treat. Hydropriming and
osmopriming could not be used to improved germination under saline
and drought stress. But has more tolerance in salinity and drought
stress in flax by less reduce in Radical and plumule length under
saline and drought stress.
Abstract: Renewable natural fibres such as oil palm, flax, and
pineapple leaf can be utilized to obtain new high performance
polymer materials. The reuse of waste natural fibres as reinforcement
for polymer is a sustainable option to the environment. However, due
to its high hydroxyl content of cellulose, natural fibres are
susceptible to absorb water that affects the composite mechanical
properties adversely. Research found that Nano materials such as
Nano Silica Carbide (n-SiC) and Nano Clay can be added into the
polymer composite to overcome this problem by enhancing its
mechanical properties in wet condition. The addition of Nano
material improves the tensile and wear properties, flexural stressstrain
behaviour, fracture toughness, and fracture strength of polymer
natural composites in wet and dry conditions.