Abstract: Computational simulation of steam flow and heat transfer in power plant condensers on the basis of the threedimensional mathematical model for the flow through porous media is presented. In order to solve the mathematical model of steam flow and heat transfer in power plant condensers, the Streamline Upwind Petrov-Galerkin finite element method is applied. By comparison of the results of simulation with experimental results about an experimental condenser, it is confirmed that SUPG finite element method can be successfully applied for solving the three-dimensional mathematical model of steam flow and heat transfer in power plant condensers.
Abstract: The electrical interaction between two axisymmetric
spheroidal particles in an electrolyte solution is examined numerically.
A Galerkin finite element method combined with a Newton-Raphson
iteration scheme is proposed to evaluate the spatial variation in the
electrical potential, and the result obtained used to estimate the
interaction energy between two particles. We show that if the surface
charge density is fixed, the potential gradient is larger at a point, which
has a larger curvature, and if surface potential is fixed, surface charge
density is proportional to the curvature. Also, if the total interaction
energy against closest surface-to-surface curve exhibits a primary
maximum, the maximum follows the order (oblate-oblate) >
(sphere-sphere)>(oblate-prolate)>(prolate-prolate), and if the curve
has a secondary minimum, the absolute value of the minimum follows
the same order.
Abstract: In this paper, the dam-reservoir interaction is
analyzed using a finite element approach. The fluid is assumed to be
incompressible, irrotational and inviscid. The assumed boundary
conditions are that the interface of the dam and reservoir is vertical
and the bottom of reservoir is rigid and horizontal. The governing
equation for these boundary conditions is implemented in the
developed finite element code considering the horizontal and vertical
earthquake components. The weighted residual standard Galerkin
finite element technique with 8-node elements is used to discretize
the equation that produces a symmetric matrix equation for the damreservoir
system. A new boundary condition is proposed for
truncating surface of unbounded fluid domain to show the energy
dissipation in the reservoir, through radiation in the infinite upstream
direction. The Sommerfeld-s and perfect damping boundary
conditions are also implemented for a truncated boundary to compare
with the proposed far end boundary. The results are compared with
an analytical solution to demonstrate the accuracy of the proposed
formulation and other truncated boundary conditions in modeling the
hydrodynamic response of an infinite reservoir.
Abstract: In this paper fatigue crack initiation and propagation in notched plate under constant amplitude loading through tensile residual stress field of 2024 T351 Al-alloy plate were investigated. Residual stress field was generated by plastic deformation using finite element method (FEM) where isotropic hardening in Von Mises model was applied. Simulation of fatigue behavior was made on AFGROW code. It was shown that the fatigue crack initiation and propagation were affected by level of residual stress filed. In this investigation, the presence of tensile residual stresses at notch (hole) reduces considerably the total fatigue life. It was shown that the decreasing in stress reduces the fatigue crack growth rates.
Abstract: Over the course of the past century, the global
automotive industry-s stance towards safety has evolved from one of
contempt to one nearing reverence. A suspension system that
provides safe handling and cornering capabilities can, with the help
of an efficient braking system, improve safety to a large extent. The
aim of this research is to propose a new automotive brake rotor
design and to compare it with automotive vented disk rotor. Static
structural and transient thermal analysis have been carried out on the
vented disk rotor and proposed rotor designs to evaluate and compare
their performance. Finite element analysis was employed for both
static structural and transient thermal analysis. Structural analysis
was carried out to study the stress and deformation pattern of the
rotors under extreme loads. Time varying temperature load was
applied on the rotors and the temperature distribution was analysed
considering cooling parameters (convection and radiation). This
dissertation illustrates the use of Finite Element Methods to examine
models, concluding with a comparative study of the proposed rotor
design and the conventional vented disk rotor for structural stability
and thermal efficiency.
Abstract: For investigations of electromagnetic field
distributions in biological structures by Finite Element Method
(FEM), a method for automatic 3D model building of human
anatomical objects is developed. Models are made by meshed
structures and specific electromagnetic material properties for each
tissue type. Mesh is built according to specific FEM criteria for
achieving good solution accuracy. Several FEM models of
anatomical objects are built. Formulation using magnetic vector
potential and scalar electric potential (A-V, A) is used for modeling
of electromagnetic fields in human tissue objects. The developed
models are suitable for investigations of electromagnetic field
distributions in human tissues exposed in external fields during
magnetic stimulation, defibrillation, impedance tomography etc.
Abstract: As application of re-activation of backside on power
device Insulated Gate Bipolar Transistor (IGBT), laser annealing was
employed to irradiate amorphous silicon substrate, and resistivities
were measured using four point probe measurement. For annealing
the amorphous silicon two lasers were used at wavelength of visible
green (532 nm) together with Infrared (793 nm). While the green
laser efficiently increased temperature at top surface the Infrared
laser reached more deep inside and was effective for melting the
top surface. A finite element method was employed to evaluate time
dependent thermal distribution in silicon substrate.
Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetical and thermal stresses remain major failures for
insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: In this study, a vibration analysis was carried out of
symmetric angle-ply laminated composite plates with and without
square hole when subjected to compressive loads, numerically. A
buckling analysis is also performed to determine the buckling load of
laminated plates. For each fibre orientation, the compression load is
taken equal to 50% of the corresponding buckling load. In the
analysis, finite element method (FEM) was applied to perform
parametric studies, the effects of degree of orthotropy and stacking
sequence upon the fundamental frequencies and buckling loads are
discussed. The results show that the presence of a constant
compressive load tends to reduce uniformly the natural frequencies
for materials which have a low degree of orthotropy. However, this
reduction becomes non-uniform for materials with a higher degree of
orthotropy.
Abstract: In this study, the hydrogen transport phenomenon was
numerically evaluated by using hydrogen-enhanced localized
plasticity (HELP) mechanisms. Two dominant governing equations,
namely, the hydrogen transport model and the elasto-plastic model,
were introduced. In addition, the implicitly formulated equations of
the governing equations were implemented into ABAQUS UMAT
user-defined subroutines. The simulation results were compared to
published results to validate the proposed method.
Abstract: Cylindrical concrete reservoirs are appropriate choice
for storing liquids as water, oil and etc. By using of the pre-cast
concrete reservoirs instead of the in-situ constructed reservoirs, the
speed and precision of the construction would considerably increase.
In this construction method, wall and roof panels would make in
factory with high quality materials and precise controlling. Then,
pre-cast wall and roof panels would carry out to the construction site
for assembling. This method has a few faults such as: the existing
weeks in connection of wall panels together and wall panels to
foundation. Therefore, these have to be resisted under applied loads
such as seismic load. One of the innovative methods which was
successfully applied for seismic retrofitting of numerous pre-cast
cylindrical water reservoirs in New Zealand, using of the high tensile
cables around the reservoirs and post-tensioning them. In this paper,
analytical modeling of wall and roof panels and post-tensioned
cables are carried out with finite element method and the effect of
height to diameter ratio, post-tensioning force value, liquid level in
reservoir, installing position of tendons on seismic response of
reservoirs are investigated.
Abstract: In this article, an adaptive least-squares mixed finite element method is studied for pseudo-parabolic integro-differential equations. The solutions of least-squares mixed weak formulation and mixed finite element are proved. A posteriori error estimator is constructed based on the least-squares functional and the posteriori errors are obtained.
Abstract: The purpose of this study is to derive optimal shapes of
a body located in viscous flows by the finite element method using the
acoustic velocity and the four-step explicit scheme. The formulation
is based on an optimal control theory in which a performance function
of the fluid force is introduced. The performance function should be
minimized satisfying the state equation. This problem can be transformed
into the minimization problem without constraint conditions
by using the adjoint equation with adjoint variables corresponding to
the state equation. The performance function is defined by the drag
and lift forces acting on the body. The weighted gradient method
is applied as a minimization technique, the Galerkin finite element
method is used as a spatial discretization and the four-step explicit
scheme is used as a temporal discretization to solve the state equation
and the adjoint equation. As the interpolation, the orthogonal basis
bubble function for velocity and the linear function for pressure
are employed. In case that the orthogonal basis bubble function is
used, the mass matrix can be diagonalized without any artificial
centralization. The shape optimization is performed by the presented
method.
Abstract: In this paper, a thermal model of cast- resin dry type
transformer is proposed. The proposed thermal model is solved by
finite element technique to get the temperature at any location of the
transformer. The basic modes of heat transfer such as conduction;
convection and radiation are used to get the steady state temperature
distribution of the transformer. The predicted temperatures are
compared with experimental results reported in this paper and it is
found a good agreement between them. The effects of various
parameters such as width of air duct, ambient temperature and
emissivity of the outer surface were also studied.
Abstract: Today, Hydroforming technology provides an
attractive alternative to conventional matched die forming, especially
for cost-sensitive, lower volume production, and for parts with
irregular contours. In this study the critical fluid pressures which lead
to rupture in the workpiece has been investigated by theoretical and
finite element methods. The axisymmetric analysis was developed to
investigate the tearing phenomenon in cylindrical Hydroforming
Deep Drawing (HDD). By use of obtained equations the effect of
anisotropy, drawing ratio, sheet thickness and strain hardening
exponent on tearing diagram were investigated.
Abstract: The seismic response of steel shear wall system considering nonlinearity effects using finite element method is investigated in this paper. The non-linear finite element analysis has potential as usable and reliable means for analyzing of civil structures with the availability of computer technology. In this research the large displacements and materially nonlinear behavior of shear wall is presented with developing of finite element code. A numerical model based on the finite element method for the seismic analysis of shear wall is presented with developing of finite element code in this research. To develop the finite element code, the standard Galerkin weighted residual formulation is used. Two-dimensional plane stress model and total Lagrangian formulation was carried out to present the shear wall response and the Newton-Raphson method is applied for the solution of nonlinear transient equations. The presented model in this paper can be developed for analysis of civil engineering structures with different material behavior and complicated geometry.
Abstract: The plastic forming process of sheet plate takes an
important place in forming metals. The traditional techniques of tool
design for sheet forming operations used in industry are experimental
and expensive methods. Prediction of the forming results,
determination of the punching force, blank holder forces and the
thickness distribution of the sheet metal will decrease the production
cost and time of the material to be formed. In this paper, multi-stage
deep drawing simulation of an Industrial Part has been presented
with finite element method. The entire production steps with
additional operations such as intermediate annealing and springback
has been simulated by ABAQUS software under axisymmetric
conditions. The simulation results such as sheet thickness
distribution, Punch force and residual stresses have been extracted in
any stages and sheet thickness distribution was compared with
experimental results. It was found through comparison of results, the
FE model have proven to be in close agreement with those of
experiment.
Abstract: The cable tower of Liede Bridge is a double-column curved-lever arched-beam portal framed structure. Being novel and unique in structure, its cable tower differs in complexity from traditional ones. This paper analyzes the ultimate load capacity of cable tower by adopting the finite element calculations and model tests which indicate that constitutive relations applied here give a better simulation of actual failure process of prestressed reinforced concrete. In vertical load, horizontal load and overloading tests, the stepped loading of the tower model is of linear relationship, and the test data has good repeatability. All suggests that the cable tower has good bearing capacity, rational design and high emergency capacity.
Abstract: Having considered tactile sensing and palpation of a
surgeon in order to detect kidney stone during open surgery; we
present the 2D model of nephrolithiasis (two dimensional model of
kidney containing a simulated stone). The effects of stone existence
that appear on the surface of kidney (because of exerting mechanical
load) are determined. Using Finite element method, it is illustrated
that the created stress patterns on the surface of kidney and stress
graphs not only show existence of stone inside kidney, but also show
its exact location.
Abstract: Manufacturing components of fiber-reinforced
thermoplastics requires three steps: heating the matrix, forming and
consolidation of the composite and terminal cooling the matrix. For
the heating process a pre-determined temperature distribution through
the layers and the thickness of the pre-consolidated sheets is
recommended to enable forming mechanism. Thus, a design for the
heating process for forming composites with thermoplastic matrices
is necessary. To obtain a constant temperature through thickness and
width of the sheet, the heating process was analyzed by the help of
the finite element method. The simulation models were validated by
experiments with resistance thermometers as well as with an infrared
camera. Based on the finite element simulation, heating methods for
infrared radiators have been developed. Using the numeric
simulation many iteration loops are required to determine the process
parameters. Hence, the initiation of a model for calculating relevant
process parameters started applying regression functions.