Abstract: In this paper, modeling of an acoustic enclosed
vehicle cabin has been carried out by using boundary element
method. Also, the second purpose of this study is analyzing of linear
wave equation in an acoustic field. The resultants of this modeling
consist of natural frequencies that have been compared with
resultants derived from finite element method. By using numerical
method (boundary element method) and after solution of wave
equation inside an acoustic enclosed cabin, this method has been
progressed to simulate noise inside a simple vehicle cabin.
Abstract: To enhance installation security, a LNG storage in Rudong of Jiangsu province was adopted as a practical work, and it was analyzed by nonlinear finite element method to research overall and local stability performance, as well as the stress and deformation under the action of wind load and self-weight. Results indicate that deformation is tiny when steel mesh maintains as an overall ring, and stress caused by vertical bending moment and tension of bottom tie wire are also in the safe range. However, axial forces of lap reinforcement in adjacent steel mesh exceed the ultimate bearing capacity of tie wire. Hence, tie wires are ruptured; single mesh loses lateral connection and turns into monolithic status as the destruction of overall structure. Further more, monolithic steel mesh is led to collapse by the damage of bottom connection. So, in order to prevent connection failure and enhance installation security, the overlapping parts of steel mesh should be taken more reliable measures.
Abstract: Behavior of dams against the seismic loads has been
studied by many researchers. Most of them proposed new numerical
methods to investigate the dam safety. In this paper, to study the
effect of nonlinear parameters of concrete in gravity dams, a twodimensional
approach was used including the finite element method,
staggered method and smeared crack approach. Effective parameters
in the models are physical properties of concrete such as modulus of
elasticity, tensile strength and specific fracture energy. Two different
models were used in foundation (mass-less and massed) in order to
determine the seismic response of concrete gravity dams. Results
show that when the nonlinear analysis includes the dam- foundation
interaction, the foundation-s mass, flexibility and radiation damping
are important in gravity dam-s response.
Abstract: The characterization and modeling of the dynamic
behavior of many built-up structures under vibration conditions is still
a subject of current research. The present study emphasizes the
theoretical investigation of slip damping in layered and jointed
welded cantilever structures using finite element approach.
Application of finite element method in damping analysis is relatively
recent, as such, some problems particularly slip damping analysis has
not received enough attention. To validate the finite element model
developed, experiments have been conducted on a number of mild
steel specimens under different initial conditions of vibration. Finite
element model developed affirms that the damping capacity of such
structures is influenced by a number of vital parameters such as;
pressure distribution, kinematic coefficient of friction and micro-slip
at the interfaces, amplitude, frequency of vibration, length and
thickness of the specimen. Finite element model developed can be
utilized effectively in the design of machine tools, automobiles,
aerodynamic and space structures, frames and machine members for
enhancing their damping capacity.
Abstract: In this paper, we study the pulsatile flow of blood through stenotic arteries. The inner layer of arterial walls is modeled as a porous medium and human blood is assumed as an incompressible fluid. A numerical algorithm based on the finite element method is developed to simulate the blood flow through both the lumen region and the porous wall. The algorithm is then applied to study the flow behaviour and to investigate the significance of the non-Newtonian effect.
Abstract: Headphones and earphones have many extremely small
holes or narrow slits; they use sound-absorbing or porous material (i.e.,
dampers) to suppress vibratory system resonance. The air viscosity in
these acoustic paths greatly affects the acoustic properties. Simulation
analyses such as the finite element method (FEM) therefore require
knowledge of the material properties of sound-absorbing or porous
materials, such as the characteristic impedance and propagation
constant. The transfer function method using acoustic tubes is a widely
known measuring method, but there is no literature on taking
measurements up to the audible range. To measure the acoustic
properties at high-range frequencies, the acoustic tubes that form the
measuring device need to be narrowed, and the distance between the
two microphones needs to be reduced. However, when the tubes are
narrowed, the characteristic impedance drops below the air impedance.
In this study, we considered the effect of air viscosity in an acoustical
tube, introduced a theoretical formula for this effect in the form of
complex density and complex sonic velocity, and verified the
theoretical formula. We also conducted an experiment and observed
the effect from air viscosity in the actual measurements.
Abstract: This paper features the modeling and design of a
Robust Decentralized Fast Output Sampling (RDFOS) Feedback
control technique for the active vibration control of a smart flexible
multimodel Euler-Bernoulli cantilever beams for a multivariable
(MIMO) case by retaining the first 6 vibratory modes. The beam
structure is modeled in state space form using the concept of
piezoelectric theory, the Euler-Bernoulli beam theory and the Finite
Element Method (FEM) technique by dividing the beam into 4 finite
elements and placing the piezoelectric sensor / actuator at two finite
element locations (positions 2 and 4) as collocated pairs, i.e., as
surface mounted sensor / actuator, thus giving rise to a multivariable
model of the smart structure plant with two inputs and two outputs.
Five such multivariable models are obtained by varying the
dimensions (aspect ratios) of the aluminium beam. Using model
order reduction technique, the reduced order model of the higher
order system is obtained based on dominant Eigen value retention
and the Davison technique. RDFOS feedback controllers are
designed for the above 5 multivariable-multimodel plant. The closed
loop responses with the RDFOS feedback gain and the magnitudes of
the control input are obtained and the performance of the proposed
multimodel smart structure system is evaluated for vibration control.
Abstract: This paper deals with a high-order accurate Runge
Kutta Discontinuous Galerkin (RKDG) method for the numerical
solution of the wave equation, which is one of the simple case of a
linear hyperbolic partial differential equation. Nodal DG method is
used for a finite element space discretization in 'x' by discontinuous
approximations. This method combines mainly two key ideas which
are based on the finite volume and finite element methods. The
physics of wave propagation being accounted for by means of
Riemann problems and accuracy is obtained by means of high-order
polynomial approximations within the elements. High order accurate
Low Storage Explicit Runge Kutta (LSERK) method is used for
temporal discretization in 't' that allows the method to be nonlinearly
stable regardless of its accuracy. The resulting RKDG
methods are stable and high-order accurate. The L1 ,L2 and L∞ error
norm analysis shows that the scheme is highly accurate and effective.
Hence, the method is well suited to achieve high order accurate
solution for the scalar wave equation and other hyperbolic equations.
Abstract: This paper deals with the design of a periodic output
feedback controller for a flexible beam structure modeled with
Timoshenko beam theory, Finite Element Method, State space
methods and embedded piezoelectrics concept. The first 3 modes are
considered in modeling the beam. The main objective of this work is
to control the vibrations of the beam when subjected to an external
force. Shear piezoelectric sensors and actuators are embedded into
the top and bottom layers of a flexible aluminum beam structure, thus
making it intelligent and self-adaptive. The composite beam is
divided into 5 finite elements and the control actuator is placed at
finite element position 1, whereas the sensor is varied from position 2
to 5, i.e., from the nearby fixed end to the free end. 4 state space
SISO models are thus developed. Periodic Output Feedback (POF)
Controllers are designed for the 4 SISO models of the same plant to
control the flexural vibrations. The effect of placing the sensor at
different locations on the beam is observed and the performance of
the controller is evaluated for vibration control. Conclusions are
finally drawn.
Abstract: The aim of the current work is to present a comparison among three popular optimization methods in the inverse elastostatics problem (IESP) of flaw detection within a solid. In more details, the performance of a simulated annealing, a Hooke & Jeeves and a sequential quadratic programming algorithm was studied in the test case of one circular flaw in a plate solved by both the boundary element (BEM) and the finite element method (FEM). The proposed optimization methods use a cost function that utilizes the displacements of the static response. The methods were ranked according to the required number of iterations to converge and to their ability to locate the global optimum. Hence, a clear impression regarding the performance of the aforementioned algorithms in flaw identification problems was obtained. Furthermore, the coupling of BEM or FEM with these optimization methods was investigated in order to track differences in their performance.
Abstract: The aim of this paper is to confirm the effect of key
design parameters, the punch radius and punch angle, on rupture of the
expansion tube using a finite element analysis with a ductile damage
model. The results of the finite element analysis indicated that the
expansion ratio of the tube was mainly affected by the radius of the
punch. However, the rupture was more affected by the punch angle
than the radius of the punch. The existence of a specific punch angle,
at which rupture did not occur, even if the radius of the punch was
increased, was found.
Abstract: In this paper, free vibration analysis of carbon nanotube (CNT) reinforced laminated composite panels is presented. Three types of panels such as flat, concave and convex are considered for study. Numerical simulation is carried out using commercially available finite element analysis software ANSYS. Numerical homogenization is employed to calculate the effective elastic properties of randomly distributed carbon nanotube reinforced composites. To verify the accuracy of the finite element method, comparisons are made with existing results available in the literature for conventional laminated composite panels and good agreements are obtained. The results of the CNT reinforced composite materials are compared with conventional composite materials under different boundary conditions.
Abstract: In this paper a three dimensional thermal model of a
power toroidal transformer is proposed for both steady-state or
transient conditions. The influence of electric current and ambient
temperature on the temperature distribution, has been investigated.
To validate the three dimensional thermal model, some experimental
tests have been done. There is a good correlation between
experimental and simulation results.
Abstract: Active vibration control is an important problem in
structures. The objective of active vibration control is to reduce the vibrations of a system by automatic modification of the system-s
structural response. In this paper, the modeling and design of a fast
output sampling feedback controller for a smart flexible beam system embedded with shear sensors and actuators for SISO system using
Timoshenko beam theory is proposed. FEM theory, Timoshenko beam theory and the state space techniques are used to model the
aluminum cantilever beam. For the SISO case, the beam is divided into 5 finite elements and the control actuator is placed at finite
element position 1, whereas the sensor is varied from position 2 to 5, i.e., from the nearby fixed end to the free end. Controllers are
designed using FOS method and the performance of the designed FOS controller is evaluated for vibration control for 4 SISO models
of the same plant. The effect of placing the sensor at different locations on the beam is observed and the performance of the
controller is evaluated for vibration control. Some of the limitations of the Euler-Bernoulli theory such as the neglection of shear and
axial displacement are being considered here, thus giving rise to an accurate beam model. Embedded shear sensors and actuators have
been considered in this paper instead of the surface mounted sensors
and actuators for vibration suppression because of lot of advantages. In controlling the vibration modes, the first three dominant modes of
vibration of the system are considered.
Abstract: In this research, the use of light beam size to design the adjustable mirror bender is presented. The focused beam line characterized by its size towards the synchrotron light beam line is investigated. The COSMOSWorks is used in all simulation components of curvature adjustment system to analyze in finite element method. The results based on simulation covers the use of applied forces during adjustment of the mirror radius are presented.
Abstract: In the present paper, the three-dimensional
temperature field of tool is determined during the machining and
compared with experimental work on C45 workpiece using carbide
cutting tool inserts. During the metal cutting operations, high
temperature is generated in the tool cutting edge which influence on
the rate of tool wear. Temperature is most important characteristic of
machining processes; since many parameters such as cutting speed,
surface quality and cutting forces depend on the temperature and high
temperatures can cause high mechanical stresses which lead to early
tool wear and reduce tool life. Therefore, considerable attention is
paid to determine tool temperatures. The experiments are carried out
for dry and orthogonal machining condition. The results show that
the increase of tool temperature depends on depth of cut and
especially cutting speed in high range of cutting conditions.
Abstract: The simulation of extrusion process is studied widely
in order to both increase products and improve quality, with broad
application in wire coating. The annular tube-tooling extrusion was
set up by a model that is termed as Navier-Stokes equation in
addition to a rheological model of differential form based on singlemode
exponential Phan-Thien/Tanner constitutive equation in a twodimensional
cylindrical coordinate system for predicting the
contraction point of the polymer melt beyond the die. Numerical
solutions are sought through semi-implicit Taylor-Galerkin pressurecorrection
finite element scheme. The investigation was focused on
incompressible creeping flow with long relaxation time in terms of
Weissenberg numbers up to 200. The isothermal case was considered
with surface tension effect on free surface in extrudate flow and no
slip at die wall. The Stream Line Upwind Petrov-Galerkin has been
proposed to stabilize solution. The structure of mesh after die exit
was adjusted following prediction of both top and bottom free
surfaces so as to keep the location of contraction point around one
unit length which is close to experimental results. The simulation of
extrusion process is studied widely in order to both increase products
and improve quality, with broad application in wire coating. The
annular tube-tooling extrusion was set up by a model that is termed
as Navier-Stokes equation in addition to a rheological model of
differential form based on single-mode exponential Phan-
Thien/Tanner constitutive equation in a two-dimensional cylindrical
coordinate system for predicting the contraction point of the polymer
melt beyond the die. Numerical solutions are sought through semiimplicit
Taylor-Galerkin pressure-correction finite element scheme.
The investigation was focused on incompressible creeping flow with
long relaxation time in terms of Weissenberg numbers up to 200. The
isothermal case was considered with surface tension effect on free
surface in extrudate flow and no slip at die wall. The Stream Line
Upwind Petrov-Galerkin has been proposed to stabilize solution. The
structure of mesh after die exit was adjusted following prediction of
both top and bottom free surfaces so as to keep the location of
contraction point around one unit length which is close to
experimental results.
Abstract: When the characteristic length of an elastic solid is
down to the nanometer level, its deformation behavior becomes size
dependent. Surface energy /surface stress have recently been applied
to explain such dependency. In this paper, the effect of
strain-independent surface stress on the deformation of an isotropic
elastic solid containing a nanosized elliptical hole is studied by the
finite element method. Two loading cases are considered, in the first
case, hoop stress along the rim of the elliptical hole induced by pure
surface stress is studied, in the second case, hoop stress around the
elliptical opening under combined remote tension and surface stress is
investigated. It has been shown that positive surface stress induces
compressive hoop stress along the hole, and negative surface stress has
opposite effect, maximum hoop stress occurs near the major semi-axes
of the ellipse. Under combined loading of remote tension and surface
stress, stress concentration around the hole can be either intensified or
weakened depending on the sign of the surface stress.
Abstract: A numerical method is proposed to calculate damping
properties for sound-proof structures involving elastic body,
viscoelastic body, and porous media. For elastic and viscoelastic body
displacement is modeled using conventional finite elements including
complex modulus of elasticity. Both effective density and bulk
modulus have complex quantities to represent damped sound fields in
the porous media. Particle displacement in the porous media is
discretised using finite element method. Displacement vectors as
common unknown variables are solved under coupled condition
between elastic body, viscoelastic body and porous media. Further,
explicit expressions of modal loss factor for the mixed structures are
derived using asymptotic method. Eigenvalue analysis and frequency
responded were calculated for automotive test panel laminated
viscoelastic and porous structures using this technique, the results
almost agreed with the experimental results.
Abstract: This paper describes topic of computer simulation with regard to the ground movement above an underground mine. Simulation made with software package ADINA for nonlinear elastic-plastic analysis with finite elements method. The one of representative profiles from Mine 'Stara Jama' in Zenica has been investigated. A collection and selection of both geo-mechanical data and geometric parameters of the mine was necessary for performing these simulations. Results of estimation have been compared with measured values (vertical displacement of surface), and then simulation performed with assumed dynamic and dimensions of excavation, over a period of time. Results are presented with bitmaps and charts.