Abstract: Nanocrystals (NC) alloyed composite CdSxSe1-x(x=0
to 1) have been prepared using the chemical solution deposition
technique. The energy band gap of these alloyed nanocrystals of
approximately the same size, have been determined by scanning
tunneling spectroscopy (STS) technique at room temperature. The
values of the energy band gap obtained directly using STS are
compared to those measured by optical spectroscopy. Increasing the
molar fraction ratio x from 0 to 1 causes clearly observed increase in
the band gap of the alloyed composite nanocrystal. Vegard-s law was
applied to calculate the parameters of the effective mass
approximation (EMA) model and the dimension obtained were
compared to the values measured by STM. The good agreement of
the calculated and measured values is a direct result of applying
Vegard's law in the nanocomposites.
Abstract: Information is a critical asset and an important source for gaining competitive advantage in firms. The effective maintenance of IT becomes an important task. In order to better understand the determinants of IT effectiveness, this study employs the Industrial Organization (I/O) and Resource Based View (RBV) theories and investigates the industry effect and several major firmspecific factors in relation to their impact on firms- IT effectiveness. The data consist of a panel data of ten-year observations of firms whose IT excellence had been recognized by the CIO Magazine. The non-profit organizations were deliberately excluded, as explained later. The results showed that the effectiveness of IT management varied significantly across industries. Industry also moderated the effects of firm demographic factors such as size and age on IT effectiveness. Surprisingly, R & D investment intensity had negative correlation to IT effectiveness. For managers and practitioners, this study offers some insights for evaluation criteria and expectation for IT project success. Finally, the empirical results indicate that the sustainability of IT effectiveness appears to be short in duration.
Abstract: A high energy dual-wavelength extracavity KTA
optical parametric oscillator (OPO) with excellent stability and beam
quality, which is pumped by a Q-switched single-longitudinal-mode
Nd:YAG laser, has been demonstrated based on a type II noncritical
phase matching (NCPM) KTA crystal. The maximum pulse energy of
10.2 mJ with the output stability of better than 4.1% rms at 3.467 μm is
obtained at the repetition rate of 10 Hz and pulse width of 2 ns, and the
11.9 mJ of 1.535 μm radiation is obtained simultaneously. This
extracavity NCPM KTA OPO is very useful when high energy, high
beam quality and smooth time domain are needed.
Abstract: The characterisation of agro-wastes fibres for composite applications from Nigeria using X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM) has been done. Fibres extracted from groundnut shell, coconut husk, rice husk, palm fruit bunch and palm fruit stalk are processed using two novel cellulose fibre production methods developed by the authors. Cellulose apparent crystallinity calculated using the deconvolution of the diffractometer trace shows that the amorphous portion of cellulose was permeable to hydrolysis yielding high crystallinity after treatment. All diffratograms show typical cellulose structure with well-defined 110, 200 and 040 peaks. Palm fruit fibres had the highest 200 crystalline cellulose peaks compared to others and it is an indication of rich cellulose content. Surface examination of the resulting fibres using SEM indicates the presence of regular cellulose network structure with some agglomerated laminated layer of thin leaves of cellulose microfibrils. The surfaces were relatively smooth indicating the removal of hemicellulose, lignin and pectin.
Abstract: The main objective of this study was to remove and recover Ni, Cu and Fe from a mixed metal system using sodium hypophosphite as a reducing agent and nickel powder as seeding material. The metal systems studied consisted of Ni-Cu, Ni-Fe and Ni-Cu-Fe solutions. A 5 L batch reactor was used to conduct experiments where 100 mg/l of each respective metal was used. It was found that the metals were reduced to their elemental form with removal efficiencies of over 80%. The removal efficiency decreased in the order Fe>Ni>Cu. The metal powder obtained contained between 97-99% Ni and was almost spherical and porous. Size enlargement by aggregation was the dominant particulate process.
Abstract: This presentation reviews recent advances in superalloys and thermal barrier coating (TBC) for application in hot sections of energy-efficient gas-turbine engines. It has been reviewed that in the modern combined-cycle gas turbines (CCGT) applying single-crystal energy materials (SC superalloys) and thermal barrier coatings (TBC), and – in one design – closed-loop steam cooling, thermal efficiency can reach more than 60%. These technological advancements contribute to profitable and clean power generation with reduced emission. Alternatively, the use of advanced superalloys (e.g. GTD-111 superalloy, Allvac 718Plus superalloy) and advanced thermal barrier coatings (TBC) in modern gas-turbines has been shown to yield higher energy-efficiency in power generation.
Abstract: This paper introduces a technique for simulating a
single-server exponential queuing system. The technique called the
Q-Simulator is a computer program which can simulate the effect of
traffic intensity on all system average quantities given the arrival
and/or service rates. The Q-Simulator has three phases namely: the
formula based method, the uncontrolled simulation, and the
controlled simulation. The Q-Simulator generates graphs (crystal
solutions) for all results of the simulation or calculation and can be
used to estimate desirable average quantities such as waiting times,
queue lengths, etc.
Abstract: There are few studies on eggshell of leatherback turtle
which is endangered species in Thailand. This study was focusing on
the ultrastructure and elemental composition of leatherback turtle
eggshells collected from Andaman Sea Shore, Thailand during the
nesting season using scanning electron microscope (SEM). Three
eggshell layers of leatherback turtle; the outer cuticle layer or
calcareous layer, the middle layer or middle multistrata layer and the
inner fibrous layer were recognized. The outer calcareous layer was
thick and porosity which consisted of loose nodular units of various
crystal shapes and sizes. The loose attachment between these units
resulted in numerous spaces and openings. The middle layer was
compact thick with several multistrata and contained numerous
openings connecting to both outer cuticle layer and inner fibrous
layer. The inner fibrous layer was compact and thin, and composed of
numerous reticular fibers. Energy dispersive X-ray microanalysis
detector revealed energy spectrum of X-rays character emitted from
all elements on each layer. The percentages of all elements were
found in the following order: carbon (C) > oxygen (O) > calcium
(Ca) > sulfur (S) > potassium (K) > aluminum (Al) > iodine (I) >
silicon (Si) > chlorine (Cl) > sodium (Na) > fluorine (F) >
phosphorus (P) > magnesium (Mg). Each layer consisted of high
percentage of CaCO3 (approximately 98%) implying that it was
essential for turtle embryonic development. A significant difference
was found in the percentages of Ca and Mo in the 3layers. Moreover,
transition metal, metal and toxic non-metal contaminations were
found in leatherback turtle eggshell samples. These were palladium
(Pd), molybdenum (Mo), copper (Cu), aluminum (Al), lead (Pb), and
bromine (Br). The contamination elements were seen in the outer
layers except for Mo. All elements were readily observed and
mapped using Smiling program. X-ray images which mapped the
location of all elements were showed. Calcium containing in the
eggshell appeared in high contents and was widely distributing in
clusters of the outer cuticle layer to form CaCO3 structure. Moreover,
the accumulation of Na and Cl was observed to form NaCl which was
widely distributing in 3 eggshell layers. The results from this study
would be valuable on assessing the emergent success in this
endangered species.
Abstract: The hydrolysis kinetics of polycrystalline lithium hydride (LiH) in argon at various low humidities was measured by gravimetry and Raman spectroscopy with ambient water concentration ranging from 200 to 1200 ppm. The results showed that LiH hydrolysis curve revealed a paralinear shape, which was attributed to two different reaction stages that forming different products as explained by the 'Layer Diffusion Control' model. Based on the model, a novel two-stage rate equation for LiH hydrolysis reactions was developed and used to fit the experimental data for determination of Li2O steady thickness Hs and the ultimate hydrolysis rate vs. The fitted data presented a rise of Hs as ambient water concentration cw increased. However, in spite of the negative effect imposed by Hs increasing, the upward trend of vs remained, which implied that water concentration, rather than Li2O thickness, played a predominant role in LiH hydrolysis kinetics. In addition, the proportional relationship between vsHs and cw predicted by rate equation and confirmed by gravimetric data validated the model in such conditions.
Abstract: In this paper, we present a vertical nanowire thin film transistor with gate-all-around architecture, fabricated using CMOS compatible processes. A novel method of fabricating polysilicon vertical nanowires of diameter as small as 30 nm using wet-etch is presented. Both n-type and p-type vertical poly-silicon nanowire transistors exhibit superior electrical characteristics as compared to planar devices. On a poly-crystalline nanowire of 30 nm diameter, high Ion/Ioff ratio of 106, low drain-induced barrier lowering (DIBL) of 50 mV/V, and low sub-threshold slope SS~100mV/dec are demonstrated for a device with channel length of 100 nm.
Abstract: Highly ordered arrays of TiO2 nanotubes (TiNTs) were grown vertically on Ti foil by electrochemical anodization. We controlled the lengths of these TiNTs from 2.4 to 26.8 ¶üÇóμm while varying the water contents (1, 3, and 6 wt%) of the electrolyte in ethylene glycol in the presence of 0.5 wt% NH4F with anodization for various applied voltages (20–80 V), periods (10–240 min) and temperatures (10–30 oC). For vertically aligned TiNT arrays, not only the increase in their tube lengths, but also their geometric (wall thickness and surface roughness) and crystalline structure lead to a significant influence on photocatalytic activity. The length optimization for methylene blue (MB) photodegradation was 18 μm. Further extending the TiNT length yielded lower photocatalytic activity presumably related to the limited MB diffusion and light-penetration depth into the TiNT arrays. The results indicated that a maximum MB photodegradation rate was obtained for the discrete anatase TiO2 nanotubes with thick and rough walls.
Abstract: Sample of CsAg2I3 was prepared by solid state reaction. Then, microstructure parameters of this sample have been determined using wide angle X-ray scattering WAXS method. As well as, Cell parameters of crystal structure have been refined using CHEKCELL program. This analysis states that the lattice intrinsic strainof the sample is so small and the crystal size is on the order of 559Å.
Abstract: Crystallization has been used for the separation of
chloronitrobenzene or CNBs, which are isomeric substances (o-, mand
p-CNB) and important intermediates in chemical productions. Effects of feed composition on the crystallization of m- and p-CNB was first studied. The results conform to the binary phase diagram of
m- and p-CNB. After that, effects of FAU zeolites (NaX, CaX, BaX, NaY and CaY) above the eutectic composition (63.5 and 65.0 wt% m-CNB in the feed) was also investigated. The results showed that
the FAU zeolites significantly affected the precipitates, the
composition of which was shifted from being rich in m-CNB to rich
in p-CNB. Effects of the number of FAU zeolites on the precipitate composition was then studied. The results revealed that the
precipitates from the lower number of the zeolites had higher p-CNB purity than those from the higher number of zeolite.
Abstract: Samples of CoFe2-xCrxO4 where x varies from 0.0 to 0.5 were prepared by co-precipitation route. These samples were sintered at 750°C for 2 hours. These particles were characterized by X-ray diffraction (XRD) at room temperature. The FCC spinel structure was confirmed by XRD patterns of the samples. The crystallite sizes of these particles were calculated from the most intense peak by Scherrer formula. The crystallite sizes lie in the range of 37-60 nm. The lattice parameter was found decreasing upon substitution of Cr. DC electrical resistivity was measured as a function of temperature. The room temperature thermoelectric power was measured for the prepared samples. The magnitude of Seebeck coefficient depends on the composition and resistivity of the samples.
Abstract: This paper uses quasi-steady molecular statics model
and diamond tool to carry out simulation temperature rise of nanoscale
orthogonal cutting single-crystal silicon. It further qualitatively
analyzes temperature field of silicon workpiece without considering
heat transfer and considering heat transfer. This paper supposes that
the temperature rise of workpiece is mainly caused by two heat sources:
plastic deformation heat and friction heat. Then, this paper develops a
theoretical model about production of the plastic deformation heat and
friction heat during nanoscale orthogonal cutting. After the increased
temperature produced by these two heat sources are added up, the
acquired total temperature rise at each atom of the workpiece is
substituted in heat transfer finite difference equation to carry out heat
transfer and calculates the temperature field in each step and makes
related analysis.
Abstract: In a state-of-the-art industrial production line of
photovoltaic products the handling and automation processes are of
particular importance and implication. While processing a fully
functional crystalline solar cell an as-cut photovoltaic wafer is subject
to numerous repeated handling steps. With respect to stronger
requirements in productivity and decreasing rejections due to defects
the mechanical stress on the thin wafers has to be reduced to a
minimum as the fragility increases by decreasing wafer thicknesses.
In relation to the increasing wafer fragility, researches at the
Fraunhofer Institutes IPA and CSP showed a negative correlation
between multiple handling processes and the wafer integrity. Recent
work therefore focused on the analysis and optimization of the dry
wafer stack separation process with compressed air. The achievement
of a wafer sensitive process capability and a high production
throughput rate is the basic motivation in this research.
Abstract: The present paper discusses the selection of process
parameters for obtaining optimal nanocrystallites size in the CuOZrO2
catalyst. There are some parameters changing the inorganic
structure which have an influence on the role of hydrolysis and
condensation reaction. A statistical design test method is
implemented in order to optimize the experimental conditions of
CuO-ZrO2 nanoparticles preparation. This method is applied for the
experiments and L16 orthogonal array standard. The crystallites size
is considered as an index. This index will be used for the analysis in
the condition where the parameters vary. The effect of pH, H2O/
precursor molar ratio (R), time and temperature of calcination,
chelating agent and alcohol volume are particularity investigated
among all other parameters. In accordance with the results of
Taguchi, it is found that temperature has the greatest impact on the
particle size. The pH and H2O/ precursor molar ratio have low
influences as compared with temperature. The alcohol volume as
well as the time has almost no effect as compared with all other
parameters. Temperature also has an influence on the morphology
and amorphous structure of zirconia. The optimal conditions are
determined by using Taguchi method. The nanocatalyst is studied by
DTA-TG, XRD, EDS, SEM and TEM. The results of this research
indicate that it is possible to vary the structure, morphology and
properties of the sol-gel by controlling the above-mentioned
parameters.
Abstract: Films of pure tin oxide SnO2 and in presence of
antimony atoms (SnO2-Sb) deposited onto glass substrates have
shown a sufficiently high energy gap to be transparent in the visible
region, a high electrical mobility and a carrier concentration which
displays a good electrical conductivity [1]. In this work, the effects of
polycrystalline silicon substrate on the optical properties of pure and
Sb doped tin oxide is investigated.
We used the APCVD (atmospheric pressure chemical vapour
deposition) technique, which is a low-cost and simple technique,
under nitrogen ambient, for growing this material. A series of SnO2
and SnO2-Sb have been deposited onto polycrystalline silicon
substrates with different contents of antimony atoms at the same
conditions of deposition (substrate temperature, flow oxygen,
duration and nitrogen atmosphere of the reactor). The effect of the
substrate in terms of morphology and nonlinear optical properties,
mainly the reflectance, was studied. The reflectance intensity of the
device, compared to the reflectance of tin oxide films deposited
directly on glass substrate, is clearly reduced on the overall
wavelength range. It is obvious that the roughness of the poly-c
silicon plays an important role by improving the reflectance and
hence the optical parameters.
A clear shift in the minimum of the reflectance upon doping level
is observed. This minimum corresponds to strong free carrier
absorption, resulting in different plasma frequency. This effect is
followed by an increase in the reflectance depending of the antimony
doping. Applying the extended Drude theory to the combining
optical and electrical obtained results these effects are discussed.
Abstract: Zeolite A and MCM-41 have extensive applications in basic science, petrochemical science, energy conservation/storage, medicine, chemical sensor, air purification, environmentally benign composite structure and waste remediation. However, the use of zeolite A and MCM-41 in these areas, especially environmental remediation, are restricted due to prohibitive production cost. Efficient recycling of and resource recovery from coal fly ash has been a major topic of current international research interest, aimed at achieving sustainable development of human society from the viewpoints of energy, economy, and environmental strategy. This project reported an original, novel, green and fast methods to produce nano-porous zeolite A and MCM-41 materials from coal fly ash. For zeolite A, this novel production method allows a reduction by half of the total production time while maintaining a high degree of crystallinity of zeolite A which exists in a narrower particle size distribution. For MCM-41, this remarkably green approach, being an environmentally friendly process and reducing generation of toxic waste, can produce pure and long-range ordered MCM-41 materials from coal fly ash. This approach took 24 h at 25 oC to produce 9 g of MCM-41 materials from 30 g of the coal fly ash, which is the shortest time and lowest reaction temperature required to produce pure and ordered MCM-41 materials (having the largest internal surface area) compared to the values reported in the literature. Performance evaluation of the produced zeolite A and MCM-41 materials in wastewater treatment and air pollution control were reported. The residual fly ash was also converted to zeolite Na-P1 which showed good performance in removal of multi-metal ions in wastewater. In wastewater treatment, compared to commercial-grade zeolite A, adsorbents produced from coal fly ash were effective in removing multi heavy metal ions in water and could be an alternative material for treatment of wastewater. In methane emission abatement, the zeolite A (produced from coal fly ash) achieved similar methane removal efficiency compared to the zeolite A prepared from pure chemicals. This report provides the guidance for production of zeolite A and MCM-41 from coal fly ash by a cost-effective approach which opens potential applications of these materials in environmental industry. Finally, environmental and economic aspects of production of zeolite A and MCM-41 from coal fly ash were discussed.
Abstract: The crystalline quality of the AlGaN/GaN high electron mobility transistor (HEMT) structure grown on a 200 mm silicon substrate has been investigated using UV-visible micro- Raman scattering and photoluminescence (PL). The visible Raman scattering probes the whole nitride stack with the Si substrate and shows the presence of a small component of residual in-plane stress in the thick GaN buffer resulting from a wafer bowing, while the UV micro-Raman indicates a tensile interfacial stress induced at the top GaN/AlGaN/AlN layers. PL shows a good crystal quality GaN channel where the yellow band intensity is very low compared to that of the near-band-edge transition. The uniformity of this sample is shown by measurements from several points across the epiwafer.