Abstract: Among the reaction products in the alkali activated ground granulated blast furnace slag (AAS), the layered double hydroxides (LDHs) have a remarkable capacity of chloride and heavy metal ions absorption. The promotion of LDH phases in the AAS matrix can increase chloride resistance. The objective of this study is that using the different dosages of sodium aluminate to activate slag, consequently, promoting the formation of in-situ LDH. The hydration kinetics of the sodium aluminate activated slag (SAAS) was tested by the isothermal calorimetry. Meanwhile, the reaction products were determined by X-ray diffraction (XRD), thermogravimetric analysis (TGA), and Fourier-transform infrared spectroscopy (FTIR). The sodium hydroxide activated slag is selected as the reference. The results of XRD, TGA, and FTIR showed that the formation of LDH in SAAS is governed by the aluminate dosages.
Abstract: The accumulation of heavy metals in food is a constant problem in many parts of the world. Vegetable oils are widely used, both for cooking and for processing in the food industry, meeting the main dietary requirements. One of the main chemical pollutants, heavy metals, is usually found in vegetable oils. These chemical pollutants are carcinogenic, teratogenic and immunotoxic, harmful to consumption and have a negative effect on human health even in trace amounts. Residues of these substances can easily accumulate in vegetable oil during cultivation, processing and storage. In this article, the content of the concentration of heavy metal ions in vegetable oils of Kazakhstan production is studied: sunflower, rapeseed, safflower and linseed oil. Heavy metals: arsenic, cadmium, lead and nickel, were determined in three repetitions by the method of flame atomic absorption. Analysis of vegetable oil samples revealed that the largest lead contamination (Pb) was determined to be 0.065 mg/kg in linseed oil. The content of cadmium (Cd) in the largest amount of 0.009 mg/kg was found in safflower oil. Arsenic (As) content was determined in rapeseed and safflower oils at 0.003 mg/kg, and arsenic (As) was not detected in linseed and sunflower oil. The nickel (Ni) content in the largest amount of 0.433 mg/kg was in linseed oil. The heavy metal contents in the test samples complied with the requirements of regulatory documents for vegetable oils. An assessment of the health risk of vegetable oils with a daily consumption of 36 g per day shows that all samples of vegetable oils produced in Kazakhstan are safe for consumption. But further monitoring is needed, since all these metals are toxic and their harmful effects become apparent only after several years of exposure.
Abstract: The aim of this paper was to study the sorption properties of a blast furnace sludge used as the sorbent. The sorbent was utilized for reduction of content of lead and zinc ions. Sorbent utilized in this work was obtained from metallurgical industry from process of wet gas treatment in iron production. The blast furnace sludge was characterized by X-Ray diffraction, scanning electron microscopy, and XRFS spectroscopy. Sorption experiments were conducted in batch mode. The sorption of metal ions in the sludge was determined by correlation of adsorption isotherm models. The adsorption of lead and zinc ions was best fitted with Langmuir adsorption isotherms. The adsorption capacity of lead and zinc ions was 53.8 mg.g-1 and 10.7 mg.g-1, respectively. The results indicated that blast furnace sludge could be effectively used as secondary material and could be also employed as a low-cost alternative for the removal of heavy metals ions from wastewater.
Abstract: In this work, a new composite adsorbent based on a mesoporous silica SBA-15 with platelet morphology and tin salt of tungstomolybdophosphoric (TWMP) acid was synthesized and applied for uranium adsorption from aqueous solution. The sample was characterized by X-ray diffraction, Fourier transfer infra-red, and N2 adsorption-desorption analysis, and then, effect of various parameters such as concentration of metal ions and contact time on adsorption behavior was examined. The experimental result showed that the adsorption process was explained by the Langmuir isotherm model very well, and predominant reaction mechanism is physisorption. Kinetic data of adsorption suggest that the adsorption process can be described by the pseudo second-order reaction rate model.
Abstract: The tamarind based resin containing hydroxypropane sulphonic acid groups has been synthesized and their adsorption behavior for heavy metal ions has been investigated using batch and column experiments. The hydroxypropane sulphonic acid group has been incorporated onto tamarind by a modified Porath's method of functionalisation of polysaccharides. The tamarind hydroxypropane sulphonic acid (THPSA) resin can selectively remove of heavy metal ions, which are contained in industrial wastewater. The THPSA resin was characterized by FTIR and thermogravimetric analysis. The effects of various adsorption conditions, such as pH, treatment time and adsorbent dose were also investigated. The optimum adsorption condition was found at pH 6, 120 minutes of equilibrium time and 0.1 gram of resin dose. The orders of distribution coefficient values were determined.
Abstract: In this preliminary work, locally available husk of Cajanus cajan (commonly known in India as Tur or Arhar), a bio-waste, has been used in its physically treated and chemically activated form for the removal of binary Cu (II) and Zn(II) ions from the real waste water obtained from an electroplating industry in Bangalore, Karnataka, India and from laboratory prepared binary solutions having almost similar composition of the metal ions, for comparison. The real wastewater after filtration and dilution for five times was used for biosorption studies at the normal pH of the solutions at room temperature. Langmuir's binary model was used to calculate the metal uptake capacities of the biosorbents. It was observed that Cu(II) is more competitive than Zn(II) in biosorption. In individual metal biosorption, Cu(II) uptake was found to be more than that of the Zn(II) and a similar trend was observed in the binary metal biosorption from real wastewater and laboratory prepared solutions. FTIR analysis was carried out to identify the functional groups in the industrial wastewater and EDAX for the elemental analysis of the biosorbents after experiments.
Abstract: Three polyvinyl chloride membrane sensors were developed for the electrochemical evaluation of ferrous, manganese and zinc ions. The sensors were used for assaying metal ions in cervical mucus (CM) of Egyptian river buffalo-cows (Bubalus bubalis) as their levels vary dependent on cyclical hormone variation during different phases of estrus cycle. The presented sensors are based on using ionophores, β-cyclodextrin (β-CD), hydroxypropyl β-cyclodextrin (HP-β-CD) and sulfocalix-4-arene (SCAL) for sensors 1, 2 and 3 for Fe2+, Mn2+ and Zn2+, respectively. Dioctyl phthalate (DOP) was used as the plasticizer in a polymeric matrix of polyvinylchloride (PVC). For increasing the selectivity and sensitivity of the sensors, each sensor was enriched with a suitable complexing agent, which enhanced the sensor’s response. For sensor 1, β-CD was mixed with bathophenanthroline; for sensor 2, porphyrin was incorporated with HP-β-CD; while for sensor 3, oxine was the used complexing agent with SCAL. Linear responses of 10-7-10-2 M with cationic slopes of 53.46, 45.01 and 50.96 over pH range 4-8 were obtained using coated graphite sensors for ferrous, manganese and zinc ionic solutions, respectively. The three sensors were validated, according to the IUPAC guidelines. The obtained results by the presented potentiometric procedures were statistically analyzed and compared with those obtained by atomic absorption spectrophotometric method (AAS). No significant differences for either accuracy or precision were observed between the two techniques. Successful application for the determination of the three studied cations in CM, for the purpose to determine the proper time for artificial insemination (AI) was achieved. The results were compared with those obtained upon analyzing the samples by AAS. Proper detection of estrus and correct time of AI was necessary to maximize the production of buffaloes. In this experiment, 30 multi-parous buffalo-cows were in second to third lactation and weighting 415-530 kg, and were synchronized with OVSynch protocol. Samples were taken in three times around ovulation, on day 8 of OVSynch protocol, on day 9 (20 h before AI) and on day 10 (1 h before AI). Beside analysis of trace elements (Fe2+, Mn2+ and Zn2+) in CM using the three sensors, the samples were analyzed for the three cations and also Cu2+ by AAS in the CM samples and blood samples. The results obtained were correlated with hormonal analysis of serum samples and ultrasonography for the purpose of determining of the optimum time of AI. The results showed significant differences and powerful correlation with Zn2+ composition of CM during heat phase and the ovulation time, indicating that the parameter could be used as a tool to decide optimal time of AI in buffalo-cows.
Abstract: The aim of this work is to present a low cost adsorbent
for removing toxic heavy metals from aqueous solutions. Therefore,
we are interested to investigate the efficiency of natural clay minerals
collected from south Tunisia and their modified form using sulfuric
acid in the removal of toxic metal ions: Zn(II) and Pb(II) from
synthetic waste water solutions. The obtained results indicate that
metal uptake is pH-dependent and maximum removal was detected to
occur at pH 6. Adsorption equilibrium is very rapid and it was
achieved after 90 min for both metal ions studied. The kinetics results
show that the pseudo-second-order model describes the adsorption
and the intraparticle diffusion models are the limiting step. The
treatment of natural clay with sulfuric acid creates more active sites
and increases the surface area, so it showed an increase of the
adsorbed quantities of lead and zinc in single and binary systems. The
competitive adsorption study showed that the uptake of lead was
inhibited in the presence of 10 mg/L of zinc. An antagonistic binary
adsorption mechanism was observed. These results revealed that clay
is an effective natural material for removing lead and zinc in single
and binary systems from aqueous solution.
Abstract: MnO2 nanowires were developed as filtration media for wastewater treatment that uniquely combines several advantages. The resulting material demonstrated strong capability to remove the pollution of heavy metal ions and organic contents in water. In addition, the manufacture process of such material is practical and economical. In this work, MnO2 nanowires were integrated with the state-of-art bio-electrochemical system for wastewater treatment, to overcome problems currently encountered with organic, inorganic, heavy metal, and microbe removal, and to minimize the unit footprint (land/space occupation) at low cost. Results showed that coupling the bio-electrochemical with MnO2 resulted in very encouraging results with higher removal efficiencies of such pollutants.
Abstract: This paper describes the use of by-products as
adsorbents for removing heavy metals from aqueous effluent
solutions. Products of almond skin, walnut shell, saw dust, rice bran
and egg shell were evaluated as metal ion adsorbents in aqueous
solutions. A comparative study was done with commercial adsorbents
like ion exchange resins and activated carbon too. Batch experiments
were investigated to determine the affinity of all of biomasses for,
Cd(ΙΙ), Cr(ΙΙΙ), Ni(ΙΙ), and Pb(ΙΙ) metal ions at pH 5. The rate of
metal ion removal in the synthetic wastewater by the biomass was
evaluated by measuring final concentration of synthetic wastewater.
At a concentration of metal ion (50 mg/L), egg shell adsorbed high
levels (98.6 – 99.7%) of Pb(ΙΙ) and Cr(ΙΙΙ) and walnut shell adsorbed
high levels (35.3 – 65.4%) of Ni(ΙΙ) and Cd(ΙΙ). In this study, it has
been shown that by-products were excellent adsorbents for removal
of toxic ions from wastewater with efficiency comparable to
commercially available adsorbents, but at a reduced cost. Also
statistical studies using Independent Sample t Test and ANOVA Oneway
for statistical comparison between various elements adsorption
showed that there isn’t a significant difference in some elements
adsorption percentage by by-products and commercial adsorbents.
Abstract: Heavy metals have a damaging impact for the environment, animals and humans due to their extreme toxicity and removing them from wastewaters is a very important and interesting task in the field of water pollution control. Biosorption is a relatively new method for treatment of wastewaters and recovery of heavy metals. In this study, a continuous fixed bed study was carried out by using Bacillus thuringiensis as a biosorbent for the removal of Cu and Mn ions from Sarcheshmeh Acid Mine Drainage (AMD). The effect of operating parameters such as flow rate and bed height on the sorption characteristics of B. thuringiensis was investigated at pH 6.0 for each metal ion. The experimental results showed that the breakthrough time decreased with increasing flow rate and decreasing bed height. The data also indicated that the equilibrium uptake of both metals increased with decreasing flow rate and increasing bed height. BDST, Thomas, and Yoon–Nelson models were applied to experimental data to predict the breakthrough curves. All models were found suitable for describing the whole dynamic behavior of the column with respect to flow rate and bed height. In order to regenerate the adsorbent, an elution step was carried out with 1 M HCl and five adsorption-desorption cycles were carried out in continuous manner.
Abstract: Excessive fretting wear at the taper-trunnion junction
(trunnionosis) apparently contributes to the high failure rates of hip
implants. Implant wear and corrosion lead to the release of metal
particulate debris and subsequent release of metal ions at the tapertrunnion
surface. This results in a type of metal poisoning referred to
as metallosis. The consequences of metal poisoning include;
osteolysis (bone loss), osteoarthritis (pain), aseptic loosening of the
prosthesis and revision surgery. Follow up after revision surgery,
metal debris particles are commonly found in numerous locations. Background: A stable connection between the femoral ball head
(taper) and stem (trunnion) is necessary to prevent relative motions
and corrosion at the taper junction. Hence, the importance of
component assembly cannot be over-emphasized. Therefore, the aim
of this study is to determine the influence of head-stem junction
assembly by press fitting and the subsequent
disengagement/disassembly on the connection strength between the
taper ball head and stem. Methods: CoCr femoral heads were assembled with High stainless
hydrogen steel stem (trunnion) by Push-in i.e. press fit; and
disengaged by pull-out test. The strength and stability of the two
connections were evaluated by measuring the head pull-out forces
according to ISO 7206-10 standards. Findings: The head-stem junction strength linearly increases with
assembly forces.
Abstract: Cadmium (II) (Cd) is one of the major toxic elemental
pollutants, which is hazardous for humans, animals and plants. γ-
Polyglutamic acid (γ-PGA) is an extracellular biopolymer produced
by several species of Bacillus which has been reported to be an
effective biosorbent for metal ions. The effect of γ-PGA on growth of
rice grown under laboratory conditions was investigated. Rice seeds
were germinated and then grown at 30±1°C on filter paper soaked
with Cd solution and γ-PGA for 7 days. The result showed that Cd
significantly inhibited the growth of roots, shoots by reducing root,
and shoot lengths. Fresh and dry weights also decreased compared
with control; however, the addition of 500 mg·L-1 γ-PGA alleviated
rice seedlings from the adverse effects of Cd. The analysis of
physiological traits revealed that Cd caused a decrease in the total
chlorophyll and soluble protein contents and amylase activities in all
treatments. The Cd content in seedling tissues increased for the Cd
250 μM treatment (P
Abstract: Superabsorbent polymers received much attention and
are used in many fields because of their superior characters to
traditional absorbents, e.g., sponge and cotton. So, it is very
important but challenging to prepare highly and fast-swelling
superabsorbents. A reliable, efficient and low-cost technique for
removing heavy metal ions from wastewater is the adsorption using
bio-adsorbents obtained from biological materials, such as
polysaccharides-based hydrogels superabsorbents. In this study, novel multi-functional superabsorbent composites
type semi-interpenetrating polymer networks (Semi-IPNs) were
prepared via graft polymerization of acrylamide onto chitosan
backbone in presence of gelatin, CTS-g-PAAm/Ge, using potassium
persulfate and N,N’-methylene bisacrylamide as initiator and
crosslinker, respectively. These hydrogels were also partially
hydrolyzed to achieve superabsorbents with ampholytic properties
and uppermost swelling capacity. The formation of the grafted
network was evidenced by Fourier Transform Infrared Spectroscopy
(ATR-FTIR) and Thermogravimetric Analysis (TGA). The porous
structures were observed by Scanning Electron Microscope (SEM).
From TGA analysis, it was concluded that the incorporation of the Ge
in the CTS-g-PAAm network has marginally affected its thermal
stability. The effect of gelatin content on the swelling capacities of
these superabsorbent composites was examined in various media
(distilled water, saline and pH-solutions). The water absorbency was
enhanced by adding Ge in the network, where the optimum value was
reached at 2 wt. % of Ge. Their hydrolysis has not only greatly
optimized their absorption capacity but also improved the swelling
kinetic.These materials have also showed reswelling ability. We
believe that these super-absorbing materials would be very effective
for the adsorption of harmful metal ions from wastewater.
Abstract: Amoxicillin is an antibiotic which is widely used to
treat various infections in both human beings and animals. However,
when amoxicillin is released into the environment, it is a major
problem. Amoxicillin causes bacterial resistance to these drugs and
failure of treatment with antibiotics. Liquid membrane is of great
interest as a promising method for the separation and recovery of the
target ions from aqueous solutions due to the use of carriers for the
transport mechanism, resulting in highly selectivity and rapid
transportation of the desired metal ions. The simultaneous processes
of extraction and stripping in a single unit operation of liquid
membrane system are very interesting. Therefore, it is practical to
apply liquid membrane, particularly the HFSLM for industrial
applications as HFSLM is proved to be a separation process with
lower capital and operating costs, low energy and extractant with
long life time, high selectivity and high fluxes compared with solid
membranes. It is a simple design amenable to scaling up for industrial
applications. The extraction and recovery for (Amoxicillin) through
the hollow fiber supported liquid membrane (HFSLM) using
aliquat336 as a carrier were explored with the experimental data. The
important variables affecting on transport of amoxicillin viz.
extractant concentration and operating time were investigated. The
highest AMOX- extraction percentages of 85.35 and Amoxicillin
stripping of 80.04 were achieved with the best condition at 6 mmol/L
[aliquat336] and operating time 100 min. The extraction reaction
order (n) and the extraction reaction rate constant (kf) were found to
be 1.00 and 0.0344 min-1, respectively.
Abstract: The adsorption efficiency of fired clayey pellets of 5
and 8 mm diameter size for Cu(II) and Zn(II) ion removal from a
waste printing developer was studied. In order to investigate the
influence of contact time, adsorbent mass and pellet size on the
adsorption efficiency the batch mode was carried out. Faster uptake
of copper ion was obtained with the fired clay pellets of 5 mm
diameter size within 30 minutes. The pellets of 8 mm diameter size
showed the higher equilibrium time (60 to 75 minutes) for copper and
zinc ion. The results pointed out that adsorption efficiency increases
with the increase of adsorbent mass. The maximal efficiency is
different for Cu(II) and Zn(II) ion due to the pellet size. Therefore,
the fired clay pellets of 5 mm diameter size present an effective
adsorbent for Cu(II) ion removal (adsorption efficiency is 63.6%),
whereas the fired clay pellets of 8 mm diameter size are the best
alternative for Zn(II) ion removal (adsorption efficiency is 92.8%)
from a waste printing developer.
Abstract: Removal of various toxic species from aqueous streams is of great importance. Sorption is one of the important remediation procedures as it involves the use of cheap and easily available materials. Also the advantage of regeneration of the sorbent involves the possibility of using novel sorbents. Nanosorbents are very important as the removal is based on the surface phenomena and this is greatly affected by surface charge and area. Functionalization has been very important to bring about the removal of metal ions with greater selectivity.
Abstract: Microbial production of antimicrobials as biopreservatives is the major area of focus nowadays due to increased interest of consumers towards natural and safe preservation of ready to eat food products. The agro-industrial byproduct based medium and optimized process conditions can contribute in economical production of bacteriocins. Keeping this in view, the present investigation was carried out on agro-industrial byproducts utilization for the production of bacteriocin using Enterococcus faecium BS13 isolated from local fermented food. Different agro-industrial byproduct based carbon sources (whey, potato starch liquor, kinnow peel, deoiledrice bran and molasses), nitrogen sources (soya okra, pea pod and corn steep liquor), metal ions and surfactants were tested for optimal bacteriocin production. The effect of various process parameters such as pH, temperature, inoculum level, agitation and time were also tested on bacteriocin production. The optimized medium containing whey, supplemented with 4%corn steep liquor and polysorbate-80 displayed maximum bacteriocin activity with 2% inoculum, at pH 6.5, temperature 40oC under shaking conditions (100 rpm).
Abstract: This paper involves a study of the heavy metal pollution of the soils around one of cement plants in Libya called Suk-Alkhameas and surrounding urban areas caused by cement kiln dust (CKD) emitted. Samples of soil was collected from sites at four directions around the cement factory at distances 250m, 1000m, and 3000m from the factory and at (0-10)cm deep in the soil. These samples are analyzed for Fe (iii), Zn(ii), and Pb (ii) as major pollutants. These values are compared with soils at 25 Km distances from the factory as a reference or control samples. The results show that the concentration of Fe ions in the surface soil was within the acceptable range of 1000ppm. However, for Zn and Pb ions the concentrations at the east and north sides of the factory were found six fold higher than the benchmark level. This high value was attributed to the wind which blows usually from south to north and from west to east. This work includes an investigation of the adsorption isotherms and adsorption efficiency of CKD as adsorbent of heavy metal ions (Fe (iii), Zn(ii), and Pb(ii)) from the polluted soils of Suk-Alkameas city. The investigation was conducted in batch and fixed bed column flow technique. The adsorption efficiency of the studied heavy metals ions removals onto CKD depends on the pH of the solution. The optimum pH values are found to be in the ranges of 8-10 and decreases at lower pH values. The removal efficiency of these heavy metals ions ranged from 93% for Pb, 94% for Zn, and 98% for Fe ions for 10 g.l-1 adsorbent concentration. The maximum removal efficiency of these ions was achieved at 50-60 minutes contact times at which equilibrium is reached. Fixed bed column experimental measurements are also made to evaluate CKD as an adsorbent for the heavy metals. Results obtained are with good agreement with Langmuir and Drachsal assumption of multilayer formation on the adsorbent surface.
Abstract: Heavy metals have bad effects on environment and
soils and it can uptake by natural HAP .natural Hap is an inexpensive
material that uptake large amounts of various heavy metals like Zn
(II) .Natural HAP (N-HAP), extracted from bovine cortical bone ash,
is a good choice for substitution of commercial HAP. Several
experiments were done to investigate the sorption capacity of Zn (II)
to N-HAP in various particles sizes, temperatures, initial
concentrations, pH and reaction times. In this study, the sorption of
Zinc ions from a Zn solution onto HAP particles with sizes of 1537.6
nm and 47.6 nm at three initial pH values of 4.50, 6.00 and 7.50 was
studied. The results showed that better performance was obtained
through a 47.6 nm particle size and higher pH values. The
experimental data were analyzed using Langmuir, Freundlich, and
Arrhenius equations for equilibrium, kinetic and thermodynamic
studies. The analysis showed a maximum adsorption capacity of NHAP
as being 1.562 mmol/g at a pH of 7.5 and small particle size.
Kinetically, the prepared N-HAP is a feasible sorbent that retains Zn
(II) ions through a favorable and spontaneous sorption process.