Abstract: Pervious concrete is a green alternative to conventional pavements with minimal fine aggregate and a high void content. Pervious concrete allows water to infiltrate through the pavement, thereby reducing the runoff and the requirement for stormwater management systems.
Seashell By-Products (SBP) are produced in an important quantity in France and are considered as waste. This work investigated to use SBP in pervious concrete and produce an even more environmentally friendly product, Pervious Concrete Pavers.
The research methodology involved substituting the coarse aggregate in the previous concrete mix design with 20%, 40% and 60% SBP. The testing showed that pervious concrete containing less than 40% SBP had strengths, permeability and void content which are comparable to the pervious concrete containing with only natural aggregate. The samples that contained 40% SBP or higher had a significant loss in strength and an increase in permeability and a void content from the control mix pervious concrete. On the basis of the results in this research, it was found that the natural aggregate can be substituted by SBP without affecting the delicate balance of a pervious concrete mix. Additional, it is recommended that the optimum replacement percentage for SBP in pervious concrete is 40 % direct replacement of natural coarse aggregate while maintaining the structural performance and drainage capabilities of the pervious concrete.
Abstract: The composite pavement system considered in this paper is composed of a functional surface layer, a fiber reinforced asphalt middle layer and a fiber reinforced lean concrete base layer. The mix design of the fiber reinforced lean concrete corresponds to the mix composition of conventional lean concrete but reinforced by fibers. The quasi-absence of research on the durability or long-term performances (fatigue, creep, etc.) of such mix design stresses the necessity to evaluate experimentally the long-term characteristics of this layer composition. This study tests the creep characteristics as one of the long-term characteristics of the fiber reinforced lean concrete layer for composite pavement using a new creep device. The test results reveal that the lean concrete mixed with fiber reinforcement and fly ash develops smaller creep than the conventional lean concrete. The results of the application of the CEB-FIP prediction equation indicate that a modified creep prediction equation should be developed to fit with the new mix design of the layer.
Abstract: The presented paper copes with an experimental evaluation of a model based on modified Weibull size effect theory. Classical statistical Weibull theory was modified by introducing a new parameter (correlation length lp) representing the spatial autocorrelation of a random mechanical properties of material. This size effect modification was observed on two different materials used in civil engineering: unreinforced (plain) concrete and multi-filament yarns made of alkaliresistant (AR) glass which are used for textile-reinforced concrete. The behavior under flexural, resp. tensile loading was investigated by laboratory experiments. A high number of specimens of different sizes was tested to obtain statistically significant data which were subsequently corrected and statistically processed. Due to a distortion of the measured displacements caused by the unstiff experiment device, only the maximal load values were statistically evaluated. Results of the experiments showed a decreasing strength with an increasing sample length. Size effect curves were obtained and the correlation length was fitted according to measured data. Results did not exclude the existence of the proposed new parameter lp.
Abstract: At highly congested reinforcement regions, which is common at beam-column joint area, clear spacing between parallel bars becomes less than maximum normal aggregate size (20mm) which has not been addressed in any design code and specifications. Limited clear spacing between parallel bars (herein after thin cover) is one of the causes which affect anchorage performance. In this study, an experimental investigation was carried out to understand anchorage performance of reinforcement in Self-Compacting Concrete (SCC) and Normal Concrete (NC) at highly congested regions under uni-axial tensile loading. Column bar was pullout whereas; beam bars were offset from column reinforcement creating thin cover as per site condition. Two different sizes of coarse aggregate were used for NC (20mm and 10mm). Strain gauges were also installed along the bar in some specimens to understand the internal stress mechanism. Test results reveal that anchorage performance is affected at highly congested reinforcement region in NC with maximum aggregate size 20mm whereas; SCC and Small Aggregate (10mm) gives better structural performance.
Abstract: Due to urbanization, trees and plants which covered a great land mass of the earth and are an excellent carbon dioxide (CO2) absorber through photosynthesis are being replaced by several concrete based structures. It is therefore important to have these cement based structures absorb the large volume of carbon dioxide which the trees would have removed from the atmosphere during their useful lifespan. Hence the need for these cement based structures to be designed to serve other useful purposes in addition to shelter. This paper reviews the properties of Sodium carbonate and sugar as admixtures in concrete with respect to improving carbon sequestration in concrete.
Abstract: The compressive strength development through
polymerization process of alkaline solution and fly ash blended with Microwave Incinerated Rice Husk Ash (MIRHA) is described in this
paper. Three curing conditions, which are hot gunny curing, ambient
curing, and external humidity curing are investigated to obtain the suitable curing condition for cast in situ provision. Fly ash was
blended with MIRHA at 3%, 5%, and 7% to identify the effect of blended mixes to the compressive strength and microstructure
properties of geopolymer concrete. Compressive strength results
indicated an improvement in the strength development with external humidity curing concrete samples compared to hot gunny curing and
ambient curing. Blended mixes also presented better performance
than control mixes. Improvement of interfacial transition zone (ITZ)
and micro structure in external humidity concrete samples were also
identified compared to hot gunny and ambient curing.
Abstract: The cable tower of Liede Bridge is a double-column curved-lever arched-beam portal framed structure. Being novel and unique in structure, its cable tower differs in complexity from traditional ones. This paper analyzes the ultimate load capacity of cable tower by adopting the finite element calculations and model tests which indicate that constitutive relations applied here give a better simulation of actual failure process of prestressed reinforced concrete. In vertical load, horizontal load and overloading tests, the stepped loading of the tower model is of linear relationship, and the test data has good repeatability. All suggests that the cable tower has good bearing capacity, rational design and high emergency capacity.
Abstract: In the modern construction practices, industrial wastes
or by-products are largely used as raw materials in cement and
concrete. These impart many benefits to the environment and bringabout
an economic impact because the cost of waste disposal is
constantly increasing due to strict environmental regulations. It was
reported in literature that the leakage of oil onto concrete element in
older cement grinding unit resulted in concrete with greater resistance
to freezing and thawing. This effect was thought to be similar to
adding an air-entraining chemical admixture to concrete. This paper
presents an investigation on the load deflection behaviour and crack
patterns of reinforced concrete (RC) beams subjected to four point
loading. Ten 120x260x1900 mm beams were cast with 100%
ordinary Portland cement (OPC) concrete, 20% fly ash (FA) and 20%
rice husk ash (RHA) blended cement concrete. 0.15% dosage of
admixtures (used engine oil, new engine oil, and superplasticizer)
was used throughout the experiment. Results show that OPC and
OPC/RHA RC beams containing used engine oil and superplasticizer
exhibit higher capacity, 18-26% than their corresponding control
mix.
Abstract: Composite steel-concrete slabs using thin-walled
corrugated steel sheets with embossments represent a modern and
effective combination of steel and concrete. However, the design
of new types of sheeting is conditional on the execution of expensive
and time-consuming laboratory testing. The effort to develop
a cheaper and faster method has lead to many investigations all over
the world. In our paper we compare the results from our experiments
involving vacuum loading, four-point bending and small-scale shear
tests.
Abstract: In this study two series of self compacting concrete
mixtures were prepared with 100% coarse recycled concrete
aggregates and different percentages of 0%, 20%, 40%, 60%, 80%
and 100% fine recycled concrete aggregates. In series I and II the
water to binder ratios were 0.50 and 0.45, respectively. The cement
content was kept 350
3 m
kg for those mixtures that don't have any
Nano-Silica. To improve the compressive strength of samples, Nano-
Silica replaced with 10% of cement weight in concrete mixtures. By
doing the tests, the results showed that, adding Nano-silica to the
samples with less percentage of fine recycled concrete aggregates,
lead to more increase on the compressive strength.
Abstract: A reliable estimate of the average bond stress within
the anchorage of steel reinforcing bars in tension is critically
important for the design of reinforced concrete member. This paper
describes part of a recently completed experimental research program
in the Centre for Infrastructure Engineering and Safety (CIES) at the
University of New South Wales, Sydney, Australia aimed at
assessing the effects of different factors on the anchorage
requirements of modern high strength steel reinforcing bars. The
study found that an increase in the anchorage length and bar diameter
generally leads to a reduction of the average ultimate bond stress. By
the extension of a well established analytical model of bond and
anchorage, it is shown here that the differences in the average
ultimate bond stress for different anchorage lengths is associated with
the variable degree of plastic deformation in the tensile zone of the
concrete surrounding the bar.
Abstract: The first and basic cause of the failure of concrete is repeated freezing (thawing) of moisture contained in the pores, microcracks, and cavities of the concrete. On transition to ice, water existing in the free state in cracks increases in volume, expanding the recess in which freezing occurs. A reduction in strength below the initial value is to be expected and further cycle of freezing and thawing have a further marked effect. By using some experimental parameters like nuclear magnetic resonance variation (NMR), enthalpy-temperature (or heat capacity) variation, we can resolve between the various water states and their effect on concrete properties during cooling through the freezing transition temperature range. The main objective of this paper is to describe the principal type of water responsible for the reduction in strength and structural damage (frost damage) of concrete following repeated freeze –thaw cycles. Some experimental work was carried out at the institute of cryogenics to determine what happens to water in concrete during the freezing transition.
Abstract: Reinforced concrete has good durability and excellent structural performance. But there are cases of early deterioration due to a number of factors, one prominent factor being corrosion of steel reinforcement. The process of corrosion sets in due to ingress of moisture, oxygen and other ingredients into the body of concrete, which is unsound, permeable and absorbent. Cracks due to structural and other causes such as creep, shrinkage, etc also allow ingress of moisture and other harmful ingredients and thus accelerate the rate of corrosion. There are several interactive factors both external and internal, which lead to corrosion of reinforcement and ultimately failure of structures. Suitable addition of mineral admixture like silica fume (SF) in concrete improves the strength and durability of concrete due to considerable improvement in the microstructure of concrete composites, especially at the transition zone. Secondary reinforcement in the form of fibre is added to concrete, which provides three dimensional random reinforcement in the entire mass of concrete. Reinforced concrete beams of size 0.1 m X 0.15 m and length 1m have been cast using M 35 grade of concrete. The beams after curing process were subjected to corrosion process by impressing an external Direct Current (Galvanostatic Method) for a period of 15 days under stressed and unstressed conditions. The corroded beams were tested by applying two point loads to determine the ultimate load carrying capacity and cracking pattern and the results of specimens were compared with that of the companion specimens. Gravimetric method is used to quantify corrosion that has occurred.
Abstract: This paper presents the results of an experimental
investigation carried out to evaluate the shrinkage of High Strength
Concrete. High Strength Concrete is made by partially replacement of
cement by flyash and silica fume. The shrinkage of High Strength
Concrete has been studied using the different types of coarse and fine
aggregates i.e. Sandstone and Granite of 12.5 mm size and Yamuna
and Badarpur Sand. The Mix proportion of concrete is 1:0.8:2.2 with
water cement ratio as 0.30. Superplasticizer dose @ of 2% by weight
of cement is added to achieve the required degree of workability in
terms of compaction factor.
From the test results of the above investigation it can be concluded
that the shrinkage strain of High Strength Concrete increases with
age. The shrinkage strain of concrete with replacement of cement by
10% of Flyash and Silica fume respectively at various ages are more
(6 to 10%) than the shrinkage strain of concrete without Flyash and
Silica fume. The shrinkage strain of concrete with Badarpur sand as
Fine aggregate at 90 days is slightly less (10%) than that of concrete
with Yamuna Sand. Further, the shrinkage strain of concrete with
Granite as Coarse aggregate at 90 days is slightly less (6 to 7%) than
that of concrete with Sand stone as aggregate of same size. The
shrinkage strain of High Strength Concrete is also compared with that
of normal strength concrete. Test results show that the shrinkage
strain of high strength concrete is less than that of normal strength
concrete.
Abstract: High Strength Concrete (HSC) is defined as concrete
that meets special combination of performance and uniformity
requirements that cannot be achieved routinely using conventional
constituents and normal mixing, placing, and curing procedures. It is
a highly complex material, which makes modeling its behavior a very
difficult task. This paper aimed to show possible applicability of
Neural Networks (NN) to predict the slump in High Strength
Concrete (HSC). Neural Network models is constructed, trained and
tested using the available test data of 349 different concrete mix
designs of High Strength Concrete (HSC) gathered from a particular
Ready Mix Concrete (RMC) batching plant. The most versatile
Neural Network model is selected to predict the slump in concrete.
The data used in the Neural Network models are arranged in a format
of eight input parameters that cover the Cement, Fly Ash, Sand,
Coarse Aggregate (10 mm), Coarse Aggregate (20 mm), Water,
Super-Plasticizer and Water/Binder ratio. Furthermore, to test the
accuracy for predicting slump in concrete, the final selected model is
further used to test the data of 40 different concrete mix designs of
High Strength Concrete (HSC) taken from the other batching plant.
The results are compared on the basis of error function (or
performance function).
Abstract: In recent years demolished concrete waste handling and management is the new primary challenging issue faced by the countries all over the world. It is very challenging and hectic problem that has to be tackled in an indigenous manner, it is desirable to completely recycle demolished concrete waste in order to protect natural resources and reduce environmental pollution. In this research paper an experimental study is carried out to investigate the feasibility and recycling of demolished waste concrete for new construction. The present investigation to be focused on recycling demolished waste materials in order to reduce construction cost and resolving housing problems faced by the low income communities of the world. The crushed demolished concrete wastes is segregated by sieving to obtain required sizes of aggregate, several tests were conducted to determine the aggregate properties before recycling it into new concrete. This research shows that the recycled aggregate that are obtained from site make good quality concrete. The compressive strength test results of partial replacement and full recycled aggregate concrete and are found to be higher than the compressive strength of normal concrete with new aggregate.
Abstract: Self-compacting concrete (SCC), a new kind of high
performance concrete (HPC) have been first developed in Japan in
1986. The development of SCC has made casting of dense
reinforcement and mass concrete convenient, has minimized noise.
Fresh self-compacting concrete (SCC) flows into formwork and
around obstructions under its own weight to fill it completely and
self-compact (without any need for vibration), without any
segregation and blocking. The elimination of the need for
compaction leads to better quality concrete and substantial
improvement of working conditions. SCC mixes generally have a
much higher content of fine fillers, including cement, and produce
excessively high compressive strength concrete, which restricts its
field of application to special concrete only. To use SCC mixes in
general concrete construction practice, requires low cost materials to
make inexpensive concrete.
Rice husk ash (RHA) has been used as a highly reactive
pozzolanic material to improve the microstructure of the interfacial
transition zone (ITZ) between the cement paste and the aggregate in
self compacting concrete. Mechanical experiments of RHA blended
Portland cement concretes revealed that in addition to the pozzolanic
reactivity of RHA (chemical aspect), the particle grading (physical
aspect) of cement and RHA mixtures also exerted significant
influences on the blending efficiency.
The scope of this research was to determine the usefulness of Rice
husk ash (RHA) in the development of economical self compacting
concrete (SCC). The cost of materials will be decreased by reducing
the cement content by using waste material like rice husk ash instead
of.
This paper presents a study on the development of Mechanical
properties up to 180 days of self compacting and ordinary concretes
with rice-husk ash (RHA), from a rice paddy milling industry in
Rasht (Iran). Two different replacement percentages of cement by
RHA, 10%, and 20%, and two different water/cementicious material
ratios (0.40 and 0.35), were used for both of self compacting and
normal concrete specimens. The results are compared with those of
the self compacting concrete without RHA, with compressive,
flexural strength and modulus of elasticity. It is concluded that RHA
provides a positive effect on the Mechanical properties at age after
60 days.
Base of the result self compacting concrete specimens have higher
value than normal concrete specimens in all test except modulus of
elasticity. Also specimens with 20% replacement of cement by RHA
have the best performance.
Abstract: This paper reports on the influence of surface-treated coarse recycled concrete aggregate (RCA) on developing the compressive strength of concrete. The coarse RCA was initially treated by separately impregnating it in calcium metasilicate (CM) or wollastonite and nanosilica (NS) prepared at various concentrations. The effects of both treatment materials on concrete properties (e.g., slump, density and compressive strength) were evaluated. Scanning electron microscopy (SEM) analysis was performed to examine the microstructure of the resulting concrete. Results show that the effective use of treated coarse RCA significantly enhances the compressive strength of concrete. This result is supported by the SEM analysis, which indicates the formation of a dense interface between the treated coarse RCA and the cement matrix. Coarse RCA impregnated in CM solution results in better concrete strength than NS, and the optimum concentration of CM solution recommended for treated coarse RCA is 10%.
Abstract: In this paper, a parametric experimental study for producing paving blocks using fine and coarse waste glass is presented. Some of the physical and mechanical properties of paving blocks having various levels of fine glass (FG) and coarse glass (CG) replacements with fine aggregate (FA) are investigated. The test results show that the replacement of FG by FA at level of 20% by weight has a significant effect on the compressive strength, flexural strength, splitting tensile strength and abrasion resistance of the paving blocks as compared with the control sample because of puzzolanic nature of FG. The compressive strength, flexural strength, splitting tensile strength and abrasion resistance of the paving block samples in the FG replacement level of 20% are 69%, 90%, 47% and 15 % higher as compared with the control sample respectively. It is reported in the earlier works the replacement of FG by FA at level of 20% by weight suppress the alkali-silica reaction (ASR) in the concrete. The test results show that the FG at level of 20% has a potential to be used in the production of paving blocks. The beneficial effect on these properties of CG replacement with FA is little as compared with FG.
Abstract: This is an application research presenting the
improvement of production quality using the six sigma solutions and
the analyses of benefit-cost ratio. The case of interest is the
production of tile-concrete. Such production has faced with the
problem of high nonconforming products from an inappropriate
surface coating and had low process capability based on the strength
property of tile. Surface coating and tile strength are the most critical
to quality of this product. The improvements followed five stages of
six sigma solutions. After the improvement, the production yield was
improved to 80% as target required and the defective products from
coating process was remarkably reduced from 29.40% to 4.09%. The
process capability based on the strength quality was increased from
0.87 to 1.08 as customer oriented. The improvement was able to save
the materials loss for 3.24 millions baht or 0.11 million dollars. The
benefits from the improvement were analyzed from (1) the reduction
of the numbers of non conforming tile using its factory price for
surface coating improvement and (2) the materials saved from the
increment of process capability. The benefit-cost ratio of overall
improvement was high as 7.03. It was non valuable investment in
define, measure, analyses and the initial of improve stages after that
it kept increasing. This was due to there were no benefits in define,
measure, and analyze stages of six sigma since these three stages
mainly determine the cause of problem and its effects rather than
improve the process. The benefit-cost ratio starts existing in the
improve stage and go on. Within each stage, the individual benefitcost
ratio was much higher than the accumulative one as there was an
accumulation of cost since the first stage of six sigma. The
consideration of the benefit-cost ratio during the improvement
project helps make decisions for cost saving of similar activities
during the improvement and for new project. In conclusion, the
determination of benefit-cost ratio behavior through out six sigma
implementation period provides the useful data for managing quality
improvement for the optimal effectiveness. This is the additional
outcome from the regular proceeding of six sigma.