Abstract: In this paper, shear behavior of reconstituted clay reinforced with varying diameter of sand compaction piles with area replacement-ratio (as) of 6.25, 10.24, 16, 20.25 and 64% in 100mm diameter and 200mm long clay specimens is modeled using consolidated drained and undrained triaxial tests under different confining pressures ranging from 50kPa to 575kPa. The test results show that the stress-strain behavior of the clay was highly influenced by the presence of SCP. The insertion of SCPs into soft clay has shown to have a positive effect on the load carrying capacity of the clay, resulting in a composite soil mass that has greater shear strength and improved stiffness compared to the unreinforced clay due to increased reinforcement area ratio. In addition, SCP also acts as vertical drain in the clay thus accelerating the dissipation of excess pore water pressures that are generated during loading by shortening the drainage path and activating radial drainage, thereby reducing post-construction settlement. Thus, sand compaction piles currently stand as one of the most viable and practical techniques for improving the mechanical properties of soft clays.
Abstract: Increasing our ability to solve complex engineering problems is directly related to the processing capacity of computers. By means of such equipments, one is able to fast and accurately run numerical algorithms. Besides the increasing interest in numerical simulations, probabilistic approaches are also of great importance. This way, statistical tools have shown their relevance to the modelling of practical engineering problems. In general, statistical approaches to such problems consider that the random variables involved follow a normal distribution. This assumption tends to provide incorrect results when skew data is present since normal distributions are symmetric about their means. Thus, in order to visualize and quantify this aspect, 9 statistical distributions (symmetric and skew) have been considered to model a hypothetical slope stability problem. The data modeled is the friction angle of a superficial soil in Brasilia, Brazil. Despite the apparent universality, the normal distribution did not qualify as the best fit. In the present effort, data obtained in consolidated-drained triaxial tests and saturated direct shear tests have been modeled and used to analytically derive the probability density function (PDF) of the safety factor of a hypothetical slope based on Mohr-Coulomb rupture criterion. Therefore, based on this analysis, it is possible to explicitly derive the failure probability considering the friction angle as a random variable. Furthermore, it is possible to compare the stability analysis when the friction angle is modelled as a Dagum distribution (distribution that presented the best fit to the histogram) and as a Normal distribution. This comparison leads to relevant differences when analyzed in light of the risk management.
Abstract: This paper presents an analytical study on the
behavior of reinforced concrete walls with rectangular cross section.
Several experiments on such walls have been selected to be studied.
Database from various experiments were collected and nominal shear
wall strengths have been calculated using formulas, such as those of
the ACI (American), NZS (New Zealand), Mexican (NTCC), and
Wood and Barda equations. Subsequently, nominal shear wall
strengths from the formulas were compared with the ultimate shear
wall strengths from the database. These formulas vary substantially in
functional form and do not account for all variables that affect the
response of walls. There is substantial scatter in the predicted values
of ultimate shear strength. Two new semi empirical equations are
developed using data from tests of 57 walls for transitions walls and
27 for slender walls with the objective of improving the prediction of
peak strength of walls with the most possible accurate.
Abstract: A composite material with carbon fiber and polymer
matrix has been used as adherent for manufacturing adhesive joints.
In order to evaluate different fiber orientations on joint performance,
the adherents with the 0°, ±15°, ±30°, ±45° fiber orientations were
used in the single lap joint configuration. The joints with an overlap
length of 25 mm were prepared according to the ASTM 1002
specifications and subjected to tensile loadings. The structural
adhesive used was a two-part epoxy to be cured at 70°C for an hour.
First, mechanical behaviors of the adherents were measured using
three point bending test. In the test, considerations were given to
stress to failure and elastic modulus. The results were compared with
theoretical ones using rule of mixture. Then, the joints were
manufactured in a specially prepared jig, after a proper surface
preparation. Experimental results showed that the fiber orientations
of the adherents affected the joint performance considerably; the
joints with ±45° adherents experienced the worst shear strength, half
of those with 0° adherents, and in general, there was a great
relationship between the fiber orientations and failure mechanisms.
Delamination problems were observed for many joints, which were
thought to be due to peel effects at the ends of the overlap. It was
proved that the surface preparation applied to the adherent surface
was adequate. For further explanation of the results, a numerical
work should be carried out using a possible non-linear analysis.
Abstract: The end panels of a large rectangular industrial duct,
which experience significant internal pressures, also experience
considerable transverse shear due to transfer of gravity loads to the
supports. The current design practice of such thin plate panels for
shear load is based on methods used for the design of plate girder
webs. The structural arrangements, the loadings and the resulting
behavior associated with the industrial duct end panels are, however,
significantly different from those of the web of a plate girder. The
large aspect ratio of the end panels gives rise to multiple bands of
tension fields, whereas the plate girder web design is based on one
tension field. In addition to shear, the industrial end panels are
subjected to internal pressure which in turn produces significant
membrane action. This paper reports a study which was undertaken
to review the current industrial analysis and design methods and to
propose a comprehensive method of designing industrial duct end
panels for shear resistance. In this investigation, a nonlinear finite element model was
developed to simulate the behavior of industrial duct end panel, along
with the associated edge stiffeners, subjected to transverse shear and
internal pressures. The model considered the geometric imperfections
and constitutive relations for steels. Six scale independent
dimensionless parameters that govern the behavior of such end panel
were identified and were then used in a parametric study. It was
concluded that the plate slenderness dominates the shear strength of
stockier end panels, and whereas, both the plate slenderness and the
aspect ratio influence the shear strength of slender end panels. Based
on these studies, this paper proposes design aids for estimating the
shear strength of rectangular duct end panels.
Abstract: The floor beams of steel buildings, cold-formed steel
floor joists in particular, often require large web openings, which may
affect their shear capacities. A cost effective way to mitigate the
detrimental effects of such openings is to weld/fasten reinforcements.
A difficulty associated with an experimental investigation to establish
suitable reinforcement schemes for openings in shear zone is that
moment always coexists with the shear, and thus, it is impossible to
create pure shear state in experiments, resulting in moment
influenced results. However, Finite Element Method (FEM) based
analysis can be conveniently used to investigate the pure shear
behaviour of webs including webs with reinforced openings. This
paper presents the details associated with the finite element analysis
of thick/thin-plates (representing the web of hot-rolled steel beam,
and the web of a cold-formed steel member) having a large
reinforced opening. The study considered simply-supported
rectangular plates subjected to in-plane shear loadings until failure
(including post-buckling behaviour). The plate was modelled using
geometrically non-linear quadrilateral shell elements, and non-linear
stress-strain relationship based on experiments. Total Langrangian
with large displacement/small strain formulation was used for such
analyses. The model also considered the initial geometric
imperfections. This study considered three reinforcement schemes,
namely, flat, lip, and angle reinforcements. This paper discusses the
modelling considerations and presents the results associated with the
various reinforcement schemes under consideration.
Abstract: This work presents an improved single fiber pull-out
test for fiber/matrix interface characterization. This test has been
used to study the Inter-Facial Shear Strength ‘IFSS’ of hemp fibers
reinforced polypropylene (PP). For this aim, the fiber diameter
has been carefully measured using a tomography inspired method.
The fiber section contour can then be approximated by a circle
or a polygon. The results show that the IFSS is overestimated if
the circular approximation is used. The Influence of the molding
temperature on the IFSS has also been studied. We find that a molding
temperature of 183◦C leads to better interfacial properties. Above or
below this temperature the interface strength is reduced.
Abstract: The economic use and ease of construction of profiled
deck composite slab is marred with the complex and un-economic
strength verification required for the serviceability and general safety
considerations. Beside these, albeit factors such as shear span length,
deck geometries and mechanical frictions greatly influence the
longitudinal shear strength, that determines the ultimate strength of
profiled deck composite slab, and number of methods available for its
determination; partial shear and slope-intercept are the two methods
according to Euro-code 4 provision. However, the complexity
associated with shear behavior of profiled deck composite slab, the
use of these methods in determining the load carrying capacities of
such slab yields different and conflicting values. This couple with the
time and cost constraint associated with the strength verification is a
source of concern that draws more attentions nowadays, the issue is
critical. Treating some of these known shear strength influencing
factors as random variables, the load carrying capacity violation of
profiled deck composite slab from the use of the two-methods
defined according to Euro-code 4 are determined using reliability
approach, and comparatively studied. The study reveals safety values
from the use of m-k method shows good standing compared with that
from the partial shear method.
Abstract: Numerical investigations were conducted to study the
influence of flexural reinforcement ratio on the diagonal cracking
strength and ultimate shear strength of reinforced concrete (RC)
beams without stirrups. Three-dimensional nonlinear finite element
analyses (FEAs) of the beams with flexural reinforcement ratios
ranging from 0.58% to 2.20% subjected to a mid-span concentrated
load were carried out. It is observed that the load-deflection and loadstrain
curves obtained from the numerical analyses agree with those
obtained from the experiments. It is concluded that flexural
reinforcement ratio has a significant effect on the shear strength and
deflection capacity of RC beams without stirrups. The predictions of
diagonal cracking strength and ultimate shear strength of beams
obtained by using the equations defined by a number of codes and
researchers are compared with each other and with the experimental
values.
Abstract: Under active stress conditions, a rigid cantilever
retaining wall tends to rotate about a pivot point located within the
embedded depth of the wall. For purely granular and cohesive soils, a
methodology was previously reported called minimization of moment
ratio to determine the location of the pivot point of rotation. The
usage of this new methodology is to estimate the rotational stability
safety factor. Moreover, the degree of improvement required in a
backfill to get a desired safety factor can be estimated by the concept
of the shear strength demand. In this article, the accuracy of this
method for another type of cantilever walls called Contiguous Bored
Pile (CBP) retaining wall is evaluated by using physical modeling
technique. Based on observations, the results of moment ratio
minimization method are in good agreement with the results of the
carried out physical modeling.
Abstract: The California Bearing Ratio (CBR) has been
acknowledged as an important parameter to characterize the bearing
capacity of earth structures, such as earth dams, road embankments,
airport runways, bridge abutments and pavements. Technically, the
CBR test can be carried out in the laboratory or in the field. The CBR
test is time-consuming and is infrequently performed due to the
equipment needed and the fact that the field moisture content keeps
changing over time. Over the years, many correlations have been
developed for the prediction of CBR by various researchers,
including the dynamic cone penetrometer, undrained shear strength
and Clegg impact hammer. This paper reports and discusses some of
the results from a study on the prediction of CBR. In the current
study, the CBR test was performed in the laboratory on some finegrained
subgrade soils collected from various locations in Victoria.
Based on the test results, a satisfactory empirical correlation was
found between the CBR and the physical properties of the
experimental soils.
Abstract: The prepreg process among the CFRP (Carbon Fiber
Reinforced Plastic) forming methods is the short term of
‘Pre-impregnation’, which is widely used for aerospace composites
that require a high quality property such as a fiber-reinforced woven
fabric, in which an epoxy hardening resin is impregnated the reality.
However, that this process requires continuous researches and
developments for its commercialization because the delamination
characteristically develops between the layers when a great weight is
loaded from outside to supplement such demerit, three lamination
methods among the prepreg lamination methods of CFRP were
designed to minimize the delamination between the layers due to
external impacts. Further, the newly designed methods and the
existing lamination methods were analyzed through a mechanical
characteristic test, Interlaminar Shear Strength test. The Interlaminar
Shear Strength test result confirmed that the newly proposed three
lamination methods, i.e. the Roll, Half and Zigzag laminations,
presented more excellent strengths compared to the conventional Ply
lamination. The interlaminar shear strength in the roll method with
relatively dense fiber distribution was approximately 1.75% higher
than that in the existing ply lamination method, and in the half method,
it was approximately 0.78% higher.
Abstract: The effect of particle size on shear strength of
granular materials are investigated using direct shear tests. Small
direct shear test (60 mm by 60 mm by 24 mm deep) were conducted
for particles passing the sieves with opening size of 2.36 mm.
Meanwhile, particles passing the standard 20 mm sieves were tested
using large direct shear test (300 mm by 300 mm by 200 mm deep).
The large direct shear tests and the small direct shear tests carried out
using the same shearing rate of 0.09 mm/min and similar normal
stresses of 100, 200 and 300 kPa. The results show that the peak and
residual shear strength increases as particle size increases.
Abstract: Three dimensional non-Interlaced carbon fibre
reinforced silicon carbide (3-D-Cf/SiC) composites with pyrocarbon
interphase were fabricated using isothermal chemical vapor
infiltration (ICVI) combined with polymer impregnation pyrolysis
(PIP) process. Polysilazane (PSZ) is used as a preceramic polymer to
obtain silicon carbide matrix. Thermo gravimetric analysis (TGA),
Infrared spectroscopic analysis (IR) and X-ray diffraction (XRD)
analysis were carried out on PSZ pyrolysed at different temperatures
to understand the pyrolysis and obtaining the optimum pyrolysing
condition to yield β-SiC phase. The density of the composites was
1.94 g cm-3 after the 3-D carbon preform was SiC infiltrated for 280 h
with one intermediate polysilazane pre-ceramic PIP process.
Mechanical properties of the composite materials were investigated
under tensile, flexural, shear and impact loading. The values of
tensile strength were 200 MPa at room temperature (RT) and 195
MPa at 500°C in air. The average RT flexural strength was 243 MPa.
The lower flexural strength of these composites is because of the
porosity. The fracture toughness obtained from single edge notched
beam (SENB) technique was 39 MPa.m1/2. The work of fracture
obtained from the load-displacement curve of SENB test was 22.8
kJ.m-2. The composites exhibited excellent impact resistance and the
dynamic fracture toughness of 44.8 kJ.m-2 is achieved as determined
from instrumented Charpy impact test. The shear strength of the
composite was 93 MPa, which is significantly higher compared 2-D
Cf/SiC composites. Microstructure evaluation of fracture surfaces
revealed the signatures of fracture processes and showed good
support for the higher toughness obtained.
Abstract: Interlaminar shear strength (ILSS) of fiber reinforced polymer composite is an important property for most of the structural applications. Matrix modification is an effective method used to improve the interlaminar shear strength of composite. In this paper, EPON 862/w epoxy system was modified using Tetraethyl orthosilicate (TEOS) electrospun nanofibers (ENFs) which were produced using electrospinning method. Unmodified and nanofibers modified resins were used to fabricate glass fiber reinforced polymer composite (GFRP) using H-VARTM method. The ILSS of the Glass Fiber Reinforced Polymeric Composites (GFRP) was investigated. The study shows that introduction of TEOS ENFs in the epoxy resin enhanced the ILSS of GFRPby 15% with 0.6% wt. fraction of TEOS ENFs.
Abstract: Most failures of soil have been attributed to poor shear strength. Consequently, the present paper investigated the suitability of cattle bone ash as a possible additive to improve the shear strength of soils. Four soil samples were collected and stabilized with prepared bone ash in proportions of 3%, 5%, 7%, 10%, 15% and 20% by dry weight. Chemical analyses of the bone ash; followed by classification, compaction, and triaxial shear tests of the treated soil samples were conducted. Results obtained showed that bone ash contained high proportion of calcium oxide and phosphate. Addition of bone ash to soil samples led to increase in soil shear strengths within the range of 22.40% to 105.18% over the strengths of the respective control tests. Conversely, all samples attained maximum shear strengths at 7% bone ash stabilization. The use of bone ash as an additive will therefore improve the shear strength of soils; however, using bone ash quantities in excess of 7% may not yield ample results.
Abstract: Strength recovery effect from the residual-state of shear is not well address in scientific literature. Torsional ring shear strength recovery tests on kaolin clay using rest periods up to 30 days are performed at the effective normal stress 100kN/m2. Test results shows that recovered strength measured in the laboratory is slightly noticeable after rest period of 3 days, but recovered strength lost after very small shear displacement. This paper mainly focused on the strength recovery phenomenon from the residual strength of kaolin clay based on torsional ring shear test results. Mechanisms of recovered strength are also discussed.
Abstract: This paper describes a method for preparing metallic Cu nanoparticles in aqueous solution, and a metal-metal bonding technique using the Cu particles.Preparation of the Cu particle colloid solution was performed in water at room temperature in air using a copper source (0.01 M Cu(NO3)2), a reducing reagent (0.2 - 1.0 M hydrazine), and stabilizers (0.5×10-3 M citric acid and 5.0×10-3 M cetyltrimethylammonium bromide). The metallic Cu nanoparticles with sizes of ca. 60nm were prepared at all the hydrazine concentrations examined. A stage and a plate of metallic Cu were successfully bonded under annealing at 400oC and pressurizing at 1.2 MPa for 5min in H2 gas with help of the metallic Cu particles. A shear strength required for separating the bonded Cu substrates reached the maximum value at a hydrazine concentration of 0.8M, and it decreased beyond the concentration. Consequently, the largest shear strength of 22.9 MPa was achieved at the 0.8 M hydrazine concentration.
Abstract: Microbial-induced calcite precipitation (MICP) is a
relatively green and sustainable soil improvement technique. It
utilizes biochemical process that exists naturally in soil to improve
engineering properties of soils. The calcite precipitation process is
uplifted by the mean of injecting higher concentration of urease
positive bacteria and reagents into the soil. The main objective of this
paper is to provide an overview of the factors affecting the MICP in
soil. Several factors were identified including nutrients, bacteria type,
geometric compatibility of bacteria, bacteria cell concentration,
fixation and distribution of bacteria in soil, temperature, reagents
concentration, pH, and injection method. These factors were found to
be essential for promoting successful MICP soil treatment.
Furthermore, a preliminary laboratory test was carried out to
investigate the potential application of the technique in improving the
shear strength and impermeability of a residual soil specimen. The
results showed that both shear strength and impermeability of
residual soil improved significantly upon MICP treatment. The
improvement increased with increasing soil density.
Abstract: Numerous experimental tests for post-installed anchor systems drilled in hardened concrete were conducted in order to estimate pull-out and shear strength accounting for uncertainties such as torque ratios, embedment depths and different diameters in demands. In this study, the strength of the systems was significantly changed by the effect of those three uncertainties during pull-out experimental tests, whereas the shear strength of the systems was not affected by torque ratios. It was also shown that concrete cone failure or damage mechanism was generally investigated during and after pull-out tests and in shear strength tests, mostly the anchor systems were failed prior to failure of primary structural system. Furthermore, 3D finite element model for the anchor systems was created by ABAQUS for the numerical analysis. The verification of finite element model was identical till the failure points to the load-displacement relationship specified by the experimental tests.