Abstract: The information of the impact cutting behavior of plants stalk plays an important role in the design and fabrication of plants cutting equipment. It is difficult to investigate a theoretical method for defining cutting properties of plants stalks because the cutting process is complex. Thus, it is necessary to set up an experimental approach to determine cutting parameters for a single stalk. To measure the shear force, shear energy and shear strength of plant stalk, a special impact cutting tester was fabricated. It was similar to an Izod impact cutting tester for metals but a cutting blade and data acquisition system were attached to the end of pendulum's arm. The apparatus was included four strain gages and a digital indicator to show the real-time cutting force of plant stalk. To measure the shear force and also testing the apparatus, two plants’ stalks, like buxus and privet, were selected. The samples (buxus and privet stalks) were cut under impact cutting process at four loading rates 1, 2, 3 and 4 m.s-1 and three internodes fifth, tenth and fifteenth by the apparatus. At buxus cutting analysis: the minimum value of cutting energy was obtained at fifth internode and loading rate 4 m.s-1 and the maximum value of shear energy was obtained at fifteenth internode and loading rate 1 m.s-1. At privet cutting analysis: the minimum value of shear consumption energy was obtained at fifth internode and loading rate: 4 m.s-1 and the maximum value of shear energy was obtained at fifteenth internode and loading rate: 1 m.s-1. The statistical analysis at both plants showed that the increase of impact cutting speed would decrease the shear consumption energy and shear strength. In two scenarios, the results showed that with increase the cutting speed, shear force would decrease.
Abstract: Over recent years, due to increased population and increased waste production, groundwater protection has become more important, therefore, designing engineered barrier systems such as landfill liners to prevent the entry of leachate into groundwater should be done with greater accuracy. These measures generally involve the application of low permeability soils such as clays. Bentonite is a natural clay with low permeability which makes it a suitable soil for using in liners. Also zeolite with high cation exchange capacity can help to reduce of hazardous materials risk. Bentonite expands when wet, absorbing as much as several times its dry mass in water. This property may effect on some structural properties of soil such as shear strength. In present study, shear strength parameters are determined by both leachates polluted and not polluted bentonite-amended zeolite soil with mixing rates (B/Z) of 5%-10% and 20% with unconfined compression test to obtain the differences. It is shown that leachate presence causes reduction in resistance in general.
Abstract: In recent years, the occurrence of several liquefactions in sandy soils containing various values of clay content has shown that in addition to silty sands, clayey sands are also susceptible to liquefaction. Therefore, it is necessary to investigate the properties of these soil compositions and their behavioral characteristics. This paper presents the effect of clay fines on the undrained shear strength of sands at various confining pressures. For this purpose, a series of unconsolidated undrained triaxial shear tests were carried out on clean sand and sand mixed with 5, 10, 15, 20, and 30 percent of clay fines. It was found that the presence of clay particle in sandy specimens change the dilative behavior to contraction. The result also showed that increasing the clay fines up to 10 percent causes to increase the potential for liquefaction, and decreases it at higher values fine content. These results reveal the important role of clay particles in changing the undrained strength of the sandy soil.
Abstract: To investigate seismic performance of beam-column knee joints, four full-scale reinforced concrete beam-column knee joints, which were fabricated to simulate those in as-built RC frame buildings designed to ACI 318-14 and ACI-ASCE 352R-02, were tested under reversed cyclic loading. In the experimental programme, particular emphasis was given to the effect of horizontal reinforcement (in format of inverted U-shape bars) on the shear strength and ductility capacity of knee joints. Test results are compared with those predicted by four seismic design codes, including ACI 318-14, EC8, NZS3101 and GB50010. It is seen that the current design codes of practice cannot accurately predict the shear strength of seismically designed knee joints.
Abstract: Out of all methods for ground improvement, stone column became more popular these days due to its simple construction and economic consideration. Installation of stone column especially in loose fine graded soil causes increasing in load bearing capacity and settlement reduction. Encased granular stone columns (EGCs) are commonly subjected to vertical load. However, they may also be subjected to significant amount of shear loading. In this study, three-dimensional finite element (FE) analyses were conducted to estimate the shear load capacity of EGCs in sandy soil. Two types of different cases, stone column and geosynthetic encased stone column were studied at different normal pressures varying from 15 kPa to 75 kPa. Also, the effect of diameter in two cases was considered. A close agreement between the experimental and numerical curves of shear stress - horizontal displacement trend line is observed. The obtained result showed that, by increasing the normal pressure and diameter of stone column, higher shear strength is mobilized by soil; however, in the case of encased stone column, increasing the diameter had more dominated effect in mobilized shear strength.
Abstract: The stability of structures made of light-gauge steel depends highly on the contribution of Shear Wall Panel (SWP) systems under horizontal forces due to wind or earthquake loads. Steel plate sheathing is often used with these panels made of cold formed steel (CFS) to improve its shear strength. In order to predict the shear strength resistance, two methods are presented in this paper. In the first method, the steel plate sheathing is modeled with plats strip taking into account only the tension and compression force due to the horizontal load, where both track and stud are modeled according to the geometrical and mechanical characteristics of the specimen used in the experiments. The theoretical background and empirical formulations of this method are presented in this paper. However, the second method is based on a micro modeling of the cold formed steel Shear Wall Panel “CFS-SWP” using Abaqus software. A nonlinear analysis was carried out with an in-plan monotonic load. Finally, the comparison between these two methods shows that the micro modeling with Abaqus gives better prediction of shear resistance of SWP than strips method. However, the latter is easier and less time consuming than the micro modeling method.
Abstract: This paper presents an analytical study on the
behavior of reinforced concrete walls with rectangular cross section.
Several experiments on such walls have been selected to be studied.
Database from various experiments were collected and nominal shear
wall strengths have been calculated using formulas, such as those of
the ACI (American), NZS (New Zealand), Mexican (NTCC), and
Wood and Barda equations. Subsequently, nominal shear wall
strengths from the formulas were compared with the ultimate shear
wall strengths from the database. These formulas vary substantially in
functional form and do not account for all variables that affect the
response of walls. There is substantial scatter in the predicted values
of ultimate shear strength. Two new semi empirical equations are
developed using data from tests of 57 walls for transitions walls and
27 for slender walls with the objective of improving the prediction of
peak strength of walls with the most possible accurate.
Abstract: Numerical investigations were conducted to study the
influence of flexural reinforcement ratio on the diagonal cracking
strength and ultimate shear strength of reinforced concrete (RC)
beams without stirrups. Three-dimensional nonlinear finite element
analyses (FEAs) of the beams with flexural reinforcement ratios
ranging from 0.58% to 2.20% subjected to a mid-span concentrated
load were carried out. It is observed that the load-deflection and loadstrain
curves obtained from the numerical analyses agree with those
obtained from the experiments. It is concluded that flexural
reinforcement ratio has a significant effect on the shear strength and
deflection capacity of RC beams without stirrups. The predictions of
diagonal cracking strength and ultimate shear strength of beams
obtained by using the equations defined by a number of codes and
researchers are compared with each other and with the experimental
values.
Abstract: Most failures of soil have been attributed to poor shear strength. Consequently, the present paper investigated the suitability of cattle bone ash as a possible additive to improve the shear strength of soils. Four soil samples were collected and stabilized with prepared bone ash in proportions of 3%, 5%, 7%, 10%, 15% and 20% by dry weight. Chemical analyses of the bone ash; followed by classification, compaction, and triaxial shear tests of the treated soil samples were conducted. Results obtained showed that bone ash contained high proportion of calcium oxide and phosphate. Addition of bone ash to soil samples led to increase in soil shear strengths within the range of 22.40% to 105.18% over the strengths of the respective control tests. Conversely, all samples attained maximum shear strengths at 7% bone ash stabilization. The use of bone ash as an additive will therefore improve the shear strength of soils; however, using bone ash quantities in excess of 7% may not yield ample results.
Abstract: Soft clays are defined as cohesive soil whose water
content is higher than its liquid limits. Thus, soil-cement mixing is
adopted to improve the ground conditions by enhancing the strength
and deformation characteristics of the soft clays. For the above
mentioned reasons, a series of laboratory tests were carried out to
study some fundamental mechanical properties of cement stabilized
soft clay. The test specimens were prepared by varying the portion of
ordinary Portland cement to the soft clay sample retrieved from the
test site of RECESS (Research Centre for Soft Soil). Comparisons
were made for both homogeneous and columnar system specimens
by relating the effects of cement stabilized clay of for 0, 5 and 10 %
cement and curing for 3, 28 and 56 days. The mechanical properties
examined included one-dimensional compressibility and undrained
shear strength. For the mechanical properties, both homogeneous and
columnar system specimens were prepared to examine the effect of
different cement contents and curing periods on the stabilized soil.
The one-dimensional compressibility test was conducted using an
oedometer, while a direct shear box was used for measuring the
undrained shear strength. The higher the value of cement content, the
greater is the enhancement of the yield stress and the decrease of
compression index. The value of cement content in a specimen is a
more active parameter than the curing period.
Abstract: This research investigates the suitability of fuel oil in
improving gypseous soil. A detailed laboratory tests were carried-out
on two soils (soil I with 51.6% gypsum content, and soil II with
26.55%), where the two soils were obtained from Al-Therthar site
(Al-Anbar Province-Iraq).
This study examines the improvement of soil properties using the
gypsum material which is locally available with low cost to minimize
the effect of moisture on these soils by using the fuel oil. This study
was conducted on two models of the soil gypsum, from the Tharthar
area. The first model was sandy soil with Gypsum content of (51.6%)
and the second is clayey soil and the content of Gypsum is (26.55%).
The program included tests measuring the permeability and
compressibility of the soil and their collapse properties. The shear
strength of the soil and the amounts of weight loss of fuel oil due to
drying had been found. These tests have been conducted on the
treated and untreated soils to observe the effect of soil treatment on
the engineering properties when mixed with varying degrees of fuel
oil with the equivalent of the water content.
The results showed that fuel oil is a good material to modify the
basic properties of the gypseous soil of collapsibility and
permeability, which are the main problems of this soil and retained
the soil by an appropriate amount of the cohesion suitable for
carrying the loads from the structure.