Abstract: Since Network-on-Chip (NoC) uses network
interfaces (NIs) to improve the design productivity, by now, there
have been a few papers addressing the design and implementation of a
NI module. However, none of them considered the difference of
address encoding methods between NoC and the traditional
bus-shared architecture. On the basis of this difference, in the paper,
we introduce a transmit mechanism to solve such a problem for global
asynchronous locally synchronous (GALS) NoC. Furthermore, we
give the concrete implementation of the NI module in this transmit
mechanism. Finally, we evaluate its performance and area overhead
by a VHDL-based cycle-accurate RTL model and simulation results
confirm the validity of this address-oriented transmit mechanism.
Abstract: Automatic reusability appraisal is helpful in
evaluating the quality of developed or developing reusable software
components and in identification of reusable components from
existing legacy systems; that can save cost of developing the
software from scratch. But the issue of how to identify reusable
components from existing systems has remained relatively
unexplored. In this research work, structural attributes of software
components are explored using software metrics and quality of the
software is inferred by different Neural Network based approaches,
taking the metric values as input. The calculated reusability value
enables to identify a good quality code automatically. It is found that
the reusability value determined is close to the manual analysis used
to be performed by the programmers or repository managers. So, the
developed system can be used to enhance the productivity and
quality of software development.
Abstract: The objective of this research was to investigate biodegradation of water hyacinth (Eichhornia crassipes) to produce bioethanol using dilute-acid pretreatment (1% sulfuric acid) results in high hemicellulose decomposition and using yeast (Pachysolen tannophilus) as bioethanol producing strain. A maximum ethanol yield of 1.14g/L with coefficient, 0.24g g-1; productivity, 0.015g l-1h-1 was comparable to predicted value 32.05g/L obtained by Central Composite Design (CCD). Maximum ethanol yield coefficient was comparable to those obtained through enzymatic saccharification and fermentation of acid hydrolysate using fully equipped fermentor. Although maximum ethanol concentration was low in lab scale, the improvement of lignocellulosic ethanol yield is necessary for large scale production.
Abstract: Software development has experienced remarkable progress in the past decade. However, due to the rising complexity and magnitude of the project the development productivity has not been consistently improved. By analyzing the latest ISBSG data repository with 4106 projects, we discovered that software development productivity has actually undergone irregular variations between the years 1995 and 2005. Considering the factors significant to the productivity, we found its variations are primarily caused by the variations of average team size and the unbalanced uses of the less productive language 3GL.
Abstract: The past decade has seen enormous growth in the amount of software produced. However, given the ever increasing complexity of the software being developed and the concomitant rise in the typical project size, managers are becoming increasingly aware of the importance of issues that influence the productivity levels of the project teams involved. By analyzing the latest release of ISBSG data repository, we report on the factors found to significantly influence the productivity among which average team size and language type are the two most essential ones. Building on this we present an original model for evaluating the potential productivity during the project planning stage.
Abstract: Work ethic and labour productivity issues are
extremely important for any society. It has been long proven by the
global practice and various scholars that the country promoting the
labour has always been way forward from the other countries. This
paper studies the thoughts suggested by M.Weber, Confucius, Lee
Kuan Yew, Mahathir Mohammad and other prominent thinkers
concerning the issues of work ethics and labour productivity. The
article analyzes why developed nations are way more advanced in
their development compared to other nations.
Abstract: With the advent of new technologies, factors related to
mental health in e-workspaces are taken into consideration more than
ever. Studies have revealed that one of the factors affecting the
productivity of employees in an organization is occupational stress.
Another influential factor is quality of work life which is important in
the improvement of work environment conditions and organizational
efficiency. In order to uncover the quality of work life level and to
investigate the impact of occupational stress on quality of work life
among information technology employees in Iran, a cross-sectional
study design was applied and data were gathered using a
questionnaire validated by a group of experts. The results of the study
showed that information technology staffs have average level of both
occupational stress and quality of work life. Furthermore, it was
found that occupational stress has a negative impact on quality of
work life. In addition, the same results were observed for role
ambiguity, role conflict, role under-load, work-pace, work
repetitiveness and tension toward quality of work life. No significant
relation was found between role overload and quality of work life.
Finally, directions for future research are proposed and discussed.
Abstract: Corporate identity, which has several advantages such
that the employees become integrated with their corporations,
corporation is distinguished from its competitors and it is recognized
by the masses, is the total of the distinctive corporate features that
and corporation has. That the information takes part in production as
a more important component than labor and capital has required that
the corporations are reorganized as information-based. Therefore,
information and its management have reached a basic and prevalent
position in having sustainable competitive advantage. Thanks to the
information management which regulates the information and makes
it reachable and available, information will be produced in line with a
specific purpose in the corporations and be used in all the corporate
processes. As an auxiliary power for increase in the economic
potential, efficiency and productivity of the corporation, corporate
identity consists of four components. These are corporate philosophy,
corporate design, corporate behavior and corporate communication.
In this study, the effects of the information management on corporate
identity are discussed from the point of these four elements.
Abstract: Earthmoving operations are a major part of many
construction projects. Because of the complexity and fast-changing
environment of such operations, the planning and estimating are
crucial on both planning and operational levels. This paper presents
the framework ofa microscopic discrete-event simulation system for
modeling earthmoving operations and conducting productivity
estimations on an operational level.A prototype has been developed
to demonstrate the applicability of the proposed framework, and this
simulation system is presented via a case study based on an actual
earthmoving project. The case study shows that the proposed
simulation model is capable of evaluating alternative operating
strategies and resource utilization at a very detailed level.
Abstract: This paper and its companion (Part 2) deal with
modeling and optimization of two NP-hard problems in production
planning of flexible manufacturing system (FMS), part type selection
problem and loading problem. The part type selection problem and
the loading problem are strongly related and heavily influence the
system-s efficiency and productivity. The complexity of the problems
is harder when flexibilities of operations such as the possibility of
operation processed on alternative machines with alternative tools are
considered. These problems have been modeled and solved
simultaneously by using real coded genetic algorithms (RCGA)
which uses an array of real numbers as chromosome representation.
These real numbers can be converted into part type sequence and
machines that are used to process the part types. This first part of the
papers focuses on the modeling of the problems and discussing how
the novel chromosome representation can be applied to solve the
problems. The second part will discuss the effectiveness of the
RCGA to solve various test bed problems.
Abstract: Improving performance measures in the construction
processes has been a major concern for managers and decision
makers in the industry. They seek for ways to recognize the key
factors which have the largest effect on the process. Identifying such
factors can guide them to focus on the right parts of the process in
order to gain the best possible result. In the present study design of
experiment (DOE) has been applied to a computer simulation model
of brick laying process to determine significant factors while
productivity has been chosen as the response of the experiment. To
this end, four controllable factors and their interaction have been
experimented and the best factor level has been calculated for each
one. The results indicate that three factors, namely, labor of brick,
labor of mortar and inter arrival time of mortar along with interaction
of labor of brick and labor of mortar are significant.
Abstract: Lean manufacturing is a production philosophy made
popular by Toyota Motor Corporation (TMC). It is globally known as
the Toyota Production System (TPS) and has the ultimate aim of
reducing cost by thoroughly eliminating wastes or muda. TPS
embraces the Just-in-time (JIT) manufacturing; achieving cost
reduction through lead time reduction. JIT manufacturing can be
achieved by implementing Pull system in the production.
Furthermore, TPS aims to improve productivity and creating
continuous flow in the production by arranging the machines and
processes in cellular configurations. This is called as Cellular
Manufacturing Systems (CMS). This paper studies on integrating the
CMS with the Pull system to establish a Big Island-Pull system
production for High Mix Low Volume (HMLV) products in an
automotive component industry. The paper will use the build-in JIT
system steps adapted from TMC to create the Pull system production
and also create a shojinka line which, according to takt time, has the
flexibility to adapt to demand changes simply by adding and taking
out manpower. This will lead to optimization in production.
Abstract: Industrial robots become useless without end-effectors
that for many instances are in the form of friction grippers.
Commonly friction grippers apply frictional forces to different
objects on the basis of programmers- experiences. This puts a
limitation on the effectiveness of gripping force that may result in
damaging the object. This paper describes various stages of design
and development of a low cost sensor-based robotic gripper that
would facilitate the task of applying right gripping forces to different
objects. The gripper is also equipped with range sensors in order to
avoid collisions of the gripper with objects. It is a fully functional
automated pick and place gripper which can be used in many
industrial applications. Yet it can also be altered or further developed
in order to suit a larger number of industrial activities. The current
design of gripper could lead to designing completely automated robot
grippers able to improve the efficiency and productivity of industrial
robots.
Abstract: The chatter is one of the major limitations of the productivity in the ball end milling process. It affects the surface roughness, the dimensional accuracy and the tool life. The aim of this research is to propose the new system to detect the chatter during the ball end milling process by using the wavelet transform. The proposed method is implemented on the 5-axis CNC machining center and the new three parameters are introduced from three dynamic cutting forces, which are calculated by taking the ratio of the average variances of dynamic cutting forces to the absolute variances of themselves. It had been proved that the chatter can be easier to detect during the in-process cutting by using the new parameters which are proposed in this research. The experimentally obtained results showed that the wavelet transform can provide the reliable results to detect the chatter under various cutting conditions.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece with copper tools are being optimized
according to its individual machining characteristic i.e. material
removal rate (MRR). Lower MRR during EDM machining process
may decrease its- machining productivity. Hence, the quality
characteristic for MRR is set to higher-the-better to achieve the
optimum machining productivity. Taguchi method has been used
for the construction, layout and analysis of the experiment for each
of the machining characteristic for the MRR. The use of Taguchi
method in the experiment saves a lot of time and cost of preparing
and machining the experiment samples. Therefore, an L18
Orthogonal array which was the fundamental component in the
statistical design of experiments has been used to plan the
experiments and Analysis of Variance (ANOVA) is used to
determine the optimum machining parameters for this machining
characteristic. The control parameters selected for this
optimization experiments are polarity, pulse on duration, discharge
current, discharge voltage, machining depth, machining diameter
and dielectric liquid pressure. The result had shown that the higher
the discharge voltage, the higher will be the MRR.
Abstract: This paper is part of an ongoing research on the
development of systemic maintenance management model Malaysian
university buildings. In order to achieve this aim, there is a need to
develop a performance model against which services are measure.
Measuring performance is a significant part of maintenance
management service delivery. Maintenance organization needs to
know where they are in order to provide user-driven services and to
enhance productivity. The aim of this paper is to formulate a
template or model for university maintenance organization in
Malaysia. The model is based on literature review and survey
questionnaire and has been validated. Through grounded theory, this
paper developed a 8 points matrix for the university maintenance
organizations for measuring and improving their service delivery.
The potential of the model is guide and assists towards providing
value added service delivery through initiating maintenance
according to user value system rather than on the condition of the
building.
Abstract: Many companies have excel, it is economy and well perform to use in material requirement planning (MRP) on excel. For several products, it, however, is complex problem to link the relationship between the tables of products because the relationship depends on bill of material (BOM). This paper presents algorithm to create MRP on excel, and links relationship between tables. The study reveals MRP that is created by the algorithm which is easier and faster than MRP that created by human. By this technique, MRP on excel might be good ways to improve a productivity of companies.
Abstract: In this study, lipase production has been investigated
using submerge fermentation by Aspergillus niger in Kilka fish oil as
main substrate. The Taguchi method with an L9 orthogonal array
design was used to investigate the effect of parameters and their
levels on lipase productivity. The optimum conditions for Kilka fish
oil concentration, incubation temperature and pH were obtained 3
gr./ml 35°C and 7, respectively. The amount of lipase activity in
optimum condition was obtained 4.59IU/ml. By comparing this
amount with the amount of productivity in the olive oil medium
based on the cost of each medium, it was that using Kilka fish oil is
84% economical. Therefore Kilka fish oil can be used as an
economical and suitable substrate in the lipase production and
industrial usages.
Abstract: This paper aims at to develop a robust optimization methodology for the mechatronic modules of machine tools by considering all important characteristics from all structural and control domains in one single process. The relationship between these two domains is strongly coupled. In order to reduce the disturbance caused by parameters in either one, the mechanical and controller design domains need to be integrated. Therefore, the concurrent integrated design method Design For Control (DFC), will be employed in this paper. In this connect, it is not only applied to achieve minimal power consumption but also enhance structural performance and system response at same time. To investigate the method for integrated optimization, a mechatronic feed drive system of the machine tools is used as a design platform. Pro/Engineer and AnSys are first used to build the 3D model to analyze and design structure parameters such as elastic deformation, nature frequency and component size, based on their effects and sensitivities to the structure. In addition, the robust controller,based on Quantitative Feedback Theory (QFT), will be applied to determine proper control parameters for the controller. Therefore, overall physical properties of the machine tool will be obtained in the initial stage. Finally, the technology of design for control will be carried out to modify the structural and control parameters to achieve overall system performance. Hence, the corresponding productivity is expected to be greatly improved.
Abstract: The selection for plantation of a particular type of
mustard plant depending on its productivity (pod yield) at the stage
of maturity. The growth of mustard plant dependent on some
parameters of that plant, these are shoot length, number of leaves,
number of roots and roots length etc. As the plant is growing, some
leaves may be fall down and some new leaves may come, so it can
not gives the idea to develop the relationship with the seeds weight at
mature stage of that plant. It is not possible to find the number of
roots and root length of mustard plant at growing stage that will be
harmful of this plant as roots goes deeper to deeper inside the land.
Only the value of shoot length which increases in course of time can
be measured at different time instances. Weather parameters are
maximum and minimum humidity, rain fall, maximum and minimum
temperature may effect the growth of the plant. The parameters of
pollution, water, soil, distance and crop management may be
dominant factors of growth of plant and its productivity. Considering
all parameters, the growth of the plant is very uncertain, fuzzy
environment can be considered for the prediction of shoot length at
maturity of the plant. Fuzzification plays a greater role for
fuzzification of data, which is based on certain membership
functions. Here an effort has been made to fuzzify the original data
based on gaussian function, triangular function, s-function,
Trapezoidal and L –function. After that all fuzzified data are
defuzzified to get normal form. Finally the error analysis
(calculation of forecasting error and average error) indicates the
membership function appropriate for fuzzification of data and use to
predict the shoot length at maturity. The result is also verified using
residual (Absolute Residual, Maximum of Absolute Residual, Mean
Absolute Residual, Mean of Mean Absolute Residual, Median of
Absolute Residual and Standard Deviation) analysis.