Abstract: In this paper, an Infinite Impulse Response (IIR) filter
has been designed and simulated on an Field Programmable Gate
Arrays (FPGA). The implementation is based on Multiply Add and
Accumulate (MAC) algorithm which uses multiply operations for
design implementation. Parallel Pipelined structure is used to
implement the proposed IIR Filter taking optimal advantage of the
look up table of target device. The designed filter has been
synthesized on Digital Signal Processor (DSP) slice based FPGA to
perform multiplier function of MAC unit. The DSP slices are useful
to enhance the speed performance. The proposed design is simulated
with Matlab, synthesized with Xilinx Synthesis Tool, and
implemented on FPGA devices. The Virtex 5 FPGA based design can
operate at an estimated frequency of 81.5 MHz as compared to 40.5
MHz in case of Spartan 3 ADSP based design. The Virtex 5 based
implementation also consumes less slices and slice flip flops of target
FPGA in comparison to Spartan 3 ADSP based implementation to
provide cost effective solution for signal processing applications.
Abstract: Polymeric composites are being increasingly used as
repair material for repairing critical infrastructures such as building,
bridge, pressure vessel, piping and pipeline. Technique in repairing
damaged pipes is one of the major concerns of pipeline owners.
Considerable researches have been carried out on the repair of
corroded pipes using composite materials. This article attempts a
short review of the subject matter to provide insight into various
techniques used in repairing corroded pipes, focusing on a wide range
of composite repair systems. These systems including pre-cured
layered, flexible wet lay-up, pre-impregnated, split composite sleeve
and flexible tape systems. Both advantages and limitations of these
repair systems were highlighted. Critical technical aspects have been
discussed through the current standards and practices. Research gaps
and future study scopes in achieving more effective design
philosophy are also presented.
Abstract: This experimental study consists of a characterization
of epoxy grout where an amount of 2% of graphene nanoplatelets
particles were added to commercial epoxy resin to evaluate their
behavior regarding neat epoxy resin. Compressive tests, tensile tests
and flexural tests were conducted to study the effect of graphene
nanoplatelets on neat epoxy resin. By comparing graphene-based and
neat epoxy grout, there is no significant increase of strength due to
weak interface in the graphene nanoplatelets/epoxy composites.
From this experiment, the tension and flexural strength of graphenebased
epoxy grouts is slightly lower than ones of neat epoxy grout.
Nevertheless, the addition of graphene has produced more consistent
results according to a smaller standard deviation of strength.
Furthermore, the graphene has also improved the ductility of the
grout, hence reducing its brittle behaviour. This shows that the
performance of graphene-based grout is reliably predictable and able
to minimise sudden rupture. This is important since repair design of
damaged pipeline is of deterministic nature.
Abstract: Carbon dioxide is one of the major greenhouse gas
(GHG) contributors. It is an obligation of the industry to reduce the
amount of carbon dioxide emission to the acceptable limits.
Tremendous research and studies are reported in the past and still the
quest to find the suitable and economical solution of this problem
needed to be explored in order to develop the most plausible absorber
for carbon dioxide removal. Amino acids can be potential alternate
solvents for carbon dioxide capture from gaseous streams. This is due
to its ability to resist oxidative degradation, low volatility and its
ionic structure. In addition, the introduction of promoter-like
piperazine to amino acid helps to further enhance the solubility. In
this work, the effect of piperazine on thermo physical properties and
solubility of β-Alanine aqueous solutions were studied for various
concentrations. The measured physicochemical properties data was
correlated as a function of temperature using least-squares method
and the correlation parameters are reported together with it respective
standard deviations. The effect of activator piperazine on the CO2
loading performance of selected amino acid under high-pressure
conditions (1bar to 10bar) at temperature range of (30 to 60)oC was
also studied. Solubility of CO2 decreases with increasing temperature
and increases with increasing pressure. Quadratic representation of
solubility using Response Surface Methodology (RSM) shows that
the most important parameter to optimize solubility is system
pressure. The addition of promoter increases the solubility effect of
the solvent.
Abstract: Production fluids are transported from the platform to
tankers or process facilities through transfer pipelines. Water being
one of the heavier phases tends to settle at the bottom of pipelines
especially at low flow velocities and this has adverse consequences
for pipeline integrity. On restart after a shutdown, this could result in
corrosion and issues for process equipment, thus the need to have the
heavier liquid dispersed into the flowing lighter fluid. This study
looked at the flow regime of low water cut and low flow velocity oil
and water flow using conductive film thickness probes in a large
diameter 4-inch pipe to obtain oil and water interface height and the
interface structural velocity. A wide range of 0.1–1.0 m/s oil and
water mixture velocities was investigated for 0.5–5% water cut. Two
fluid model predictions were used to compare with the experimental
results.
Abstract: In the vicinity of red sea about 15 fungi species were
isolated from oil contaminated sites. On the basis of aptitude to
degrade the crude oil and DCPIP assay, two fungal isolates were
selected amongst 15 oil degrading strains. Analysis of ITS-1, ITS-2
and amplicon pyrosequencing studies of fungal diversity revealed
that these strains belong to Penicillium and Aspergillus species. Two
strains that proved to be the most efficient in degrading crude oil was
Aspergillus niger (54%) and Penicillium commune (48%) Subsequent
to two weeks of cultivation in BHS medium the degradation rate
were recorded by using spectrophotometer and GC-MS. Hence, it is
cleared that these fungal strains has capability of degradation and can
be utilize for cleaning the Saudi Arabian environment.
Abstract: This study presents experimental and optimization of
nanoparticle mass concentration and heat input based on the total
thermal resistance (Rth) of loop heat pipe (LHP), employed for PCCPU
cooling. In this study, silica nanoparticles (SiO2) in water with
particle mass concentration ranged from 0% (pure water) to 1% is
considered as the working fluid within the LHP. The experimental
design and optimization is accomplished by the design of
experimental tool, Response Surface Methodology (RSM). The
results show that the nanoparticle mass concentration and the heat
input have significant effect on the Rth of LHP. For a given heat
input, the Rth is found to decrease with the increase of the
nanoparticle mass concentration up to 0.5% and increased thereafter.
It is also found that the Rth is decreased when the heat input is
increased from 20W to 60W. The results are optimized with the
objective of minimizing the Rth, using Design-Expert software, and
the optimized nanoparticle mass concentration and heat input are
0.48% and 59.97W, respectively, the minimum thermal resistance
being 2.66 (ºC/W).
Abstract: This investigation is focused on using of Mon dance
in Pathum Thani Province’s tradition and has the following
objectives: 1) to study the background of Mon dance in Pathum
Thani Province; 2) to study Mon dance in Pathum Thani Province;
and 3) to study of using Mon dance in Pathum Thani province’s
tradition. This qualitative research was conducted in Pathum Thani
province (in the central of Thailand). Data was collected from
documentary study and field data by means of observation, interview,
and group discussion. Workshops were also held with a total of 100
attendees, comprised of 20 key informants, 40 casual informants and
40 general informants. Data was validated using the triangulation
technique and the findings are presented using the descriptive
analysis. The results of the study show that the historical background
of Mon dance in Pathum Thani Province initiated during the war
evacuation from Martaban (south of Burma) to settle down in Sam
Khok, Pathum Thani Province in Ayutthaya period to Rattanakosin.
The study found that Mon dance typically consists of 12-13 dancing
process. The melodies have 12-13 songs. Piphat Mon (Mon
traditional music ensemble) is used in the performance. Performers
are dressed in Mon traditional costumes. The performers are 6-12
women and depending on the employer’s demands. Length of the
performance varies from the duration of music orchestration. Rituals
and customs performed are paying homage to teachers before the
performance. The offerings are composed of flowers, incense sticks,
candles, money gifts which are well arranged on a tray with pedestal,
and also liquors, tobaccos and pure water for asking propitiousness.
For the use of Mon dance in Pathum Thani Province’s tradition, it is
found that the dance is commonly performed in the funeral
ceremonial tradition at present because the physical postures of the
performance are considered graceful and exquisite. In addition, as for
its value, it has long been believed since the ancient times that Mon
dance was a sacred thing considered as the dignity and glorification
especially for funeral ceremonies of priest or royal hierarchy classes.
However, Mon dance has continued to be used in the traditions
associated with Mon people activities in Pathum Thani Province for
instance customary welcome for honor guest and Songkran festival.
Abstract: Kurtbogazi Dam has gained special meaning for Ankara, Turkey for the last decade due to the rapid depletion of nearby resources of drinking water. In this study, the results of the analyses of Kurtbogazi Dam outlet water and the rivers flowing into the Kurtbogazi Dam were discussed for the period of last five years between 2008 and 2012. Some physical and chemical properties (pH, temperature, biochemical oxygen demand (BOD5), nitrate, phosphate and chlorine) of these water resources were evaluated. They were classified according to the Council Directive (75/440/EEC). Moreover, the properties of these surface waters were assessed to determine the quality of water for drinking and irrigation purposes using Piper, US Salinity Laboratory and Wilcox diagrams. The results showed that all the water resources are acceptable level as surface water except for Pazar Stream in terms of ortho-phosphate and BOD5 concentration for 2008.
Abstract: The current study focuses on the seismic design of
offshore pipelines against active faults. After an extensive literature
review of the provisions of the seismic norms worldwide and of the
available analytical methods, the study simulates numerically
(through finite-element modeling and strain-based criteria) the
distress of offshore pipelines subjected to PGDs induced by active
normal and reverse seismic faults at the seabed. Factors, such as the
geometrical properties of the fault, the mechanical properties of the
ruptured soil formations, and the pipeline characteristics, are
examined. After some interesting conclusions regarding the seismic
vulnerability of offshore pipelines, potential cost-effective mitigation
measures are proposed taking into account constructability issues.
Abstract: A large variety of pipe flange is required in marine
and construction industry. Pipe flanges are usually welded or screwed
to the pipe end and are connected with bolts. This approach is very
simple and widely used for a long time; however, it results in high
development cost and low productivity, and the productions made by
this approach usually have safety problem at the welding area. In this
research, a new approach of forming pipe flange based on cold
forging and floating die concept is presented. This innovative
approach increases the effectiveness of the material usage and save
the time cost compared with conventional welding method. To ensure the dimensional accuracy of the final product, the finite
element analysis (FEA) was carried out to simulate the process of
cold forging, and the orthogonal experiment methods were used to
investigate the influence of four manufacturing factors (pin die angle,
pipe flange angle, rpm, pin die distance from clamp jig) and predicted
the best combination of them. The manufacturing factors were
obtained by numerical and experimental studies and it shows that the
approach is very useful and effective for the forming of pipe flange,
and can be widely used later.
Abstract: This paper presents the result of an experimental
investigation regarding the use of Fe2O3 nanoparticles added to
kerosene as a working fluid, under magnetic field for Copper
Oscillating Heat pipe with inclination angle of 0°(horizontal), 15°,
30°,45°, 60°,75° and 90° (vertical). The following were examined;
measure the temperature distribution and heat transfer rate on
Oscillating Heat Pipe (OHP), with magnetic field under different
angles. Results showed that the addition of Fe2O3 nanoparticles under
magnetic field improved thermal performance of OHP especially in
75°.
Abstract: Urinary Tract Infections are considered as one of the
most common bacterial infections with an estimated annual global
incidence of 150 million. Antimicrobial drug resistance is one of the
major threats due to wide spread usage of uncontrolled antibiotics. In
this study, a total number of 9149 urine samples were collected from
R.H Patiala and processed in the Department of Microbiology G. M.
C Patiala (January 2013 to December 2013). Urine samples were
inoculated on MacConkey’s and blood agar plates and incubated at
370C for 24 hrs. The organisms were identified by colony characters,
Gram’s staining, and biochemical reactions. Antimicrobial
susceptibility of the isolates was determined against various
antimicrobial agents (Hi – Media Mumbai India) by Kirby Bauer
DISK diffusion method on Muller Hinton agar plates. Maximum patients were in the age group of 21-30 yrs followed by
31-40 yrs. Males (34%) are less prone to urinary tract infections than
females (66%). Culture was positive in 25% of the samples.
Escherichia coli was the most common isolate 60.3% followed by
Klebsiella pneumoniae 13.5%, Proteus spp. 9% and Staphylococcus
aureus 7.6%. Most of the urinary isolates were sensitive to,
carbepenems, Aztreonam, Amikacin, and Piperacillin + Tazobactum.
All the isolates showed a good sensitivity towards Nitrofurantoin
(82%). ESBL production was found to be 70.6% in Escherichia coli
and 29.4% in Klebsiella pneumonia. Susceptibility of ESBL
producers to Imipenem, Nitrofurantoin and Amikacin were found to
be 100%, 76%, and 75% respectively. Uropathogens are increasingly
showing resistance to many antibiotics making empiric management
of outpatient UTIs challenging. Ampicillin, Cotrimoxazole and
Ciprofloxacin should not be used in empiric treatment. Nitrofurantoin
could be used in lower urinary tract infection. Knowledge of
uropathogens and their antimicrobial susceptibility pattern in a
geographical region will help in appropriate and judicious antibiotic
usage in a health care setup.
Abstract: In this study, failure analysis of pipe system at a micro
hydroelectric power plant is investigated. Failure occurred at the pipe
system in the powerhouse during shut down operation of the water
flow by a valve. This locking had caused a sudden shock wave, also
called “Water-hammer effect”, resulting in noise and inside pressure
increase. After visual investigation of the effect of the shock wave on
the system, a circumference crack was observed at the pipe flange
weld region. To establish the reason for crack formation, calculations
of pressure and stress values at pipe, flange and welding seams were
carried out and concluded that safety factor was high (2.2), indicating
that no faulty design existed. By further analysis, pipe system and
hydroelectric power plant was examined. After observations it is
determined that the plant did not include a ventilation nozzle (air
trap), that prevents the system of sudden pressure increase inside the
pipes which is caused by water-hammer effect. Analyses were carried
out to identify the influence of water-hammer effect on inside
pressure increase and it was concluded that, according Jowkowsky’s
equation, shut down time is effective on inside pressure increase. The
valve closing time was uncertain but by a shut down time of even one
minute, inside pressure would increase by 7.6 bar (working pressure
was 34.6 bar). Detailed investigations were also carried out on the
assembly of the pipe-flange system by considering technical
drawings. It was concluded that the pipe-flange system was not
installed according to the instructions. Two of five weld seams were
not applied and one weld was carried out faulty. This incorrect and
inadequate weld seams resulted in; insufficient connection of the pipe
to the flange constituting a strong notch effect at weld seam regions,
increase in stress values and the decrease of strength and safety
factor.
Abstract: Erosion and abrasion are wear mechanisms reducing
the lifetime of machine elements like valves, pump and pipe systems.
Both wear mechanisms are acting at the same time, causing a
“Synergy” effect, which leads to a rapid damage of the surface.
Different parameters are effective on erosive abrasive wear rate. In
this study effect of particle impact angle on wear rate and wear
mechanism of ductile and brittle materials was investigated. A new
slurry pot was designed for experimental investigation. As abrasive
particle, silica sand was used. Particle size was ranking between 200-
500 μm. All tests were carried out in a sand-water mixture of 20%
concentration for four hours. Impact velocities of the particles were
4.76 m/s. As ductile material steel St 37 with Vickers Hardness
Number (VHN) of 245 and quenched St 37 with 510 VHN was used
as brittle material. After wear tests, morphology of the eroded
surfaces were investigated for better understanding of the wear
mechanisms acting at different impact angles by using Scanning
Electron Microscope. The results indicated that wear rate of ductile
material was higher than brittle material. Maximum wear rate was
observed by ductile material at a particle impact angle of 300 and
decreased further by an increase in attack angle. Maximum wear rate
by brittle materials was by impact angle of 450 and decreased further
up to 900. Ploughing was the dominant wear mechanism by ductile
material. Microcracks on the surface were detected by ductile
materials, which are nucleation centers for crater formation. Number
of craters decreased and depth of craters increased by ductile
materials by attack angle higher than 300. Deformation wear
mechanism was observed by brittle materials. Number and depth of
pits decreased by brittle materials by impact angles higher than 450.
At the end it is concluded that wear rate could not be directly related
to impact angle of particles due to the different reaction of ductile and
brittle materials.
Abstract: The fuel potential of six tropical hardwood species
namely: Triplochiton scleroxylon, Ceiba pentandra, Aningeria
robusta, Terminalia superba, Celtis mildbreadii and Piptadenia
africana were studied. Properties studied included species density,
gross calorific value, volatile matter, ash content, organic carbon and
elemental composition. Fuel properties were determined using
standard laboratory methods. The result indicates that the gross
calorific value (GCV) of the species ranged from 20.16 to 22.22
MJ/kg and they slightly varied from each other. Additionally, the
GCV of the biomass materials were higher than that of other biomass
materials like; wheat straw, rice straw, maize straw and sugar cane.
The ash and volatile matter content varied from 0.6075 to 5.0407%,
and 75.23% to 83.70% respectively. The overall rating of the
properties of the six biomass materials suggested that Piptadenia
africana has the best fuel property to be used as briquettes and
Aningeria robusta the worse. This study therefore suggests that a
holistic assessment of a biomass material needs to be done before
selecting it for fuel purpose.
Abstract: The present work is aimed at examining carbon steel
oil pipelines corrosion using three natural extracts (Eruca Sativa,
Rosell and Mango peels) that are used as inhibitors of different
concentrations ranging from 0.05-0.1wt. %. Two sulphur compounds
are used as corrosion mediums. Weight loss method was used for
measuring the corrosion rate of the carbon steel specimens immersed
in technical white oil at 100ºC at various time intervals in absence
and presence of the two sulphur compounds. The corroded specimens
are examined using the chemical wear test, scratch test and hardness
test. The scratch test is carried out using scratch loads from 0.5 Kg to
2.0 Kg. The scratch width is obtained at various scratch load and test
conditions. The Brinell hardness test is carried out and investigated
for both corroded and inhibited specimens. The results showed that
three natural extracts can be used as environmentally friendly
corrosion inhibitors.
Abstract: In order to obtain efficient pollutants removal in
small-scale wastewater treatment plants, uniform water flow has to be
achieved. The experimental setup, designed for treating high-load
wastewater (leachate), consists of two aerobic biological reactors and
a lamellar settler. Both biological tanks were aerated by using three
different types of aeration systems - perforated pipes, membrane air
diffusers and tube ceramic diffusers. The possibility of homogenizing
the water mass with each of the air diffusion systems was evaluated
comparatively. The oxygen concentration was determined by optical
sensors with data logging. The experimental data was analyzed
comparatively for all three different air dispersion systems aiming to
identify the oxygen concentration variation during different
operational conditions. The Oxygenation Capacity was calculated for
each of the three systems and used as performance and selection
parameter. The global mass transfer coefficients were also evaluated
as important tools in designing the aeration system. Even though
using the tubular porous diffusers leads to higher oxygen
concentration compared to the perforated pipe system (which
provides medium-sized bubbles in the aqueous solution), it doesn’t
achieve the threshold limit of 80% oxygen saturation in less than 30
minutes. The study has shown that the optimal solution for the
studied configuration was the radial air diffusers which ensure an
oxygen saturation of 80% in 20 minutes. An increment of the values
was identified when the air flow was increased.
Abstract: In this paper comprehensive studies have been carried
out for the design optimization of a waste heat recovery system for
effectively utilizing the domestic air conditioner heat energy for
producing hot water. Numerical studies have been carried for the
geometry optimization of a waste heat recovery system for domestic
air conditioners. Numerical computations have been carried out using
a validated 2d pressure based, unsteady, 2nd-order implicit, SST k-ω
turbulence model. In the numerical study, a fully implicit finite
volume scheme of the compressible, Reynolds-Averaged, Navier-
Stokes equations is employed. At identical inflow and boundary
conditions various geometries were tried and effort has been taken for
proposing the best design criteria. Several combinations of pipe line
shapes viz., straight and spiral with different number of coils for the
radiator have been attempted and accordingly the design criteria has
been proposed for the waste heat recovery system design. We have
concluded that, within the given envelope, the geometry optimization
is a meaningful objective for getting better performance of waste heat
recovery system for air conditioners.
Abstract: The development of electric vehicle batteries have
resulted in very high energy density lithium-ion batteries. However,
this progress is accompanied by the risk of thermal runaway, which
can result in serious accidents. Heat pipes are heat exchangers that
are suitable to be applied in electric vehicle battery thermal
management for their lightweight, compact size and do not require
external power supply. This paper aims to examine experimentally a
Flat Plate Loop Heat Pipe (FPLHP) performance as a heat exchanger
in thermal management system of lithium-ion battery for electric
vehicle application. The heat generation of the battery was simulated
using a cartridge heater. Stainless steel screen mesh was used as the
capillary wick. Distilled water, alcohol and acetone were used as
working fluids with a filling ratio of 60%. It was found that acetone
gives the best performance that produces thermal resistance of 0.22
W/°C with 50°C evaporator temperature at heat flux load of 1.61
W/cm2.