Abstract: Synthesis of gold nanoparticles has attracted much
attention since the pioneering discovery of the high catalytic activity
of supported gold nanoparticles in the reaction of CO oxidation at
low temperature. In this research field, we used Na-montmorillonite
for gold nanoparticles stabilization; various gold loading percentage
1, 2 and 5% were used for gold nanoparticles preparation. The gold
nanoparticles were obtained using chemical reduction method using
NaBH4 as reductant agent. The obtained gold nanoparticles stabilized
in Na-montmorillonite were used as catalysts for the reduction of 4-
nitrophenol to aminophenol with sodium borohydride at room
temperature. The UV-Vis results confirmed directly the gold
nanoparticles formation. The XRD and N2 adsorption results showed
the formation of gold nanoparticles in the pores of montmorillonite
with an average size of 5 nm obtained on samples with 2% gold
loading percentage. The gold particles size increased with the
increase of gold loading percentage. The reduction reaction of 4-
nitrophenol into 4-aminophenol with NaBH4 catalyzed by Au-Namontmorillonite
catalyst exhibits remarkably a high activity; the
reaction was completed within 9 min for 1%Au-Na-montmorillonite
and within 3 min for 2%Au-Na-montmorillonite.
Abstract: Biodiesel is one of the alternative fuels that promising
for substituting petro diesel as energy source which is advantage on
sustainability and ecofriendly. Due to the raw material that tend to
decompose during storage, biodiesel also have the same characteristic
that tend to decompose and formed higher acid value which is the
result of oxidation to double bond on a chain of ester. Decomposition of biodiesel due to oxidation reaction could
prevent by introduce a small amount of antioxidant. The origin of raw
materials and the process for producing biodiesel will determine the
effectiveness of antioxidant. The quality degradation on biodiesel
could evaluate by measuring iodine value and acid number of
biodiesel. Biodiesel made from high fatty acid Jatropha curcas oil by using
esterification and transesterification process will stand on the quality
by introduce 90 ppm pyrogallol powder on the biodiesel, which could
increase Induction period time from 2 hours to more than 6 hours in
rancimat test evaluation.
Abstract: The goal of this experiment is to evaluate the
effectiveness of different leachate pre-treatment options in terms of
COD and ammonia removal. This research focused on the evaluation
of physical-chemical methods for pre-treatment of leachate that
would be effective and rapid in order to satisfy the requirements of
the sewer discharge by-laws. The four pre-treatment options
evaluated were: air stripping, chemical coagulation, electrocoagulation
and advanced oxidation with sodium ferrate. Chemical
coagulation reported the best COD removal rate at 43%, compared to
18% for both air stripping and electro-coagulation, and 20% for
oxidation with sodium ferrate. On the other hand, air stripping was
far superior to the other treatment options in terms of ammonia
removal with 86%. Oxidation with sodium ferrate reached only 16%,
while chemical coagulation and electro-coagulation removed less
than 10%. When combined, air stripping and chemical coagulation
removed up to 50% COD and 85% ammonia.
Abstract: In recent research copper and manganese systems
were found to be the most active in CO and organic compounds
oxidation among the base catalysts. The mixed copper manganese
oxide has been widely studied in oxidation reactions because of their
higher activity at low temperatures in comparison with single oxide
catalysts. The results showed that the formation of spinel
CuxMn3−xO4 in the oxidized catalyst is responsible for the activity
even at room temperature. That is why the most of the investigations
are focused on the hopcalite catalyst (CuMn2O4) as the best coppermanganese
catalyst. Now it’s known that this is true only for CO
oxidation, but not for mixture of CO and VOCs. The purpose of this
study is to investigate the alumina supported copper-manganese
catalysts with different Cu/Mn molar ratio in terms of oxidation of
CO, methanol and dimethyl ether. The catalysts were prepared by impregnation of γ-Al2O3 with
copper and manganese nitrates and the catalytic activity
measurements were carried out in two stage continuous flow
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions closest possible to the industrial. Gas
mixtures on the input and output of the reactor were analyzed with a
gas chromatograph, equipped with FID and TCD detectors. The
texture characteristics were determined by low-temperature (- 196oС)
nitrogen adsorption in a Quantachrome Instruments NOVA 1200e
(USA) specific surface area & pore analyzer. Thermal, XRD and
TPR analyses were performed. It was established that the active component of the mixed Cu-
Mn/γ–alumina catalysts strongly depends on the Cu/Mn molar ratio.
Highly active alumina supported Cu-Mn catalysts for CO, methanol
and DME oxidation were synthesized. While the hopcalite is the best
catalyst for CO oxidation, the best compromise for simultaneous
oxidation of all components is the catalyst with Cu/Mn molar ratio
1:5.
Abstract: Due to the resultant leachate from waste
decomposition in landfills has polluter potential hundred times
greater than domestic sewage, this is considered a problem related to
the depreciation of environment requiring pre-disposal treatment.In
seeking to improve this situation, this project proposes the treatment
of landfill leachate using natural fibers intercropped with advanced
oxidation processes. The selected natural fibers were palm, coconut
and banana fiber.These materials give sustainability to the project
because, besides having adsorbent capacity, are often part of waste
discarded. The study was conducted in laboratory scale.In trials, the
effluents were characterized as Chemical Oxygen Demand (COD),
Turbidity and Color. The results indicate that is technically
promising since that there were extremely oxidative conditions, the
use of certain natural fibers in the reduction of pollutants in leachate
have been obtained results of COD removals between 67.9% and
90.9%, Turbidity between 88.0% and 99.7% and Color between
67.4% and 90.4%.The expectation generated is to continue evaluating
the association of efficiency of other natural fibers with other landfill
leachate treatment processes.
Abstract: This work studies the effect of chemical composition
on the activity and selectivity of γ–alumina supported CuO/
MnO2/Cr2O3 catalysts toward deep oxidation of CO, dimethyl ether
(DME) and methanol. The catalysts were prepared by impregnation
of the support with an aqueous solution of copper nitrate, manganese
nitrate and CrO3 under different conditions. Thermal, XRD and TPR
analysis were performed. The catalytic measurements of single
compounds oxidation were carried out on continuous flow equipment
with a four-channel isothermal stainless steel reactor. Flow-line
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions that mimic closely the industrial
ones was used. The reactant and product gases were analyzed by
means of on-line gas chromatographs.
On the basis of XRD analysis it can be concluded that the active
component of the mixed Cu-Mn-Cr/γ–alumina catalysts consists of at
least six compounds – CuO, Cr2O3, MnO2, Cu1.5Mn1.5O4,
Cu1.5Cr1.5O4 and CuCr2O4, depending on the Cu/Mn/Cr molar ratio.
Chemical composition strongly influences catalytic properties, this
influence being quite variable with regards to the different processes.
The rate of CO oxidation rapidly decrease with increasing of
chromium content in the active component while for the DME was
observed the reverse trend. It was concluded that the best
compromise are the catalysts with Cu/(Mn + Cr) molar ratio 1:5 and
Mn/Cr molar ratio from 1:3 to 1:4.
Abstract: Currently, continuous two-phase decanter process
used for olive oil production is the more internationally widespread.
The wastewaters generated from this industry (OMW) are a real
environmental problem because of its high organic load. Among
proposed treatments for these wastewaters, advanced oxidation
technologies (Fenton, ozone, photoFenton, etc.) are the most
favourable. The direct application of these processes is somewhat
expensive. Therefore, the application of a previous stage based on a
flocculation-sedimentation operation is of high importance. In this
research five commercial flocculants (three cationic, and two anionic)
have been used to achieve the separation of phases (liquid clarifiedsludge).
For each flocculant, different concentrations (0-1000 mg/L)
have been studied. In these experiments, sludge volume formed and
the final water quality were determined. The final removal
percentages of total phenols (11.3-25.1%), COD (5.6-20.4%), total
carbon (2.3-26.5%), total organic carbon (1.50-23.8%), total nitrogen
(1.45-24.8%), and turbidity (27.9-61.4%) were determined. The
variation on electric conductivity reduction percentage (1-8%) was
also determined. Finally, the best flocculants with highest removal
percentages have been determined (QG2001 and Flocudex CS49).
Abstract: We present a gas-liquid microfluidic system as a
reactor to obtain magnetite nanoparticles with an excellent degree of
control regarding their crystalline phase, shape and size. Several
types of microflow approaches were selected to prevent nanomaterial
aggregation and to promote homogenous size distribution. The
selected reactor consists of a mixer stage aided by ultrasound waves
and a reaction stage using a N2-liquid segmented flow to prevent
magnetite oxidation to non-magnetic phases. A milli-fluidic reactor
was developed to increase the production rate where a magnetite
throughput close to 450 mg/h in a continuous fashion was obtained.
Abstract: Microbes have been used to solve environmental
problems for many years. The role of microorganism to sequester,
precipitate or alter the oxidation state of various heavy metals has
been extensively studied. Treatment using microorganism interacts
with toxic metal are very diverse. The purpose of this research is to
remove the mercury using Pseudomonas putida (P. putida), pure
culture ATTC 49128 at optimum growth parameters such as
techniques of culture, acclimatization time and speed of incubator
shaker. Thus, in this study, the optimum growth parameters of P.
putida were obtained to achieve the maximum of mercury removal.
Based on the optimum parameters of P. putida for specific growth
rate, the removal of two different mercury concentration, 1 ppm and
4 ppm were studied. From mercury nitrate solution, a mercuryresistant
bacterial strain which is able to reduce from ionic mercury
to metallic mercury was used to reduce ionic mercury. The overall
levels of mercury removal in this study were between 80% and 89%.
The information obtained in this study is of fundamental for
understanding of the survival of P. putida ATTC 49128 in mercury
solution. Thus, microbial mercury removal is a potential
bioremediation for wastewater especially in petrochemical industries
in Malaysia.
Abstract: The effect of additional magnesium oxide (MgO) was
investigated by using the tungsten oxide supported on silica catalyst
(WOx/SiO2) physically mixed with MgO in a weight ratio 1:1. The
both fresh and spent catalysts were characterized by FT-Raman
spectrometer, UV-Vis spectrometer, X-Ray diffraction (XRD) and
temperature programmed oxidation (TPO). The results indicated that
the additional MgO could enhance the conversion of trans-2-butene
due to isomerization reaction. However, adding MgO would increase
the amount of coke deposit on the WOx/SiO2 catalyst. The TPO
profile presented two peaks when the WOx/SiO2 catalyst was
physically mixed with MgO. The further peak was suggested that
came from coke precursor could be produced by isomerization
reaction of undesired product. Then, the occurred coke precursor
could deposit and form coke on the acid catalyst.
Abstract: Pt/γ-Al2O3 membrane catalysts were prepared via an
evaporative-crystallization deposition method. The obtained Pt/γ-
Al2O3 catalyst activity was tested after characterization (SEM-EDAX
observation, BET measurement, permeability assessment) in the
catalytic oxidation of selected volatile organic compound (VOC) i.e.
propane, fed in mixture of oxygen. The VOC conversion (nearly
90%) obtained by varying the operating temperature showed that
flow-through membrane reactor might do better in the abatement of
VOCs.
Abstract: The potential neuroprotective effect of Phyllantus
nuriri against Fe2+ and sodium nitroprusside (SNP) induced oxidative
stress in mitochondria of rats brain was evaluated. Cellular viability
was assessed by MTT reduction, reactive oxygen species (ROS)
generation was measured using the probe 2,7-dichlorofluoresce
indiacetate (DCFH-DA). Glutathione content was measured using
dithionitrobenzoic acid (DTNB). Fe2+ (10μM) and SNP (5μM)
significantly decreased mitochondrial activity, assessed by MTT
reduction assay, in a dose-dependent manner, this occurred in parallel
with increased glutathione oxidation, ROS production and lipid
peroxidation end-products (thiobarbituric acid reactive substances,
TBARS). The co-incubation with methanolic extract of Phyllantus
nuriri (10-200 μg/ml) reduced the disruption of mitochondrial
activity, gluthathione oxidation, ROS production as well as the
increase in TBARS levels caused by both Fe2+ and SNP in a dose
dependent manner. HPLC analysis of the extract revealed the
presence of gallic acid (20.540.01), caffeic acid (7.930.02), rutin
(25.310.05), quercetin (31.280.03) and kaemferol (14.360.01).
This result suggests that these phytochemicals account for the
protective actions of P. niruri against Fe2+ and SNP -induced
oxidative stress. Our results show that P. nuriri consist important
bioactive molecules in the search for an improved therapy against the
deleterious effects of Fe2+, an intrinsic producer of reactive oxygen
species (ROS), that leads to neuronal oxidative stress and
neurodegeneration.
Abstract: This paper presents the design and fabrication of an
optical window for an optical modulator toward image sensing
applications. An optical window consists of micrometer-order SiO2
capillaries (porous solid) that can modulate transmission light
intensity by moving the liquid in and out of porous solid. A high
optical transmittance of the optical window can be achieved due to
refractive index matching when the liquid is penetrated into the
porous solid. Otherwise, its light transmittance is lower because of
light reflection and scattering by air holes and capillary walls. Silicon
capillaries fabricated by deep reactive ion etching (DRIE) process are
completely oxidized to form the SiO2 capillaries. Therefore, high
aspect ratio SiO2 capillaries can be achieved based on silicon
capillaries formed by DRIE technique. Large compressive stress of
the oxide causes bending of the capillary structure, which is reduced
by optimizing the design of device structure. The large stress of the
optical window can be released via thin supporting beams. A 7.2 mm
x 9.6 mm optical window area toward a fully integrated with the
image sensor format is successfully fabricated and its optical
transmittance is evaluated with and without inserting liquids (ethanol
and matching oil). The achieved modulation range is approximately
20% to 35% with and without liquid penetration in visible region
(wavelength range from 450 nm to 650 nm).
Abstract: This article presents modeling studies of NiAl alloy
under solid-particle erosion and liquid-drop erosion. In the
solid-particle erosion simulation, attention is paid to the oxide scale
thickness variation on the alloy in high-temperature erosion
environments. The erosion damage is assumed to be deformation wear
and cutting wear mechanisms, incorporating the influence of the oxide
scale on the eroded surface; thus the instantaneous oxide thickness is
the result of synergetic effect of erosion and oxidation. For liquid-drop
erosion, special interest is in investigating the effects of drop velocity
and drop size on the damage of the target surface. The models of
impact stress wave, mean depth of penetration, and maximum depth of
erosion rate (Max DER) are employed to develop various maps for
NiAl alloy, including target thickness vs. drop size (diameter), rate of
mean depth of penetration (MDRP) vs. drop impact velocity, and
damage threshold velocity (DTV) vs. drop size.
Abstract: Machining of hard materials is a recent technology for
direct production of work-pieces. The primary challenge in
machining these materials is selection of cutting tool inserts which
facilitates an extended tool life and high-precision machining of the
component. These materials are widely for making precision parts for
the aerospace industry. Nickel-based alloys are typically used in
extreme environment applications where a combination of strength,
corrosion resistance and oxidation resistance material characteristics
are required. The present paper reports the theoretical and
experimental investigations carried out to understand the influence of
machining parameters on the response parameters. Considering the
basic machining parameters (speed, feed and depth of cut) a study has
been conducted to observe their influence on material removal rate,
surface roughness, cutting forces and corresponding tool wear.
Experiments are designed and conducted with the help of Central
Composite Rotatable Design technique. The results reveals that for a
given range of process parameters, material removal rate is favorable
for higher depths of cut and low feed rate for cutting forces. Low feed
rates and high values of rotational speeds are suitable for better finish
and higher tool life.
Abstract: The development of active and stable catalysts
without noble metals for low temperature oxidation of exhaust gases
remains a significant challenge. The purpose of this study is to
determine the influence of the preparation method on the catalytic
activity of the supported copper-manganese mixed oxides in terms of
VOCs oxidation. The catalysts were prepared by impregnation of γ-
Al2O3 with copper and manganese nitrates and acetates and the
possibilities for CO, CH3OH and dimethyl ether (DME) oxidation
were evaluated using continuous flow equipment with a four-channel
isothermal stainless steel reactor. Effect of the support, Cu/Mn mole
ratio, heat treatment of the precursor and active component loading
were investigated. Highly active alumina supported Cu-Mn catalysts
for CO and VOCs oxidation were synthesized. The effect of
preparation conditions on the activity behavior of the catalysts was
discussed.
The synergetic interaction between copper and manganese species
increases the activity for complete oxidation over mixed catalysts.
Type of support, calcination temperature and active component
loading along with catalyst composition are important factors,
determining catalytic activity. Cu/Mn molar ratio of 1:5, heat
treatment at 450oC and 20 % active component loading are the best
compromise for production of active catalyst for simultaneous
combustion of CO, CH3OH and DME.
Abstract: Iron is an essential nutrient with limited
bioavailability. Nutritional anemia caused mainly by iron deficiency
is the most recognized nutritional problem in both countries as well
as affluent societies. Rice (Oryza sativa L.) has become the most
important cereal crop for the improvement of human health due to the
starch, protein, oil, and the majority of micronutrients, particularly in
Asian countries. In this study, the iron availability and profile lipid
were evaluated for the extracts from Cibeusi varieties (black rices) of
ancient rice brans.
Results: The quality of K, B, R, E diets groups shows the same
effect on the growth of rats. Hematocrit and MCHC levels of rats fed
K, B, R and E diets were not significantly (P
Abstract: For centuries humans have used the antimicrobial
properties of copper to their advantage. Yet, after all these years the
underlying mechanisms of copper mediated cell death in various
microbes remain unclear. We had explored the hypothesis that copper
mediated increased levels of lipid peroxidation in the membrane fatty
acids is responsible for increased killing in Escherichia coli. In this
study we show that in both gram positive (Staphylococcus aureus)
and gram negative (Pseudomonas aeruginosa) bacteria there is a
strong correlation between copper mediated cell death and increased
levels of lipid peroxidation. Interestingly, the non-spore forming
gram positive bacteria as well as gram negative bacteria show similar
patterns of cell death, increased levels of lipid peroxidation, as well
as genomic DNA degradation, however there is some difference in
loss in membrane integrity upon exposure to copper alloy surface.
Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: The study examined the effect of Bonny Light whole
crude oil (WC) and its water soluble fraction (WSF) on the activities
of antioxidant enzymes (catalase (CAT) and superoxide dismutase
(SOD)) and crude mitochondria ATPases in the radicle of
germinating bean (Vigna unguiculata). The percentage germination,
level of lipid peroxidation, antioxidant enzyme and mitochondria
Ca2+ and Mg2+ ATPase activities were measured in the radicle of
bean after 7, 14 and 21 days post germination. Viable bean seeds
were planted in soils contaminated with 10ml, 25ml and 50ml of
whole crude oil (WC) and its water soluble fraction (WSF) to obtain
2, 5 and 10% v/w crude oil contamination. There was dose dependent
reduction of the number of bean seeds that germinated in the
contaminated soils compared with control (p