Abstract: As per the statistical data, the Doubly-fed Induction
Generator (DFIG) based wind turbine with variable speed and
variable pitch control is the most common wind turbine in the
growing wind market. This machine is usually used on the grid
connected wind energy conversion system to satisfy grid code
requirements such as grid stability, Fault Ride Through (FRT), power
quality improvement, grid synchronization and power control etc.
Though the requirements are not fulfilled directly by the machine, the
control strategy is used in both the stator as well as rotor side along
with power electronic converters to fulfil the requirements stated
above. To satisfy the grid code requirements of wind turbine, usually
grid side converter is playing a major role. So in order to improve the
operation capacity of wind turbine under critical situation, the
intensive study of both machine side converter control and grid side
converter control is necessary In this paper DFIG is modeled using
power components as variables and the performance of the DFIG
system is analysed under grid voltage fluctuations. The voltage
fluctuations are made by lowering and raising the voltage values in
the utility grid intentionally for the purpose of simulation keeping in
view of different grid disturbances.
Abstract: This paper presents a power control for a Doubly Fed
Induction Generator (DFIG) using in Wind Energy Conversion
System (WECS) connected to the grid. The proposed control strategy
employs two nonlinear controllers, Backstipping (BSC) and slidingmode
controller (SMC) scheme to directly calculate the required
rotor control voltage so as to eliminate the instantaneous errors of
active and reactive powers. In this paper the advantages of BSC and
SMC are presented, the performance and robustness of this two
controller’s strategy are compared between them. First, we present a
model of wind turbine and DFIG machine, then a synthesis of the
controllers and their application in the DFIG power control.
Simulation results on a 1.5MW grid-connected DFIG system are
provided by MATLAB/Simulink.
Abstract: Biodiesel is one of the alternative fuels that promising
for substituting petro diesel as energy source which is advantage on
sustainability and ecofriendly. Due to the raw material that tend to
decompose during storage, biodiesel also have the same characteristic
that tend to decompose and formed higher acid value which is the
result of oxidation to double bond on a chain of ester. Decomposition of biodiesel due to oxidation reaction could
prevent by introduce a small amount of antioxidant. The origin of raw
materials and the process for producing biodiesel will determine the
effectiveness of antioxidant. The quality degradation on biodiesel
could evaluate by measuring iodine value and acid number of
biodiesel. Biodiesel made from high fatty acid Jatropha curcas oil by using
esterification and transesterification process will stand on the quality
by introduce 90 ppm pyrogallol powder on the biodiesel, which could
increase Induction period time from 2 hours to more than 6 hours in
rancimat test evaluation.
Abstract: The work aims to develop a robot in the form of
autonomous vehicle to detect, inspection and mapping of
underground pipelines through the ATmega328 Arduino platform.
Hardware prototyping is very similar to C / C ++ language that
facilitates its use in robotics open source, resembles PLC used in
large industrial processes. The robot will traverse the surface
independently of direct human action, in order to automate the
process of detecting buried pipes, guided by electromagnetic
induction. The induction comes from coils that send the signal to the
Arduino microcontroller contained in that will make the difference in
intensity and the treatment of the information, and then this
determines actions to electrical components such as relays and
motors, allowing the prototype to move on the surface and getting the
necessary information. This change of direction is performed by a
stepper motor with a servo motor. The robot was developed by
electrical and electronic assemblies that allowed test your application.
The assembly is made up of metal detector coils, circuit boards and
microprocessor, which interconnected circuits previously developed
can determine, process control and mechanical actions for a robot
(autonomous car) that will make the detection and mapping of buried
pipelines plates. This type of prototype can prevent and identifies
possible landslides and they can prevent the buried pipelines suffer an
external pressure on the walls with the possibility of oil leakage and
thus pollute the environment.
Abstract: In this paper, the cable model of dendrites have been
considered. The dendrites are cylindrical cables of various segments
having variable length and reducing radius from start point at synapse
and end points. For a particular event signal being received by a
neuron in response only some dendrite are active at a particular
instance. Initial current signals with different current flows in
dendrite are assumed. Due to overlapping and coupling of active
dendrite, they induce currents in the dendrite segments of each other
at a particular instance. But how these currents are induced in the
various segments of active dendrites due to coupling between these
dendrites, It is not presented in the literature. Here the paper presents
a model for induced currents in active dendrite segments due to
mutual coupling at the starting instance of an activity in dendrite. The
model is as discussed further.
Abstract: Background: Delayed onset muscle soreness (DOMS)
is the most common symptom when ordinary individuals and athletes
are exposed to unaccustomed physical activity, especially eccentric
contraction which impairs athletic performance, ordinary people
work ability and physical functioning. Multitudes of methods have
been investigated to reduce DOMS. One of the valuable methods to
control DOMS is repeated bout effect (RBE) as a prophylactic
method. Purpose: To compare the repeated bout effect of
submaximal eccentric with maximal isometric contraction on induced
DOMS. Methods: Sixty normal male volunteers were assigned
randomly into three equal groups: Group A (first study group): 20
subjects received submaximal eccentric contraction on non-dominant
elbow flexors as a prophylactic exercise. Group B (second study
group): 20 subjects received maximal isometric contraction on nondominant
elbow flexors as a prophylactic exercise. Group C (control
group): 20 subjects did not receive any prophylactic exercises.
Maximal isometric peak torque of elbow flexors and patient related
elbow evaluation (PREE) scale were measured for each subject 3
times before, immediately after, and 48 hours after induction of
DOMS. Results: Post-hoc test for maximal isometric peak torque and
PREE scale immediately and 48 hours after induction of DOMS
revealed that group (A) and group (B) resulted in significant decrease
in maximal isometric strength loss and elbow pain and disability
rather than control group (C), but submaximal eccentric group (A)
was more effective than maximal isometric group (B) as it showed
more rapid recovery of functional strength and less degrees of elbow
pain and disability. Conclusion: Both submaximal eccentric
contraction and maximal isometric contraction were effective in
prevention of DOMS but submaximal eccentric contraction produced
a greater protective effect against muscle damage induced by
maximal eccentric exercise performed 2 days later.
Abstract: STRIM (Statistical Test Rule Induction Method) has been proposed as a method to effectively induct if-then rules from the decision table which is considered as a sample set obtained from the population of interest. Its usefulness has been confirmed by simulation experiments specifying rules in advance, and by comparison with conventional methods. However, scope for future development remains before STRIM can be applied to the analysis of real-world data sets. The first requirement is to determine the size of the dataset needed for inducting true rules, since finding statistically significant rules is the core of the method. The second is to examine the capacity of rule induction from datasets with contaminated attribute values created by missing data and noise, since real-world datasets usually contain such contaminated data. This paper examines the first problem theoretically, in connection with the rule length. The second problem is then examined in a simulation experiment, utilizing the critical size of dataset derived from the first step. The experimental results show that STRIM is highly robust in the analysis of datasets with contaminated attribute values, and hence is applicable to real-world data
Abstract: By the evolvement in technology, the way of
expressing opinions switched direction to the digital world. The
domain of politics, as one of the hottest topics of opinion mining
research, merged together with the behavior analysis for affiliation
determination in texts, which constitutes the subject of this paper.
This study aims to classify the text in news/blogs either as
Republican or Democrat with the minimum number of features. As
an initial set, 68 features which 64 were constituted by Linguistic
Inquiry and Word Count (LIWC) features were tested against 14
benchmark classification algorithms. In the later experiments, the
dimensions of the feature vector reduced based on the 7 feature
selection algorithms. The results show that the “Decision Tree”,
“Rule Induction” and “M5 Rule” classifiers when used with “SVM”
and “IGR” feature selection algorithms performed the best up to
82.5% accuracy on a given dataset. Further tests on a single feature
and the linguistic based feature sets showed the similar results. The
feature “Function”, as an aggregate feature of the linguistic category,
was found as the most differentiating feature among the 68 features
with the accuracy of 81% in classifying articles either as Republican
or Democrat.
Abstract: Nowadays, the use of renewable energy sources has been increasingly great because of the cost increase and public demand for clean energy sources. One of the fastest growing sources is wind energy. In this paper, Wind Diesel Hybrid System (WDHS) comprising a Diesel Generator (DG), a Wind Turbine Generator (WTG), the Consumer Load, a Battery-based Energy Storage System (BESS), and a Dump Load (DL) is used. Voltage is controlled by Diesel Generator; the frequency is controlled by BESS and DL. The BESS elimination is an efficient way to reduce maintenance cost and increase the dynamic response. Simulation results with graphs for the frequency of Power System, active power, and the battery power are presented for load changes. The controlling parameters are optimized by using Imperialist Competitive Algorithm (ICA). The simulation results for the BESS/no BESS cases are compared. Results show that in no BESS case, the frequency control is more optimal than the BESS case by using ICA.
Abstract: This paper presents a numerical investigation of two
horizontally mounted four-lobed swirl pipes in terms of swirl
induction effectiveness into flows passing through them. The swirl
flows induced by the two swirl pipes have the potential to improve
the efficiency of Clean-In-Place procedures in a closed processing
system by local intensification of hydrodynamic impact on the
internal pipe surface. Pressure losses, swirl development within the
two swirl pipe, swirl induction effectiveness, swirl decay and wall
shear stress variation downstream of two swirl pipes are analyzed and
compared. It was found that a shorter length of swirl inducing pipe
used in joint with transition pipes is more effective in swirl induction
than when a longer one is used, in that it has a less constraint to the
induced swirl and results in slightly higher swirl intensity just
downstream of it with the expense of a smaller pressure loss. The
wall shear stress downstream of the shorter swirl pipe is also slightly
larger than that downstream of the longer swirl pipe due to the
slightly higher swirl intensity induced by the shorter swirl pipe. The
advantage of the shorter swirl pipe in terms of swirl induction is more
significant in flows with a larger Reynolds Number.
Abstract: DC motors have been widely used in the past
centuries which are proudly known as the workhorse of industrial
systems until the invention of the AC induction motors which makes
a huge revolution in industries. Since then, the use of DC machines
has been decreased due to enormous factors such as reliability,
robustness and complexity but it lost its fame due to the losses. In this
paper a new methodology is proposed to construct a DC motor
through the simulation in LabVIEW to get an idea about its real time
performances, if a change in parameter might have bigger
improvement in losses and reliability.
Abstract: Proposed paper dealt with the modelling and analysis of induction motor based on the mathematical expression using the graphical programming environment of Laboratory Virtual Instrument Engineering Workbench (LabVIEW). Induction motor modelling with the mathematical expression enables the motor to be simulated with the various required parameters. Owing to the invention of variable speed drives study about the induction motor characteristics became complex. In this simulation motor internal parameter such as stator resistance and reactance, rotor resistance and reactance, phase voltage, frequency and losses will be given as input. By varying the speed of motor corresponding parameters can be obtained they are input power, output power, efficiency, torque induced, slip and current.
Abstract: If teamwork is the key to organizational learning,
productivity and growth, then, why do some teams succeed in
achieving these, while others falter at different stages? Building
teams in higher education institutions has been a challenge and an
open-ended constructivist approach was considered on an
experimental basis for this study to address this challenge. For this
research, teams of students from the MBA program were chosen to
study the effect of teamwork in learning, the motivation levels among
student team members, and the effect of collaboration in achieving
team goals. The teams were built on shared vision and goals,
cohesion was ensured, positive induction in the form of faculty
mentoring was provided for each participating team and the results
have been presented with conclusions and suggestions.
Abstract: This paper outlines the basic installation and operation of magnetic inductive flow velocity sensors on large underground cooling water pipelines. Research on the effects of cathodic protection as well as into other factors that might influence the overall performance of the meter is presented in this paper. The experiments were carried out on an immersion type magnetic meter specially used for flow measurement of cooling water pipeline. An attempt has been made in this paper to outline guidelines that can ensure accurate measurement related to immersion type magnetic meters on underground pipelines.
Abstract: The paper presents a practical three-phase PWM
inverter suitable for low voltage, low rating energy efficient systems.
The work in the paper is conducted with the view to establishing the
significance of the loss contribution from the PWM inverter in the
determination of the complete losses of a photovoltaic (PV) arraypowered
induction motor drive water pumping system. Losses
investigated include; conduction and switching loss of the devices
and gate drive losses. It is found that the PWM inverter operates at a
reasonable variable efficiency that does not fall below 92%
depending on the load. The results between the simulated and
experimental results for the system with or without a maximum
power tracker (MPT) compares very well, within an acceptable range
of 2% margin.
Abstract: In this research (using induction furnace process)
nodular iron with three different percentages of copper (residual,
0.5% and 1,2%) was obtained. Chemical analysis was performed by
mass spectrometry and microstructures were characterized by Optical
Microscopy (ASTM E3) and Scanning Electron Microscopy (SEM).
The study of mechanical behavior was carried out in a mechanical
test machine (ASTM E8) and a Pin on disk tribometer (ASTM G99)
was used to assess wear resistance. It is observed that the dissolution
of copper in crystal lattice increases the pearlite structure improving
the wear and hardness behavior, but producing a contrary effect on
the energy absorption.
Abstract: ESPRIT-TLS method appears a good choice for high
resolution fault detection in induction machines. It has a very high
effectiveness in the frequency and amplitude identification.
Contrariwise, it presents a high computation complexity which
affects its implementation in real time fault diagnosis. To avoid this
problem, a Fast-ESPRIT algorithm that combined the IIR band-pass
filtering technique, the decimation technique and the original
ESPRIT-TLS method was employed to enhance extracting accurately
frequencies and their magnitudes from the wind stator current with
less computation cost. The proposed algorithm has been applied to
verify the wind turbine machine need in the implementation of an online,
fast, and proactive condition monitoring. This type of remote
and periodic maintenance provides an acceptable machine lifetime,
minimize its downtimes and maximize its productivity. The
developed technique has evaluated by computer simulations under
many fault scenarios. Study results prove the performance of Fast-
ESPRIT offering rapid and high resolution harmonics recognizing
with minimum computation time and less memory cost.
Abstract: Based on the experimental data, the impact of
resistance and reactance of the winding, as well as the magnetic
permeability of the magnetic circuit steel material on the value of the
electromotive force of the induction converter is investigated. The
obtained results allow estimating the main technological spreads and
determining the maximum level of the electromotive force change.
By the method of experiment planning, the expression of a
polynomial for the electromotive force which can be used to estimate
the adequacy of mathematical models to be used at the investigation
and design of induction converters is obtained.
Abstract: Ocimum americanum L (Lamiaceae) is an annual herb
that is native to tropical Africa. The in vitro and in vivo antioxidant
activity of its aqueous extract was carefully investigated by assessing
the DPPH radical scavenging activity, ABTS radical scavenging
activity and hydrogen peroxide radical scavenging activity. The
reducing power, total phenol, total flavonoids and flavonols content
of the extract were also evaluated. The data obtained revealed that the
extract is rich in polyphenolic compounds and scavenged the radicals
in a concentration dependent manner. This was done in comparison
with the standard antioxidants such as BHT and Vitamin C. Also, the
induction of oxidative damage with paracetamol (2000 mg/kg)
resulted in the elevation of lipid peroxides and significant (P < 0.05)
decrease in activities of superoxide dismutase, glutathione
peroxidase, glutathione reductase and catalase in the liver and kidney
of rats. However, the pretreatment of rats with aqueous extract of O.
americanum leaves (200 and 400 mg/kg) and silymarin (100 mg/kg)
caused a significant (P < 0.05) reduction in the values of lipid
peroxides and restored the levels of antioxidant parameters in these
organs. These findings suggest that the leaves of O. americanum have
potent antioxidant properties which may be responsible for its
acclaimed folkloric uses.
Abstract: The current study investigated the influence of milling
time and ball-to-powder (BPR) weight ratio on the microstructural
constituents and mechanical properties of bulk nanocrystalline Al;
Al-10%Cu; and Al-10%Cu-5%Ti alloys. Powder consolidation was
carried out using a high frequency induction heat sintering where the
processed metal powders were sintered into a dense and strong bulk
material. The powders and the bulk samples were characterized using
XRD and FEGSEM techniques. The mechanical properties were
evaluated at various temperatures of 25°C, 100°C, 200°C, 300°C and
400°C to study the thermal stability of the processed alloys. The
processed bulk nanocrystalline alloys displayed extremely high
hardness values even at elevated temperatures. The Al-10%Cu-5%Ti
alloy displayed the highest hardness values at room and elevated
temperatures which are related to the presence of Ti-containing
phases such as Al3Ti and AlCu2Ti. These phases are thermally stable
and retain the high hardness values at elevated temperatures up to
400ºC.