Abstract: This research was conducted in the Lower Namkam
Irrigation Project situated in the Namkam River Basin in Thailand.
Degradation of groundwater quality in some areas is caused by saline
soil spots beneath ground surface. However, the tail regulated gate
structure on the Namkam River, a lateral stream of the Mekong
River. It is aimed for maintaining water level in the river at +137.5 to
+138.5 m (MSL) and flow to the irrigation canals based on a gravity
system since July 2009. It might leach some saline soil spots from
underground to soil surface if lack of understanding of the
conjunctive surface water and groundwater behaviors. This research
has been conducted by continuously the observing of both shallow
and deep groundwater level and quality from existing observation
wells. The simulation of surface water was carried out using a
hydrologic modeling system (HEC-HMS) to compute the ungauged
side flow catchments as the lateral flows for the river system model
(HEC-RAS). The constant water levels in the upstream of the
operated gate caused a slight rising up of shallow groundwater level
when compared to the water table. However, the groundwater levels
in the confined aquifers remained less impacted than in the shallow
aquifers but groundwater levels in late of wet season in some wells
were higher than the phreatic surface. This causes salinization of the
groundwater at the soil surface and might affect some crops. This
research aims for the balance of water stage in the river and efficient
groundwater utilization in this area.
Abstract: Sampling and analysis of leachate from Bhalaswa
landfill and groundwater samples from nearby locations, clearly
indicated the likely contamination of groundwater due to landfill
leachate. The results of simulation studies carried out for the
migration of Chloride from landfill shows that the simulation results
are in consonance with the observed concentration of Chloride in the
vicinity of landfill facility. The solid waste disposal system presently
being practiced in Delhi consists of mere dumping of wastes
generated, at three locations Bhalaswa, Ghazipur, and Okhla without
any regard to proper care for the protection of surrounding
environment. Bhalaswa landfill site in Delhi, which is being operated
as a dump site, is expected to become cause of serious groundwater
pollution in its vicinity. The leachate from Bhalaswa landfill was
found to be having a high concentration of chlorides, as well as DOC,
COD. The present study was undertaken to determine the likely
concentrations of principle contaminants in the groundwater over a
period of time due to the discharge of such contaminants from
landfill leachates to the underlying groundwater. The observed
concentration of chlorides in the groundwater within 75m of the
radius of landfill facility was found to be in consonance with the
simulated concentration of chloride in groundwater considering one
dimensional transport model, with finite mass of contaminant source.
Governing equation of contaminant transport involving advection and
diffusion-dispersion was solved in matlab7.0 using finite difference
method.
Abstract: South Africa is facing a crisis with not being able to produce enough graduates in the scarce skills areas to sustain economic growth. The crisis is fuelled by a school system that does not produce enough potential students with Mathematics, Accounting and Science. Since the introduction of the new school curriculum in 2008, there is no longer an option to take pure maths on a standard grade level. Instead, only two mathematical subjects are offered: pure maths (which is on par with higher grade maths) and mathematical literacy. It is compulsory to take one or the other. As a result, lees student finishes Grade 12 with pure mathematics every year. This national problem needs urgent attention if South Africa is to make any headway in critical skills development as mathematics is a gateway to scarce skills professions. Higher education institutions initiated several initiatives in an attempt to address the above, including preparatory courses, bridging programmes and extended curricula with foundation provisions. In view of the above, and government policy directives to broaden access in the scarce skills areas to increase student throughput, foundation provision was introduced for Commerce and Information Technology programmes at the Vaal Triangle Campus (VTC) of North-West University (NWU) in 2010. Students enrolling for extended programmes do not comply with the minimum prerequisites for the normal programmes. The question then arises as to whether these programmes have the intended impact? This paper reports the results of a two year longitudinal study, tracking the first year academic achievement of the two cohorts of enrolments since 2010. The results provide valuable insight into the structuring of an extended programme and its potential impact.
Abstract: A Ground Control System (GCS), which controls Unmanned Aerial Vehicles (UAVs) and monitors their missionrelated data, is one of the major components of UAVs. In fact, some traditional GCSs were built on an expensive, complicated hardware infrastructure with workstations and PCs. In contrast, a GCS on a portable device – such as an Android phone or tablet – takes advantage of its light-weight hardware and the rich User Interface supported by the Android Operating System. We implemented that kind of GCS and called it Ground System Software (GSS) in this paper. In operation, our GSS communicates with UAVs or other GSS via TCP/IP connection to get mission-related data, visualizes it on the device-s screen, and saves the data in its own database. Our study showed that this kind of system will become a potential instrument in UAV-related systems and this kind of topic will appear in many research studies in the near future.
Abstract: In this paper a novel algorithm is proposed that integrates the process of fuzzy hierarchy generation and rule discovery for automated discovery of Production Rules with Fuzzy Hierarchy (PRFH) in large databases.A concept of frequency matrix (Freq) introduced to summarize large database that helps in minimizing the number of database accesses, identification and removal of irrelevant attribute values and weak classes during the fuzzy hierarchy generation.Experimental results have established the effectiveness of the proposed algorithm.
Abstract: WLAN Positioning has been presented by many
approaches in literatures using the characteristics of Received Signal
Strength (RSS), Time of Arrival (TOA) or Time Difference of
Arrival (TDOA), Angle of Arrival (AOA) and cell ID. Among these,
RSS approach is the simplest method to implement because there is
no need of modification on both access points and client devices
whereas its accuracy is terrible due to physical environments. For
TOA or TDOA approach, the accuracy is quite acceptable but most
researches have to modify either software or hardware on existing
WLAN infrastructure. The scales of modifications are made on only
access card up to the changes in protocol of WLAN. Hence, it is an
unattractive approach to use TOA or TDOA for positioning system.
In this paper, the new concept of merging both RSS and TOA
positioning techniques is proposed. In addition, the method to
achieve TOA characteristic for positioning WLAN user without any
extra modification necessarily appended in the existing system is
presented. The measurement results confirm that the proposed
technique using both RSS and TOA characteristics provides better
accuracy than using only either RSS or TOA approach.
Abstract: Fully customized hardware based technology provides high performance and low power consumption by specializing the tasks in hardware but lacks design flexibility since any kind of changes require re-design and re-fabrication. Software based solutions operate with software instructions due to which a great flexibility is achieved from the easy development and maintenance of the software code. But this execution of instructions introduces a high overhead in performance and area consumption. In past few decades the reconfigurable computing domain has been introduced which overcomes the traditional trades-off between flexibility and performance and is able to achieve high performance while maintaining a good flexibility. The dramatic gains in terms of chip performance and design flexibility achieved through the reconfigurable computing systems are greatly dependent on the design of their computational units being integrated with reconfigurable logic resources. The computational unit of any reconfigurable system plays vital role in defining its strength. In this research paper an RFU based computational unit design has been presented using the tightly coupled, multi-threaded reconfigurable cores. The proposed design has been simulated for VLIW based architectures and a high gain in performance has been observed as compared to the conventional computing systems.
Abstract: Image data holds a large amount of different context
information. However, as of today, these resources remain largely
untouched. It is thus the aim of this paper to present a basic technical
framework which allows for a quick and easy exploitation of context
information from image data especially by non-expert users.
Furthermore, the proposed framework is discussed in detail
concerning important social and ethical issues which demand special
requirements in system design. Finally, a first sensor prototype is
presented which meets the identified requirements. Additionally,
necessary implications for the software and hardware design of the
system are discussed, rendering a sensor system which could be
regarded as a good, acceptable and justifiable technical and thereby
enabling the extraction of context information from image data.
Abstract: This paper presents a design and prototype
implementation of new home automation system that uses WiFi
technology as a network infrastructure connecting its parts. The
proposed system consists of two main components; the first part is
the server (web server), which presents system core that manages,
controls, and monitors users- home. Users and system administrator
can locally (LAN) or remotely (internet) manage and control system
code. Second part is hardware interface module, which provides
appropriate interface to sensors and actuator of home automation
system. Unlike most of available home automation system in the
market the proposed system is scalable that one server can manage
many hardware interface modules as long as it exists on WiFi
network coverage. System supports a wide range of home
automation devices like power management components, and
security components. The proposed system is better from the
scalability and flexibility point of view than the commercially
available home automation systems.
Abstract: The advent of multi-million gate Field Programmable
Gate Arrays (FPGAs) with hardware support for multiplication opens
an opportunity to recreate a significant portion of the front end of a
human cochlea using this technology. In this paper we describe the
implementation of the cochlear filter and show that it is entirely
suited to a single device XC3S500 FPGA implementation .The filter
gave a good fit to real time data with efficiency of hardware usage.
Abstract: Risk of infectious disease outbreaks is related to the
hygiene among the population. To assess the actual risks and modify
the relevant emergency procedures if necessary, a hygiene survey
was conducted among undergraduate students on the Rhodes
University campus. Soap was available to 10.5% and only 26.8% of
the study participants followed proper hygiene in relation to food
consumption. This combination increases the risk of infectious
disease outbreaks at the campus. Around 83.6% were willing to wash
their hands if soap was provided. Procurement and availability of
soap in undergraduate residences on campus should be improved, as
the total cost is estimated at only 2000 USD per annum. Awareness
campaigns about food-related hygiene and the need for regular handwashing
with soap should be run among Rhodes University students.
If successful, rates of respiratory and hygiene-related diseases will be
decreased and emergency health management simplified.
Abstract: Finite impulse response (FIR) filters have the advantage of linear phase, guaranteed stability, fewer finite precision errors, and efficient implementation. In contrast, they have a major disadvantage of high order need (more coefficients) than IIR counterpart with comparable performance. The high order demand imposes more hardware requirements, arithmetic operations, area usage, and power consumption when designing and fabricating the filter. Therefore, minimizing or reducing these parameters, is a major goal or target in digital filter design task. This paper presents an algorithm proposed for modifying values and the number of non-zero coefficients used to represent the FIR digital pulse shaping filter response. With this algorithm, the FIR filter frequency and phase response can be represented with a minimum number of non-zero coefficients. Therefore, reducing the arithmetic complexity needed to get the filter output. Consequently, the system characteristic i.e. power consumption, area usage, and processing time are also reduced. The proposed algorithm is more powerful when integrated with multiplierless algorithms such as distributed arithmetic (DA) in designing high order digital FIR filters. Here the DA usage eliminates the need for multipliers when implementing the multiply and accumulate unit (MAC) and the proposed algorithm will reduce the number of adders and addition operations needed through the minimization of the non-zero values coefficients to get the filter output.
Abstract: Decrease in hardware costs and advances in computer
networking technologies have led to increased interest in the use of
large-scale parallel and distributed computing systems. One of the
biggest issues in such systems is the development of effective
techniques/algorithms for the distribution of the processes/load of a
parallel program on multiple hosts to achieve goal(s) such as
minimizing execution time, minimizing communication delays,
maximizing resource utilization and maximizing throughput.
Substantive research using queuing analysis and assuming job
arrivals following a Poisson pattern, have shown that in a multi-host
system the probability of one of the hosts being idle while other host
has multiple jobs queued up can be very high. Such imbalances in
system load suggest that performance can be improved by either
transferring jobs from the currently heavily loaded hosts to the lightly
loaded ones or distributing load evenly/fairly among the hosts .The
algorithms known as load balancing algorithms, helps to achieve the
above said goal(s). These algorithms come into two basic categories -
static and dynamic. Whereas static load balancing algorithms (SLB)
take decisions regarding assignment of tasks to processors based on
the average estimated values of process execution times and
communication delays at compile time, Dynamic load balancing
algorithms (DLB) are adaptive to changing situations and take
decisions at run time.
The objective of this paper work is to identify qualitative
parameters for the comparison of above said algorithms. In future this
work can be extended to develop an experimental environment to
study these Load balancing algorithms based on comparative
parameters quantitatively.
Abstract: In this paper, a simple active contour based visual
tracking algorithm is presented for outdoor AGV application which is
currently under development at the USM robotic research group
(URRG) lab. The presented algorithm is computationally low cost
and able to track road boundaries in an image sequence and can
easily be implemented on available low cost hardware. The proposed
algorithm used an active shape modeling using the B-spline
deformable template and recursive curve fitting method to track the
current orientation of the road.
Abstract: This paper presents an optimization technique to economic load dispatch (ELD) problems with considering the daily load patterns and generator constraints using a particle swarm optimization (PSO). The objective is to minimize the fuel cost. The optimization problem is subject to system constraints consisting of power balance and generation output of each units. The application of a constriction factor into PSO is a useful strategy to ensure convergence of the particle swarm algorithm. The proposed method is able to determine, the output power generation for all of the power generation units, so that the total constraint cost function is minimized. The performance of the developed methodology is demonstrated by case studies in test system of fifteen-generation units. The results show that the proposed algorithm scan give the minimum total cost of generation while satisfying all the constraints and benefiting greatly from saving in power loss reduction
Abstract: The Kowsar dam supply water for different usages
such as drinking, industrial, agricultural and aquaculture farms
usages and located next to the city of Dehdashat in Kohgiluye and
Boyerahmad province in southern Iran. There are some towns and
villages on the Kowsar dam watersheds, which Dehdasht and
Choram are the most important and populated cities in this area. The
study was undertaken to assess the status of water quality in the
urban areas of the Kowsar dam. A total of 28 water samples were
collected from 6 stations on surface water and 1 station from
groundwater on the watershed of the Kowsar dam. All the samples
were analyzed for Cd concentration using standard procedures. The
results were compared with other national and international
standards. Among the analyzed samples, as the maximum value of
cadmium (1.131 μg/L) was observed on the station 2 at the winter
2009, all the samples analyzed were within the maximum admissible
limits by the United States Environmental Protection Agency, EU,
WHO, New Zealand , Australian, Iranian, and the Indian standards.
In general results of the present study have shown that Cd mean
values of stations No. 4, 1 and 2 with 0.5135, 0.0.4733 and 0.4573
μg/L respectively are higher than the other stations . Although Cd
level of all samples and stations have had normal values but this is
an indication of pollution potential and hazards because of human
activity and waste water of towns in the areas, which can effect on
human health implications in future. This research, therefore,
recommends the government and other responsible authorities to take
suitable improving measures in the Kowsar dam watershed-s.
Abstract: Real-time 3D applications have to guarantee
interactive rendering speed. There is a restriction for the number of
polygons which is rendered due to performance of a graphics hardware
or graphics algorithms. Generally, the rendering performance will be
drastically increased when handling only the dynamic 3d models,
which is much fewer than the static ones. Since shapes and colors of
the static objects don-t change when the viewing direction is fixed, the
information can be reused. We render huge amounts of polygon those
cannot handled by conventional rendering techniques in real-time by
using a static object image and merging it with rendering result of the
dynamic objects. The performance must be decreased as a
consequence of updating the static object image including removing
an static object that starts to move, re-rending the other static objects
being overlapped by the moving ones. Based on visibility of the object
beginning to move, we can skip the updating process. As a result, we
enhance rendering performance and reduce differences of rendering
speed between each frame. Proposed method renders total
200,000,000 polygons that consist of 500,000 dynamic polygons and
the rest are static polygons in about 100 frames per second.
Abstract: This paper introduces a hardware solution to password
exposure problem caused by direct accesses to the keyboard hardware
interfaces through which a possible attacker is able to grab user-s
password even where existing countermeasures are deployed. Several
researches have proposed reasonable software based solutions to the
problem for years. However, recently introduced hardware
vulnerability problems have neutralized the software approaches and
yet proposed any effective software solution to the vulnerability.
Hardware approach in this paper is expected as the only solution to the
vulnerability
Abstract: In this paper, a new reverse converter for the moduli set {2n, 2n–1, 2n–1–1} is presented. We improved a previously introduced conversion algorithm for deriving an efficient hardware design for reverse converter. Hardware architecture of the proposed converter is based on carry-save adders and regular binary adders, without the requirement for modular adders. The presented design is faster than the latest introduced reverse converter for moduli set {2n, 2n–1, 2n–1–1}. Also, it has better performance than the reverse converters for the recently introduced moduli set {2n+1–1, 2n, 2n–1}
Abstract: An efficient parallel form in digital signal processor can improve the algorithm performance. The butterfly structure is an important role in fast Fourier transform (FFT), because its symmetry form is suitable for hardware implementation. Although it can perform a symmetric structure, the performance will be reduced under the data-dependent flow characteristic. Even though recent research which call as novel memory reference reduction methods (NMRRM) for FFT focus on reduce memory reference in twiddle factor, the data-dependent property still exists. In this paper, we propose a parallel-computing approach for FFT implementation on digital signal processor (DSP) which is based on data-independent property and still hold the property of low-memory reference. The proposed method combines final two steps in NMRRM FFT to perform a novel data-independent structure, besides it is very suitable for multi-operation-unit digital signal processor and dual-core system. We have applied the proposed method of radix-2 FFT algorithm in low memory reference on TI TMSC320C64x DSP. Experimental results show the method can reduce 33.8% clock cycles comparing with the NMRRM FFT implementation and keep the low-memory reference property.