Abstract: Subspace channel estimation methods have been
studied widely, where the subspace of the covariance matrix is
decomposed to separate the signal subspace from noise subspace. The
decomposition is normally done by using either the eigenvalue
decomposition (EVD) or the singular value decomposition (SVD) of
the auto-correlation matrix (ACM). However, the subspace
decomposition process is computationally expensive. This paper
considers the estimation of the multipath slow frequency hopping
(FH) channel using noise space based method. In particular, an
efficient method is proposed to estimate the multipath time delays by
applying multiple signal classification (MUSIC) algorithm which is
based on the null space extracted by the rank revealing LU (RRLU)
factorization. As a result, precise information is provided by the
RRLU about the numerical null space and the rank, (i.e., important
tool in linear algebra). The simulation results demonstrate the
effectiveness of the proposed novel method by approximately
decreasing the computational complexity to the half as compared
with RRQR methods keeping the same performance.
Abstract: The number of persons with implanted cardiac
pacemakers (PM) has increased in Western countries. The aim of this
paper is to investigate the possible situations where persons with a
PM may be exposed to extremely low frequency (ELF) electric (EF)
and magnetic fields (MF) that may disturb their PM. Based on our
earlier studies, it is possible to find such high public exposure to EFs
only in some places near 400 kV power lines, where an EF may
disturb a PM in unipolar mode. Such EFs cannot be found near 110
kV power lines. Disturbing MFs can be found near welding
machines. However, we do not have measurement data from welding.
Based on literature and earlier studies at Tampere University of
Technology, it is difficult to find public EF or MF exposure that is
high enough to interfere with PMs.
Abstract: The aim of this paper is to investigate accidents and
close call situations connected to the use of mobile phones in
working-age people ≥ 50 years old. The paper is part of a crosssectional
study that was carried out in 2002 in 15,000 working-age
Finns. The study showed that mobile-phone-related accidents and
close call situations, both at work and at leisure, are more common in
people under 50 years that in people ≥ 50 years old. However, people
under 50 use mobile phones more than those aged ≥ 50.
Abstract: Our globalizing world has become almost a small
village and everyone can access any information at any time.
Everyone lets each other know who does whatever in which place.
We can learn which social events occur in which place in the world.
From the perspective of education, the course notes that a lecturer use
in lessons in a university in any state of America can be examined by
a student studying in a city of Africa or the Far East. This dizzying
communication we have mentioned happened thanks to fast
developments in computer and internet technologies. While these
developments occur in the world, Turkey that has a very large young
population and whose electronic infrastructure rapidly improves has
also been affected by these developments. Nowadays, mobile devices
have become common and thus, it causes to increase data traffic in
social networks. This study was carried out on students in the
different age groups in Selcuk University Vocational School of
Technical Sciences, the Department of Computer Technology.
Students’ opinions about the use of internet and social media were
obtained. The features such as using the Internet and social media
skills, purposes, operating frequency, accessing facilities and tools,
social life and effects on vocational education and so forth were
explored. The positive effects and negative effects of both internet
and social media use on the students in this department and findings
are evaluated from different perspectives and results are obtained. In
addition, relations and differences were found out statistically.
Abstract: This paper presents experimental investigation and
finite element analysis on buckling behavior of irregular section coldformed
steel columns under axially concentric loading. For the
experimental study, four different sections of columns were tested to
investigate effect of stiffening and width-to-thickness ratio on
buckling behavior. For each of the section, three lengths of 230, 950
and 1900 mm. were studied representing short, intermediate long and
long columns, respectively. Then, nonlinear finite element analyses
of the tested columns were performed. The comparisons in terms of
load-deformation response and buckling mode show good agreement
and hence the FEM models were validated. Parametric study of
stiffening element and thickness of 1.0, 1.15, 1.2, 1.5, 1.6 and 2.0
mm. was analyzed. The test results showed that stiffening effect pays
a large contribution to prevent distortional mode. The increase in wall
thickness enhanced buckling stress beyond the yielding strength in
short and intermediate columns, but not for the long columns.
Abstract: Nanofibers of PVA /nickel nitrate/silica/alumina
izopropoxide/boric acid composite were prepared by using sol-gel
processing and electrospinning technique. By high temperature
calcinations of the above precursor fibers, nanofibers of
NiO/Al2O3/B2O3/SiO2 composite with diameters about 500 nm
could be successfully obtained. The fibers were characterized by
XRD and SEM analyses.
Abstract: Employer branding is considered as a useful tool for
addressing the global-local problem facing complex organisations
that have operations scattered across the globe and face challenges of
dealing with the local environment alongside. Despite being an
established field of study within the Western developed world, there
is little empirical evidence concerning the relevance of employer
branding to global companies that operate in the under-developed
economies. This paper fills this gap by gaining rich insight into the
implementation of employer branding programs in a foreign
multinational operating in Pakistan dealing with the global-local
problem. The study is qualitative in nature and employs semistructured
and focus group interviews with senior/middle managers
and local frontline employees to deeply examine the phenomenon in
case organisation. Findings suggest that authenticity is required in
employer brands to enable them to respond to the local needs thereby
leading to the resolution of the global-local problem. However, the
role of signaling theory is key to the development of authentic
employer brands as it stresses on the need to establish an efficient and
effective signaling environment where in signals travel in both
directions (from signal designers to receivers and backwards) and
facilitate firms with the global-local problem. The paper also
identifies future avenues of research for the employer branding field.
Abstract: High performance turf reinforcement mat (HPTRM) is
one of the most advanced flexible armoring technologies for severe
erosion challenges. The effect of turbulence on the slope stability of
an earthen levee strengthened by high performance turf reinforcement
mat (HPTRM) is investigated in this study for combined storm surge
and wave overtopping conditions. The results show that turbulence
has strong influence on the slope stability during the combined storm
surge and wave overtopping conditions. Among the surge height,
peak wave force and turbulent force. The turbulent force has the
ability to stabilize the earthen levee at the large wave force the
turbulent force has strongest effect on the FS. The surge storm acts as
an independent force on the slope stability of the earthen levee. It just
adds to the effects of the turbulent force and wave force on the slope
stability of HPTRM strengthened levee.
Abstract: It is well known that in recent years magnetic
materials have received increased attention due to their properties.
For this reason a significant number of patents that were published
during the last decade are oriented towards synthesis and study of
such materials. The aim of this work is to create and study ferrite
nanocrystalline materials with spinel structure, using sol-gel
technology with participation of auto-combustion. This method is
perspective in that it is a cheap and low-temperature technique that
allows for the fine control on the product’s chemical composition.
Abstract: In this study, polycaprolactone (PCL) was dissolved
in chloroform:ethanol solvent system at a concentration of 18 w/v %.
1, 2, 4, and 6 droplets of formic acid were added to the prepared 10ml
PCL-chloroform:ethanol solutions separately. Fibrous webs were
produced by electrospinning technique based on the horizontal
working principle. Morphology of the webs was investigated by
using scanning electron microscopy (SEM) whereas fiber diameters
were measured by Image J Software System. The effect of formic
acid addition to the mostly used chloroform solvent on fiber
morphology was examined.
Results indicate that there is a distinct fall in fiber diameter with
the addition of formic acid drops. The average fiber diameter was
measured as 2.22μm in PCL /chloroform:ethanol solution system. On
the other hand, 328nm and 256 nm average fiber diameters were
measured for the samples of 4 drops and 6 drops formic acid added.
This study offers alternative solvent systems to produce nanoscaled,
nontoxic PCL fibrous webs by electrospinning technique.
Abstract: In medical investigations, uncertainty is a major
challenging problem in making decision for doctors/experts to
identify the diseases with a common set of symptoms and also has
been extensively increasing in medical diagnosis problems. The
theory of cross entropy for intuitionistic fuzzy sets (IFS) is an
effective approach in coping uncertainty in decision making for
medical diagnosis problem. The main focus of this paper is to
propose a new intuitionistic fuzzy cross entropy measure (IFCEM),
which aid in reducing the uncertainty and doctors/experts will take
their decision easily in context of patient’s disease. It is shown that
the proposed measure has some elegant properties, which
demonstrates its potency. Further, it is also exemplified in detail the
efficiency and utility of the proposed measure by using a real life
case study of diagnosis the disease in medical science.
Abstract: The introduction of degradable plastic materials into
agricultural sectors has represented a promising alternative to
promote green agriculture and environmental friendly of modern
farming practices. Major challenges of developing degradable
agricultural films are to identify the most feasible types of
degradation mechanisms, composition of degradable polymers and
related processing techniques. The incorrect choice of degradable
mechanisms to be applied during the degradation process will cause
premature losses of mechanical performance and strength. In order to
achieve controlled process of agricultural film degradation, the
compositions of degradable agricultural film also important in order
to stimulate degradation reaction at required interval of time and to
achieve sustainability of the modern agricultural practices. A set of
photodegradable polyethylene based agricultural film was developed
and produced, following the selective optimization of processing
parameters of the agricultural film manufacturing system. Example of
agricultural films application for oil palm seedlings cultivation is
presented.
Abstract: This exploratory study gives an overview of the
evolution of the main financial and performance indicators of the
Academic Spin-Off’s and High Growth Academic Spin-Off’s in year
3 and year 6 after its creation in the region of Catalonia in Spain. The
study compares and evaluates results of these different measures of
performance and the degree of success of these companies for each
University.
We found that the average Catalonian Academic Spin-Off is small
and have not achieved the sustainability stage at year 6. On the
contrary, a small group of High Growth Academic Spin-Off’s
exhibits robust performance with high profits in year 6. Our results
support the need to increase selectivity and support for these
companies especially near year 3, because are the ones that will bring
wealth and employment. University role as an investor has rigid
norms and habits that impede an efficient economic return from their
ASO investment.
Universities with high performance on sales and employment in
year 3 not always could sustain this growth in year 6 because their
ASO’s are not profitable. On the contrary, profitable ASO exhibit
superior performance in all measurement indicators in year 6. We
advocate the need of a balanced growth (with profits) as a way to
obtain subsequent continuous growth.
Abstract: Co-crystal is believed to improve the solubility and
dissolution rates and thus, enhanced the bioavailability of poor water
soluble drugs particularly during the oral route of administration.
With the existing of poorly soluble drugs in pharmaceutical industry,
the screening of co-crystal formation using carbamazepine (CBZ) as
a model drug compound with dicarboxylic acids co-crystal formers
(CCF) namely fumaric (FA) and succinic (SA) acids in ethanol has
been studied. The co-crystal formations were studied by varying the
mol ratio values of CCF to CBZ to access the effect of CCF
concentration on the formation of the co-crystal. Solvent evaporation,
slurry and cooling crystallization which representing the solution
based method co-crystal screening were used. Based on the
differential scanning calorimetry (DSC) analysis, the melting point of
CBZ-SA in different ratio was in the range between 188oC-189oC.
For CBZ-FA form A and CBZ-FA form B the melting point in
different ratio were in the range of 174oC-175oC and 185oC-186oC
respectively. The product crystal from the screening was also
characterized using X-ray powder diffraction (XRPD). The XRPD
pattern profile analysis has shown that the CBZ co-crystals with FA
and SA were successfully formed for all ratios studied. The findings
revealed that CBZ-FA co-crystal were formed in two different
polymorphs. It was found that CBZ-FA form A and form B were
formed from evaporation and slurry crystallization methods
respectively. On the other hand, in cooling crystallization method,
CBZ-FA form A was formed at lower mol ratio of CCF to CBZ and
vice versa. This study disclosed that different methods and mol ratios
during the co-crystal screening can affect the outcome of co-crystal
produced such as polymorphic forms of co-crystal and thereof. Thus,
it was suggested that careful attentions is needed during the screening
since the co-crystal formation is currently one of the promising
approach to be considered in research and development for
pharmaceutical industry to improve the poorly soluble drugs.
Abstract: This paper describes an Action Research project
which was undertaken to inform professional practice in order to
develop a newly created Centre for Student Success in the specific
context of transnational medical and nursing education in the Middle
East. The objectives were to enhance the academic performance,
persistence, integration and personal and professional development of
a multinational study body, in particular in relation to pre-clinical
medical students, and to establish a comfortable, friendly and
student-driven environment within an Irish medical university
recently established in Bahrain. The outcomes of the project resulted
in the development of a specific student success ‘signature’ for this
particular transnational higher education context.
Abstract: A three-dimensional numerical model of
thermoelectric generator (TEG) modules attached to a large chimney
plate is proposed and solved numerically using a control volume based
finite difference formulation. The TEG module consists of a
thermoelectric generator, an elliptical pin-fin heat sink, and a cold
plate for water cooling. In the chimney, the temperature of flue gases is
450-650K. Although the TEG hot-side temperature and thus the
electric power output can be increased by inserting an elliptical pin-fin
heat sink into the chimney tunnel to increase the heat transfer area, the
pin fin heat sink would cause extra pumping power at the same time.
The main purpose of this study is to analyze the effects of geometrical
parameters on the electric power output and chimney pressure drop
characteristics. The effects of different operating conditions, including
various inlet velocities (Vin= 1, 3, 5 m/s), inlet temperatures (Tgas = 450,
550, 650K) and different fin height (0 to 150 mm) are discussed in
detail. The predicted numerical data for the power vs. current (P-I)
curve are in good agreement (within 11%) with the experimental data.
Abstract: Essential oils have a significant antimicrobial activity.
These oils can successfully replace the antibiotics. So, the
microorganisms show their inefficiencies resistant for the antibiotics.
For this reason, we study the physicochemical analysis and
antimicrobial activity of the essential oil of Daucus carota. The
extraction is done by steam distillation of water which brought us a
very significant return of 4.65%. The analysis of the essential oil is
performed by GC / MS and has allowed us to identify 32 compounds
in the oil of D. carota flowering tops of Bouira. Three of which are in
the majority are the α-Pinene (22.3%), the carotol (21.7%) and the
limonene (15.8%).
Abstract: Flash Floods, together with landslides, are a common
natural threat for people living in mountainous regions and foothills.
One way to deal with this constant menace is the use of Early
Warning Systems, which have become a very important mitigation
strategy for natural disasters.
In this work we present our proposal for a pilot Flash Flood Early
Warning System for Santiago, Chile, the first stage of a more
ambitious project that in a future stage shall also include early
warning of landslides.
To give a context for our approach, we first analyze three existing
Flash Flood Early Warning Systems, focusing on their general
architectures. We then present our proposed system, with main focus
on the decision support system, a system that integrates empirical
models and fuzzy expert systems to achieve reliable risk estimations.
Abstract: Today’s VLSI networks demands for high speed. And
in this work the compact form mathematical model for current mode
signalling in VLSI interconnects is presented.RLC interconnect line
is modelled using characteristic impedance of transmission line and
inductive effect. The on-chip inductance effect is dominant at lower
technology node is emulated into an equivalent resistance. First order
transfer function is designed using finite difference equation, Laplace
transform and by applying the boundary conditions at the source and
load termination. It has been observed that the dominant pole
determines system response and delay in the proposed model. The
novel proposed current mode model shows superior performance as
compared to voltage mode signalling. Analysis shows that current
mode signalling in VLSI interconnects provides 2.8 times better
delay performance than voltage mode. Secondly the damping factor
of a lumped RLC circuit is shown to be a useful figure of merit.
Abstract: Applications of the Hausdorff space and its mappings
into tangent spaces are outlined, including their fractal dimensions
and self-similarities. The paper details this theory set up and further
describes virtualizations and atomization of manufacturing processes.
It demonstrates novel concurrency principles that will guide
manufacturing processes and resources configurations. Moreover,
varying levels of details may be produced by up folding and breaking
down of newly introduced generic models. This choice of layered
generic models for units and systems aspects along specific aspects
allows research work in parallel to other disciplines with the same
focus on all levels of detail. More credit and easier access are granted
to outside disciplines for enriching manufacturing grounds. Specific
mappings and the layers give hints for chances for interdisciplinary
outcomes and may highlight more details for interoperability
standards, as already worked on the international level. The new rules
are described, which require additional properties concerning all
involved entities for defining distributed decision cycles, again on the
base of self-similarity. All properties are further detailed and assigned
to a maturity scale, eventually displaying the smartness maturity of a
total shopfloor or a factory. The paper contributes to the intensive
ongoing discussion in the field of intelligent distributed
manufacturing and promotes solid concepts for implementations of
Cyber Physical Systems and the Internet of Things into
manufacturing industry, like industry 4.0, as discussed in German-speaking
countries.