Abstract: Fluid viscous damping systems are well suited for
many air vehicles subjected to shock and vibration. These damping
system work with the principle of viscous fluid throttling through the
orifice to create huge pressure difference between compression and
rebound chamber and obtain the required damping force. One
application of such systems is its use in aircraft door system to
counteract the door’s velocity and safely stop it. In exigency
situations like crash or emergency landing where the door doesn’t
open easily, possibly due to unusually tilting of fuselage or some
obstacles or intrusion of debris obstruction to move the parts of the
door, such system can be combined with other systems to provide
needed force to forcefully open the door and also securely stop it
simultaneously within the required time i.e. less than 8 seconds. In
the present study, a hydraulic system called snubber along with other
systems like actuator, gas bottle assembly which together known as
emergency power assist system (EPAS) is designed, built and
experimentally studied to check the magnitude of angular velocity,
damping force and time required to effectively open the door.
Whenever needed, the gas pressure from the bottle is released to
actuate the actuator and at the same time pull the snubber’s piston to
operate the emergency opening of the door. Such EPAS installed in
the suspension arm of the aircraft door is studied explicitly changing
parameters like orifice size, oil level, oil viscosity and bypass valve
gap and its spring of the snubber at varying temperature to generate
the optimum design case. Comparative analysis of the EPAS at
several cases is done and conclusions are made. It is found that
during emergency condition, the system opening time and angular
velocity, when snubber with 0.3mm piston and shaft orifice and
bypass valve gap of 0.5 mm with its original spring is used, shows
significant improvement over the old ones.
Abstract: Remote sensing plays a vital role in mapping of
resources and monitoring of environments of the earth. In the present
research study, mapping and monitoring of clay siltations occurred in
the Alkhod Dam of Muscat, Sultanate of Oman are carried out using
low-cost multispectral Landsat and ASTER data. The dam is
constructed across the Wadi Samail catchment for ground water
recharge. The occurrence and spatial distribution of siltations in the
dam are studied with five years of interval from the year 1987 of
construction to 2014. The deposits are mainly due to the clay, sand
and silt occurrences derived from the weathering rocks of ophiolite
sequences occurred in the Wadi Samail catchment. The occurrences
of clays are confirmed by minerals identification using ASTER
VNIR-SWIR spectral bands and Spectral Angle Mapper supervised
image processing method. The presence of clays and their spatial
distribution are verified in the field. The study recommends the
technique and the low-cost satellite data to similar region of the
world.
Abstract: This study investigates the cleaning performance of
high intensity 360 kHz frequency on removal of nano-dimensional
and sub-micron particles from various surfaces, uniformity of the
cleaning tank and run to run variation of cleaning process. The
uniformity of the cleaning tank was measured by two different
methods i.e. 1. ppbTM meter and 2. Liquid Particle Counting (LPC)
technique. The result indicates that the energy was distributed more
uniformly throughout the entire cleaning vessel even at the corners
and edges of the tank when megasonic sweeping technology is
applied. The result also shows that rinsing the parts with 360 kHz
frequency at final rinse gives lower particle counts, hence higher
cleaning efficiency as compared to other frequencies. When
megasonic sweeping technology is applied each piezoelectric
transducers will operate at their optimum resonant frequency and
generates stronger acoustic cavitational force and higher acoustic
streaming velocity. These combined forces are helping to enhance the
particle removal and at the same time improve the overall cleaning
performance. The multiple extractions study was also carried out for
various frequencies to measure the cleaning potential and asymptote
value.
Abstract: Waxapple (Syzygium samarngense Merr.et Perry) is an
important tropical fruit in Taiwan. The famous producing area is
located on the coast in Pingtung County. Land subsidence and climate
change will tend to soil alkalization more seriously. This study was to
evaluate the effects of NaCl in waxapple seedlings. NaCl salinity
reduced waxapple shoot growth; it may due to reducing relative water
content in leaf and new shoot. Leaf Cl and Na concentration were
increased but K, Ca, and Mg content had no significant difference after
irrigated with NaCl for six weeks. In roots, Na and Cl content increase
significantly with 90 mM NaCl treatment, but K, Ca, and Mg content
was reduced. 30-90mM Nacl treatment do not effect K/Na, Ca/Na and
Mg/Na ratio, but decrease significantly in 90mM treatment in roots.
The leaf and root electrolyte leakage were significantly affected by 90
mM NaCl treatment. Suggesting 90mM was optimum concentration
for sieve out other tolerance waxapples verities.
Abstract: The research studies the behaviors based on
sufficiency economy philosophy at individual and community
levelsas well as the satisfaction of the urban community leaders by
collecting data with purposive sampling technique. For in-depth
interviews with 26 urban community leaders, the result shows that
the urban community leaders have good knowledge and
understanding about sufficiency economy philosophy. Especially in
terms of money spending, they must consider the need for living and
be economical. The activities in the community or society should not
take advantage of the others as well as colleagues. At present, most of
the urban community leaders live in sufficient way. They often spend
time with public service, but many families are dealing with debt.
Many communities have some political conflict and high family
allowances because of living in the urban communities with rapid
social and economic changes. However, there are many communities
that leaders have applied their wisdom in development for their
people by gathering and grouping the professionals to form activities
such as making chilli sauce, textile organization, making artificial
flowers to worship the sanctity. The most prominent group is the foot
massage business in Wat Pracha Rabue Tham. This professional
group is supported continuously by the government. One of the
factors in terms of satisfaction used for evaluating community leaders
is the customary administration in brotherly, interdependent way
rather than using the absolute power or controlling power, but using
the roles of leader to perform the activities with their people intently,
determinedly and having public mind for people.
Abstract: The pullout strength had an effect on the stability of
plate screw fixation when inserted in the cervical spine. Nine
different titanium alloy bone screws were used to test the pullout
strength through finite element analysis. The result showed that the
Moss Miami I can bear the highest pullout force at 1,075 N, which
causes the maximum von Mises stress at 858.87 MPa, a value over
the yield strength of titanium. The bone screw should have large
outer diameter, core diameter and proximal root radius to increase the
pullout strength.
Abstract: The characteristic requirement for producing
rectangular shape bottles was a uniform thickness of the plastic bottle
wall. Die shaping was a good technique which controlled the wall
thickness of bottles. An advance technology which was the finite
element method (FEM) for blowing parison to be a rectangular shape
bottle was conducted to reduce waste plastic from a trial and error
method of a die shaping and parison control method. The artificial
intelligent (AI) comprised of artificial neural network and genetic
algorithm was selected to optimize the die gap shape from the FEM
results. The application of AI technique could optimize the suitable
die gap shape for the parison blow molding which did not depend on
the parison control method to produce rectangular bottles with the
uniform wall. Particularly, this application can be used with cheap
blow molding machines without a parison controller therefore it will
reduce cost of production in the bottle blow molding process.
Abstract: Various personality profile tests are used to identify
personality strengths and limits in individuals, helping both
individuals and managers to optimize work and team effort in
organizations. One such test, the Hartman’s personality profile,
emphasizes four driving "core motives" influenced or affected by
both strengths and limitations classified into four colors: Red -
motivated by power; Blue - discipline and loyalty; White - peace; and
Yellow – fun loving. Two shortcomings of Hartman’s personality test
are noted; 1) only one selection for every item / situation allowed and
2) selection of an item / option even if not applicable. A test taker
may be as much nurturing as he is opinionated but since
“opinionated” seems less attractive the individual would likely select
nurturing, causing a misidentification in personality strengths and
limits. Since few individuals have a “strong” personality, it is
difficult to assess their true personality strengths and limits allowing
only one choice or requiring unwanted choices, undermining the
potential of the test. We modified Hartman’s personality profile
allowing test takers to make either multiple choices for any item /
situation or leave them blank if applicable. Sixty-eight participants
(38 males and 30 females), 17 - 49 years old, from countries in Asia,
Europe, N. America, CIS, Africa, Latin America, and Oceania were
included. 58 participants (85.3%) reported the modified test, allowing
multiple / no choices better identified their personality strengths and
limits, while 10 participants (14.7%) expressed the original (one
choice version) was sufficient. The overall results show that our
modified test enhanced the identification and balance of core
personalities’ strengths and limits, aiding test takers, managers and
organizations to better assess individual characteristics, particularly
useful in making task-related, teamwork, and management decisions.
Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: The organizations in the knowledge economy era have
recognized the importance of building knowledge assets for
sustainable growth and development. In comparison to other
industries, Information Technology (IT) enterprises, holds an edge in
developing an effective Knowledge Management (KM) programmethanks
to their in-house technological abilities. This paper tries to
study the various knowledge based incentive programmes and its
effect on Knowledge Sharing and Learning in the context of the
Indian IT sector. A conceptual model is developed linking KM
Incentives, Knowledge Sharing and Learning. A questionnaire study
is conducted to collect primary data from the knowledge workers of
the IT organizations located in India. The data was analysed using
Structural Equation Modeling using Partial Least Square method. The
results show a strong influence of knowledge management incentives
on knowledge sharing and an indirect influence on learning.
Abstract: Environmental impact assessment techniques have
been developed as a result of the worldwide efforts to reduce the
environmental impact of global warming. By using the quantification
method in the construction industry, it is now possible to manage the
greenhouse gas is to systematically evaluate the impact on the
environment over the entire construction process. In particular, the
proportion of greenhouse gas emissions at the production stage of
construction material occupied is high, and efforts are needed in
particular in the construction field.
In this research, intended for concrete products for the construction
materials, by using the LCA method, we compared the results of
environmental impact assessment and carbon emissions of developing
products that have been applied low-carbon technologies compared to
existing products. As a results, by introducing a raw material of
industrial waste, showed carbon reduction. Through a comparison of
the carbon emission reduction effect of low carbon technologies, it is
intended to provide academic data for the evaluation of greenhouse
gases in the construction sector and the development of low carbon
technologies of the future.
Abstract: The wear measuring and wear modelling are
fundamental issues in the industrial field, mainly correlated to the
economy and safety. Therefore, there is a need to study the wear
measurements and wear estimation. Pin-on-disc test is the most
common test which is used to study the wear behaviour. In this paper,
the pin-on-disc (AEROTECH UNIDEX 11) is used for the
investigation of the effects of normal load and hardness of material on
the wear under dry and sliding conditions. In the pin-on-disc rig, two
specimens were used; one, a pin is made of steel with a tip, positioned
perpendicular to the disc, where the disc is made of aluminium. The
pin wear and disc wear were measured by using the following
instruments: The Talysurf instrument, a digital microscope, and the
alicona instrument. The Talysurf profilometer was used to measure
the pin/disc wear scar depth, digital microscope was used to measure
the diameter and width of wear scar, and the alicona was used to
measure the pin wear and disc wear. After that, the Archard model,
American Society for Testing and Materials model (ASTM), and
neural network model were used for pin/disc wear modelling.
Simulation results were implemented by using the Matlab program.
This paper focuses on how the alicona can be used for wear
measurements and how the neural network can be used for wear
estimation.
Abstract: This study evaluated the use of raw or processed
Prosopis juliflora (Meskit) pods as a major ingredient in a formulated
ration to provide an alternative non-conventional concentrate for
livestock feeding in Oman. Dry Meskit pods were reduced to lengths
of 0.5- 1.0 cm to ensure thorough mixing into three diets. Meskit
pods were subjected to two types of treatments; roasting and soaking.
They were roasted at 150оC for 30 minutes using a locally-made
roasting device (40 kg barrel container rotated by electric motor and
heated by flame gas cooker). Chopped pods were soaked in tap water
for 24 hours and dried for 2 days under the sun with frequent turning.
The Meskit-pod-based diets (MPBD) were formulated and pelleted
from 500 g/kg ground Meskit pods, 240 g/kg wheat bran, 200 g/kg
barley grain, 50 g/kg local dried sardines and 10 g/kg of salt. Twenty
four 10 months-old intact Omani male lambs with average body
weight of 27.3 kg (± 0.5 kg) were used in a feeding trial for 84 days.
They were divided (on body weight basis) and allocated to four diet
combination groups. These were: Rhodes grass hay (RGH) plus a
general ruminant concentrate (GRC); RGH plus raw Meskit pods
(RMP) based concentrate; RGH plus roasted Meskit pods (ROMP)
based concentrate; RGH plus soaked Meskit pods (SMP) based
concentrate Daily feed intakes and bi-weekly body weights were
recorded. MPBD had higher contents of crude protein (CP), acid
detergent fibre (ADF) and neutral detergent fibre (NDF) than the
GRC. Animals fed various types of MPBD did not show signs of ill
health. There was a significant effect of feeding ROMP on the
performance of Omani sheep compared to RMP and SMP. The
ROMP fed animals had similar performance to those fed the GRC in
terms of feed intake, body weight gain and feed conversion ratio
(FCR).This study indicated that roasted Meskit pods based diet may
be used instead of the commercial concentrate for feeding Omani
sheep without adverse effects on performance. It offers a cheap
alternative source of protein and energy for feeding Omani sheep.
Also, it might help in solving the spread impact of Meskit trees,
maintain the ecosystem and helping in preserving the local tree
species.
Abstract: In this paper, we propose an intelligent system that is
used for monitoring the health conditions of patients. Monitoring the
health condition of patients is a complex problem that involves
different medical units and requires continuous monitoring especially
in rural areas because of inadequate number of available specialized
physicians. The proposed system will improve patient care and drive
costs down comparing to the existing system in Jordan. The proposed
system will be the start point to faster and improve the
communication between different units in the health system in
Jordan. Connecting patients and their physicians beyond hospital
doors regarding their geographical area is an important issue in
developing the health system in Jordan. The ability of making
medical decisions, the quality of medical is expected to be improved.
Abstract: The aim of this paper is to perform experimental
modal analysis (EMA) of reinforced concrete (RC) square slabs.
EMA is the process of determining the modal parameters (Natural
Frequencies, damping factors, modal vectors) of a structure from a
set of frequency response functions FRFs (curve fitting). Although,
experimental modal analysis (or modal testing) has grown steadily in
popularity since the advent of the digital FFT spectrum analyzer in
the early 1970’s, studying all types of members and materials using
such method have not yet been well documented. Therefore, in this
work, experimental tests were conducted on RC square slab
specimens of dimensions 600mm x 600mmx 40mm. Experimental
analysis was based on freely supported boundary condition.
Moreover, impact testing as a fast and economical means of finding
the modes of vibration of a structure was used during the
experiments. In addition, Pico Scope 6 device and MATLAB
software were used to acquire data, analyze and plot Frequency
Response Function (FRF). The experimental natural frequencies
which were extracted from measurements exhibit good agreement
with analytical predictions. It is showed that EMA method can be
usefully employed to investigate the dynamic behavior of RC slabs.
Abstract: As the use of geothermal energy grows internationally
more effort is required to monitor and protect areas with rare and
important geothermal surface features. A number of approaches are
presented for developing and calibrating numerical geothermal
reservoir models that are capable of accurately representing
geothermal surface features. The approaches are discussed in the
context of cases studies of the Rotorua geothermal system and the
Orakei-korako geothermal system, both of which contain important
surface features. The results show that models are able to match the
available field data accurately and hence can be used as valuable
tools for predicting the future response of the systems to changes in
use.
Abstract: This paper presents small signal stability study carried
over the 140-Bus, 31-Machine, 5-Area MEPE system and validated
on free and open source software: PSAT. Well-established linearalgebra
analysis, eigenvalue analysis, is employed to determine the
small signal dynamic behavior of test system. The aspects of local
and interarea oscillations which may affect the operation and
behavior of power system are analyzed. Eigenvalue analysis is carried
out to investigate the small signal behavior of test system and the
participation factors have been determined to identify the
participation of the states in the variation of different mode shapes.
Also, the variations in oscillatory modes are presented to observe the
damping performance of the test system.
Abstract: The main aim of this article is to present a balance of the decade of Polish air transport market in the European Union having taking into account selected entities of the aviation market. This article analyzes the functioning of the Polish air transport market after the Polish accession to the European Union. During the study two main areas were pointed: shipping activity and activity of the airports. The most important benefits of integration and the benefits of introducing of the open sky policy were indicated. The last part of the article presents the perspectives of development of air traffic.
Abstract: The concept of urban transformation came about
through interventions aimed at bringing socially and economically
problematic areas of cities into use. The issue of urban transformation
arose frequently during the post-2000 period in particular, and legal
regulations on this matter were also developed in Turkey. Urban
transformation project would be a focal point for the formation of the
city in the near future. Izmir, which is third largest city of Turkey, is
an important trade and port city. But, assessment of the current
situation shows that, the majority of existing residential areas was
formed with squatters and unplanned settlements in Izmir city center.
Therefore an important part of these areas have significant problems
in terms of the quality of life, safety and environmental quality. In
this study, the central policies in Turkey and local policies in Đzmir
about urban transformation will be considered. In addition, urban
renewal projects that are being implemented in Izmir were discussed
and suggestions will be developed in accordance with this policy.
Abstract: Logistics processes of perishable food in the supply
chain include the distribution activities and the real time temperature
monitoring to fulfil the cold chain requirements. The paper presents
the use of RFID (Radio Frequency Identification) technology as an
identification tool of receiving and shipping activities in the cold
store. At the same time, the use of RFID data loggers with
temperature sensors is presented to observe and store the
temperatures for the purpose of analyzing the processes and having
the history data available for traceability purposes and efficient recall
management.