Abstract: Zeolite A and MCM-41 have extensive applications in basic science, petrochemical science, energy conservation/storage, medicine, chemical sensor, air purification, environmentally benign composite structure and waste remediation. However, the use of zeolite A and MCM-41 in these areas, especially environmental remediation, are restricted due to prohibitive production cost. Efficient recycling of and resource recovery from coal fly ash has been a major topic of current international research interest, aimed at achieving sustainable development of human society from the viewpoints of energy, economy, and environmental strategy. This project reported an original, novel, green and fast methods to produce nano-porous zeolite A and MCM-41 materials from coal fly ash. For zeolite A, this novel production method allows a reduction by half of the total production time while maintaining a high degree of crystallinity of zeolite A which exists in a narrower particle size distribution. For MCM-41, this remarkably green approach, being an environmentally friendly process and reducing generation of toxic waste, can produce pure and long-range ordered MCM-41 materials from coal fly ash. This approach took 24 h at 25 oC to produce 9 g of MCM-41 materials from 30 g of the coal fly ash, which is the shortest time and lowest reaction temperature required to produce pure and ordered MCM-41 materials (having the largest internal surface area) compared to the values reported in the literature. Performance evaluation of the produced zeolite A and MCM-41 materials in wastewater treatment and air pollution control were reported. The residual fly ash was also converted to zeolite Na-P1 which showed good performance in removal of multi-metal ions in wastewater. In wastewater treatment, compared to commercial-grade zeolite A, adsorbents produced from coal fly ash were effective in removing multi heavy metal ions in water and could be an alternative material for treatment of wastewater. In methane emission abatement, the zeolite A (produced from coal fly ash) achieved similar methane removal efficiency compared to the zeolite A prepared from pure chemicals. This report provides the guidance for production of zeolite A and MCM-41 from coal fly ash by a cost-effective approach which opens potential applications of these materials in environmental industry. Finally, environmental and economic aspects of production of zeolite A and MCM-41 from coal fly ash were discussed.
Abstract: Money laundering has been described by many as the lifeblood of crime and is a major threat to the economic and social well-being of societies. It has been recognized that the banking system has long been the central element of money laundering. This is in part due to the complexity and confidentiality of the banking system itself. It is generally accepted that effective anti-money laundering (AML) measures adopted by banks will make it tougher for criminals to get their "dirty money" into the financial system. In fact, for law enforcement agencies, banks are considered to be an important source of valuable information for the detection of money laundering. However, from the banks- perspective, the main reason for their existence is to make as much profits as possible. Hence their cultural and commercial interests are totally distinct from that of the law enforcement authorities. Undoubtedly, AML laws create a major dilemma for banks as they produce a significant shift in the way banks interact with their customers. Furthermore, the implementation of the laws not only creates significant compliance problems for banks, but also has the potential to adversely affect the operations of banks. As such, it is legitimate to ask whether these laws are effective in preventing money launderers from using banks, or whether they simply put an unreasonable burden on banks and their customers. This paper attempts to address these issues and analyze them against the background of the Malaysian AML laws. It must be said that effective coordination between AML regulator and the banking industry is vital to minimize problems faced by the banks and thereby to ensure effective implementation of the laws in combating money laundering.
Abstract: In this empirical research, how marketing managers evaluate their firms- performances and decide to make innovation is examined. They use some standards which are past performance of the firm, target performance of the firm, competitor performance, and average performance of the industry to compare and evaluate the firms- performances. It is hypothesized that marketing managers and owners of the firm compare the firms- current performance with these four standards at the same time to decide when to make innovation relating to any aspects of the firm, either management style or products. Relationship between the comparison of the firm-s performance with these standards and innovation are searched in the same regression model. The results of the regression analysis are discussed and some recommendations are made for future studies and applicants.
Abstract: Jordan exerts many efforts to nurture their academically gifted students in special schools since 2001. During
the past nine years of launching these schools, their learning and excellence environments were believed to be distinguished compared
to public schools. This study investigated the environments of gifted
students compared with other non-gifted, using a survey instrument
that measures the dimensions of family, peers, teachers, school- support, society, and resources –dimensions rooted deeply in supporting gifted education, learning, and achievement. A total
number of 109 were selected from excellence schools for
academically gifted students, and 119 non-gifted students were selected from public schools. Around 8.3% of the non-gifted students
reported that they “Never" received any support from their surrounding environments, 14.9% reported “Seldom" support, 23.7% reported “ Often" support, 26.0% reported “Frequent" support, and
32.8% reported “Very frequent" support. Where the gifted students reported more “Never" support than the non-gifted did with 11.3%,
“Seldom" support with 15.4%, “Often" support with 26.6%,
“Frequent" support with 29.0%, and reported “Very frequent" support less than the non-gifted students with 23.6%. Unexpectedly,
statistical differences were found between the two groups favoring
non-gifted students in perception of their surrounding environments
in specific dimensions, namely, school- support, teachers, and society. No statistical differences were found in the other dimensions
of the survey, namely, family, peers, and resources. As the
differences were found in teachers, school- support, and society, the
nurturing environments for the excellence schools need to be revised to adopt more creative teaching styles, rich school atmosphere and
infrastructures, interactive guiding for the students and their parents, promoting for the excellence environments, and re-build successful
identification models. Thus, families, schools, and society should
increase their cooperation, communication, and awareness of the
gifted supportive environments. However, more studies to investigate
other aspects of promoting academic giftedness and excellence are recommended.
Abstract: The ever growing sentiment of environmentalism across the globe has made many people think on the green lines. But most of such ideas halt short of implementation because of the short term economic viability issues with the concept of going green. In this paper we have tried to amalgamate the green concept with social entrepreneurship for solving a variety of issues faced by the society today. In addition the paper also tries to ensure that the short term economic viability does not act as a deterrent. The paper comes up three sustainable models of social entrepreneurship which tackle a wide assortment of issues such as nutrition problem, land problems, pollution problems and employment problems. The models described fall under the following heads: - Spirulina cultivation: The model addresses nutrition, land and employment issues. It deals with cultivation of a blue green alga called Spirulina which can be used as a very nutritious food. Also, the implementation of this model would bring forth employment to the poor people of the area. - Biocomposites: The model comes up with various avenues in which biocomposites can be used in an economically sustainable manner. This model deals with the environmental concerns and addresses the depletion of natural resources. - Packaging material from empty fruit bunches (EFB) of oil palm: This one deals with air and land pollution. It is intended to be a substitute for packaging materials made from Styrofoam and plastics which are non-biodegradable. It takes care of the biodegradability and land pollution issues. It also reduces air pollution as the empty fruit bunches are not incinerated. All the three models are sustainable and do not deplete the natural resources any further. This paper explains each of the models in detail and deals with the operational/manufacturing procedures and cost analysis while also throwing light on the benefits derived and sustainability aspects.
Abstract: Partitioning is a critical area of VLSI CAD. In order to build complex digital logic circuits its often essential to sub-divide multi -million transistor design into manageable Pieces. This paper looks at the various partitioning techniques aspects of VLSI CAD, targeted at various applications. We proposed an evolutionary time-series model and a statistical glitch prediction system using a neural network with selection of global feature by making use of clustering method model, for partitioning a circuit. For evolutionary time-series model, we made use of genetic, memetic & neuro-memetic techniques. Our work focused in use of clustering methods - K-means & EM methodology. A comparative study is provided for all techniques to solve the problem of circuit partitioning pertaining to VLSI design. The performance of all approaches is compared using benchmark data provided by MCNC standard cell placement benchmark net lists. Analysis of the investigational results proved that the Neuro-memetic model achieves greater performance then other model in recognizing sub-circuits with minimum amount of interconnections between them.
Abstract: The paper deals with the analysis of triggering
conditions and evolution processes of piping phenomena, in relation
to both mechanical and hydraulic aspects. In particular, the aim of
the study is to predict slope instabilities triggered by piping,
analysing the conditions necessary for a flow failure to occur. Really,
the mechanical effect involved in the loads redistribution around the
pipe is coupled to the drainage process arising from higher
permeability of the pipe. If after the pipe formation, the drainage
goes prevented for pipe clogging, the porewater pressure increase can
lead to the failure or even the liquefaction, with a subsequent flow
slide. To simulate the piping evolution and to verify relevant stability
conditions, a iterative coupled modelling approach has been pointed
out. As example, the proposed tool has been applied to the Stava
Valley disaster (July, 1985), demonstrating that piping might be one
of triggering phenomena of the tailings dams collapse.
Abstract: Twelve lactating Etawah Crossedbred goats were used
in this study. Goat feed consisted of Cally andra callothyrsus,
Pennisetum purpureum, wheat bran and dried fermented cassava
peel. The cassava peels were fermented with a traditional culture
called “ragi tape" (mixed culture of Saccharomyces cerevisae,
Aspergillus sp, Candida, Hasnula and Acetobacter). The goats were
divided into 2 groups (Control and Treated) of six does. The
experimental diet of the Control group consisted of 70% of roughage
(fresh Callyandra callothyrsus and Pennisetum purpureum 60:40)
and 30% of wheat bran on dry matter (DM) base. In the Treated
group 30% of wheat bran was replaced with dried fermented cassava
peels. Data were statistically analyzed using analysis of variance
followed SPSS program. The concentration of HCN in fermented
cassava peel decreased to non toxic level. Nutrient composition of
dried fermented cassava peel consisted of 85.75% dry matter;
5.80% crude protein and 82.51% total digestible nutrien (TDN).
Substitution of 30% of wheat bran with dried fermented cassava peel
in the diet had no effect on dry matter and organic matter intake but
significantly (P< 0.05) decreased crude protein and TDN
consumption as well as milk yields and milk composition. The study
recommended to reduced the level of substitution to less than 30% of
concentrates in the diet in order to avoid low nutrient intake and milk
production of goats.
Abstract: Physical and mechanical properties of Russian olive
fruits were measured at moisture content of 14.43% w.b. The results
revealed that the mean length, width and thickness of Russian olive
fruits were 20.72, 15.73 and 14.69mm, respectively. Mean mass and
volume of Russian olive fruits were measured as 1.45 g and 2.55 cm3,
respectively. The sphericity, aspect ratio and surface area were
calculated as 0.81, 0.72 and 8.96 cm2, respectively, while arithmetic
mean diameter, geometric mean diameter and equivalent diameter of
Russian olive fruits were 17.05, 16.83 and 16.84 mm, respectively.
Whole fruit density, bulk density and porosity of jujube fruits were
measured and found to be 1.01 g/cm3, 0.29 g/cm3 and 69.5%,
respectively. The values of static coefficient of friction on three
surfaces of glass, galvanized iron and plywood were 0.35, 0.36 and
0.43, respectively. The skin color (L*, a*, b*) varied from 9.92 to
16.08; 2.04 to 3.91 and 1.12 to 3.83, respectively. The values of
rupture force, deformation, energy absorbed and hardness were found
to be between 12.14-16.85 N, 2.16-4.25 mm, 3.42-6.99 N mm and
17.1-23.85 N/mm.
Abstract: The paper provides a discussion of the most relevant
aspects of yield curve modeling. Two classes of models are
considered: stochastic and parsimonious function based, through the
approaches developed by Vasicek (1977) and Nelson and Siegel
(1987). Yield curve estimates for Croatia are presented and their
dynamics analyzed and finally, a comparative analysis of models is
conducted.
Abstract: In this work, several ASP solutions were flooded into
fractured models initially saturated with heavy oil at a constant flow
rate and different geometrical characteristics of fracture. The ASP
solutions are constituted from 2 polymers i.e. a synthetic polymer,
hydrolyzed polyacrylamide as well as a biopolymer, a surfactant and
2types of alkaline. The results showed that using synthetic
hydrolyzed polyacrylamide polymer increases ultimate oil recovery;
however, type of alkaline does not play a significant rule on oil
recovery. In addition, position of the injection well respect to the
fracture system has remarkable effects on ASP flooding. For instance
increasing angle of fractures with mean flow direction causes more
oil recovery and delays breakthrough time. This work can be
accounted as a comprehensive survey on ASP flooding which
considers most of effective factors in this chemical EOR method.
Abstract: Medical image data hiding has strict constrains such
as high imperceptibility, high capacity and high robustness.
Achieving these three requirements simultaneously is highly
cumbersome. Some works have been reported in the literature on
data hiding, watermarking and stegnography which are suitable for
telemedicine applications. None is reliable in all aspects. Electronic
Patient Report (EPR) data hiding for telemedicine demand it blind
and reversible. This paper proposes a novel approach to blind
reversible data hiding based on integer wavelet transform.
Experimental results shows that this scheme outperforms the prior
arts in terms of zero BER (Bit Error Rate), higher PSNR (Peak Signal
to Noise Ratio), and large EPR data embedding capacity with
WPSNR (Weighted Peak Signal to Noise Ratio) around 53 dB,
compared with the existing reversible data hiding schemes.
Abstract: This paper discusses the applicability of the Data
Distribution Service (DDS) for the development of automated and modular manufacturing systems which require a flexible and robust
communication infrastructure. DDS is an emergent standard for datacentric publish/subscribe middleware systems that provides an
infrastructure for platform-independent many-to-many
communication. It particularly addresses the needs of real-time systems that require deterministic data transfer, have low memory
footprints and high robustness requirements. After an overview of the
standard, several aspects of DDS are related to current challenges for the development of modern manufacturing systems with distributed architectures. Finally, an example application is presented based on a modular active fixturing system to illustrate the described aspects.
Abstract: The computer modeling is carried out for parameter of
sensitivity of optoelectronic chemical and biosensors, using
phenomena of surface plasmon resonance (SPR). The physical model
of SPR-sensor-s is described with (or without) of modifications of
sensitive gold film surface by a dielectric layer. The variants of
increasing of sensitivity for SPR-biosensors, constructed on the
principle gold – dielectric – biomolecular layer are considered. Two
methods of mathematical treatment of SPR-curve are compared –
traditional, with estimation of sensor-s response as shift of the SPRcurve
minimum and proposed, for system with dielectric layer, using
calculating of the derivative in the point of SPR-curve half-width.
Abstract: The aim of present study was to assess the effect of
glucogenic (G) and lipogenic (L) diets on blood metabolites in
Baloochi lambs. Three rumen cannulated Baloochi sheep were used
as a 3×3 Latin square design with 3 periods (28 days). Experimental
diets were a glucogenic, a lipogenic and a mixture of G and L diets
(50:50). The animals were fed diets consisted of 50% chopped alfalfa
hay and 50% concentrate. Diets were fed once daily ad libitum.
Blood samples were taken from jugular vein before the feeding, 2, 4
and 6 hour post feeding at day 27. Results indicated that β-
hydroxybutyrate (BHBA), glucose, insulin and aspartate
aminotransferase (AST) were not affected by treatments (P > 0.05).
However, lipogenic diet increased significantly activity of Alanine
aminotransferase (ALT) and concentration of non-esterified fatty acid
(NEFA) in blood plasma (P < 0.05)
Abstract: In this work, the precipitation of asphaltene from a Malaysian light oil reservoir was studies. A series of experiments were designed and carried out to examine the effect of CO2 injection on asphaltene precipitation. Different pressures of injections were used in Dynamic flooding experiment in order to investigate the effect of pressure versus injection pore volume of CO2. These dynamic displacement tests simulate reservoir condition. Results show that by increasing the pore volume of injected gas asphaltene precipitation will increases, also rise in injection pressure causes less precipitation. Sandstone core plug was used to represent reservoir formation during displacement test; therefore it made it possible to study the effect of present of asphaltene on formation. It is found out that the precipitated asphaltene can reduce permeability and porosity which is not favorable during oil production.
Abstract: This paper includes a positive analysis to quantitatively grasp the relationship among vulnerability, information security incidents, and the countermeasures by using data based on a 2007 questionnaire survey for Japanese ISPs (Internet Service Providers). To grasp the relationships, logistic regression analysis is used. The results clarify that there are relationships between information security incidents and the countermeasures. Concretely, there is a positive relationship between information security incidents and the number of information security systems introduced as well as a negative relationship between information security incidents and information security education. It is also pointed out that (especially, local) ISPs do not execute efficient information security countermeasures/ investment concerned with systems, and it is suggested that they should positively execute information security education. In addition, to further heighten the information security level of Japanese telecommunication infrastructure, the necessity and importance of the government to implement policy to support the countermeasures of ISPs is insisted.
Abstract: In this paper, the local grid refinement is focused by
using a nested grid technique. The Cartesian grid numerical method is
developed for simulating unsteady, viscous, incompressible flows
with complex immersed boundaries. A finite volume method is used in
conjunction with a two-step fractional-step procedure. The key aspects
that need to be considered in developing such a nested grid solver are
imposition of interface conditions on the inter-block and accurate
discretization of the governing equation in cells that are with the
inter-block as a control surface. A new interpolation procedure is
presented which allows systematic development of a spatial
discretization scheme that preserves the spatial accuracy of the
underlying solver. The present nested grid method has been tested by
two numerical examples to examine its performance in the two
dimensional problems. The numerical examples include flow past a
circular cylinder symmetrically installed in a Channel and flow past
two circular cylinders with different diameters. From the numerical
experiments, the ability of the solver to simulate flows with
complicated immersed boundaries is demonstrated and the nested grid
approach can efficiently speed up the numerical solutions.
Abstract: Following harvest, fresh produce needs to be cooled
immediately in a room where the air temperature and the relative air
humidity are controlled to maintain the produce quality. In this paper,
an experimental study for forced air cooling of fresh produce
(cauliflower) is performed using a pilot developed within our
laboratory. Furthermore, a numerical simulation of spherical
produces, taking into account the aerodynamic aspect and also the
heat transfer in the produce and in the air, was carried out using a
finite element method. At the end of this communication,
experimental results are presented and compared with the simulation.
Abstract: This paper examines the depiction of Muslim militants in Thai newspapers in 2004. Stuart Hall-s “representation" and “public idioms" are used as theoretical frameworks. Critical Discourse Analysis is employed as a methodology to examine 240 news articles from two leading Thai language newspapers. The results show that the militants are usually labeled as “southern bandits." This suggests that they are just a culprit of the violence in the deep south of Thailand. They are usually described as people who cause turbulence. Consequently, the military have to get rid of them. However, other aspects of the groups such as their political agenda or the failures of the Thai state in dealing with the Malay Muslims were not mention in the news stories. In the time of violence, the researcher argues that this kind of newspaper coverage may help perpetuate the discourse of Malay Muslim, instead of providing fuller picture of the ongoing conflicts.