Abstract: The changes in quality properties and nutritional
components in two fermented mugworts (Artemisia capillaries
Thumberg, Artemisiaeasiaticae Nakai) were characterized followed
by the rapid pattern analysis of volatile flavor compounds by Electric
Nose based on SAW(Surface Acoustic Wave) sensor in GC system.
There were remarkable decreases in the pH and small changes in the
total soluble solids after fermentation. The L (lightness) and b
(yellowness) values in Hunter's color system were shown to be
decreased, whilst the a (redness) value was increased by fermentation.
The HPLC analysis demonstrated that total amino acids were
increased in quantity and the essential amino acids were contained
higher in A. asiaticaeNakai than in A. capillaries Thumberg. While
the total polyphenol contents were not affected by fermentation, the
total sugar contents were dramatically decreased. Scopoletinwere
highly abundant in A. capillarisThumberg, however, it was not
detected in A. asiaticaeNakai. Volatile flavor compounds by Electric
Nose showed that the intensity of several peaks were increased much
and seven additional flavor peaks were newly produced after
fermentation. The flavor differences of two mugworts were clearly
distinguished from the image patterns of VaporPrintTM which indicate
that the fermentation enables the two mugworts to have subtle flavor
differences.
Abstract: A research effort to find the reality of the business of Japan-s software globalization of enterprise-level business software systems has found that while the number of Japan-made enterpriselevel software systems is comparable with those of the other G7 countries, the business is limited to the East and Southeast Asian markets. This indicates that this business has a problem in the European and USA markets. Based on the knowledge that the research has established, the research concludes that the communication problems arise from the lack of individualists' communication styles and foreign language skills in Japan's software globalization is compensated by similarities in certain Japanese cultural factors and Japan's cultural power in the East and Southeast Asian markets and that this business does not have this compensation factor in the European and American markets due to dissimilarities and no cultural power.
Abstract: The development of sustainable utilization water resources is crucial. The ecological environment and water resources systems form the foundation of the existence and development of the social economy. The urban ecological support system depends on these resources as well. This research studies the vulnerability, criticality, and risk of climate change on water supply and demand in the main administrative district of the Taijiang Area (Tainan City). Based on the two situations set in this paper and various factors (indexes), this research adopts two kinds of weights (equal and AHP) to conduct the calculation and establish the water supply and demand risk map for the target year 2039. According to the risk analysis result, which is based on equal weight, only one district belongs to a high-grade district (Grade 4). Based on the AHP weight, 16 districts belong to a high-grade or higher-grade district (Grades 4 and 5), and from among them, two districts belong to the highest grade (Grade 5). These results show that the risk level of water supply and demand in cities is higher than that in towns. The government generally gives more attention to the adjustment strategy in the “cities." However, it should also provide proper adjustment strategies for the “towns" to be able to cope with the risks of water supply and demand.
Abstract: There are very complex communication systems, as
the multifunction radar, MFAR (Multi-Function Array Radar), where
functions are integrated all together, and simultaneously are
performed the classic functions of tracking and surveillance, as all
the functions related to the communication, countermeasures, and
calibration. All these functions are divided into the tasks to execute.
The task scheduler is a key element of the radar, since it does the
planning and distribution of energy and time resources to be shared
and used by all tasks. This paper presents schedulers based on the use
of multiple queue. Several schedulers have been designed and
studied, and it has been made a comparative analysis of different
performed schedulers. The tests and experiments have been done by
means of system software simulation. Finally a suitable set of radar
characteristics has been selected to evaluate the behavior of the task
scheduler working.
Abstract: This work presents a novel means of extracting fixedlength parameters from voice signals, such that words can be recognized
in linear time. The power and the zero crossing rate are first
calculated segment by segment from a voice signal; by doing so, two
feature sequences are generated. We then construct an FIR system
across these two sequences. The parameters of this FIR system, used
as the input of a multilayer proceptron recognizer, can be derived by
recursive LSE (least-square estimation), implying that the complexity of overall process is linear to the signal size. In the second part of
this work, we introduce a weighting factor λ to emphasize recent
input; therefore, we can further recognize continuous speech signals.
Experiments employ the voice signals of numbers, from zero to nine, spoken in Mandarin Chinese. The proposed method is verified to
recognize voice signals efficiently and accurately.
Abstract: This paper presents a comparative study on two most
popular control strategies for Permanent Magnet Synchronous Motor
(PMSM) drives: field-oriented control (FOC) and direct torque
control (DTC). The comparison is based on various criteria including
basic control characteristics, dynamic performance, and
implementation complexity. The study is done by simulation using
the Simulink Power System Blockset that allows a complete
representation of the power section (inverter and PMSM) and the
control system. The simulation and evaluation of both control
strategies are performed using actual parameters of Permanent
Magnet Synchronous Motor fed by an IGBT PWM inverter.
Abstract: This paper describes various stages of design and prototyping of a modular robot for use in various industrial applications. The major goal of current research has been to design and make different robotic joints at low cost capable of being assembled together in any given order for achieving various robot configurations. Five different types of joins were designed and manufactured where extensive research has been carried out on the design of each joint in order to achieve optimal strength, size, modularity, and price. This paper presents various stages of research and development undertaken to engineer these joints that include material selection, manufacturing, and strength analysis. The outcome of this research addresses the birth of a new generation of modular industrial robots with a wider range of applications and greater efficiency.
Abstract: In this paper, we have examined the effect of process
parameter variation on the electrical characteristics of an LDMOS
device. The rate of change in the electrical parameters such as cut off
frequency, breakdown voltage and drain saturation current as a
function of the process parameters is investigated
Abstract: The service sector continues to grow and the percentage
of GDP accounted for by service industries keeps increasing. The
growth and importance of service to an economy is not just a
phenomenon of advanced economies, service is now a majority of the
world gross domestic products. However, the performance evaluation
process of new service development problems generally involves
uncertain and imprecise data. This paper presents a 2-tuple fuzzy
linguistic computing approach to dealing with heterogeneous
information and information loss problems while the processes of
subjective evaluation integration. The proposed method based on group
decision-making scenario to assist business managers in measuring
performance of new service development manipulates the
heterogeneity integration processes and avoids the information loss
effectively.
Abstract: Time delay in bilateral teleoperation system was
introduced as a sufficient reason to make the system unstable or
certainly degrade the system performance. In this paper, simulations
and experimental results of implementing p-like control scheme,
under different ranges of variable time delay, will be presented to
verify a certain criteria, which guarantee the system stability and
position tracking. The system consists of two Phantom premium 1.5A
devices. One of them acts as a master and the other acts as a slave.
The study includes deriving the Phantom kinematic and dynamic
model, establishing the link between the two Phantoms over
Simulink in Matlab, and verifying the stability criteria with
simulations and real experiments.
Abstract: Variable speed drives are growing and varying. Drives expanse depend on progress in different part of science like power system, microelectronic, control methods, and so on. Artificial intelligent contains hard computation and soft computation. Artificial intelligent has found high application in most nonlinear systems same as motors drive. Because it has intelligence like human but there are no sentimental against human like angriness and.... Artificial intelligent is used for various points like approximation, control, and monitoring. Because artificial intelligent techniques can use as controller for any system without requirement to system mathematical model, it has been used in electrical drive control. With this manner, efficiency and reliability of drives increase and volume, weight and cost of them decrease.
Abstract: The present work is concerned with sulfidation of Cu,
Zn and Ni containing plating wastewater with CaS. The sulfidation
experiments were carried out at a room temperature by adding solid
CaS to simulated metal solution containing either single-metal of Ni,
Zn and Cu, or Ni-Zn-Cu mixture. At first, the experiments were
conducted without pH adjustment and it was found that the complete
sulfidation of Zn and Ni was achieved at an equimolar ratio of CaS to a
particular metal. However, in the case of Cu, a complete copper
sulfidation was achieved at CaS to Cu molar ratio of about 2. In the
case of the selective sulfidation, a simulated plating solution
containing Cu, Zn and Ni at the concentration of 100 mg/dm3 was
treated with CaS under various pH conditions. As a result, selective
precipitation of metal sulfides was achieved by a sulfidation treatment
at different pH values. Further, the precipitation agents of NaOH,
Na2S and CaS were compared in terms of the average specific
filtration resistance and compressibility coefficients of metal sulfide
slurry. Consequently, based on the lowest filtration parameters of the
produced metal sulfides, it was concluded that CaS was the most
effective precipitation agent for separation and recovery of Cu, Zn and
Ni.
Abstract: Today, numerical simulation is a powerful tool to
solve various hydraulic engineering problems. The aim of this
research is numerical solutions of shallow water equations using
finite volume method for Simulations of dam break over wet and dry
bed. In order to solve Riemann problem, Roe-s approximate solver is
used. To evaluate numerical model, simulation was done in 1D and
2D states. In 1D state, two dam break test over dry bed (with and
without friction) were studied. The results showed that Structural
failure around the dam and damage to the downstream constructions
in bed without friction is more than friction bed. In 2D state, two
tests for wet and dry beds were done. Generally in wet bed case,
waves are propagated to canal sides but in dry bed it is not
significant. Therefore, damage to the storage facilities and
agricultural lands in wet bed case is more than in dry bed.
Abstract: The main purpose of this research was to analyze Socio-Cultural obstacles of disseminating of nanotechnology in Iran's agricultural section. One hundred twenty eight out of a total of 190 researchers with different levels of expertise in and familiarity with nanotechnology were randomly selected and questionnaires completed by them. Face validity have been done by expert's suggestion and correction, reliability by using Cronbakh-Alpha formula. The results of a factor analysis showed variation for different factors. For cultural factors 19/475 percent, for management 13/139 percent, information factor 11/277 percent, production factor 9/703 percent, social factor 9/267 percent, and for attitude factor it became 8/947 percent. Also results indicated that socio-cultural factors were the most important obstacle for nanotechnology dissemination in agricultural section in Iran.
Abstract: Brain ArterioVenous Malformation (BAVM) is an abnormal tangle of brain blood vessels where arteries shunt directly into veins with no intervening capillary bed which causes high pressure and hemorrhage risk. The success of treatment by embolization in interventional neuroradiology is highly dependent on the accuracy of the vessels visualization. In this paper the performance of clustering techniques on vessel segmentation from 3- D rotational angiography (3DRA) images is investigated and a new technique of segmentation is proposed. This method consists in: preprocessing step of image enhancement, then K-Means (KM), Fuzzy C-Means (FCM) and Expectation Maximization (EM) clustering are used to separate vessel pixels from background and artery pixels from vein pixels when possible. A post processing step of removing false-alarm components is applied before constructing a three-dimensional volume of the vessels. The proposed method was tested on six datasets along with a medical assessment of an expert. Obtained results showed encouraging segmentations.
Abstract: In this paper, we have combined some spatial derivatives with the optimised time derivative proposed by Tam and Webb in order to approximate the linear advection equation which is given by = 0. Ôêé Ôêé + Ôêé Ôêé x f t u These spatial derivatives are as follows: a standard 7-point 6 th -order central difference scheme (ST7), a standard 9-point 8 th -order central difference scheme (ST9) and optimised schemes designed by Tam and Webb, Lockard et al., Zingg et al., Zhuang and Chen, Bogey and Bailly. Thus, these seven different spatial derivatives have been coupled with the optimised time derivative to obtain seven different finite-difference schemes to approximate the linear advection equation. We have analysed the variation of the modified wavenumber and group velocity, both with respect to the exact wavenumber for each spatial derivative. The problems considered are the 1-D propagation of a Boxcar function, propagation of an initial disturbance consisting of a sine and Gaussian function and the propagation of a Gaussian profile. It is known that the choice of the cfl number affects the quality of results in terms of dissipation and dispersion characteristics. Based on the numerical experiments solved and numerical methods used to approximate the linear advection equation, it is observed in this work, that the quality of results is dependent on the choice of the cfl number, even for optimised numerical methods. The errors from the numerical results have been quantified into dispersion and dissipation using a technique devised by Takacs. Also, the quantity, Exponential Error for Low Dispersion and Low Dissipation, eeldld has been computed from the numerical results. Moreover, based on this work, it has been found that when the quantity, eeldld can be used as a measure of the total error. In particular, the total error is a minimum when the eeldld is a minimum.
Abstract: Stainless steel has been employed in many
engineering applications ranging from pharmaceutical equipment to
piping in the nuclear reactors and storage to chemical products. In
this attempt, simulation of fatigue crack growth based on
experimental results of austenitic stainless steel 304L was presented
using AFGROW code when NASGRO mode laws adopted. Double
through crack at hole specimen is used in this investigation under
constant amplitude loading. Effect of mean stress is highlighted.
Results show that fatigue crack growth rate (FCGR) and fatigue life
were affected by maximum applied load and dimension of hole. An
equivalent of Paris law for this material was estimated.
Abstract: The optimal control problem for the viscoelastic melt
spinning process has not been reported yet in the literature. In this
study, an optimal control problem for a mathematical model of a
viscoelastic melt spinning process is considered. Maxwell-Oldroyd
model is used to describe the rheology of the polymeric material, the
fiber is made of. The extrusion velocity of the polymer at the spinneret
as well as the velocity and the temperature of the quench air and the
fiber length serve as control variables. A constrained optimization
problem is derived and the first–order optimality system is set up
to obtain the adjoint equations. Numerical solutions are carried out
using a steepest descent algorithm. A computer program in MATLAB
is developed for simulations.
Abstract: Access control is a critical security service in Wire- less
Sensor Networks (WSNs). To prevent malicious nodes from joining
the sensor network, access control is required. On one hand, WSN
must be able to authorize and grant users the right to access to the
network. On the other hand, WSN must organize data collected by
sensors in such a way that an unauthorized entity (the adversary)
cannot make arbitrary queries. This restricts the network access only
to eligible users and sensor nodes, while queries from outsiders will
not be answered or forwarded by nodes. In this paper we presentee
different access control schemes so as to ?nd out their objectives,
provision, communication complexity, limits, etc. Using the node
density parameter, we also provide a comparison of these proposed
access control algorithms based on the network topology which can
be flat or hierarchical.
Abstract: To identify an endothelial cell-specific promoter suitable for vascular-specific targeting, we tested five promoters in vitro--Tie2SE, Tie2LE, ICAM2, Flt-1 and vWF--for promoter activity and specificity in endothelial cells, smooth muscle cells and non-vascular resident cells as well as tissues. These promoters, except for vWF, exhibited good endothelial activity and specificity in vitro. In a syngenic heart transplantation model, the ICAM2 promoter was variably functional in coronary endothelial cells of donor hearts. Thus, the ICAM2, Flt-1, Tie2SE and Tie2LE promoters hold promise for endothelial-specific targeting, but in vitro expression may not predict in vivo expression.