Abstract: A generalized unified power quality conditioner
(GUPQC) by using three single-phase three-level voltage source
converters (VSCs) connected back-to-back through a common dc
link is proposed in this paper as a new custom power device for a
three-feeder distribution system. One of the converters is connected
in shunt with one feeder for mitigation of current harmonics and
reactive power compensation, while the other two VSCs are
connected in series with the other two feeders to maintain the load
voltage sinusoidal and at constant level. A new control scheme based
on synchronous reference frame is proposed for series converters.
The simulation analysis on compensation performance of GUPQC
based on PSCAD/EMTDC is reported.
Abstract: Kuwait-s electric power system is vertically integrated
organization owned and operated by the government. For more than
five decades, the government of Kuwait has provided relatively
reliable electric services to consumers with subsidized electric
service fees. Given the country-s rapid socio-economical
development and consequently the increase of electricity demand, a
question that inflicts itself: Is it necessary to reform the power system
to face the fast growing demand? This paper recommends that the
government should consider the private sector as a partner in
operating the power system. Therefore, power system restructuring is
needed to allow such partnership. There are challenges that prevent
such restructuring. Abstract recommendations toward resolving these
challenges are proposed.
Abstract: In this paper, we propose a novel metal oxide
semiconductor field effect transistor with L-shaped channel structure
(LMOS), and several type of L-shaped structures are also designed,
studied and compared with the conventional MOSFET device for the
same average gate length (Lavg). The proposed device electrical
characteristics are analyzed and evaluated by three dimension (3-D)
ISE-TCAD simulator. It can be confirmed that the LMOS devices
have higher on-state drain current and both lower drain-induced
barrier lowering (DIBL) and subthreshold swing (S.S.) than its
conventional counterpart has. In addition, the transconductance and
voltage gain properties of the LMOS are also improved.
Abstract: The purpose of this paper is to highlight the
importance of the concept of competitiveness in the supply chain and
to present a conceptual framework for Supply Chain Competitiveness
(SCC). The framework is based on supply chain activities, which are
inputs, necessary for SCC and the benefits which are the outputs of
SCC. A literature review is conducted on key supply chain
competitiveness issues, its determinants, its various dimensions
followed by exploration for SCC. Based on the insights gained, a
conceptual framework for SCC is presented based on activities for
SCC, SCC environment and outcomes of SCC. The information flow
in the conceptual framework is bi-directional at all levels and the
activities are interrelated in a global competitive environment. The
activities include the activities of suppliers, manufacturers and
distributors, giving more emphasis on manufacturers- activities.
Further, implications of various factors such as economic, politicolegal,
technical, socio-cultural, competition, demographic etc. are
also highlighted. The SCC framework is an attempt to cover the
relatively less explored area of supply chain competitiveness. It is
expected that this work will further motivate researchers,
academicians and practitioners to work in this area and offers
conceptual help in providing a directions for supply chain
competitiveness which leads to improvement in the supply chain and
supply chain performance.
Abstract: This paper analyzes the patterns of the Monte Carlo
data for a large number of variables and minterms, in order to
characterize the circuit path length behavior. We propose models
that are determined by training process of shortest path length
derived from a wide range of binary decision diagram (BDD)
simulations. The creation of the model was done use of feed forward
neural network (NN) modeling methodology. Experimental results
for ISCAS benchmark circuits show an RMS error of 0.102 for the
shortest path length complexity estimation predicted by the NN
model (NNM). Use of such a model can help reduce the time
complexity of very large scale integrated (VLSI) circuitries and
related computer-aided design (CAD) tools that use BDDs.
Abstract: The use of polypropylene mesh devices for Pelvic
Organ Prolapse (POP) spread rapidly during the last decade, yet our
knowledge of the mesh-tissue interaction is far from complete. We
aimed to perform a thorough pathological examination of explanted
POP meshes and describe findings that may explain mechanisms of
complications resulting in product excision. We report a spectrum of
important findings, including nerve ingrowth, mesh deformation,
involvement of detrusor muscle with neural ganglia, and
polypropylene degradation. Analysis of these findings may improve
and guide future treatment strategies.
Abstract: Study was conducted to determine the concentration of
copper, cadmium, lead and zinc in Cabomba furcata that found
abundance in Lake Chini. This aquatic plant was collected randomly
within the lake for heavy metal determination. Water quality
measurement was undertaken in situ for temperature, pH,
conductivity and dissolved oksigen using portable multi sensor probe
YSI model 556. The C. furcata was digested using wet digestion
method and heavy metal concentrations were analysed using Atomic
Absorption Spectrometer (AAS) Perkin Elmer 4100B (flame
method). Result of water quality classify Lake Chini between class II
to class III using Malaysian Water Quality Standard. According to
this standard, Lake Chini has moderate quality, which normal for
natural lake. Heavy metal concentrations in C.furcata were low and
found to be lower than the critical toxic value in aquatic plants. Oneway
ANOVA test indicated the heavy metal concentrations in
C.furcata were significantly differ between sampling location. Water
quality and heavy metal concentrations indicates that Lake Chini was
not receives anthropogenic load from nearby activities.
Abstract: Attitude Determination (AD) of a spacecraft using the
phase measurements of the Global Navigation Satellite System
(GNSS) is an active area of research. Various attitude determination
algorithms have been developed in yester years for spacecrafts using
different sensors but the last two decades have witnessed a
phenomenal increase in research related with GPS receivers as a
stand-alone sensor for determining the attitude of satellite using the
phase measurements of the signals from GNSS. The GNSS-based
Attitude determination algorithms have been experimented in many
real missions. The problem of AD algorithms using GNSS phase
measurements has two important parts; the ambiguity resolution and
the determining of attitude. Ambiguity resolution is the widely
addressed topic in literature for implementing the AD algorithm
using GNSS phase measurements for achieving the accuracy of
millimeter level. This paper broadly overviews the different
techniques for resolving the integer ambiguities encountered in AD
using GNSS phase measurements.
Abstract: This paper is intended to assist anyone with some general technical experience, but perhaps limited specific knowledge of heat transfer equipment. A characteristic of heat exchanger design is the procedure of specifying a design, heat transfer area and pressure drops and checking whether the assumed design satisfies all requirements or not. The purpose of this paper is how to design the oil cooler (heat exchanger) especially for shell-and-tube heat exchanger which is the majority type of liquid-to-liquid heat exchanger. General design considerations and design procedure are also illustrated in this paper and a flow diagram is provided as an aid of design procedure. In design calculation, the MatLAB and AutoCAD software are used. Fundamental heat transfer concepts and complex relationships involved in such exchanger are also presented in this paper. The primary aim of this design is to obtain a high heat transfer rate without exceeding the allowable pressure drop. This computer program is highly useful to design the shell-and-tube type heat exchanger and to modify existing deign.
Abstract: In this paper, we propose a fully-utilized, block-based 2D DWT (discrete wavelet transform) architecture, which consists of four 1D DWT filters with two-channel QMF lattice structure. The proposed architecture requires about 2MN-3N registers to save the intermediate results for higher level decomposition, where M and N stand for the filter length and the row width of the image respectively. Furthermore, the proposed 2D DWT processes in horizontal and vertical directions simultaneously without an idle period, so that it computes the DWT for an N×N image in a period of N2(1-2-2J)/3. Compared to the existing approaches, the proposed architecture shows 100% of hardware utilization and high throughput rates. To mitigate the long critical path delay due to the cascaded lattices, we can apply the pipeline technique with four stages, while retaining 100% of hardware utilization. The proposed architecture can be applied in real-time video signal processing.
Abstract: For higher order multiplications, a huge number of
adders or compressors are to be used to perform the partial product
addition. We have reduced the number of adders by introducing
special kind of adders that are capable to add five/six/seven bits per
decade. These adders are called compressors. Binary counter
property has been merged with the compressor property to develop
high order compressors. Uses of these compressors permit the
reduction of the vertical critical paths. A 16×16 bit multiplier has
been developed using these compressors. These compressors make
the multipliers faster as compared to the conventional design that
have been used 4-2 compressors and 3-2 compressors.
Abstract: One way for optimum loading of overdimensioning
conveyers is speed (capacity) decrement, with attention for
production capabilities and demands. At conveyers which drives with
three phase slip-ring induction motor, technically reasonable solution
for conveyer (driving motors) speed regulation is using constant
torque subsynchronous cascade with static semiconductor converter
and transformer for energy reversion to the power network. In the
paper is described mathematical model for parameter calculation of
two-motors 6 kV subsynchronous cascade. It is also demonstrated
that applying of this cascade gave several good properties, foremost
in electrical energy saving, also in improving of other energy
indexes, and finally that results in cost reduction of complete
electrical motor drive.
Abstract: Snoring is prevalent and is the most significant feature
of sleep-disordered breathing (SDB). Ignore the therapies of SDB will
lead to serious problems in health. Based on the research of
mechanisms, diagnosis, and treatments of snoring, oral appliances are
ensured in therapeutic effect and compliance, especially the
mandibular advancement devices (MADs). Market survey includes
commercial product reviews and patent analyses. Due to pay more
attention to the sleep medicine, the oral appliances are considered as a
standard treatment of snoring that promoted by American Academy of
Sleep Medicine (AASM). There are more and more adjustable MADs
developed since 1995. According to the patent analyses, there are
many drawbacks existed in the present design, such as uncomfortable,
high cost, bulky volume, and complex adjustment. In this study,
several new designs of the MAD are proposed.
Abstract: A challenging problem in radar signal processing is to
achieve reliable target detection in the presence of interferences. In
this paper, we propose a novel algorithm for automatic censoring of
radar interfering targets in log-normal clutter. The proposed
algorithm, termed the forward automatic censored cell averaging
detector (F-ACCAD), consists of two steps: removing the corrupted
reference cells (censoring) and the actual detection. Both steps are
performed dynamically by using a suitable set of ranked cells to
estimate the unknown background level and set the adaptive
thresholds accordingly. The F-ACCAD algorithm does not require
any prior information about the clutter parameters nor does it require
the number of interfering targets. The effectiveness of the F-ACCAD
algorithm is assessed by computing, using Monte Carlo simulations,
the probability of censoring and the probability of detection in
different background environments.
Abstract: The paper outlines the relevance of computational
geometry within the design and production process of architecture.
Based on two case studies, the digital chain - from the initial formfinding
to the final realization of spatial concepts - is discussed in
relation to geometric principles. The association with the fascinating
complexity that can be found in nature and its underlying geometry
was the starting point for both projects presented in the paper. The
translation of abstract geometric principles into a three-dimensional
digital design model – realized in Rhinoceros – was followed by a
process of transformation and optimization of the initial shape that
integrated aesthetic, spatial and structural qualities as well as aspects
of material properties and conditions of production.
Abstract: In this paper, we present the design and experimental
evaluation of complementary energy path adiabatic logic (CEPAL)
based 1 bit full adder circuit. A simulative investigation on the
proposed full adder has been done using VIRTUOSO SPECTRE
simulator of cadence in 0.18μm UMC technology and its
performance has been compared with the conventional CMOS full
adder circuit. The CEPAL based full adder circuit exhibits the energy
saving of 70% to the conventional CMOS full adder circuit, at 100
MHz frequency and 1.8V operating voltage.
Abstract: There have been widespread applications of fluidized beds in industries which are related to the combination of gas-solid particles during the last decade. For instance, in order to crack the catalyses in petrochemical industries or as a drier in food industries. High capacity of fluidized bed in heat and mass transfer has made this device very popular. In order to achieve a higher efficiency of fluidized beds, a particular attention has been paid to beds with pulsating air flow. In this paper, a fluidized bed device with pulsating flow has been designed and constructed. Size of particles have been used during the test are in the range of 40 to 100μm. The purpose of this experimental test is to investigate the air flow regime, observe the particles- movement and measure the pressure loss along the bed. The effects of pulsation can be evaluated by comparing the results for both continuous and pulsating flow. Results of both situations are compared for various gas speeds. Moreover the above experiment is numerically simulated by using Fluent software and its numerical results are compared with the experimental results.
Abstract: Banishing hunger from the face of earth has been
frequently expressed in various international, national and regional
level conferences since 1974. Providing food security has become
important issue across the world particularly in developing countries.
In a developing country like India, where growth rate of population is
more than that of the food grains production, food security is a
question of great concern. According to the International Food Policy
Research Institute's Global Hunger Index, 2011, India ranks 67 of the
81 countries of the world with the worst food security status. After
Green Revolution, India became a food surplus country. Its
production has increased from 74.23 million tonnes in 1966-67 to
257.44 million tonnes in 2011-12. But after achieving selfsufficiency
in food during last three decades, the country is now
facing new challenges due to increasing population, climate change,
stagnation in farm productivity. Therefore, the main objective of the
present paper is to examine the food security situation at national
level in the country and further to explain the paradox of food
insecurity in a food surplus state of India i.e in Punjab at micro level.
In order to achieve the said objectives, secondary data collected from
the Ministry of Agriculture and the Agriculture department of Punjab
State was analyzed. The result of the study showed that despite
having surplus food production the country is still facing food
insecurity problem at micro level. Within the Kandi belt of Punjab
state, the area adjacent to plains is food secure while the area along
the hills falls in food insecure zone.
The present paper is divided into following three sections (i)
Introduction, (ii) Analysis of food security situation at national level
as well as micro level (Kandi belt of Punjab State) (iii) Concluding
Observations
Abstract: Despite so many years- development, the mainstream of workflow solutions from IT industries has not made ad-hoc workflow-support easy or inexpensive in MIS. Moreover, most of academic approaches tend to make their resulted BPM (Business Process Management) more complex and clumsy since they used to necessitate modeling workflow. To cope well with various ad-hoc or casual requirements on workflows while still keeping things simple and inexpensive, the author puts forth first the TSM design pattern that can provide a flexible workflow control while minimizing demand of predefinitions and modeling workflow, which introduces a generic approach for building BPM in workflow-aware MISs (Management Information Systems) with low development and running expenses.
Abstract: Twist drills are geometrical complex tools and thus various researchers have adopted different mathematical and experimental approaches for their simulation. The present paper acknowledges the increasing use of modern CAD systems and using the API (Application Programming Interface) of a CAD system, drilling simulations are carried out. The developed DRILL3D software routine, creates parametrically controlled tool geometries and using different cutting conditions, achieves the generation of solid models for all the relevant data involved (drilling tool, cut workpiece, undeformed chip). The final data derived, consist a platform for further direct simulations regarding the determination of cutting forces, tool wear, drilling optimizations etc.