Abstract: Properly sized capacitor banks are connected across induction motors for several reasons including power factor correction, reducing distortions, increasing capacity, etc. Total harmonic distortion (THD) and power factor (PF) are used in such cases to quantify the improvements obtained through connection of the external capacitor banks. On the other hand, one of the methods for assessing the motor internal condition is by the use of Park-s pattern analysis. In spite of taking adequate precautionary measures, the capacitor banks may sometimes malfunction. Such a minor fault in the capacitor bank is often not apparently discernible. This may however, give rise to substantial degradation of power factor correction performance and may also damage the supply profile. The case is more severe with the fact that the Park-s pattern gets distorted due to such external capacitor faults, and can give anomalous results about motor internal fault analyses. The aim of this paper is to present simulation and hardware laboratory test results to have an understanding of the anomalies in harmonic distortion and Park-s pattern analyses in induction motors due to capacitor bank defects.
Abstract: In this paper, we analyze the problem of quasiballistic electron transport in ultra small of mercury -cadmiumtelluride (Hg0.8Cd0.2Te -MCT) n+-n- n+ devices from hydrodynamic point view. From our study, we note that, when the size of the active layer is low than 0.1μm and for low bias application( ( ≥ 9mV), the quasi-ballistic transport has an important effect.
Abstract: It is claimed that a new style of urban planning and
policy intertwined with ICT is emerging and urban planning and ICT
policy are no longer considered as separate disciplines. The
interactions between electronic spaces and urban spaces are so
complex and uncertain that confront urban planners and policy makers
with great challenges. However, the assumption about the relationship
between ICT and urban planning is mainly based on North American
and European experiences. In the light of empirical evidence from
Taipei City, this paper shows that this new type of urban planning and
policy intertwined with ICT has existed in Asian city for a decade as
well. Based on these results, this paper further reviews how the Taipei
City government implements this new type of urban ICT planning and
the validity and realism of its underlying assumptions. Finally, it also
explores the extent to which urban ICT planning could promote
positive synergies between physical and electronic developments.
Abstract: The seismic vulnerability of an urban area is of a great
deal for local authorities especially those facing earthquakes. So, it is
important to have an efficient tool to assess the vulnerability of
existing buildings. The use of the VIP (Vulnerability Index Program)
and the GIS (Geographic Information System) let us to identify the
most vulnerable districts of an urban area.
The use of the vulnerability index method lets us to assess the
vulnerability of the center town of Blida (Algeria) which is a
historical town and which has grown enormously during the last
decades. In this method, three levels of vulnerability are defined. The
GIS has been used to build a data base in order to perform different
thematic analyses. These analyses show the seismic vulnerability of
Blida.
Abstract: This paper presents a new high speed simulation methodology to solve the long simulation time problem of CMOS image sensor matrix. Generally, for integrating the pixel matrix in SOC and simulating the system performance, designers try to model the pixel in various modeling languages such as VHDL-AMS, SystemC or Matlab. We introduce a new alternative method based on spice model in cadence design platform to achieve accuracy and reduce simulation time. The simulation results indicate that the pixel output voltage maximum error is at 0.7812% and time consumption reduces from 2.2 days to 13 minutes achieving about 240X speed-up for the 256x256 pixel matrix.
Abstract: The paper shows the necessity to increase the security
level for paper management in the cadastral field by using specific
graphical watermarks. Using the graphical watermarking will
increase the security in the cadastral content management;
furthermore any altered document will be validated afterwards of its
originality by checking the graphic watermark. If, by any reasons the
document is changed for counterfeiting, it is invalidated and found
that is an illegal copy due to the graphic check of the watermarking,
check made at pixel level
Abstract: Business and IT alignment has continued as a
top concern for business and IT executives for almost three
decades. Many researchers have conducted empirical studies on
the relationship between business-IT alignment and performance.
Yet, these approaches, lacking a social perspective, have had little
impact on sustaining performance and competitive advantage. In
addition to the limited alignment literature that explores
organisational learning that is represented in shared understanding,
communication, cognitive maps and experiences.
Hence, this paper proposes an integrated process that enables
social and intellectual dimensions through the concept of
organisational learning. In particular, the feedback and feedforward
process which provide a value creation across dynamic
multilevel of learning. This mechanism enables on-going
effectiveness through development of individuals, groups and
organisations, which improves the quality of business and IT
strategies and drives to performance.
Abstract: This paper demonstrates how the soft systems
methodology can be used to improve the delivery of a module in data warehousing for fourth year information technology students.
Graduates in information technology needs to have academic skills
but also needs to have good practical skills to meet the skills requirements of the information technology industry. In developing
and improving current data warehousing education modules one has to find a balance in meeting the expectations of various role players such as the students themselves, industry and academia. The soft
systems methodology, developed by Peter Checkland, provides a
methodology for facilitating problem understanding from different world views. In this paper it is demonstrated how the soft systems methodology can be used to plan the improvement of data
warehousing education for fourth year information technology students.
Abstract: Large volumes of fingerprints are collected and stored
every day in a wide range of applications, including forensics, access
control etc. It is evident from the database of Federal Bureau of
Investigation (FBI) which contains more than 70 million finger
prints. Compression of this database is very important because of this
high Volume. The performance of existing image coding standards
generally degrades at low bit-rates because of the underlying block
based Discrete Cosine Transform (DCT) scheme. Over the past
decade, the success of wavelets in solving many different problems
has contributed to its unprecedented popularity. Due to
implementation constraints scalar wavelets do not posses all the
properties which are needed for better performance in compression.
New class of wavelets called 'Multiwavelets' which posses more
than one scaling filters overcomes this problem. The objective of this
paper is to develop an efficient compression scheme and to obtain
better quality and higher compression ratio through multiwavelet
transform and embedded coding of multiwavelet coefficients through
Set Partitioning In Hierarchical Trees algorithm (SPIHT) algorithm.
A comparison of the best known multiwavelets is made to the best
known scalar wavelets. Both quantitative and qualitative measures of
performance are examined for Fingerprints.
Abstract: To understand complex living system an effort has
made by mechanical engineers and dentists to deliver prompt
products and services to patients concerned about their aesthetic look.
Since two decades various bracket systems have designed involving
techniques like milling, injection molding which are technically not
flexible for the customized dental product development. The aim of
this paper to design, develop a customized system which is
economical and mainly emphasizes the expertise design and
integration of engineering and dental fields. A custom made selfadjustable
lingual bracket and customized implants are designed and
developed using computer aided design (CAD) and rapid prototyping
technology (RPT) to improve the smiles and to overcome the
difficulties associated with conventional ones. Lengthy orthodontic
treatment usually not accepted by the patients because the patient
compliance is lost. Patient-s compliance can be improved by
facilitating faster tooth movements by designing a localized dental
vibrator using advanced engineering principles.
Abstract: In recent years, sustainable supply chain management
(SSCM) has been widely researched in academic domain. However,
due to the traditional operational role and the complexity of supply
chain management in the cement industry, a relatively small amount
of research has been conducted on cement supply chain simulation
integrated with sustainability criteria. This paper analyses the cement
supply chain operations using the Push-Pull supply chain
frameworks, the Life Cycle Assessment (LCA) methodology; and
proposal integration approach, proposes three supply chain scenarios
based on Make-To-Stock (MTS), Pack-To-Order (PTO) and Grind-
To-Order (GTO) strategies. A Discrete-Event Simulation (DES)
model of SSCM is constructed using Arena software to implement
the three-target scenarios. We conclude with the simulation results
that (GTO) is the optimal supply chain strategy that demonstrates the
best economic, ecological and social performance in the cement
industry.
Abstract: A long-term campaign for monitoring the
concentration of atmospheric Particulate Matter (PM) was conducted
at multiple sites located in the center and suburbs of the Tokyo
Metropolitan Area in Japan. The concentration of fine PM has shown a
declining trend over the last two decades. A positive matrix
factorization model elucidated that the contribution of combustion
sources was drastically reduced. In Japan, the regulations on vehicle
exhaust emissions were phased in and gradually tightened over the last
two decades, which has triggered a notable reduction in PM emissions
from automobiles and has contributed to the mitigation of the problem
of fine PM pollution.
Abstract: In this paper, a novel and fast algorithm for segmental
and subsegmental lung vessel segmentation is introduced using
Computed Tomography Angiography images. This process is quite
important especially at the detection of pulmonary embolism, lung
nodule, and interstitial lung disease. The applied method has been
realized at five steps. At the first step, lung segmentation is achieved.
At the second one, images are threshold and differences between the
images are detected. At the third one, left and right lungs are gathered
with the differences which are attained in the second step and Exact
Lung Image (ELI) is achieved. At the fourth one, image, which is
threshold for vessel, is gathered with the ELI. Lastly, identifying and
segmentation of segmental and subsegmental lung vessel have been
carried out thanks to image which is obtained in the fourth step. The
performance of the applied method is found quite well for
radiologists and it gives enough results to the surgeries medically.
Abstract: Segmentation is an important step in medical image
analysis and classification for radiological evaluation or computer
aided diagnosis. This paper presents the problem of inaccurate lung
segmentation as observed in algorithms presented by researchers
working in the area of medical image analysis. The different lung
segmentation techniques have been tested using the dataset of 19
patients consisting of a total of 917 images. We obtained datasets of
11 patients from Ackron University, USA and of 8 patients from
AGA Khan Medical University, Pakistan. After testing the algorithms
against datasets, the deficiencies of each algorithm have been
highlighted.
Abstract: Plants are commonly known for its positive
correlation in reducing temperature. Since it can benefit buildings by
modifying the microclimate, it-s also believed capable of reducing
the internal temperature. Various experiments have been done in
Universiti Sains Malaysia, Penang to investigate the comparison in
thermal benefits between two rooms, one being a typical control
room (exposed wall) and the other a biofacade room (plant shaded
wall). The investigations were conducted during non-rainy season for
approximately a month. Climbing plant Psophocarpus
tetrogonobulus from legume species was selected as insulation for
the biofacade wall. Conclusions were made on whether the biofacade
can be used to tackle the energy efficiency, based on the parameters
taken into consideration.
Abstract: Nuclear energy sources have been widely used in the
past decades in order to power spacecraft subsystems. Nevertheless,
their use has attracted controversy because of the risk of harmful
material released into the atmosphere if an accident were to occur
during the launch phase of the mission, leading to the general
adoption of photovoltaic systems.
As compared to solar cells, wind turbines have a great advantage
on Mars, as they can continuously produce power both during dust
storms and at night-time: this paper focuses on the potential of a wind
energy conversion system (WECS) considering the atmospheric
conditions on Mars. Wind potential on Martian surface has been
estimated, as well as the average energy requirements of a Martian
probe or surface rover. Finally, the expected daily energy output of
the WECS has been computed on the basis of both the swept area of
the rotor and the equivalent wind speed at the landing site.
Abstract: Innovations in technology have created new ethical
challenges. Essential use of electronic communication in the
workplace has escalated at an astronomical rate over the past decade.
As such, legal and ethical dilemmas confronted by both the employer
and the employee concerning managerial control and ownership of einformation
have increased dramatically in the USA. From the
employer-s perspective, ownership and control of all information
created for the workplace is an undeniable source of economic
advantage and must be monitored zealously. From the perspective of
the employee, individual rights, such as privacy, freedom of speech,
and freedom from unreasonable search and seizure, continue to be
stalwart legal guarantees that employers are not legally or ethically
entitled to abridge in the workplace. These issues have been the
source of great debate and the catalyst for legal reform. The fine line
between ethical and legal has been complicated by emerging
technologies. This manuscript will identify and discuss a number of
specific legal and ethical issues raised by the dynamic electronic
workplace and conclude with suggestions that employers should
follow to respect the delicate balance between employees- legal
rights to privacy and the employer's right to protect its knowledge
systems and infrastructure.
Abstract: Artificial Immune System is adopted as a Heuristic
Algorithm to solve the combinatorial problems for decades.
Nevertheless, many of these applications took advantage of the benefit
for applications but seldom proposed approaches for enhancing the
efficiency. In this paper, we continue the previous research to develop
a Self-evolving Artificial Immune System II via coordinating the T
and B cell in Immune System and built a block-based artificial
chromosome for speeding up the computation time and better
performance for different complexities of problems. Through the
design of Plasma cell and clonal selection which are relative the
function of the Immune Response. The Immune Response will help
the AIS have the global and local searching ability and preventing
trapped in local optima. From the experimental result, the significant
performance validates the SEAIS II is effective when solving the
permutation flows-hop problems.
Abstract: In Image processing the Image compression can improve
the performance of the digital systems by reducing the cost and
time in image storage and transmission without significant reduction
of the Image quality. This paper describes hardware architecture of
low complexity Discrete Cosine Transform (DCT) architecture for
image compression[6]. In this DCT architecture, common computations
are identified and shared to remove redundant computations
in DCT matrix operation. Vector processing is a method used for
implementation of DCT. This reduction in computational complexity
of 2D DCT reduces power consumption. The 2D DCT is performed
on 8x8 matrix using two 1-Dimensional Discrete cosine transform
blocks and a transposition memory [7]. Inverse discrete cosine
transform (IDCT) is performed to obtain the image matrix and
reconstruct the original image. The proposed image compression
algorithm is comprehended using MATLAB code. The VLSI design
of the architecture is implemented Using Verilog HDL. The proposed
hardware architecture for image compression employing DCT was
synthesized using RTL complier and it was mapped using 180nm
standard cells. . The Simulation is done using Modelsim. The
simulation results from MATLAB and Verilog HDL are compared.
Detailed analysis for power and area was done using RTL compiler
from CADENCE. Power consumption of DCT core is reduced to
1.027mW with minimum area[1].
Abstract: The proposed multiplexer-based novel 1-bit full
adder cell is schematized by using DSCH2 and its layout is generated
by using microwind VLSI CAD tool. The adder cell layout
interconnect analysis is performed by using BSIM4 layout analyzer.
The adder circuit is compared with other six existing adder circuits
for parametric analysis. The proposed adder cell gives better
performance than the other existing six adder circuits in terms of
power, propagation delay and PDP. The proposed adder circuit is
further analyzed for interconnect analysis, which gives better
performance than other adder circuits in terms of layout thickness,
width and height.