Abstract: A Laboratory-scale packed bed reactor with microbial
cellulose as the biofilm carrier was used to investigate the
denitrification of high-strength nitrate wastewater with specific
emphasis on the effect the nitrogen loading rate and hydraulic
retention time. Ethanol was added as a carbon source for
denitrification. As a result of this investigation, it was found that up
to 500 mg/l feed nitrate concentration the present system is able to
produce an effluent with nitrate content below 10 ppm at 3 h
hydraulic retention time. The highest observed denitrification rate
was 4.57 kg NO3-N/ (m3 .d) at a nitrate load of 5.64 kg NO3-
N/(m3 .d), and removal efficiencies higher than 90% were obtained
for loads up to 4.2 kg NO3-N/(m3 .d). A mass relation between COD
consumed and NO3-N removed around 2.82 was observed. This
continuous-flow bioreactor proved an efficient denitrification system
with a relatively low retention time.
Abstract: The objective of this manuscript is to find area under the plasma concentration- time curve (AUC) for multiple doses of salbutamol sulphate sustained release tablets (Ventolin® oral tablets SR 8 mg, GSK, Pakistan) in the group of 18 healthy adults by using computational mathematics techniques. Following the administration of 4 doses of Ventolin® tablets 12 hourly to 24 healthy human subjects and bioanalysis of obtained plasma samples, plasma drug concentration-time profile was constructed. AUC, an important pharmacokinetic parameter, was measured using integrated equation of multiple oral dose regimens. The approximated AUC was also calculated by using computational mathematics techniques such as repeated rectangular, repeated trapezium and repeated Simpson's rule and compared with exact value of AUC calculated by using integrated equation of multiple oral dose regimens to find best computational mathematics method that gives AUC values closest to exact. The exact values of AUC for four consecutive doses of Ventolin® oral tablets were 150.5819473, 157.8131756, 164.4178231 and 162.78 ng.h/ml while the closest values approximated AUC values were 149.245962, 157.336171, 164.2585768 and 162.289224 ng.h/ml, respectively as found by repeated rectangular rule. The errors in the approximated values of AUC were negligible. It is concluded that all computational tools approximated values of AUC accurately but the repeated rectangular rule gives slightly better approximated values of AUC as compared to repeated trapezium and repeated Simpson's rules.
Abstract: In recent years, Radio Frequency Identification (RFID)
is followed with interest by many researches, especially for the
purpose of indoor positioning as the innate properties of RFID are
profitable for achieving it. A lot of algorithms or schemes are proposed
to be used in the RFID-based positioning system, but most of them are
lack of environmental consideration and it induces inaccuracy of
application. In this research, a lot of algorithms and schemes of RFID
indoor positioning are discussed to see whether effective or not on
application, and some rules are summarized for achieving accurate
positioning. On the other hand, a new term “Noise Factor" is involved
to describe the signal loss between the target and the obstacle. As a
result, experimental data can be obtained but not only simulation; and
the performance of the positioning system can be expressed
substantially.
Abstract: One of the major disadvantages of the minimally
invasive surgery (MIS) is the lack of tactile feedback to the surgeon.
In order to identify and avoid any damage to the grasped complex
tissue by endoscopic graspers, it is important to measure the local
softness of tissue during MIS. One way to display the measured
softness to the surgeon is a graphical method. In this paper, a new
tactile sensor has been reported. The tactile sensor consists of an
array of four softness sensors, which are integrated into the jaws of a
modified commercial endoscopic grasper. Each individual softness
sensor consists of two piezoelectric polymer Polyvinylidene Fluoride
(PVDF) films, which are positioned below a rigid and a compliant
cylinder. The compliant cylinder is fabricated using a micro molding
technique. The combination of output voltages from PVDF films is
used to determine the softness of the grasped object. The theoretical
analysis of the sensor is also presented.
A method has been developed with the aim of reproducing the
tactile softness to the surgeon by using a graphical method. In this
approach, the proposed system, including the interfacing and the data
acquisition card, receives signals from the array of softness sensors.
After the signals are processed, the tactile information is displayed
by means of a color coding method. It is shown that the degrees of
softness of the grasped objects/tissues can be visually differentiated
and displayed on a monitor.
Abstract: The LMS adaptive filter has several parameters which can affect their performance. From among these parameters, most papers handle the step size parameter for controlling the performance. In this paper, we approach three parameters: step-size, filter tap-size and filter form. The regression analysis is used for defining the relation between parameters and performance of LMS adaptive filter with using the system level simulation results. The results present that all parameters have performance trends in each own particular form, which can be estimated from equations drawn by regression analysis.
Abstract: In this paper, a new method of controlling position of AC Servomotor using Field Programmable Gate Array (FPGA). FPGA controller is used to generate direction and the number of pulses required to rotate for a given angle. Pulses are sent as a square wave, the number of pulses determines the angle of rotation and frequency of square wave determines the speed of rotation. The proposed control scheme has been realized using XILINX FPGA SPARTAN XC3S400 and tested using MUMA012PIS model Alternating Current (AC) servomotor. Experimental results show that the position of the AC Servo motor can be controlled effectively. KeywordsAlternating Current (AC), Field Programmable Gate Array (FPGA), Liquid Crystal Display (LCD).
Abstract: Road traffic accidents are a major cause of death worldwide. In an attempt to reduce accidents, some research efforts have focused on creating Advanced Driver Assistance Systems (ADAS) able to detect vehicle, driver and environmental conditions and to use this information to identify cues for potential accidents. This paper presents continued work on a novel Non-intrusive Intelligent Driver Assistance and Safety System (Ni-DASS) for assessing driver point of regard within vehicles. It uses an on-board CCD camera to observe the driver-s face. A template matching approach is used to compare the driver-s eye-gaze pattern with a set of eye-gesture templates of the driver looking at different focal points within the vehicle. The windscreen is divided into cells and comparison of the driver-s eye-gaze pattern with templates of a driver-s eyes looking at each cell is used to determine the driver-s point of regard on the windscreen. Results indicate that the proposed technique could be useful in situations where low resolution estimates of driver point of regard are adequate. For instance, To allow ADAS systems to alert the driver if he/she has positively failed to observe a hazard.
Abstract: Assembly line balancing is a very important issue in
mass production systems due to production cost. Although many
studies have been done on this topic, but because assembly line
balancing problems are so complex they are categorized as NP-hard
problems and researchers strongly recommend using heuristic
methods. This paper presents a new heuristic approach called the
critical task method (CTM) for solving U-shape assembly line
balancing problems. The performance of the proposed heuristic
method is tested by solving a number of test problems and comparing
them with 12 other heuristics available in the literature to confirm the
superior performance of the proposed heuristic. Furthermore, to
prove the efficiency of the proposed CTM, the objectives are
increased to minimize the number of workstation (or equivalently
maximize line efficiency), and minimizing the smoothness index.
Finally, it is proven that the proposed heuristic is more efficient than
the others to solve the U-shape assembly line balancing problem.
Abstract: An adaptive Fuzzy Inference Perceptual model has
been proposed for watermarking of digital images. The model
depends on the human visual characteristics of image sub-regions in
the frequency multi-resolution wavelet domain. In the proposed
model, a multi-variable fuzzy based architecture has been designed to
produce a perceptual membership degree for both candidate
embedding sub-regions and strength watermark embedding factor.
Different sizes of benchmark images with different sizes of
watermarks have been applied on the model. Several experimental
attacks have been applied such as JPEG compression, noises and
rotation, to ensure the robustness of the scheme. In addition, the
model has been compared with different watermarking schemes. The
proposed model showed its robustness to attacks and at the same time
achieved a high level of imperceptibility.
Abstract: Nowadays companies strive to survive in a
competitive global environment. To speed up product
development/modifications, it is suggested to adopt a collaborative
product development approach. However, despite the advantages of
new IT improvements still many CAx systems work separately and
locally. Collaborative design and manufacture requires a product
information model that supports related CAx product data models. To
solve this problem many solutions are proposed, which the most
successful one is adopting the STEP standard as a product data model
to develop a collaborative CAx platform. However, the improvement
of the STEP-s Application Protocols (APs) over the time, huge
number of STEP AP-s and cc-s, the high costs of implementation,
costly process for conversion of older CAx software files to the STEP
neutral file format; and lack of STEP knowledge, that usually slows
down the implementation of the STEP standard in collaborative data
exchange, management and integration should be considered. In this
paper the requirements for a successful collaborative CAx system is
discussed. The STEP standard capability for product data integration
and its shortcomings as well as the dominant platforms for supporting
CAx collaboration management and product data integration are
reviewed. Finally a platform named LAYMOD to fulfil the
requirements of CAx collaborative environment and integrating the
product data is proposed. The platform is a layered platform to enable
global collaboration among different CAx software
packages/developers. It also adopts the STEP modular architecture
and the XML data structures to enable collaboration between CAx
software packages as well as overcoming the STEP standard
limitations. The architecture and procedures of LAYMOD platform
to manage collaboration and avoid contradicts in product data
integration are introduced.
Abstract: Due to the coexistence of different Radio Access
Technologies (RATs), Next Generation Wireless Networks (NGWN)
are predicted to be heterogeneous in nature. The coexistence of
different RATs requires a need for Common Radio Resource
Management (CRRM) to support the provision of Quality of Service
(QoS) and the efficient utilization of radio resources. RAT selection
algorithms are part of the CRRM algorithms. Simply, their role is to
verify if an incoming call will be suitable to fit into a heterogeneous
wireless network, and to decide which of the available RATs is most
suitable to fit the need of the incoming call and admit it.
Guaranteeing the requirements of QoS for all accepted calls and at
the same time being able to provide the most efficient utilization of
the available radio resources is the goal of RAT selection algorithm.
The normal call admission control algorithms are designed for
homogeneous wireless networks and they do not provide a solution
to fit a heterogeneous wireless network which represents the NGWN.
Therefore, there is a need to develop RAT selection algorithm for
heterogeneous wireless network. In this paper, we propose an
approach for RAT selection which includes receiving different
criteria, assessing and making decisions, then selecting the most
suitable RAT for incoming calls. A comprehensive survey of
different RAT selection algorithms for a heterogeneous wireless
network is studied.
Abstract: Visual inputs are one of the key sources from which
humans perceive the environment and 'understand' what is
happening. Artificial systems perceive the visual inputs as digital
images. The images need to be processed and analysed. Within the
human brain, processing of visual inputs and subsequent
development of perception is one of its major functionalities. In this
paper we present part of our research project, which aims at the
development of an artificial model for visual perception (or
'understanding') based on the human perceptive and cognitive
systems. We propose a new model for perception from visual inputs
and a way of understaning or interpreting images using the model.
We demonstrate the implementation and use of the model with a real
image data set.
Abstract: In Orthogonal Frequency Division Multiplexing (OFDM) systems, the peak to average power ratio (PAR) is much high. The clipping signal scheme is a useful method to reduce PAR. Clipping the OFDM signal, however, increases the overall noise level by introducing clipping noise. It is necessary to recover the figure of the original signal at receiver in order to reduce the clipping noise. Considering the continuity of the signal and the figure of the peak, we obtain a certain conic function curve to replace the clipped signal module within the clipping time. The results of simulation show that the proposed scheme can reduce the systems? BER (bit-error rate) 10 times when signal-to-interference-and noise-ratio (SINR) equals to 12dB. And the BER performance of the proposed scheme is superior to that of kim's scheme, too.
Abstract: The applications on numbers are across-the-board that there is much scope for study. The chic of writing numbers is diverse and comes in a variety of form, size and fonts. Identification of Indian languages scripts is challenging problems. In Optical Character Recognition [OCR], machine printed or handwritten characters/numerals are recognized. There are plentiful approaches that deal with problem of detection of numerals/character depending on the sort of feature extracted and different way of extracting them. This paper proposes a recognition scheme for handwritten Hindi (devnagiri) numerals; most admired one in Indian subcontinent our work focused on a technique in feature extraction i.e. Local-based approach, a method using 16-segment display concept, which is extracted from halftoned images & Binary images of isolated numerals. These feature vectors are fed to neural classifier model that has been trained to recognize a Hindi numeral. The archetype of system has been tested on varieties of image of numerals. Experimentation result shows that recognition rate of halftoned images is 98 % compared to binary images (95%).
Abstract: Through inward perceptions, we intuitively expect
distributed software development to increase the risks associated with
achieving cost, schedule, and quality goals. To compound this
problem, agile software development (ASD) insists one of the main
ingredients of its success is cohesive communication attributed to
collocation of the development team. The following study identified
the degree of communication richness needed to achieve comparable
software quality (reduce pre-release defects) between distributed and
collocated teams. This paper explores the relevancy of
communication richness in various development phases and its
impact on quality. Through examination of a large distributed agile
development project, this investigation seeks to understand the levels
of communication required within each ASD phase to produce
comparable quality results achieved by collocated teams. Obviously,
a multitude of factors affects the outcome of software projects.
However, within distributed agile software development teams, the
mode of communication is one of the critical components required to
achieve team cohesiveness and effectiveness. As such, this study
constructs a distributed agile communication model (DAC-M) for
potential application to similar distributed agile development efforts
using the measurement of the suitable level of communication. The
results of the study show that less rich communication methods, in
the appropriate phase, might be satisfactory to achieve equivalent
quality in distributed ASD efforts.
Abstract: One of the most important aspects expected from an
ERP system is to mange user\administrator manual documents
dynamically. Since an ERP package is frequently changed during its
implementation in customer sites, it is often needed to add new
documents and/or apply required changes to existing documents in
order to cover new or changed capabilities. The worse is that since
these changes occur continuously, the corresponding documents
should be updated dynamically; otherwise, implementing the ERP
package in the organization encounters serious risks. In this paper, we
propose a new architecture which is based on the agent oriented
vision and supplies the dynamic document generation expected from
ERP systems using several independent but cooperative agents.
Beside the dynamic document generation which is the main issue of
this paper, the presented architecture will address some aspects of
intelligence and learning capabilities existing in ERP.
Abstract: Ultra-wide band (UWB) communication is one of
the most promising technologies for high data rate wireless networks
for short range applications. This paper proposes a blind channel
estimation method namely IMM (Interactive Multiple Model) Based
Kalman algorithm for UWB OFDM systems. IMM based Kalman
filter is proposed to estimate frequency selective time varying
channel. In the proposed method, two Kalman filters are concurrently
estimate the channel parameters. The first Kalman filter namely
Static Model Filter (SMF) gives accurate result when the user is static
while the second Kalman filter namely the Dynamic Model Filter
(DMF) gives accurate result when the receiver is in moving state. The
static transition matrix in SMF is assumed as an Identity matrix
where as in DMF, it is computed using Yule-Walker equations. The
resultant filter estimate is computed as a weighted sum of individual
filter estimates. The proposed method is compared with other existing
channel estimation methods.
Abstract: Adopting Zakowski-s upper approximation operator
C and lower approximation operator C, this paper investigates
granularity-wise separations in covering approximation spaces. Some
characterizations of granularity-wise separations are obtained by
means of Pawlak rough sets and some relations among granularitywise
separations are established, which makes it possible to research
covering approximation spaces by logical methods and mathematical
methods in computer science. Results of this paper give further
applications of Pawlak rough set theory in pattern recognition and
artificial intelligence.
Abstract: Mobile robots are used in a large field of scenarios,
like exploring contaminated areas, repairing oil rigs under water,
finding survivors in collapsed buildings, etc. Currently, there is no
unified intuitive user interface (UI) to control such complex mobile
robots. As a consequence, some scenarios are done without the
exploitation of experience and intuition of human teleoperators.
A novel framework has been developed to embed a flexible and
modular UI into a complete 3-D virtual reality simulation system.
This new approach wants to access maximum benefits of human
operators. Sensor information received from the robot is prepared for
an intuitive visualization. Virtual reality metaphors support the
operator in his decisions. These metaphors are integrated into a real
time stereo video stream. This approach is not restricted to any
specific type of mobile robot and allows for the operation of different
robot types with a consistent concept and user interface.
Abstract: The evaluation of the question answering system is a major research area that needs much attention. Before the rise of domain-oriented question answering systems based on natural language understanding and reasoning, evaluation is never a problem as information retrieval-based metrics are readily available for use. However, when question answering systems began to be more domains specific, evaluation becomes a real issue. This is especially true when understanding and reasoning is required to cater for a wider variety of questions and at the same time achieve higher quality responses The research in this paper discusses the inappropriateness of the existing measure for response quality evaluation and in a later part, the call for new standard measures and the related considerations are brought forward. As a short-term solution for evaluating response quality of heterogeneous systems, and to demonstrate the challenges in evaluating systems of different nature, this research presents a black-box approach using observation, classification scheme and a scoring mechanism to assess and rank three example systems (i.e. AnswerBus, START and NaLURI).